STM32L041K6U6 - 32MHz Cortex-M0+ 32KB MCU | STMicroelectronics
部品番号: STM32L041K6U6 ✓ 生産中STM32L041K6U6 概要
An ultra-low-power microcontroller is an embedded semiconductor that balances processing capability with minimized energy consumption. The STM32L0 family sits within the hierarchy of 32-bit ARM Cortex-M embedded MCUs, combining a general-purpose core with Flash memory, RAM, analog conversion, timers, communication interfaces, and GPIO in one low-power device. The STM32L041K6U6 is appropriate when a design must occupy little board area and operate from limited energy budgets without requiring a high-performance Cortex-M processor.
The headline characteristics are a 32 MHz Cortex-M0+ core, 32 KB of Flash memory, and a compact 32-pin UFQFPN package. The manufacturer identifies the STM32L041x6 as an access-line ultra-low-power family. Its 32-bit RISC architecture supports efficient control-loop execution, while the 5 mm by 5 mm package supports compact industrial, consumer, sensor, and connected-equipment designs.
The integrated MCU architecture combines the Cortex-M0+ processing core with embedded memory, GPIO, timers, communication peripherals, debug facilities, and an ADC. This integration reduces the component count of a control board by consolidating a processor, memory, and common peripherals in one package. Software development can use the STM32 embedded ecosystem, including configuration tools, peripheral libraries, debug adapters, and established Cortex-M toolchains.
Typical applications include low-power sensor nodes, industrial condition-monitoring equipment, compact access controls, battery-assisted measurement instruments, small motor-control modules, and energy-conscious embedded products. Its small footprint is particularly useful where PCB area is constrained and the system must combine control functions with communications or analog sensing.
Designers should confirm the complete pin assignment, exposed-pad connection, decoupling requirements, operating voltage, and supported temperature grade against the manufacturer datasheet before layout. Because the UFQFPN thermal pad is electrically and thermally significant, the PCB should follow the recommended land pattern and provide adequate ground-plane continuity for stable operation.
This page combines manufacturer specifications, package and ordering-code distinctions, application guidance, and drop-in replacement analysis for engineers evaluating the STM32L041K6U6. It is intended to accelerate component selection, PCB planning, firmware qualification, and second-source assessment.
ドロップイン代替品: STM32L041K6U6 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: STM32L041K6U6 (同一形状・フットプリント) — 相違点: Flash Memory, Package, Package Dimensions, Product Type.
STM32L041K6U6D
✅ ドロップイン📋 参考代替品(カタログ未掲載)
STM32L041K6U7
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
STM32L041K6U6U7
✅ ドロップイン📋 参考代替品(カタログ未掲載)
STM32L031K6U6
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →STM32L031K6U6D
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
STM32L041K6U6 最大定格&電気的特性
| Product Type | 32-bit ARM Cortex-M0+ microcontroller |
| Core Architecture | Arm Cortex-M0+ 32-bit RISC |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 32 KB (32K x 8 bits) |
| Programmable GPIO Count | 27 I/O |
| パッケージ | 32-pin UFQFPN |
| Package Dimensions | 5 mm x 5 mm |
| 実装タイプ | Surface mount |
| Product Family | STM32L041x6 access line |
| Power Class | Ultra-low-power |
| Embedded Security | AES hardware encryption |
STM32L041K6U6 5 mm x 5 mm ピン配置ガイド
STM32L041K6U6 (5 mm x 5 mm パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: STM32L041K6U6.
詳細は データシート をご参照ください。
主な用途
STM32L041K6U6 の用途: 6 件s: Low-Power Sensor Nodes, Industrial Condition Monitoring, Compact Access Control, Battery-Powered Measurement Instruments, Small Motor and Actuator Control, Connected Energy and Asset Tracking.
Low-Power Sensor Nodes
The STM32L041K6U6 fits compact sensor nodes because its Arm Cortex-M0+ core executes at 32 MHz while the device belongs to STMicroelectronics' ultra-low-power STM32L0 access line. The 32 KB of Flash supports acquisition logic, local filtering, configuration handling, and communication firmware without requiring a separate memory component. Its 32-pin UFQFPN footprint occupies only 5 mm by 5 mm, leaving room for sensors and radio hardware in a small board. Use the device to support periodic measurement, local threshold decisions, and duty-cycled data transmission. The principal design consideration is selecting sleep or stop modes that reduce average current without exceeding wake-up latency or corrupting an acquisition sequence.
おすすめ
Industrial Condition Monitoring
The STM32L041K6U6 is appropriate for industrial condition-monitoring modules that combine periodic sampling with local event detection. Its 32-bit Cortex-M0+ architecture at 32 MHz can handle timers, digital filtering, status logging, and communication state machines, while 32 KB of Flash provides space for embedded control and diagnostic firmware. The small 5 mm by 5 mm UFQFPN package is valuable in densely populated sensor nodes and modular monitoring cards. Use the microcontroller to supervise vibration, temperature, or equipment-state inputs and transmit only meaningful events to reduce network traffic. Validate the exact ordering code against the deployment temperature, and place the exposed pad on a continuous thermal and ground plane according to the package drawing.
おすすめ
Compact Access Control
The STM32L041K6U6 supports compact access-control terminals where an 8-bit-class controller may be too constrained but a full application processor would be excessive. Its 32 MHz Cortex-M0+ core can execute credential handling, keypad or reader-interface logic, event management, indicator control, and encrypted communication tasks. The 32 KB Flash stores application firmware, while the ultra-low-power family positioning assists battery-operated designs. A 5 mm by 5 mm UFQFPN footprint allows the controller to coexist with a secure element, communications module, and power-management circuitry. During design review, confirm cryptographic implementation requirements, exact peripheral availability, and the expected lockout or standby-current behavior for the target battery source.
おすすめ
Battery-Powered Measurement Instruments
The STM32L041K6U6 is well suited to handheld or battery-powered measurement instruments that need deterministic control with a small memory and footprint budget. Its Cortex-M0+ processor runs at 32 MHz for timing, data acquisition, calibration, and user-interface tasks, while 32 KB of Flash accommodates compact application code and configuration data. The 5 mm by 5 mm UFQFPN package allows the controller to sit beside precision converters, displays, and protection circuitry. Use the MCU's low-power modes between measurements to extend battery life and use a crystal or external clock when measurement accuracy requires a stable time base. Power-loss behavior, brownout thresholds, ADC accuracy, and the memory map should be verified against the exact datasheet revision during design qualification.
おすすめ
Small Motor and Actuator Control
The STM32L041K6U6 can serve as the supervisory controller in compact motor and actuator modules where fast general-purpose processing is not required. Its 32 MHz Cortex-M0+ core is suited to PWM generation, encoder or position-signal monitoring, fault-state logic, and communication with a higher-level controller. The integrated microcontroller package reduces the board area needed for control, timing, and digital I/O, while the ultra-low-power family positioning supports efficient standby behavior in portable systems. Use the MCU to coordinate actuators and apply limits to movement commands. Confirm that the required timers, pin mapping, ADC channels, and safety shutdown paths match the target application, and provide local hardware shutdown because firmware alone should not be the sole protection for a moving mechanism.
おすすめ
Connected Energy and Asset Tracking
The STM32L041K6U6 is appropriate for compact energy-metering or asset-tracking modules that must periodically process sensor data and communicate through a serial interface. Its 32-bit Cortex-M0+ core at 32 MHz can manage timestamping, event filtering, local counters, and communication protocols, while 32 KB of Flash constrains firmware planning but remains practical for focused applications. The 5 mm by 5 mm UFQFPN package helps minimize the size of the tracking electronics. Use the microcontroller to collect measurements, maintain operating state, and activate the radio only when needed. Review the exact serial-peripheral configuration, low-power wake sources, Flash endurance expectations, and supply-current profile because these factors have a direct impact on field lifetime and battery replacement intervals.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: STM32L041K6U6 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | STM32L041K6U6D | STM32L041K6U7 | STM32L041K6U6U7 | STM32L031K6U6 | STM32L031K6U6D |
|---|---|---|---|---|---|---|
| Package | 32-pin UFQFPN (5x5 mm) | 32-pin UFQFPN (5x5 mm) | 32-pin UFQFPN (5x5 mm) | 32-pin UFQFPN (5x5 mm) | 32-pin UFQFPN (5x5 mm) | 32-pin UFQFPN (5x5 mm) |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| CPU Core | Arm Cortex-M0+ | Arm Cortex-M0+ | Arm Cortex-M0+ | Arm Cortex-M0+ | Arm Cortex-M0+ | Arm Cortex-M0+ |
| Maximum CPU Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Flash Memory | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB |
主な差別化要因
- 32 KB Flash in a compact 32-pin footprint (vs STM32L031K6U6)
- Direct same-family ordering-code alternative (vs STM32L041K6U6D)
- AES hardware encryption in the access-line platform (vs STM32L031K6U6)
- 32 MHz processing with 27 I/O (vs STM32L041K6U7)
設計ノート
Use the exact 32-pin UFQFPN land pattern and exposed-pad geometry from the manufacturer package drawing. Place all decoupling capacitors adjacent to their intended supply pins, provide a short return path for each capacitor, and avoid routing high-speed or high-current signals beneath the device where they can increase coupling. The exposed pad should be connected according to the datasheet recommendation and tied to the appropriate supply or ground structure rather than left floating.
Decouple each required supply rail with the capacitance and ESR range specified by the manufacturer, and account for startup current when the source is a battery or low-current regulator. Place bulk energy storage near the power source and local high-frequency ceramic capacitance near the MCU. Confirm brownout, operating-voltage, and maximum-clock conditions across the full temperature range because low-power operation does not remove the requirement for a stable supply during wake-up and flash writes.
Do not treat a shared package name as proof that every ordering code is automatically interchangeable. Before substituting an STM32L041 or STM32L031 device, compare the complete pin list, exposed-pad connection, voltage limits, temperature grade, ADC channels, timer features, boot options, crystal configuration, Flash organization, RAM, and firmware-driver support. Create a hardware regression test that exercises startup, low-power transitions, ADC accuracy, timers, communications, and debugger attachment.
Keep the ARM SWD programming and debug interface accessible, and route the reset circuit using the recommended components and topology. If an external crystal is used, preserve a short and symmetrical route with a quiet ground reference and keep switching-converter and high-current paths away from the oscillator network. Because the MCU can operate at 32 MHz, inspect the PCB for signal-integrity and electromagnetic-compatibility issues rather than treating the part solely as a low-speed controller.
コンプライアンス情報
No explicit compliance declarations were stated for this exact ordering code. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status on the manufacturer product page and in the current regional product documentation.