STM8L101F2U6ATR - 16MHz 4KB Low-Power MCU | STMicroelectronics
部品番号: STM8L101F2U6ATR ✓ 生産中STM8L101F2U6ATR 概要
An ultra-low-power microcontroller is an embedded controller designed to balance processing capability with minimized energy consumption. The STM8L device belongs to the STM8 family and the STM8L EnergyLite line, combining an 8-bit architecture, low-power operating modes, and compact package options. This makes it suitable for battery-operated sensors, portable instruments, and embedded control nodes where active-mode performance and standby efficiency both matter.
Key characteristics include operation from 1.65 V to 3.6 V, 4 KB of Flash program memory, and 2 KB of RAM. The peripheral set supports USART for serial communication, SPI for higher-speed synchronous links, and I2C for connecting sensors and other low-speed peripherals. Two comparator channels and multifunction timers support direct sensing, timing, and basic control functions without requiring separate devices.
The device uses an 8-bit STM8 architecture operating up to 16 MHz. Its compact 20-pin UFQFPN package has 18 available I/O ports, allowing a small number of external connections despite the limited pin count. The manufacturer identifies this part as an ultra-low-power microcontroller with an operating supply range of 1.65 V to 3.6 V, making it appropriate for low-voltage systems where supply efficiency is central to the design.
Typical uses include low-power sensor nodes, battery-powered monitors, compact industrial controls, wearable accessories, communication modules, and small appliance controllers. The combination of 4 KB Flash, 2 KB RAM, three serial interfaces, timers, and comparators supports a standalone control platform when firmware requirements remain modest. The small 3 x 3 mm footprint also assists designers who need to minimize board area.
For PCB implementation, place decoupling capacitors close to the supply and ground pins, route oscillator and reset signals away from noisy switching nodes, and preserve the exposed-pad thermal and electrical requirements specified by the manufacturer. Firmware and peripheral selection must also account for the limited 4 KB program memory; larger buffers, protocol stacks, or complex control logic may require a higher-memory STM8L device.
This page combines lifecycle, package, memory, interface, and power specifications with practical application guidance, replacement analysis, and design considerations. It is intended to help engineers assess whether the STM8L101F2U6ATR provides enough Flash, RAM, I/O, and low-power capability for compact embedded systems before committing the 20-pin footprint to a PCB design.
ドロップイン代替品: STM8L101F2U6ATR — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: STM8L101F2U6ATR (同一形状・フットプリント) — 相違点: Architecture, Flash Memory, RoHS Compliance.
STM8L101F2U6TR
✅ ドロップイン価格はお問い合わせください
データシートを見る →STM8L101F2U3A
✅ ドロップイン📋 参考代替品(カタログ未掲載)
STM8L101F2U6ATR 最大定格&電気的特性
| Architecture | 8-bit |
| 最大クロック周波数 | 16 MHz |
| Flash Memory | 4 KB |
| RAM | 2 KB |
| Supply Voltage Range | 1.65 V to 3.6 V |
| I/O Port Count | 18 |
| Total Pin Count | 20 pins |
| Package Type | 20-pin UFQFPN |
| Package Dimensions | 3 x 3 mm |
| Package Height | 0.60 mm |
| 実装タイプ | Surface mount |
| Timer Support | Multifunction timers |
| Comparator Support | Integrated comparators |
| Serial Interface | USART |
| Synchronous Serial Interface | SPI |
| Two-Wire Serial Interface | I2C |
| Product Family | STM8L EnergyLite |
| ライフサイクル状態 | Active |
| RoHS Compliance | RoHS compliant |
STM8L101F2U6ATR 0.60 mm ピン配置ガイド
STM8L101F2U6ATR (0.60 mm パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: STM8L101F2U6ATR.
詳細は データシート をご参照ください。
主な用途
STM8L101F2U6ATR の用途: 6 件s: Battery-Powered Sensor Nodes, Low-Power Industrial Monitoring, Portable Medical and Wellness Devices, Wearable and Smart-Home Accessories, Serial Communication Modules, Compact Appliance Controls.
Battery-Powered Sensor Nodes
The STM8L101F2U6ATR fits compact sensor nodes because its 1.65 V minimum supply voltage supports low-energy operation, while I2C and SPI provide flexible connections to sensing and conditioning components. The 16 MHz processor is sufficient for sensor configuration, filtering, threshold evaluation, and packet assembly, and the 4 KB Flash capacity keeps firmware focused. Two comparators can support direct threshold decisions, while multifunction timers can define measurement and sampling intervals. The principal design trade-off is memory: 2 KB RAM and 4 KB Flash require disciplined buffering and may not suit large wireless protocol stacks.
おすすめ
Low-Power Industrial Monitoring
The STM8L101F2U6ATR can serve as the supervisory controller in a low-power industrial monitor that watches digital sensors, indicators, and service inputs. Its 18 I/O ports provide a practical interface count in a 20-pin package, while the timers support periodic sampling and the comparators handle simple threshold events. Operation from 1.65 V to 3.6 V allows integration with low-energy industrial rails. Firmware should be checked against the 4 KB Flash limit, especially when adding event logging, configuration menus, or communications beyond the basic USART, SPI, or I2C interfaces.
おすすめ
Portable Medical and Wellness Devices
The STM8L101F2U6ATR is appropriate for compact wellness or medical-adjacent peripherals that perform simple control functions within tight size and power constraints. Its low-voltage operation can support coin-cell or energy-harvesting architectures, while comparators and timers can supervise sensing windows. USART, SPI, and I2C permit connection to sensors, storage, or host electronics without requiring a large external interface controller. The limited 4 KB Flash and 2 KB RAM make code economy essential, and any regulated medical use requires application-specific validation rather than reliance on general MCU ratings.
おすすめ
Wearable and Smart-Home Accessories
The STM8L101F2U6ATR can control a small wearable accessory or smart-home endpoint where a full application processor would be excessive. The 3 x 3 mm UFQFPN package preserves board area, the 16 MHz clock handles button, haptic, and sensor-management tasks, and the three serial interfaces support different peripheral mixes. Low-voltage operation is valuable in battery-operated products. Designers should avoid selecting it when local storage, graphical interaction, or a large standards-compliant radio stack would consume the available 4 KB Flash and 2 KB RAM.
おすすめ
Serial Communication Modules
The STM8L101F2U6ATR is well suited to a compact protocol bridge or configuration module built around USART, SPI, or I2C. Its multifunction timers can handle framing intervals or flow-control timing, while 18 I/O ports support status indicators and user inputs. The low 1.65 V operating limit provides flexibility for low-energy interface electronics. Firmware complexity is the key limitation: four kilobytes of Flash is suitable for focused protocol conversion but not for simultaneous support of many high-bandwidth stacks or extensive buffering.
おすすめ
Compact Appliance Controls
The STM8L101F2U6ATR can act as the main controller in a small appliance or utility device requiring modest logic, timing, and communications. Timers manage discrete actuators, comparators detect simple analog thresholds, and USART provides a service or programming path. Its 20-pin footprint and 18 available I/O ports reduce routing complexity in space-constrained products. Because the device provides only 4 KB Flash and 2 KB RAM, designers should reserve it for straightforward control tasks and consider a larger STM8L model when user interfaces, motor algorithms, or detailed diagnostics are required.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: STM8L101F2U6ATR — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | STM8L101F2U6TR | STM8L101F2U3A |
|---|---|---|---|
| Package | 20-pin UFQFPN (3 x 3 mm) | 20-pin UFQFPN (3 x 3 mm) | 20-pin UFQFPN (3 x 3 mm) |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Architecture | 8-bit | 8-bit | 8-bit |
| Maximum Clock Frequency | 16 MHz | 16 MHz | 16 MHz |
| Flash Memory | 4 KB | 4 KB | 4 KB |
| RAM | 2 KB | 2 KB | 2 KB |
| Supply Voltage Range | 1.65 V to 3.6 V | 1.65 V to 3.6 V | 1.65 V to 3.6 V |
| I/O Port Count | 18 | 18 | 18 |
| Serial Interfaces | USART, SPI, I2C | USART, SPI, I2C | USART, SPI, I2C |
主な差別化要因
- Compact 20-pin implementation with 18 I/O ports (vs STM8L101F2U6TR)
- Direct match for basic embedded-control requirements (vs STM8L101F2U3A)
- Three integrated serial interfaces in a 20-pin package (vs STM8L101F2U6TR)
設計ノート
Validate the complete power budget at the 1.65 V lower operating limit, including startup, sensor loads, and communication activity. Place the required input and output decoupling capacitors close to their corresponding pins and use the values, tolerances, and ESR requirements listed in the manufacturer datasheet. If the system also uses 3.3 V peripherals, confirm that the STM8L101F2U6ATR and every attached device have compatible input thresholds.
The 20-pin UFQFPN occupies only 3 x 3 mm, so land-pattern accuracy and assembly process capability are important. Follow the manufacturer package drawing for pad dimensions, pitch, solder-mask clearance, and exposed-pad connection. Use thermal vias where the recommended layout calls for them, maintain adequate solder-mask dams around fine-pitch pads, and confirm the component orientation against pin 1 before authorizing assembly.
The 4 KB Flash and 2 KB RAM limits are the most frequent design risks. Measure the linked firmware size, reserve space for boot or application updates, and avoid allocating large buffers on the stack. Also verify that each assumed alternate-function pin can be assigned simultaneously; the 18 I/O positions include pins used by clocks, reset, programming, and power functions, so the effective application I/O count may be lower.
Route oscillator, reset, and sensitive sensor inputs away from switching power nodes and high-speed SPI traces. Use a continuous ground reference beneath and around the compact package, keep decoupling return paths short, and avoid routing interrupt or communication signals between noisy power-stage components. If SPI is used at higher clock rates, inspect edge timing and grounding with an oscilloscope because the 16 MHz system clock limits how much margin is available for slow signal edges.
コンプライアンス情報
The product listing identifies the STM8L101F2U6ATR as RoHS compliant. No separate REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified for this exact ordering code.