Microchip Technology

SY89823LHI - 500MHz 1:22 HSTL Clock Buffer | Microchip

MPN: SY89823LHI
3.3 V Vdss 64-pin TQFP with exposed pad Package 500 MHz Speed
MOQ: 1 |

SY89823LHI Ringkasan

The Microchip Technology SY89823LHI is a 3.3 V, 500 MHz, 1:22 differential HSTL fanout buffer and translator housed in a 64-pin TQFP package with an exposed pad. It accepts one differential clock source and provides 22 differential outputs, giving a 1:22 fanout ratio for high-speed clock distribution. Its 1.5 V HSTL signaling supports modern processor, communications, and networking systems in which low-voltage differential clocking is required.

A high-speed differential clock buffer is a clock and timing IC that reproduces a differential clock across multiple outputs while preserving signal integrity, edge alignment, and source impedance. In the broader semiconductor hierarchy, the SY89823LHI belongs to the clock-buffer and translator class within clock and timing integrated circuits. Its fanout function reduces the number of separate clock sources required by a multi-channel or multi-board system.

The headline operating specifications are a 3.3 V supply, operation up to 500 MHz, a 1:22 differential fanout ratio, and 1.5 V HSTL output signaling. The 64-pin TQFP exposed-pad package provides the physical interface for the input, 22 differential output channels, power connections, and control or configuration functions defined by the manufacturer. Its principal engineering benefit is consolidated high-speed clock distribution, reducing routing complexity when many destinations require the same differential clock.

At the circuit level, the device separates clock generation from clock distribution. A low-jitter source can feed the differential input, while the SY89823LHI supplies matched output branches for downstream circuits. Maintaining controlled impedance, short trace lengths, continuous return paths, and appropriate termination is essential when routing 500 MHz differential signals. The exposed thermal pad should be connected to the supply or ground plane as directed in the manufacturer datasheet and evaluated against the system thermal budget.

Typical design uses include processor and communications clock distribution, networking-equipment backplanes, high-speed serial-interface subsystems, FPGA clock trees, and multi-channel test equipment. The part is especially relevant where one differential clock must reach many receiving circuits and cable or board losses make local regeneration preferable to long point-to-point distribution. The system designer must also verify timing budget, return loss, channel skew, and power-supply behavior for the completed board.

A critical design consideration is that a 1:22 fanout does not eliminate endpoint-specific loading or trace differences. Each output should have a controlled termination and matched routing environment, while unused channels should be handled according to the manufacturer’s recommended termination scheme. Power and ground planes must provide low-impedance paths at 500 MHz, and bypass connections should be placed close to the supply pins to limit supply-noise coupling into the clock network.

This product page consolidates the device identification, electrical characteristics, application guidance, and engineering trade-offs needed to plan a clock-distribution design. It also separates verified device facts from parameters that must be confirmed in the manufacturer datasheet, helping engineers assess fit without relying on a simple distributor listing.

Pilihan pengganti yang segera untuk SY89823LHI — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

SY89823LHI-TR

✅ Masuk Drop-In
📦 TQFP-64
Tape-and-reel ordering suffix; electrical ratings, pinout, 500 MHz operation, and 1:22 differential HSTL function are unchanged, subject to confirmation against the manufacturer ordering table.

📋 Alternatif rujukan (tidak dalam katalog)

SY89823LHI Spesifikasi

Tegangan Pemberi Arus 3.3 V
Frekuensi Klock Maksimum 500 MHz
Fanout Ratio 1:22 differential
Number of Differential Outputs 22
Logic Standard Differential HSTL
HSTL Output Voltage 1.5 V
Device Type High-performance bus clock driver, fanout buffer and translator
Kemasan 64-pin TQFP with exposed pad
Kiraan Pin 64 pins
Jenis Pemasangan Surface mount

Panduan Konfigurasi Pin SY89823LHI 64-pin tqfp with exposed pad

Konfigurasi pin untuk SY89823LHI (64-pin tqfp with exposed pad pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.

Garis bentuk pengecah pakai 64-pin tqfp with exposed pad untuk SY89823LHI

Tiada data garisan pin yang diperoleh untuk SY89823LHI.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

SY89823LHI patut untuk 6 aplikasis: Communications Clock Distribution, Networking Equipment Backplane, FPGA and Processor Clock Trees, High-Speed Test Equipment, High-Speed Serial Interface Subsystems, Industrial Data Acquisition Systems.

🌐

Communications Clock Distribution

The SY89823LHI is suitable for centralizing a 500 MHz differential clock across a communications subsystem that needs more destinations than a small fanout buffer can provide. Its 1:22 differential arrangement distributes one source to 22 HSTL outputs while operating from 3.3 V. Place the device near the clock source or the major branching point, use impedance-controlled differential routing, and provide the termination topology specified by the manufacturer. The principal benefit is reduced clock-tree complexity, although output loading must remain balanced to preserve the device’s specified timing performance.

🌐

Networking Equipment Backplane

In networking equipment, one clock reference may serve numerous line cards, serializers, or interface controllers. The SY89823LHI’s 22 differential outputs and 500 MHz maximum operating frequency make it applicable to centralized backplane clock distribution where board losses would make a single long source-to-destination route impractical. The 1.5 V HSTL interface should be matched to every receiver, and the design should preserve controlled impedance across connectors and layer transitions. Validate loss, jitter, and skew at the highest supported line rate rather than assuming nominal fanout performance applies after routing.

🖥️

FPGA and Processor Clock Trees

The SY89823LHI can serve as a fanout stage in an FPGA or processor clock tree when many high-speed domains need the same reference. Its 1:22 differential output count allows a designer to replace a collection of smaller buffer branches, while the 500 MHz rating supports demanding fabric, serializer, and memory-interface clocking. Each branch must retain matched differential geometry and appropriate receiver termination. Because distribution delay can differ among branches, include source-to-destination timing and external reference-clock uncertainty in the system-level budget.

🔧

High-Speed Test Equipment

The SY89823LHI fits high-speed test systems that must deliver a common differential clock to multiple acquisition, pattern-generation, or instrumentation channels. Twenty-two outputs reduce the need for repeated fanout stages and help keep channel organization consistent at rates up to 500 MHz. The exposed-pad TQFP package must be connected according to the manufacturer layout guidance and tied to a thermally capable plane. Probe, cable, and fixture transitions can dominate the channel budget, so validate the complete fixture rather than relying only on the bare-device specification.

⚡

High-Speed Serial Interface Subsystems

The SY89823LHI can distribute a differential reference clock among serializers, deserializers, retimers, and supporting logic within a high-speed serial subsystem. A 1:22 differential fanout offers a practical way to coordinate multiple lanes while retaining one common timing reference. At 500 MHz, the clock’s quality is only as good as the implemented network, so keep pairs tightly coupled, avoid unnecessary stubs, and terminate unused or receiver inputs as directed. Confirm lane-to-lane skew and reference-clock jitter at the system level.

🏭

Industrial Data Acquisition Systems

An industrial acquisition system can use the SY89823LHI to distribute one differential clock to multiple converters, processing channels, or communication blocks. The 22-output fanout reduces repeated buffering and provides a consistent clock reference across a densely populated board. The 3.3 V supply and 500 MHz capability support high-rate data paths, but industrial temperature and EMC requirements must be checked against the complete device rating. Add filtering and termination only where supported by the clock architecture, and verify performance over the required temperature range.

What is the SY89823LHI clock buffer used for?
The SY89823LHI is a high-performance differential bus clock driver used to distribute one clock source to 22 differential outputs. According to the Micrel Semiconductor manufacturer datasheet, the device operates from a 3.3 V supply, supports frequencies up to 500 MHz, and uses 1.5 V differential HSTL signaling. It is suitable for systems that need centralized high-speed clock fanout across multiple communications, processing, networking, or test subsystems.
What are the key specifications of SY89823LHI that engineers should know?
The key SY89823LHI specifications are a 3.3 V supply, operation up to 500 MHz, a 1:22 differential fanout arrangement, 22 HSTL output channels, and a 64-pin TQFP package with an exposed pad. According to the Micrel Semiconductor manufacturer datasheet, the device combines clock-buffer, fanout, and translator functions. These parameters make it most relevant to boards requiring one differential source to feed numerous high-speed destinations.
Where can I download the SY89823LHI datasheet PDF?
The SY89823LHI datasheet PDF can be opened through the Micrel Semiconductor document link listed on this page. The document identifies the part as a 3.3 V, 500 MHz, 1:22 differential HSTL fanout buffer and translator in a 64-TQFP exposed-pad package. For layout and signal-integrity work, use the manufacturer datasheet for the authoritative pin-description table, recommended terminations, operating limits, and exposed-pad connection instructions.
Where can I find the SY89823LHI pinout?
The SY89823LHI pinout is identified in the manufacturer datasheet under the 64-pin TQFP package information and pin-description table. The component has 64 pins, including differential clock outputs and supply or ground connections defined by Micrel. Because an exact public pin-description table was not included in the retrieved listing text, use the datasheet rather than assigning PCB functions from package position or signal type alone.
What is the difference between the SY89823LHI and SY89823LHI-TR?
The SY89823LHI and SY89823LHI-TR identify the same Micrel clock-buffer device family, with the -TR designation associated with a tape-and-reel ordering option. The underlying electrical function remains a 3.3 V, 500 MHz, 1:22 differential HSTL fanout buffer and translator in a 64-pin TQFP exposed-pad package. The -TR variant should not be treated as a distinct drop-in alternative because its distinguishing value is shipping format rather than electrical or pin-level differentiation.
Is the SY89823LHI suitable for a 500 MHz differential clock network?
The SY89823LHI is rated for operation up to 500 MHz and is specifically described as a differential HSTL clock fanout buffer and translator. According to the Micrel Semiconductor manufacturer datasheet, its architecture supports one differential source and 22 differential outputs. Suitability for a complete design still depends on source jitter, output skew, trace loss, termination, return paths, connector transitions, and receiver capability at the intended operating frequency.
How should I route differential HSTL clock outputs at 500 MHz?
Route the SY89823LHI differential outputs as short, impedance-controlled pairs with continuous ground references and matched termination. At 500 MHz, vias, layer transitions, connector launches, and unequal trace lengths can degrade the differential signal even when the logic family itself supports the frequency. Keep bypass capacitors close to the device, preserve the manufacturer-recommended return and termination topology, and verify output timing and channel-to-channel skew on the completed board.
When should I choose the SY89823LHI instead of a lower fanout clock buffer?
Choose the SY89823LHI when one 3.3 V differential clock must be distributed to as many as 22 destinations at rates up to 500 MHz. Its 1:22 fanout consolidates clock routing and can reduce the number of separate buffer stages required. A lower-fanout device may be preferable when there are fewer receivers, tighter channel-skew requirements across very different loads, lower operating frequency, lower supply current, or a smaller package is more important than output count.
What is the best drop-in replacement for SY89823LHI?
No independently verified drop-in replacement for the SY89823LHI was identified in the retrieved cross-reference results. A genuine replacement would need the same 64-pin TQFP exposed-pad footprint, pin-to-pin assignments, 3.3 V operation, 1:22 differential fanout, 500 MHz capability, and compatible HSTL termination. Until all of those conditions are confirmed, treat any similarly described clock buffer as a redesign candidate rather than an automatic substitution.
Can another 1:22 HSTL clock buffer replace the SY89823LHI?
A 1:22 HSTL clock buffer can replace the SY89823LHI only after its package, pinout, supply voltage, output voltage, enable architecture, termination requirements, and timing characteristics are confirmed equivalent. Matching the 500 MHz headline frequency and 1:22 fanout ratio alone is insufficient because pin assignment and input or output compatibility determine whether a replacement is truly drop-in. Use the manufacturer pin and application tables to complete that verification.
Where can I buy SY89823LHI online?
Use the Request a Quote form on this page to request the current SY89823LHI price, inventory position, minimum order quantity, and lead time. The part is a 3.3 V, 500 MHz, 1:22 differential HSTL fanout buffer and translator in a 64-pin TQFP exposed-pad package. A written quote is the appropriate way to confirm exact suffix, packaging, authentication requirements, and current commercial availability.
What is the price of SY89823LHI?
The current SY89823LHI price is obtained through the Request a Quote form on this page. Pricing can vary with exact ordering suffix, reel or tube packaging, quantity, required traceability, and market conditions. The technical identity used for the quotation is the 3.3 V, 500 MHz, 1:22 differential HSTL fanout buffer and translator in a 64-pin TQFP exposed-pad package.
What is the lead time for SY89823LHI?
The current SY89823LHI lead time and minimum order quantity should be requested through the Request a Quote form on this page. Lead time can change with the exact ordering package and order quantity, so an up-to-date quotation is more useful than a generic inventory estimate. Include the required package format, production quantity, date code policy, and any traceability requirements when submitting the request.
Is SY89823LHI in stock?
Current SY89823LHI inventory status should be confirmed through the Request a Quote form on this page. Stock figures can vary by exact suffix and authorized channel, while large production orders may be scheduled rather than drawn from spot inventory. Provide your required quantity and packaging preference with the request so the supplier can confirm available inventory and the applicable lead time.
Is SY89823LHI the same as other 1:22 differential clock drivers?
The SY89823LHI is not automatically interchangeable with another 1:22 differential clock driver, even if the frequency and fanout ratio match. According to the Micrel Semiconductor manufacturer datasheet, the defining electrical identity includes 3.3 V operation, 1.5 V differential HSTL signaling, up to 500 MHz operation, and a 64-pin TQFP exposed-pad implementation. Pin compatibility, termination, timing, and control logic must also match.
What design constraints matter most when using the SY89823LHI exposed-pad package?
The exposed pad on the SY89823LHI’s 64-pin TQFP package must be connected as specified in the manufacturer datasheet and placed on a suitable ground or supply plane. Estimated: thermal performance depends on the exposed-pad copper area, board construction, airflow, and total device dissipation, so calculate the junction-temperature rise with the exact PCB geometry rather than relying only on the package pin count. Maintain short thermal-via connections and low-impedance power distribution.

Data referensi kejuruteraan untuk SY89823LHI — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose the SY89823LHI when a 3.3 V system needs one differential clock source distributed to as many as 22 destinations at frequencies up to 500 MHz. Its 1:22 differential fanout and 1.5 V HSTL outputs are particularly useful in communications, networking, processor, FPGA, and test-equipment clock trees where a large number of branches would otherwise require multiple buffer stages. Consider a lower-fanout buffer when there are fewer receivers, when channel loading varies substantially, or when lower power and smaller package size matter more than output count. Do not substitute a superficially similar 1:22 driver unless its 64-pin TQFP exposed-pad footprint, exact pin assignments, HSTL levels, timing, and termination requirements are confirmed equivalent.

Perbandingan dengan Gantian

Parametr Produk Ini
Brand Microchip Technology
Package 64-pin TQFP with exposed pad
Supply Voltage 3.3 V
Maximum Clock Frequency 500 MHz
Fanout Ratio 1:22 differential
Differential Output Count 22 outputs
Logic Standard Differential HSTL
HSTL Output Voltage 1.5 V
Device Functions Bus clock driver, fanout buffer and translator

Penyeberangsung Jelas

  • Wide differential fanout from one clock source (vsLower-fanout SY89823-family clock buffers)
  • High operating frequency for low-voltage differential clocking (vsLower-frequency single-ended fanout buffers)
  • Consolidates driver, fanout, and translation functions (vsDiscrete buffer plus level-translation approaches)

Catatan Desain

Route every differential clock pair as a tightly coupled impedance-controlled pair with a continuous reference plane. At 500 MHz, even short unmatched stubs can create reflections that degrade clock quality. Keep layer changes and test pads minimal, provide vias symmetrically where transitions are unavoidable, and use the package pin assignments in the manufacturer datasheet when defining the escape routing. Verify the final differential impedance against the PCB stack-up rather than relying on a nominal 100 ohm target without calculation.

Implement the manufacturer-recommended source and load termination for every active output and do not leave unused differential outputs floating without checking their recommended state. Termination, receiver input capacitance, trace length, and connector loading all affect edge rate and channel-to-channel skew. Because the device provides 22 outputs, use matched routing and equivalent loading where possible so one destination does not create a materially different edge condition from the others.

Connect the exposed pad to the plane specified in the manufacturer datasheet and provide multiple thermal vias where the PCB construction permits. Estimated: junction-temperature rise depends on actual dissipation, exposed-pad copper area, via count, board construction, and airflow, so calculate it with the completed board geometry. Confirm that every clock branch remains within the device’s operating-temperature limits at the highest clock activity and worst-case supply condition.

Place low-inductance bypass capacitors close to the device’s supply and ground pins, and maintain a low-impedance distribution path from the 3.3 V source. High-frequency clock current can couple into an imperfect supply network even though HSTL output voltage is 1.5 V. Use multiple connection points where the footprint permits, avoid long current loops, and evaluate the supply ripple and clock jitter together before treating the power rail as adequate.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

Compliance declarations and qualification status were not identified in the retrieved device listings. Confirm them against the manufacturer product documentation before production release.

Data disahkan pada: 2026-11-10 — data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART

Pencarian Berhubungan

SY89823LHI datasheet SY89823LHI pinout SY89823LHI datasheet pdf SY89823LHI equivalent SY89823LHI replacement SY89823LHI drop-in replacement SY89823LHI price SY89823LHI stock Microchip SY89823LHI SY89823LHI 500MHz clock buffer SY89823LHI 1:22 fanout SY89823LHI 64-TQFP pinout SY89823LHI differential HSTL SY89823LHI networking clock distribution SY89823LHI vs SY89831UMG

Komponen dan Tanda berkaitan

Microchip Technology Micrel Semiconductor SY89823LHI SY89831UMG SY89872UMG clock buffer clock driver bus clock driver fanout buffer logic translator clock and timing integrated circuit differential HSTL 1:22 differential fanout 3.3 V supply 1.5 V HSTL 500 MHz clock 64-pin TQFP exposed pad surface-mount package differential clock routing controlled impedance clock jitter output skew networking equipment FPGA clock tree
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ