STM8L101F2U6ATR - 16MHz 4KB Low-Power MCU | STMicroelectronics
부품 번호: STM8L101F2U6ATR ✓ 활성STM8L101F2U6ATR 개요
An ultra-low-power microcontroller is an embedded controller designed to balance processing capability with minimized energy consumption. The STM8L device belongs to the STM8 family and the STM8L EnergyLite line, combining an 8-bit architecture, low-power operating modes, and compact package options. This makes it suitable for battery-operated sensors, portable instruments, and embedded control nodes where active-mode performance and standby efficiency both matter.
Key characteristics include operation from 1.65 V to 3.6 V, 4 KB of Flash program memory, and 2 KB of RAM. The peripheral set supports USART for serial communication, SPI for higher-speed synchronous links, and I2C for connecting sensors and other low-speed peripherals. Two comparator channels and multifunction timers support direct sensing, timing, and basic control functions without requiring separate devices.
The device uses an 8-bit STM8 architecture operating up to 16 MHz. Its compact 20-pin UFQFPN package has 18 available I/O ports, allowing a small number of external connections despite the limited pin count. The manufacturer identifies this part as an ultra-low-power microcontroller with an operating supply range of 1.65 V to 3.6 V, making it appropriate for low-voltage systems where supply efficiency is central to the design.
Typical uses include low-power sensor nodes, battery-powered monitors, compact industrial controls, wearable accessories, communication modules, and small appliance controllers. The combination of 4 KB Flash, 2 KB RAM, three serial interfaces, timers, and comparators supports a standalone control platform when firmware requirements remain modest. The small 3 x 3 mm footprint also assists designers who need to minimize board area.
For PCB implementation, place decoupling capacitors close to the supply and ground pins, route oscillator and reset signals away from noisy switching nodes, and preserve the exposed-pad thermal and electrical requirements specified by the manufacturer. Firmware and peripheral selection must also account for the limited 4 KB program memory; larger buffers, protocol stacks, or complex control logic may require a higher-memory STM8L device.
This page combines lifecycle, package, memory, interface, and power specifications with practical application guidance, replacement analysis, and design considerations. It is intended to help engineers assess whether the STM8L101F2U6ATR provides enough Flash, RAM, I/O, and low-power capability for compact embedded systems before committing the 20-pin footprint to a PCB design.
드롭인 대체품: STM8L101F2U6ATR — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: STM8L101F2U6ATR (동일 폼 팩터 및 풋프린트) — 차이점: Architecture, Flash Memory, RoHS Compliance.
STM8L101F2U6TR
✅ 드롭인가격 문의
데이터시트 보기 →STM8L101F2U3A
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
STM8L101F2U6ATR 최대 정격 & 전기적 특성
| Architecture | 8-bit |
| 최대 클록 주파수 | 16 MHz |
| Flash Memory | 4 KB |
| RAM | 2 KB |
| Supply Voltage Range | 1.65 V to 3.6 V |
| I/O Port Count | 18 |
| Total Pin Count | 20 pins |
| Package Type | 20-pin UFQFPN |
| Package Dimensions | 3 x 3 mm |
| Package Height | 0.60 mm |
| 실장 유형 | Surface mount |
| Timer Support | Multifunction timers |
| Comparator Support | Integrated comparators |
| Serial Interface | USART |
| Synchronous Serial Interface | SPI |
| Two-Wire Serial Interface | I2C |
| Product Family | STM8L EnergyLite |
| 수명 주기 상태 | Active |
| RoHS Compliance | RoHS compliant |
STM8L101F2U6ATR 0.60 mm 핀 구성 가이드
STM8L101F2U6ATR(0.60 mm 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: STM8L101F2U6ATR.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
STM8L101F2U6ATR 적합 용도: 6 애플리케이션s: Battery-Powered Sensor Nodes, Low-Power Industrial Monitoring, Portable Medical and Wellness Devices, Wearable and Smart-Home Accessories, Serial Communication Modules, Compact Appliance Controls.
Battery-Powered Sensor Nodes
The STM8L101F2U6ATR fits compact sensor nodes because its 1.65 V minimum supply voltage supports low-energy operation, while I2C and SPI provide flexible connections to sensing and conditioning components. The 16 MHz processor is sufficient for sensor configuration, filtering, threshold evaluation, and packet assembly, and the 4 KB Flash capacity keeps firmware focused. Two comparators can support direct threshold decisions, while multifunction timers can define measurement and sampling intervals. The principal design trade-off is memory: 2 KB RAM and 4 KB Flash require disciplined buffering and may not suit large wireless protocol stacks.
추천
Low-Power Industrial Monitoring
The STM8L101F2U6ATR can serve as the supervisory controller in a low-power industrial monitor that watches digital sensors, indicators, and service inputs. Its 18 I/O ports provide a practical interface count in a 20-pin package, while the timers support periodic sampling and the comparators handle simple threshold events. Operation from 1.65 V to 3.6 V allows integration with low-energy industrial rails. Firmware should be checked against the 4 KB Flash limit, especially when adding event logging, configuration menus, or communications beyond the basic USART, SPI, or I2C interfaces.
추천
Portable Medical and Wellness Devices
The STM8L101F2U6ATR is appropriate for compact wellness or medical-adjacent peripherals that perform simple control functions within tight size and power constraints. Its low-voltage operation can support coin-cell or energy-harvesting architectures, while comparators and timers can supervise sensing windows. USART, SPI, and I2C permit connection to sensors, storage, or host electronics without requiring a large external interface controller. The limited 4 KB Flash and 2 KB RAM make code economy essential, and any regulated medical use requires application-specific validation rather than reliance on general MCU ratings.
추천
Wearable and Smart-Home Accessories
The STM8L101F2U6ATR can control a small wearable accessory or smart-home endpoint where a full application processor would be excessive. The 3 x 3 mm UFQFPN package preserves board area, the 16 MHz clock handles button, haptic, and sensor-management tasks, and the three serial interfaces support different peripheral mixes. Low-voltage operation is valuable in battery-operated products. Designers should avoid selecting it when local storage, graphical interaction, or a large standards-compliant radio stack would consume the available 4 KB Flash and 2 KB RAM.
추천
Serial Communication Modules
The STM8L101F2U6ATR is well suited to a compact protocol bridge or configuration module built around USART, SPI, or I2C. Its multifunction timers can handle framing intervals or flow-control timing, while 18 I/O ports support status indicators and user inputs. The low 1.65 V operating limit provides flexibility for low-energy interface electronics. Firmware complexity is the key limitation: four kilobytes of Flash is suitable for focused protocol conversion but not for simultaneous support of many high-bandwidth stacks or extensive buffering.
추천
Compact Appliance Controls
The STM8L101F2U6ATR can act as the main controller in a small appliance or utility device requiring modest logic, timing, and communications. Timers manage discrete actuators, comparators detect simple analog thresholds, and USART provides a service or programming path. Its 20-pin footprint and 18 available I/O ports reduce routing complexity in space-constrained products. Because the device provides only 4 KB Flash and 2 KB RAM, designers should reserve it for straightforward control tasks and consider a larger STM8L model when user interfaces, motor algorithms, or detailed diagnostics are required.
추천
추천 제품 요약
엔지니어링 참조 데이터: STM8L101F2U6ATR — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | STM8L101F2U6TR | STM8L101F2U3A |
|---|---|---|---|
| Package | 20-pin UFQFPN (3 x 3 mm) | 20-pin UFQFPN (3 x 3 mm) | 20-pin UFQFPN (3 x 3 mm) |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Architecture | 8-bit | 8-bit | 8-bit |
| Maximum Clock Frequency | 16 MHz | 16 MHz | 16 MHz |
| Flash Memory | 4 KB | 4 KB | 4 KB |
| RAM | 2 KB | 2 KB | 2 KB |
| Supply Voltage Range | 1.65 V to 3.6 V | 1.65 V to 3.6 V | 1.65 V to 3.6 V |
| I/O Port Count | 18 | 18 | 18 |
| Serial Interfaces | USART, SPI, I2C | USART, SPI, I2C | USART, SPI, I2C |
주요 차별점
- Compact 20-pin implementation with 18 I/O ports (vs STM8L101F2U6TR)
- Direct match for basic embedded-control requirements (vs STM8L101F2U3A)
- Three integrated serial interfaces in a 20-pin package (vs STM8L101F2U6TR)
설계 노트
Validate the complete power budget at the 1.65 V lower operating limit, including startup, sensor loads, and communication activity. Place the required input and output decoupling capacitors close to their corresponding pins and use the values, tolerances, and ESR requirements listed in the manufacturer datasheet. If the system also uses 3.3 V peripherals, confirm that the STM8L101F2U6ATR and every attached device have compatible input thresholds.
The 20-pin UFQFPN occupies only 3 x 3 mm, so land-pattern accuracy and assembly process capability are important. Follow the manufacturer package drawing for pad dimensions, pitch, solder-mask clearance, and exposed-pad connection. Use thermal vias where the recommended layout calls for them, maintain adequate solder-mask dams around fine-pitch pads, and confirm the component orientation against pin 1 before authorizing assembly.
The 4 KB Flash and 2 KB RAM limits are the most frequent design risks. Measure the linked firmware size, reserve space for boot or application updates, and avoid allocating large buffers on the stack. Also verify that each assumed alternate-function pin can be assigned simultaneously; the 18 I/O positions include pins used by clocks, reset, programming, and power functions, so the effective application I/O count may be lower.
Route oscillator, reset, and sensitive sensor inputs away from switching power nodes and high-speed SPI traces. Use a continuous ground reference beneath and around the compact package, keep decoupling return paths short, and avoid routing interrupt or communication signals between noisy power-stage components. If SPI is used at higher clock rates, inspect edge timing and grounding with an oscilloscope because the 16 MHz system clock limits how much margin is available for slow signal edges.
규정 준수 정보
The product listing identifies the STM8L101F2U6ATR as RoHS compliant. No separate REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified for this exact ordering code.