SY89823LHI - 500MHz 1:22 HSTL Clock Buffer | Microchip
部品番号: SY89823LHISY89823LHI 概要
A high-speed differential clock buffer is a clock and timing IC that reproduces a differential clock across multiple outputs while preserving signal integrity, edge alignment, and source impedance. In the broader semiconductor hierarchy, the SY89823LHI belongs to the clock-buffer and translator class within clock and timing integrated circuits. Its fanout function reduces the number of separate clock sources required by a multi-channel or multi-board system.
The headline operating specifications are a 3.3 V supply, operation up to 500 MHz, a 1:22 differential fanout ratio, and 1.5 V HSTL output signaling. The 64-pin TQFP exposed-pad package provides the physical interface for the input, 22 differential output channels, power connections, and control or configuration functions defined by the manufacturer. Its principal engineering benefit is consolidated high-speed clock distribution, reducing routing complexity when many destinations require the same differential clock.
At the circuit level, the device separates clock generation from clock distribution. A low-jitter source can feed the differential input, while the SY89823LHI supplies matched output branches for downstream circuits. Maintaining controlled impedance, short trace lengths, continuous return paths, and appropriate termination is essential when routing 500 MHz differential signals. The exposed thermal pad should be connected to the supply or ground plane as directed in the manufacturer datasheet and evaluated against the system thermal budget.
Typical design uses include processor and communications clock distribution, networking-equipment backplanes, high-speed serial-interface subsystems, FPGA clock trees, and multi-channel test equipment. The part is especially relevant where one differential clock must reach many receiving circuits and cable or board losses make local regeneration preferable to long point-to-point distribution. The system designer must also verify timing budget, return loss, channel skew, and power-supply behavior for the completed board.
A critical design consideration is that a 1:22 fanout does not eliminate endpoint-specific loading or trace differences. Each output should have a controlled termination and matched routing environment, while unused channels should be handled according to the manufacturer’s recommended termination scheme. Power and ground planes must provide low-impedance paths at 500 MHz, and bypass connections should be placed close to the supply pins to limit supply-noise coupling into the clock network.
This product page consolidates the device identification, electrical characteristics, application guidance, and engineering trade-offs needed to plan a clock-distribution design. It also separates verified device facts from parameters that must be confirmed in the manufacturer datasheet, helping engineers assess fit without relying on a simple distributor listing.
ドロップイン代替品: SY89823LHI — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
SY89823LHI-TR
✅ ドロップイン📋 参考代替品(カタログ未掲載)
SY89823LHI 仕様
| 電源電圧 | 3.3 V |
| 最大クロック周波数 | 500 MHz |
| Fanout Ratio | 1:22 differential |
| Number of Differential Outputs | 22 |
| Logic Standard | Differential HSTL |
| HSTL Output Voltage | 1.5 V |
| Device Type | High-performance bus clock driver, fanout buffer and translator |
| パッケージ | 64-pin TQFP with exposed pad |
| ピン数 | 64 pins |
| 実装タイプ | Surface mount |
SY89823LHI 64-pin tqfp with exposed pad ピン配置ガイド
SY89823LHI (64-pin tqfp with exposed pad パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: SY89823LHI.
詳細は データシート をご参照ください。
主な用途
SY89823LHI の用途: 6 件s: Communications Clock Distribution, Networking Equipment Backplane, FPGA and Processor Clock Trees, High-Speed Test Equipment, High-Speed Serial Interface Subsystems, Industrial Data Acquisition Systems.
Communications Clock Distribution
The SY89823LHI is suitable for centralizing a 500 MHz differential clock across a communications subsystem that needs more destinations than a small fanout buffer can provide. Its 1:22 differential arrangement distributes one source to 22 HSTL outputs while operating from 3.3 V. Place the device near the clock source or the major branching point, use impedance-controlled differential routing, and provide the termination topology specified by the manufacturer. The principal benefit is reduced clock-tree complexity, although output loading must remain balanced to preserve the device’s specified timing performance.
おすすめ
Networking Equipment Backplane
In networking equipment, one clock reference may serve numerous line cards, serializers, or interface controllers. The SY89823LHI’s 22 differential outputs and 500 MHz maximum operating frequency make it applicable to centralized backplane clock distribution where board losses would make a single long source-to-destination route impractical. The 1.5 V HSTL interface should be matched to every receiver, and the design should preserve controlled impedance across connectors and layer transitions. Validate loss, jitter, and skew at the highest supported line rate rather than assuming nominal fanout performance applies after routing.
おすすめ
FPGA and Processor Clock Trees
The SY89823LHI can serve as a fanout stage in an FPGA or processor clock tree when many high-speed domains need the same reference. Its 1:22 differential output count allows a designer to replace a collection of smaller buffer branches, while the 500 MHz rating supports demanding fabric, serializer, and memory-interface clocking. Each branch must retain matched differential geometry and appropriate receiver termination. Because distribution delay can differ among branches, include source-to-destination timing and external reference-clock uncertainty in the system-level budget.
おすすめ
High-Speed Test Equipment
The SY89823LHI fits high-speed test systems that must deliver a common differential clock to multiple acquisition, pattern-generation, or instrumentation channels. Twenty-two outputs reduce the need for repeated fanout stages and help keep channel organization consistent at rates up to 500 MHz. The exposed-pad TQFP package must be connected according to the manufacturer layout guidance and tied to a thermally capable plane. Probe, cable, and fixture transitions can dominate the channel budget, so validate the complete fixture rather than relying only on the bare-device specification.
おすすめ
High-Speed Serial Interface Subsystems
The SY89823LHI can distribute a differential reference clock among serializers, deserializers, retimers, and supporting logic within a high-speed serial subsystem. A 1:22 differential fanout offers a practical way to coordinate multiple lanes while retaining one common timing reference. At 500 MHz, the clock’s quality is only as good as the implemented network, so keep pairs tightly coupled, avoid unnecessary stubs, and terminate unused or receiver inputs as directed. Confirm lane-to-lane skew and reference-clock jitter at the system level.
おすすめ
Industrial Data Acquisition Systems
An industrial acquisition system can use the SY89823LHI to distribute one differential clock to multiple converters, processing channels, or communication blocks. The 22-output fanout reduces repeated buffering and provides a consistent clock reference across a densely populated board. The 3.3 V supply and 500 MHz capability support high-rate data paths, but industrial temperature and EMC requirements must be checked against the complete device rating. Add filtering and termination only where supported by the clock architecture, and verify performance over the required temperature range.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: SY89823LHI — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 |
|---|---|
| Brand | Microchip Technology |
| Package | 64-pin TQFP with exposed pad |
| Supply Voltage | 3.3 V |
| Maximum Clock Frequency | 500 MHz |
| Fanout Ratio | 1:22 differential |
| Differential Output Count | 22 outputs |
| Logic Standard | Differential HSTL |
| HSTL Output Voltage | 1.5 V |
| Device Functions | Bus clock driver, fanout buffer and translator |
主な差別化要因
- Wide differential fanout from one clock source (vs Lower-fanout SY89823-family clock buffers)
- High operating frequency for low-voltage differential clocking (vs Lower-frequency single-ended fanout buffers)
- Consolidates driver, fanout, and translation functions (vs Discrete buffer plus level-translation approaches)
設計ノート
Route every differential clock pair as a tightly coupled impedance-controlled pair with a continuous reference plane. At 500 MHz, even short unmatched stubs can create reflections that degrade clock quality. Keep layer changes and test pads minimal, provide vias symmetrically where transitions are unavoidable, and use the package pin assignments in the manufacturer datasheet when defining the escape routing. Verify the final differential impedance against the PCB stack-up rather than relying on a nominal 100 ohm target without calculation.
Implement the manufacturer-recommended source and load termination for every active output and do not leave unused differential outputs floating without checking their recommended state. Termination, receiver input capacitance, trace length, and connector loading all affect edge rate and channel-to-channel skew. Because the device provides 22 outputs, use matched routing and equivalent loading where possible so one destination does not create a materially different edge condition from the others.
Connect the exposed pad to the plane specified in the manufacturer datasheet and provide multiple thermal vias where the PCB construction permits. Estimated: junction-temperature rise depends on actual dissipation, exposed-pad copper area, via count, board construction, and airflow, so calculate it with the completed board geometry. Confirm that every clock branch remains within the device’s operating-temperature limits at the highest clock activity and worst-case supply condition.
Place low-inductance bypass capacitors close to the device’s supply and ground pins, and maintain a low-impedance distribution path from the 3.3 V source. High-frequency clock current can couple into an imperfect supply network even though HSTL output voltage is 1.5 V. Use multiple connection points where the footprint permits, avoid long current loops, and evaluate the supply ripple and clock jitter together before treating the power rail as adequate.
コンプライアンス情報
Compliance declarations and qualification status were not identified in the retrieved device listings. Confirm them against the manufacturer product documentation before production release.