TPS7133QDR - 3.3V 500mA LDO with RESET | Texas Instruments
部品番号: TPS7133QDR ✓ 生産中| 数量 | 単価 | 小計 |
|---|---|---|
| 1 | $1.25 | $1.25 |
| 10 | $1.12 | $11.20 |
| 100 | $0.94 | $94.00 |
| 500 | $0.79 | $395.00 |
| 1,000 | $0.68 | $680.00 |
TPS7133QDR 概要
An LDO regulator is a type of linear voltage regulator that maintains a stable output even when the input-output differential is very small. Unlike switching regulators, LDOs produce no switching noise, making them part of the broader power management IC (PMIC) family used to post-regulate noisy DC-DC rails and supply analog loads.
Key features include a very low dropout voltage of 47mV at 100mA load, low quiescent current of 285uA, 274uVrms output noise, and 54dB PSRR at 120Hz. The PMOS pass element replaces the conventional pnp transistor, achieving an order-of-magnitude reduction in dropout voltage and quiescent current over older LDO architectures. Protection features include over-current and over-temperature shutdown, and the device operates from -40C to +125C junction temperature with a maximum input of 10V.
The RESET output asserts low when the output falls out of regulation and includes a delay to allow processor power rails to stabilize, eliminating a separate supervisor IC in microcontroller systems.
Typical applications include battery-powered portable instruments, 3.3V microcontroller and DSP power supplies, and post-regulation of switching converter outputs where low noise and fast transient response matter.
Design tip: use a 0.1uF input bypass and at least a 10uF output capacitor with low ESR for stability, and keep the enable pin driven or tied high to avoid floating-pin leakage in always-on designs.
ドロップイン代替品: TPS7133QDR — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
クイック比較ツール — 並列比較する代替部品を選択:
TPS7133QDRG4
✅ ドロップイン📋 参考代替品（カタログ未掲載）
TPS7133QD
✅ ドロップイン📋 参考代替品（カタログ未掲載）
TPS7101QDR
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
TPS7148QDR
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
TPS7150QDR
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
TPS7333QD
⚡ 同一パッケージ ⚠️ 仕様未検証📋 参考代替品（カタログ未掲載）
TPS7133QDR 最大定格＆電気的特性
| 出力タイプ | Fixed Positive |
| 出力電圧 | 3.3 V |
| 最大出力電流 | 500 mA |
| Maximum Input Voltage | 10 V |
| ドロップアウト電圧 | 47 mV at 100 mA |
| 静止電流 | 285 uA |
| 出力ノイズ | 274 uVrms |
| PSRR | 54 dB at 120 Hz |
| 出力数 | 1 |
| Protection Features | Over Current Protection, Over Temperature Protection |
| イネーブルピン | Yes |
| Reset Output | Yes, with delay |
| 動作温度 | -40C to +125C (Tj) |
| パッケージ | SOIC-8 (D) |
| 実装タイプ | Surface Mount |
| RoHS ステータス | Compliant |
TPS7133QDR ピン構成
| ピン 1 | IN — Input supply voltage (up to 10 V) |
| ピン 2 | GND — Ground |
| ピン 3 | EN — Enable input (active high; drive or tie high for always-on) |
| ピン 4 | NC — No connect |
| ピン 5 | RESET — Reset output with delay; asserts low when output out of regulation |
| ピン 6 | NC — No connect |
| ピン 7 | OUT — Regulated 3.3 V output |
| ピン 8 | OUT — Regulated 3.3 V output |
主な用途
TPS7133QDR の用途: 6 件s: Microcontroller and DSP Power Supply, Battery-Powered Portable Instruments, Post-Regulation of DC-DC Converters, Industrial Control and Automation, Analog Sensor Signal Chains, Test and Measurement Equipment.
Microcontroller and DSP Power Supply
The TPS7133QDR's fixed 3.3V, 500mA output directly powers microcontrollers, DSPs, and low-power FPGAs. Its 47mV dropout at 100mA allows regulation from a 3.6V lithium cell or a 5V bus with minimal headroom, while the integrated delayed RESET output eliminates a separate supervisor IC by holding the processor in reset until the rail is valid. With only 285uA quiescent current and over-temperature protection, it suits both always-on and duty-cycled embedded systems in SOIC-8.
おすすめ
Battery-Powered Portable Instruments
For battery-operated equipment, the TPS7133QDR's 285uA quiescent current and very low 47mV dropout maximize usable battery capacity. Operating from inputs up to 10V, it accepts multi-cell alkaline or single-cell lithium stacks and maintains regulation deep into discharge. The enable pin allows the system MCU to shut the rail down completely, and 274uVrms output noise keeps analog front ends in portable measurement instruments clean without post-filtering.
おすすめ
Post-Regulation of DC-DC Converters
When a switching converter supplies a shared rail, the TPS7133QDR cleans it for noise-sensitive loads. Its 54dB PSRR at 120Hz attenuates low-frequency ripple while the PMOS LDO adds no switching artifacts, yielding 274uVrms output noise for analog circuits, VCOs, and precision references. Pair it after a buck converter whose output sits slightly above 3.3V; the small headroom keeps power dissipation low in the 500mA-rated SOIC-8 package.
おすすめ
Industrial Control and Automation
Industrial controllers need reliable 3.3V logic rails with supervision. The TPS7133QDR operates from -40C to +125C junction temperature, meeting harsh cabinet environments, and its over-current and over-temperature protection survive faulted field wiring. The delayed RESET output guarantees microcontrollers boot cleanly after brownouts on 5V or 9V plant supplies, and the 10V maximum input tolerates unregulated wall-adapter supplies commonly found in industrial I/O modules.
おすすめ
Analog Sensor Signal Chains
Precision sensor interfaces benefit from the TPS7133QDR's 274uVrms noise and 54dB PSRR at 120Hz, which keep the analog supply clean for amplifiers and ADC references. The low dropout supports operation directly from a 3.6V Li-SOCl2 cell common in remote sensor nodes, and the 285uA quiescent current preserves long deployment life. Use a 10uF low-ESR output capacitor to maintain stability across the full -40C to +125C range.
おすすめ
Test and Measurement Equipment
Bench instruments and modular measurement boards use the TPS7133QDR to derive quiet 3.3V rails for clocking, logic, and analog sections. The enable pin supports software-controlled power sequencing of module sections, while the RESET function reports rail validity to a system controller. With 500mA capability and low output noise, it powers oscillators, level translators, and ADC front ends without adding jitter-inducing supply noise to measurement paths.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: TPS7133QDR — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | TPS7133QDRG4 | TPS7101QDR | TPS7150QDR | TPS7333QD |
|---|---|---|---|---|---|
| Package | SOIC-8 (D) | SOIC-8 (D) - same | SOIC-8 (D) - same | SOIC-8 (D) - same | SOIC-8 (D) - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Output Voltage | 3.3 V fixed | 3.3 V fixed | Adjustable 1.2 V - 9.75 V | 5.0 V fixed | 3.3 V fixed |
| Output Current | 500 mA | 500 mA | 500 mA | 500 mA | 500 mA |
| Enable Pin | Yes | Yes | Yes | Yes | Yes |
| Reset Output | Yes, with delay | Yes, with delay | Yes, with delay | Yes, with delay | Yes, with delay |
主な差別化要因
- Integrated delayed RESET supervisor （vs TPS7101QDR)
- PMOS architecture yields ultra-low quiescent current （vs TPS7333QD)
- Only 47mV dropout at 100mA （vs TPS7150QDR)
設計ノート
Place a 0.1uF ceramic bypass capacitor within 5mm of the IN pin and a 10uF low-ESR capacitor at the OUT pin. The TPS71 family requires an output capacitor for stability; ceramic X7R dielectric is preferred. Keep the RESET pull-up resistor (10k to 100k ohm) close to the pin to avoid noise coupling into the open-drain supervisor node.
At maximum load of 500mA with a 5V input and 3.3V output, dissipation is 0.85W. The SOIC-8 (D) package theta_JA of roughly 97 C/W on a standard board would raise the junction about 82C - acceptable at 25C ambient but marginal at 70C ambient. Use a solid ground-plane copper pour under the device or lower the input voltage (e.g., post-regulate from a 3.6V buck) for high-temperature enclosures.
Do not exceed the 10V maximum input rating - unregulated wall adapters can exceed this on light load. Never leave the EN pin floating; tie it to IN for always-on operation. When substituting TPS7333QD (TPS73 family), the pinout and RESET delay differ from TPS71 - verify the datasheet pin map and RESET timing before swapping layouts.
The 274uVrms noise and 54dB PSRR figures assume the recommended output capacitor. For even lower noise on ADC reference rails, add an RC post-filter or ferrite bead; do not add large bulk capacitance beyond the datasheet-stable range without verifying phase margin on the bench with a load-step test.
コンプライアンス情報
RoHS compliant per DigiKey and JLCPCB listings. Not AEC-Q100 qualified. REACH and halogen-free status not stated in verified data.
