Texas Instruments

TAS5001PFBR - 2-Channel Digital Audio PWM Processor | Texas Instruments

部品番号: TAS5001PFBR ✓ 生産中
3.3 V PWM output Vdss 48-pin TQFP, 7 x 7 mm Package
MOQ: 1 |

TAS5001PFBR 概要

The Texas Instruments TAS5001PFBR is a 2-channel digital audio PWM processor in a 48-pin TQFP (7 x 7 mm) package. It accepts a serial PCM digital-audio stream and converts it into a 3.3 V PWM audio stream for a true digital audio amplifier system. The device provides 96 dB dynamic range, while a complete TAS5001-based system is measured at 93 dB dynamic range. Its stated THD+N is 0.08% at 1 kHz.

A digital audio PWM processor is a specialized signal-processing IC that bridges a digital audio source and a class-D-style power-output stage. It performs digital volume control, gain management, signal conditioning, and PCM-to-PWM conversion inside the amplification signal chain. In the true digital audio amplifier architecture described by Texas Instruments, the TAS5001 works with a separate PWM power-output device such as the TAS5100.

The principal system benefits are precise digital gain control, high digital dynamic range, and reproduction of PCM source material without relying on a conventional analog voltage-gain stage. The 3.3 V PWM output interface is intended for an external power stage, allowing power-amplifier topology and speaker loading to remain separate from the digital processing function. The 48-pin TQFP package provides adequate routing capacity for digital interfaces, power connections, ground returns, and configuration pins.

The verified part description identifies the TAS5001 as a true digital audio amplifier digital audio PWM processor rather than a complete power amplifier. Consequently, an external PWM power-output device and speaker interface are required. System designers should evaluate the complete TAS5001 and TAS5100 signal path, including digital-clock behavior, power sequencing, output filtering, and thermal performance of the power stage.

Typical uses include compact digital-audio speakers, multimedia speaker systems, powered speaker modules, soundbar amplification subsystems, and portable consumer-audio products. The processor is most appropriate when the product accepts digital PCM audio and benefits from digital attenuation or system-level gain management. It is less suitable for a design that expects the IC itself to drive a speaker directly.

When laying out the board, place decoupling capacitors close to the supply pins, route the serial digital-audio and clock signals away from the PWM power-stage traces, and keep the ground return from the processor isolated from high-current speaker currents. Confirm pin functions, clock requirements, configuration values, and supported sample rates against the manufacturer datasheet before releasing the PCB.

This page consolidates the verified device description, technical performance figures, sourcing information, and practical design guidance into one engineering reference. It also identifies documented replacement candidates and distinguishes them from merely similar audio processors so that footprint and functional compatibility can be assessed before a design change.

ドロップイン代替品: TAS5001PFBR — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。

このシリーズのバリエーション

同一シリーズでドロップイン互換のモデル: TAS5001PFBR (同一形状・フットプリント) — 相違点: Package.

Texas Instruments
Package: 48-TQFP (7x7 mm)
比較対象 TAS5001PFBR →

TAS5001IPFB

✅ ドロップイン
Texas Instruments
📦 48-TQFP (7x7)
Digital audio PWM processor · 2 channels · 96 dB · 93 dB at speaker terminals · 0.08% at 1 kHz · Serial PCM digital audio stream · 3.3 V · 48-TQFP, 7 mm x 7 mm

価格はお問い合わせください

データシートを見る →

TAS5001PFBG4

✅ ドロップイン
📦 48-TQFP (7x7)
Same TAS5001PFB device and 48-TQFP pinout; G4 ordering suffix identifies a different catalog or qualification variant

📋 参考代替品(カタログ未掲載)

TAS5001PFBR 最大定格&電気的特性

Device Type Digital audio PWM processor
Channel Count 2 channels
Architecture True digital audio amplifier
Input Signal Format Serial PCM digital audio
Output Signal Format 3.3 V PWM audio stream
Dynamic Range, Device 96 dB
Dynamic Range, TAS5001 and TAS5100 System 93 dB measured at speaker terminals
THD+N 0.08% at 1 kHz
パッケージ 48-pin TQFP, 7 x 7 mm
実装タイプ Surface mount
出力電圧 3.3 V PWM output
External Power Stage Required Yes, PWM power-output device required

TAS5001PFBR 48-pin tqfp, 7 x 7 mm ピン配置ガイド

TAS5001PFBR (48-pin tqfp, 7 x 7 mm パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。

TAS5001PFBR の 48-pin tqfp, 7 x 7 mm パッケージピン配置図

詳細なピン配置データはありません: TAS5001PFBR.

詳細は データシート をご参照ください。

主な用途

TAS5001PFBR の用途: 6 件s: Digital Powered Speaker Module, Multimedia Speaker System, Soundbar Amplification Subsystem, Portable Consumer Audio Product, Network Audio Terminal, Digital Audio Evaluation Platform.

🔊

Digital Powered Speaker Module

The TAS5001PFBR fits a powered speaker module that receives serial PCM audio and requires digital gain management before a separate PWM power stage. Its 2-channel architecture supports stereo operation, while the 96 dB device dynamic range provides ample headroom for digital attenuation and signal conditioning. The processor produces a 3.3 V PWM stream rather than driving a loudspeaker directly, so the design must include a compatible external power-output device, an LC speaker filter, and a correctly sized power supply. Keep the processor ground return separate from the high-current speaker return to prevent PWM switching noise from coupling into the digital audio path.

🖥️

Multimedia Speaker System

A multimedia speaker system can use the TAS5001PFBR to accept PCM audio from a host processor and apply digital volume and gain control before power amplification. The 48-pin TQFP package provides the routing capacity needed for two-channel digital audio, clocking, configuration, supplies, and PWM outputs. The documented 0.08% THD+N at 1 kHz makes the device relevant to compact stereo products where audible distortion matters. Designers should budget board area for decoupling and the external PWM stage, and should verify the supported sample rates and clock configuration against the manufacturer datasheet.

📺

Soundbar Amplification Subsystem

The TAS5001PFBR is suitable for an audio-processing subsection of a soundbar when the subsystem receives digital PCM audio and delegates loudspeaker drive to an external PWM output device. Its 2-channel organization aligns with left and right signal paths, and the 96 dB device dynamic range supports precise digital attenuation. The key implementation benefit is that volume adjustment occurs in the digital domain instead of through a conventional analog gain stage. In a soundbar, keep PWM power routing and speaker currents away from the serial audio nets, use a solid ground-plane strategy, and verify thermal performance in the external power amplifier rather than the processor package.

📱

Portable Consumer Audio Product

In a portable consumer-audio product, the TAS5001PFBR can process digital program material while leaving loudspeaker drive to an efficient external PWM stage. Digital gain control helps maintain consistent output levels across source conditions, and the 2-channel format supports stereo playback from one processor. Power-system design remains critical because the processor is only one element of the amplifier: supply voltage, quiescent demand, sequencing, and thermal limits must be coordinated with the power-output device. Verify battery-voltage behavior, startup sequencing, and clock stability in the manufacturer datasheet before production integration.

🌐

Network Audio Terminal

The TAS5001PFBR can serve as the final digital audio processing element in a network audio terminal once a host has decoded the digital stream to PCM. Its serial PCM input and 3.3 V PWM output simplify the boundary between digital playback logic and the power-amplification section, while 96 dB device dynamic range supports high-quality playback. The processor does not perform network decoding, so the source architecture must provide a valid PCM clock and word stream. Route these signals as controlled-length digital nets, provide local decoupling at the supply pins, and test the complete system for PWM-related radiated emissions.

🔧

Digital Audio Evaluation Platform

The TAS5001PFBR is useful on an audio evaluation platform because it exposes a complete digital-processing path before power amplification. Engineers can evaluate channel routing, digital gain, 3.3 V PWM waveform behavior, and system distortion using the published 0.08% THD+N at 1 kHz as a reference point. The 48-TQFP package requires a fine-pitch assembly or a suitable carrier board, making prototype layout and exposed-pin soldering an important part of the evaluation plan. A companion power stage such as the TAS5100 permits evaluation of the full true digital audio amplifier system and measurement at the speaker terminals.

おすすめ製品の概要

TAS5100 External PWM power-output device for a TAS5001 reference system 使用用途: Digital Powered Speaker Module, Multimedia Speaker System, Soundbar Amplification Subsystem, Portable Consumer Audio Product, Network Audio Terminal, Digital Audio Evaluation Platform
What is the TAS5001PFBR used for?
The TAS5001PFBR is a 2-channel digital audio PWM processor that converts a serial PCM audio stream into a 3.3 V PWM output. It is intended for a true digital audio amplifier system with an external PWM power-output device. According to the Texas Instruments device description, the processor provides digital signal conditioning and 96 dB device dynamic range rather than directly driving a loudspeaker.
Does TAS5001PFBR directly drive a speaker?
No. The TAS5001PFBR is a digital audio PWM processor, not a complete speaker-power amplifier. Its 3.3 V PWM output must feed a suitable external PWM power stage before driving a speaker. The manufacturer describes a TAS5001 and TAS5100 system that achieves 93 dB dynamic range measured at the speaker terminals, confirming that the power-output stage is a separate part of the signal chain.
What is the dynamic range of TAS5001PFBR?
The TAS5001 device is specified at 96 dB dynamic range. Texas Instruments also reports 93 dB dynamic range for a complete TAS5001 and TAS5100 system measured at the speaker terminals. The difference reflects the complete amplifier chain rather than the processor alone. The published distortion figure for this device is 0.08% THD+N at 1 kHz.
What package does TAS5001PFBR use?
The TAS5001PFBR uses a 48-pin TQFP package measuring 7 x 7 mm. The surface-mount package is identified consistently by Texas Instruments listings and distributor product pages. Use the manufacturer pin-description table when assigning PCB nets, because the device requires digital audio, clock, control, power, ground, and PWM-output connections across 48 terminals.
Where can I download the TAS5001PFBR datasheet PDF?
The manufacturer datasheet is available through the Texas Instruments TAS5001 documentation and the archived manufacturer PDF on Datasheets.com. The TAS5001PFBR is also covered by the joint TAS5001 and TAS5100 application material. Use the pin-description and typical-application sections to confirm clocking, configuration, supply sequencing, and output-network requirements before layout release.
Where can I find the TAS5001PFBR pinout?
The authoritative TAS5001PFBR pin assignment is in the pin-description table of the manufacturer datasheet. The part is a 48-pin TQFP, so the assignment covers all 48 package terminals rather than only the signal pins highlighted in a simplified application diagram. Use that table to map every supply, ground, digital-audio, clock, control, and PWM-output terminal on the PCB.
What are the key specifications of TAS5001PFBR that engineers should know?
The core TAS5001PFBR specifications are 2 audio channels, 96 dB device dynamic range, 0.08% THD+N at 1 kHz, a 3.3 V PWM output, and a 48-pin 7 x 7 mm TQFP package. The processor accepts serial PCM audio and requires an external PWM power-output device. A complete TAS5001 and TAS5100 system is reported at 93 dB dynamic range measured at the speaker terminals.
Can TAS5001IPFB replace TAS5001PFBR?
Yes. Cross-reference information describes the Texas Instruments TAS5001IPFB as a complete replacement for the TAS5001PFBR, with matching terminals, package, and principal functional characteristics. It is therefore the closest documented same-brand drop-in candidate. Confirm ordering details, temperature grade, and configuration defaults in the manufacturer datasheet before committing it to a production design.
What is the best drop-in replacement for TAS5001PFBR?
The TAS5001IPFB is the best documented drop-in replacement for the TAS5001PFBR because a component comparison identifies it as a complete replacement with consistent terminals, package, and main performance characteristics. No independently verified cross-brand equivalent met the drop-in requirement. The TAS5010PFB and TAS5010IPFB appear in comparisons but should not be treated as drop-in replacements without a complete pin and functional review.
What is the difference between TAS5001PFBR and TAS5010PFB?
Both devices are compared as Texas Instruments audio-processing ICs, but the available comparison does not establish that they are pin-to-pin replacements. The TAS5001 is identified as a 2-channel digital audio PWM processor producing a 3.3 V PWM stream, while the TAS5010 has a different device designation. Do not assume drop-in compatibility; check the pin-description, clocking, and signal-processing blocks for both parts.
Is TAS5001PFBR suitable for a powered speaker module?
The TAS5001PFBR is suitable for the digital-processing section of a powered speaker module that accepts PCM audio and uses an external PWM power stage. Its 96 dB device dynamic range and 0.08% THD+N at 1 kHz support high-fidelity audio designs. The system designer must still add a power-output IC, speaker filter, supply, and output-network components.
When should I choose TAS5001PFBR instead of a conventional audio amplifier?
Choose the TAS5001PFBR when the source is digital PCM audio and the design benefits from digital gain control, a 96 dB processor dynamic range, and a true digital audio amplifier architecture. A conventional analog amplifier is simpler when only analog audio is available. The TAS5001 also adds system complexity because it requires a compatible external PWM power stage and carefully isolated signal routing.
Is there a Texas Instruments equivalent for TAS5001PFBR?
The closest Texas Instruments equivalent is the TAS5001IPFB, which is explicitly described as a complete replacement with matching terminals and package. It preserves the principal performance and functional characteristics of the TAS5001PFBR. The TAS5001PFBG4 is another same-family catalog entry, but its orderable suffix and qualification details should be checked before treating it as an interchangeable production choice.
Where can I buy TAS5001PFBR online?
The TAS5001PFBR can be requested through the Request a Quote form on this page, where the exact MPN, target quantity, and delivery requirements can be submitted. Manufacturer and distributor listings also identify the 48-TQFP (7 x 7 mm) part. Use the quote form to confirm current unit availability, scheduled delivery, and lot traceability rather than relying on a static listing price.
What is the lead time for TAS5001PFBR?
Lead time depends on current inventory, order quantity, and the manufacturing status of the exact suffix. One distributor listing describes immediate shipment capability for the TAS5001PFBR, but inventory can change rapidly. Submit the required quantity and target schedule through the Request a Quote form on this page to obtain a current, quantity-specific delivery commitment.

エンジニアリング参考データ: TAS5001PFBR — 比較、設計ガイダンス、コンプライアンス情報。

選定ガイド

Choose the TAS5001PFBR when a product accepts serial PCM audio and needs a dedicated digital-processing stage ahead of a PWM power amplifier. Its 2-channel architecture, 96 dB device dynamic range, 0.08% THD+N at 1 kHz, and 3.3 V PWM output make it suitable for powered speakers, multimedia systems, and other true-digital-amplifier products. Select TAS5001IPFB when it is the preferred orderable form but identical function and footprint are required; it is the closest documented drop-in alternative. TAS5001PFBG4 is another same-family catalog entry, but qualification and ordering details must be checked before use. Do not select the TAS5010 family solely for package similarity because verified cross-reference information does not establish drop-in compatibility. If your design has analog input only or does not include an external PWM power stage, a conventional integrated audio amplifier may be simpler.

代替品との比較

パラメータ この製品 TAS5001IPFB TAS5001PFBG4
Brand Texas Instruments Texas Instruments Texas Instruments
Package 48-TQFP (7x7) 48-TQFP (7x7) - same 48-TQFP (7x7) - same
Device Type 2-channel digital audio PWM processor Digital audio PWM processor TAS5001PFB family device
Output Signal 3.3 V PWM audio stream 3.3 V PWM audio stream 3.3 V PWM audio stream
External Power Stage Required Required Required
Replacement Relationship Reference device Documented complete replacement Same-family catalog variant

主な差別化要因

  • Documented complete replacement (vs TAS5001IPFB)
  • Native two-channel digital audio architecture (vs TAS5001PFBG4)
  • Quantified signal performance (vs TAS5001IPFB)

設計ノート

Route the serial PCM, clock, and control signals as digital nets away from the high-current PWM and speaker paths. Place supply-decoupling capacitors at the corresponding package pins rather than at a remote power-entry point, and use a continuous ground reference for the processor while returning the external power stage's speaker current through a separate, carefully terminated path.

The TAS5001PFBR is a signal-processing IC, not a direct speaker driver. Allocate board area for a compatible PWM power-output device, its supply circuitry, and the filtered speaker output. Review every pin in the manufacturer pin-description table before final routing; a simplified system diagram may omit configuration, clock, supply, and ground terminals needed by the 48-pin TQFP.

Do not treat the TAS5010PFB or TAS5010IPFB as drop-in replacements merely because they appear in the same comparison listing. The verified cross-reference identifies TAS5001IPFB as a complete replacement. For any other substitution, verify package dimensions, pin names, clocking, configuration behavior, audio-channel mapping, and PWM-output requirements against the manufacturer documentation before layout changes are made.

コンプライアンス情報

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
鉛フリー
Unknown
ハロゲンフリー
Unknown
紛争鉱物
Unknown

No explicit environmental-compliance declarations are stated in the verified product information. This audio DSP is not an automotive-qualified device designation.

データ検証日: 2026-11-15 — データはXAIPARTの部品エンジニアリングチームによって検証・管理されています

関連検索

TAS5001PFBR datasheet TAS5001PFBR pinout TAS5001PFBR datasheet pdf Texas Instruments TAS5001PFBR TAS5001PFBR 48 TQFP TAS5001PFBR equivalent TAS5001PFBR replacement TAS5001PFBR cross reference TAS5001PFBR vs TAS5001IPFB TAS5001PFBR vs TAS5010PFB TAS5001PFBR price TAS5001PFBR stock TAS5001 digital audio PWM processor TAS5001PFBR powered speaker application TAS5001PFBR schematic

関連部品&用語

Texas Instruments TAS5001PFBR TAS5001 TAS5001IPFB TAS5001PFBG4 TAS5100 TAS5010PFB TAS5010IPFB Digital audio PWM processor True digital audio amplifier PCM PWM 3.3 V PWM output 48-pin TQFP TQFP package family Surface mount Digital signal processing Audio signal processor 96 dB dynamic range 0.08% THD+N Digital gain control Speaker power stage LC speaker filter PCM-to-PWM conversion
クイック見積RFQ
詳細をすべてご記入ください — 営業チームが24時間以内にご返信いたします
部品番号 メーカー パッケージ QTY 目標価格 小計
✓
見積を送信しました!

24時間以内にメールでご返信いたします

1
RFQ送信済み
2
見積受領
3
注文済み
4
お支払い
5
発送済み
6
配達済み
RFQの詳細を表示