STSPIN32F0602 - 600V Three-Phase BLDC SiP | STMicroelectronics
部品番号: STSPIN32F0602 ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $5.54 | $5.54 |
| 10 | $5.21 | $52.10 |
| 100 | $4.85 | $485.00 |
| 500 | $4.42 | $2,210.00 |
| 1,000 | $4.05 | $4,050.00 |
STSPIN32F0602 概要
A system-in-package for motor control combines an MCU core, gate drivers, and housekeeping supplies in a single molded body, dramatically shrinking PCB footprint and bill-of-material versus a discrete implementation. The STSPIN32F0602 belongs to the broader motor-driver / motor-controller category, which sits hierarchically under power management, motion control, and embedded motor-control ICs; it specifically targets sub-1 kW three-phase BLDC and PMSM applications where integration outweighs the need for separate MCU selection.
Key features of the STSPIN32F0602 include three high-voltage/low-voltage gate-driver channels capable of driving N-channel power MOSFETs or IGBTs, an integrated bootstrap diode structure, an embedded STM32F0 Cortex-M0 core, on-chip flash memory, and comprehensive protection including interlocking, deadtime generation, and shutdown on undervoltage. The device is housed in a 64-pin TQFP-EP (10x10 mm) package with an exposed thermal pad that conducts dissipated heat directly to the PCB copper pour, supporting continuous switching at high bus voltages.
Architecturally, the SiP isolates the low-voltage digital MCU from the high-voltage analog gate-driver domain, allowing firmware developers to use the standard STM32 toolchain (STM32CubeMX, STM32CubeIDE, ST-LINK) while keeping the analog front end isolated and protected. The gate drivers sink/source sufficient current to switch typical 600 V MOSFETs at tens of kHz, while the integrated bootstrap circuitry eliminates the need for an external bootstrap diode on each high-side channel, reducing BOM count by six discrete components.
Typical applications include home appliances such as refrigerator compressors, washing-machine direct-drive motors, and air-conditioner outdoor-unit fans; industrial pumps, fans, and small servo drives; and 600 V-class three-phase inverters where design teams prefer a single qualified IC over a discrete MCU + driver + bootstrap network. The device also suits HVAC blowers and low-power industrial automation drives.
When designing with the STSPIN32F0602, ensure the exposed thermal pad is soldered to a sufficient copper area to keep junction temperature within the datasheet limits, and follow the reference schematic in the EVSPIN32F0602S1 evaluation board for the recommended input filter, bulk bus capacitance, and shunt-based current-sensing network. Programming requires an SWD interface; the device is supported by the standard STM32Cube ecosystem, allowing firmware reuse across the STSPIN32 family.
This page synthesizes distributor pricing, parametric drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone. As of 2026-10-10, the STSPIN32F0602 is broadly stocked at distributors including DigiKey, Mouser, and the ST eStore, with pricing in the typical industrial SiP range.
ドロップイン代替品: STSPIN32F0602 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: STSPIN32F0602 （同一形状・フットプリント） — 相違点: Bootstrap Diodes, MSL Level, Product Type.
クイック比較ツール — 並列比較する代替部品を選択:
STSPIN32F0601
✅ ドロップイン📋 参考代替品（カタログ未掲載）
STSPIN32F0252
✅ ドロップイン📋 参考代替品（カタログ未掲載）
STSPIN32F0602 最大定格＆電気的特性
| Product Type | System-in-Package (SiP) - 3-phase BLDC controller |
| Integrated MCU Core | ARM Cortex-M0 STM32 |
| On-chip Flash | 32 kB |
| High-Voltage Rail | up to 600 V |
| Gate Driver Channels | 3-phase (high-side + low-side) |
| External Switch Type | N-channel MOSFET or IGBT |
| Bootstrap Diodes | Integrated |
| Deadtime Generation | Yes (internal) |
| Interlock Protection | Yes |
| Undervoltage Lockout | Yes |
| パッケージ | TQFP-64 (10x10 mm) with Exposed Pad |
| 実装タイプ | Surface Mount |
| 動作温度 | -40C to +125C |
| MSLレベル | 3 (per JEDEC J-STD-020) |
| RoHS ステータス | Compliant |
STSPIN32F0602 tqfp-64 (10x10 mm) with exposed pad ピン配置ガイド
STSPIN32F0602 (tqfp-64 (10x10 mm) with exposed pad パッケージ) のピン配置。 このパワーデバイスは、ゲート、ドレイン、ソース端子を備えています。非極性パッケージの場合、正確なピン1の向きとフットプリントの詳細については、メーカーのデータシートを参照してください。主な用途には、電源設計、モータ駆動、負荷スイッチングがあります。
詳細なピン配置データはありません: STSPIN32F0602.
詳細は データシート をご参照ください。
主な用途
STSPIN32F0602 の用途: 6 件s: Home Appliance BLDC Compressor Drives, Washing Machine Direct-Drive Motors, HVAC Outdoor Unit Fan Drives, Industrial Pumps and Fans, Servo Drives and Robotics Sub-1 K Joints, Low-Power Three-Phase Solar Inverters.
Home Appliance BLDC Compressor Drives
The STSPIN32F0602 is well suited for refrigerator compressor and freezer BLDC inverter boards because its 600 V high-voltage rail directly handles the rectified 110/220/230 VAC bus without an additional pre-regulator. The integrated ARM Cortex-M0 STM32 core runs field-oriented control (FOC) firmware at sufficient loop rate for sub-200 W to 1 kW compressors, while the embedded three-phase gate driver eliminates six external bootstrap diodes and shrinks the PCB to fit inside a sealed compressor housing. Engineers benefit from shorter certification cycles because the SiP comes with full ST characterization, and the TQFP-64 (10x10 mm) exposed-pad package provides the thermal headroom needed for continuous switching at high bus voltages. The EVSPIN32F0602S1 reference design accelerates time-to-market by reusing its input filter and shunt-sensing layout.
おすすめ
Washing Machine Direct-Drive Motors
Direct-drive washing-machine drum motors benefit from the STSPIN32F0602 because its integrated STM32 MCU and gate-driver pair remove the need for a separate control board, allowing the power and logic stages to coexist on a single PCB inside the appliance base. The 600 V rail supports 220 VAC-derived DC buses common in global washer designs, and the integrated deadtime generation prevents shoot-through at high drum spin speeds. Designers benefit from reduced BOM and faster EMC qualification. The exposed thermal pad of the TQFP-64 package conducts heat to the chassis-mounted PCB copper pour, supporting the high continuous RMS current typical of direct-drive drum wash cycles. The STM32CubeMX firmware ecosystem accelerates motor-tuning loop development for engineers.
おすすめ
HVAC Outdoor Unit Fan Drives
Air-conditioner outdoor-unit fans and HVAC blowers run on three-phase BLDC motors that the STSPIN32F0602 can drive directly from a 600 V rectified bus. The integrated gate driver supports the typical 10-20 kHz PWM frequencies used to keep acoustic noise outside the audible band, while the on-chip Cortex-M0 STM32 MCU runs sinusoidal FOC firmware with sensorless back-EMF detection, reducing harness complexity. Engineers benefit from the device's interlock and undervoltage-lockout protection, which guards against high-side/low-side cross-conduction during brownout events common in HVAC outdoor installations. The TQFP-64 footprint fits within the IPM-style PCB outline preferred by HVAC module makers.
おすすめ
Industrial Pumps and Fans
Small industrial pumps and fans from 100 W to 1 kW benefit from the STSPIN32F0602's 600 V rating because it covers 480 V three-phase class industrial inputs via rectification, eliminating an extra conversion stage. The integrated bootstrap structure and three-phase gate driver allow the design to drive standard 600 V MOSFET half-bridges or IGBT modules without external high-side driver ICs. The exposed thermal pad of the TQFP-64 package supports the continuous 1-2 A RMS phase currents typical of small industrial drives. The STM32 firmware ecosystem provides sensorless and sensored FOC libraries, accelerating time-to-market for industrial-drive engineers.
おすすめ
Servo Drives and Robotics Sub-1 K Joints
Collaborative robot and small servo-drive joints in the 50-500 W range benefit from the STSPIN32F0602 because the device integrates the MCU and three-phase gate driver into one 10x10 mm TQFP-64 footprint, allowing the drive to fit inside the motor can or joint housing. The integrated STM32 Cortex-M0 runs position-velocity-torque control loops at the rates required by collaborative robotics, while the 600 V rating covers DC-bus systems up to 380 VDC derived from industrial 230 VAC. Engineers benefit from the EVSPIN32F0602S1 reference design's tuning procedure, which can be adapted for servo commissioning. The exposed-pad package supports the high switching frequency typical of low-inductance servo motors.
おすすめ
Low-Power Three-Phase Solar Inverters
Small single-phase solar inverters in the 500 W to 1 kW range benefit from the STSPIN32F0602 because the 600 V high-voltage rail directly accepts 400 V-class solar string open-circuit voltages after rectification, with the integrated MCU running MPPT and grid-sync firmware. The integrated gate driver supports the 20-50 kHz switching frequencies needed for compact magnetics in solar micro-inverters, while the STM32 firmware ecosystem provides power-conversion libraries that simplify grid-tie certification. Engineers benefit from reduced BOM versus discrete MCU + driver solutions, lowering the bill of material critical to micro-inverter commercial viability. The TQFP-64 exposed-pad package supports outdoor junction-box thermal environments when properly heatsinked.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: STSPIN32F0602 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | STSPIN32F0601 | STSPIN32F0252 |
|---|---|---|---|
| Package | TQFP-64 (10x10 mm) Exposed Pad | TQFP-64 (10x10 mm) Exposed Pad - same | TQFP-64 (10x10 mm) Exposed Pad - same |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| High-Voltage Rail | 600 V | 600 V (same) | 250 V |
| Integrated MCU | ARM Cortex-M0 STM32 | ARM Cortex-M0 STM32 (same) | ARM Cortex-M0 STM32 (same) |
| Gate Driver Phases | 3-phase | 3-phase (same) | 3-phase (same) |
| Bootstrap Diodes | Integrated | Integrated (same) | Integrated (same) |
| Operating Temperature | -40C to +125C | -40C to +125C (same) | -40C to +125C (same) |
主な差別化要因
- Highest high-voltage rail rating in STSPIN32 family （vs STSPIN32F0252)
- Same SiP architecture and TQFP-64 package as STSPIN32F0601 （vs STSPIN32F0601)
- Integrated bootstrap diodes reduce BOM by 6 components （vs Discrete MCU + gate driver approach)
設計ノート
Estimated: at continuous 1 A RMS phase current switching 600 V MOSFETs at 20 kHz, the STSPIN32F0602 gate-driver section dissipates approximately 0.3-0.5 W internally, dominated by gate-charge losses. The TQFP-64 exposed-pad package must be soldered to at least 1 square inch of top-layer copper pour with thermal vias to the bottom layer. Without adequate copper, junction temperature can exceed 125 C at high ambient, triggering thermal shutdown. Always measure the package temperature in a worst-case thermal chamber to confirm margin against the 125 C maximum.
Place the STSPIN32F0602 such that the high-voltage gate-driver output pins route directly to the power MOSFET/IGBT gates with minimal parasitic inductance. Keep the bootstrap capacitor traces short and place a 100 nF X7R ceramic bypass capacitor close to each low-voltage supply pin. Use a four-layer PCB with a dedicated ground plane for the analog return and a separate noisy power-ground island under the gate-driver section, stitched together at a single point near the shunt resistor. Follow the EVSPIN32F0602S1 reference layout as the starting baseline.
Do not omit the bootstrap capacitors - without them, the high-side gate drivers will fail to turn on and the motor will run only partially. Do not exceed the 600 V high-voltage rail rating during DC-link overshoot - size the bulk capacitor to limit ripple and add a TVS clamp for transient suppression. The integrated STM32 MCU requires an SWD programming interface; design the PCB with test points for SWDIO, SWCLK, NRST, and GND to enable field firmware updates. Verify deadtime is enabled in firmware before applying high PWM duty cycles to prevent shoot-through.
コンプライアンス情報
RoHS compliant per ST product page. Not AEC-Q100 qualified - this is a home/industrial grade part. For automotive motor-control applications, evaluate STSPIN32G4 automotive-qualified variants.
