SY88773VMI - 3.2Gbps CML Limiting Postamplifier | Microchip
部品番号: SY88773VMI ✗ 生産終了SY88773VMI 概要
A limiting postamplifier is a specialized amplifier IC used after a photodiode or transimpedance amplifier in optical communications equipment. Its position in the receiver path is between the front-end detector stage and the clock-and-data-recovery circuitry. The SY88773VMI combines signal conditioning, amplitude limiting, and loss-of-signal monitoring in one compact integrated circuit, supporting dense optical-network equipment designs.
Key features include operation from 3.3V or 5V, data rates up to 3.2Gbps, and a CML interface suitable for high-speed optical modules. The TTL loss-of-signal output gives the surrounding system an independent indication that the recovered signal has fallen outside the usable operating range. Its 16-MLF package is only 3x3 mm, helping conserve board area in compact optical transceivers.
The limiting stage is intended to provide a stable digital output when the upstream receiver produces a sufficiently large signal but clean up residual amplitude variation at the decision point. CML signaling is appropriate for high-speed point-to-point links because it supports high data rates and helps maintain controlled signal levels. System-level performance still depends on the preceding detector, equalization, termination, and clock-and-data-recovery circuitry.
Typical applications include SONET, SDH, and other optical-network receiver subsystems, as well as high-speed optical-module designs where a compact limiting postamplifier and independent TTL loss-of-signal status are useful. The device can also be evaluated in laboratory receiver prototypes when the data rate and optical front end are compatible with its operating characteristics.
PCB implementation requires careful treatment of high-speed differential signals. Keep CML routing short and symmetric, provide the correct impedance environment, and place bypass and termination components close to their associated pins. Review the manufacturer's pin description and recommended application circuit before assigning tracks, especially around supply, ground, and loss-of-signal connections.
This product record combines the exact package and interface identifiers with application-focused guidance for optical receiver design. It also distinguishes a genuine replacement requirement from ordinary functional equivalence: a candidate must use the same 16-MLF footprint, preserve pin-to-pin connectivity, and meet the relevant data-rate and interface requirements before it can be considered drop-in compatible.
ドロップイン代替品: SY88773VMI — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
この製品に利用可能なドロップイン代替品はありません。
代替品をリクエストSY88773VMI 最大定格&電気的特性
| Product Type | Limiting postamplifier IC |
| Manufacturer | Microchip Technology |
| Supported Supply Voltage | 3.3V or 5V |
| Maximum Data Rate | 3.2 Gbps |
| High-Speed Output Interface | CML |
| Loss-of-Signal Output | TTL-compatible |
| Power Class | Low-power |
| Application | Fiber-optic receiver signal conditioning |
| パッケージ | 16-MLF (3x3 mm) |
| 実装タイプ | Surface mount |
| ピン数 | 16 pins |
SY88773VMI 16-mlf (3x3 mm) ピン配置ガイド
SY88773VMI (16-mlf (3x3 mm) パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: SY88773VMI.
詳細は データシート をご参照ください。
主な用途
SY88773VMI の用途: 6 件s: Fiber-Optic Receiver Signal Conditioning, SONET Optical Receiver Subsystems, SDH Optical Receiver Modules, High-Speed Optical Transceiver Modules, Optical-Link Test Equipment, Legacy Networking Equipment Maintenance.
Fiber-Optic Receiver Signal Conditioning
The SY88773VMI fits directly after a photodiode or transimpedance amplifier in a high-speed optical receiver because it performs the limiting postamplifier function and delivers the result through a CML output. Its maximum data rate of 3.2Gbps makes it appropriate for legacy 2.5Gbit/s-class receiver paths and other optical links operating within the manufacturer-defined limits. The TTL loss-of-signal output adds a useful monitoring function without occupying a separate indicator IC. Because this is a low-power device in a 16-MLF 3x3 mm package, it also supports compact transceiver layouts where PCB area and supply consumption are important constraints.
おすすめ
SONET Optical Receiver Subsystems
The SY88773VMI is suitable for legacy optical-network receiver subsystems requiring a compact limiting stage near the optical front end. Its 3.2Gbps maximum data rate covers the intended high-speed recovery function, while the CML interface provides a standard high-speed output for the following receiver stage. The separate TTL loss-of-signal indication can supervise receiver health at the system level. In a SONET-oriented design, engineers should verify timing, jitter, sensitivity, and supply-distribution requirements against the manufacturer datasheet before release, especially when operating the obsolete part in a maintained or certified system.
おすすめ
SDH Optical Receiver Modules
The SY88773VMI can serve as the limiting postamplifier in an SDH-class optical receiver module when the supported link rate, signal levels, and timing margins meet the design requirements. Its low-power 3.3V/5V operation supports compact line-card and transceiver construction, while the 16-MLF package minimizes footprint. The CML output supports connection to subsequent clock-recovery or decision circuitry, and TTL LOS provides a convenient fault-status input. Because the device is discontinued, a new SDH platform should normally use a supported device unless maintaining an installed base, and any substitution must be checked for complete pin and timing compatibility.
おすすめ
High-Speed Optical Transceiver Modules
The SY88773VMI is applicable to the receive side of compact optical transceiver modules where a limiting postamplifier, CML data output, and loss-of-signal status are required in one device. Supporting 3.3V and 5V operation allows alignment with different module supply architectures, while the 3x3 mm 16-MLF package helps preserve board area. The receiver designer must still provide correct CML termination, low-impedance supply routing, stable reference planes, and an adequate thermal path. For new transceiver platforms, confirm current product availability before committing the obsolete SY88773VMI to a production BOM.
おすすめ
Optical-Link Test Equipment
The SY88773VMI can be incorporated into laboratory optical-link test equipment when a receiver subsection requires amplification, limiting, and signal-loss monitoring in a compact area. The CML output can drive compatible test electronics, while TTL LOS gives the tester a direct indication of the recovered input state. Its 3.2Gbps rate supports high-speed test scenarios rather than low-speed diagnostic links. Instrument designers should account for the exact input sensitivity, jitter contribution, propagation delay, and output levels stated in the manufacturer datasheet, and should validate channel losses across temperature before using the part as a generic bench amplifier.
おすすめ
Legacy Networking Equipment Maintenance
The SY88773VMI is particularly relevant to maintenance and repair of legacy networking equipment whose receiver board was designed around this exact 16-MLF limiting postamplifier. Retaining the established part can avoid respinning a high-speed optical PCB and preserve the original CML and TTL loss-of-signal behavior. Engineers should request current inventory and traceability information, inspect each device, and confirm the exact MPN before installation. A substitute should be considered only after comparing the terminal assignment, package geometry, electrical performance, and timing behavior because cross-reference search results alone do not establish drop-in compatibility.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: SY88773VMI — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 |
|---|---|
| Package | 16-MLF (3x3 mm) |
| Brand | Microchip Technology |
| Product Type | Limiting postamplifier IC |
| Supported Supply Voltage | 3.3V or 5V |
| Maximum Data Rate | 3.2 Gbps |
| High-Speed Output Interface | CML |
| Loss-of-Signal Output | TTL-compatible |
| Power Class | Low-power |
| Target Application | Fiber-optic receiver signal conditioning |
| Lifecycle Status | Obsolete |
主な差別化要因
- Integrated receiver monitoring (vs Generic low-power amplifier)
- Space-efficient optical receiver integration (vs Larger-package limiting postamplifier)
- Dual common supply options (vs Single-supply limiting amplifier)
設計ノート
Route the CML signal path as a short, symmetric differential connection and provide the termination arrangement specified by the manufacturer application circuit. Keep high-speed nodes away from supply-routing discontinuities and ground-plane edges. The 16-MLF footprint is compact, so escape routing should be planned before component placement to avoid long copper stubs and unnecessary impedance discontinuities.
Assign the board footprint from the official 16-MLF package drawing, including exposed-pad, solder-mask, paste, and thermal-via requirements. Do not infer the land pattern from a generic 16-pin QFN library entry. Verify pin-one orientation and the distinction between the package terminal numbering and the schematic symbol before fabrication to prevent an irreversible high-speed layout error.
Follow the manufacturer supply and decoupling recommendations when operating from either 3.3V or 5V. Place bypass components close to the supply terminals, maintain a continuous return path, and avoid sharing narrow neck regions between sensitive input/output routing and unrelated digital currents. Confirm the actual supply current and tolerance requirements from the datasheet before sizing the power-distribution network.
Do not treat a general-purpose limiting amplifier as a drop-in replacement without checking terminal mapping, CML output levels, TTL LOS polarity and timing, data rate, and package dimensions. Also confirm whether a candidate suffix denotes a different package form or ordering option. For the obsolete SY88773VMI, preserve traceability and perform appropriate incoming inspection when using remaining inventory in a maintained system.
コンプライアンス情報
No definitive environmental or automotive qualification status was identified for this discontinued MPN. Confirm material declarations and qualification records with Microchip Technology before use in regulated or automotive applications.