VSC8514XMK-13 - Quad-Port Gigabit Ethernet PHY | Microchip
部品番号: VSC8514XMK-13 ✓ 生産中VSC8514XMK-13 概要
A Gigabit Ethernet PHY is the physical-layer component that converts digital Ethernet data into signals suitable for transmission over twisted-pair cabling and performs the complementary receive function. It sits below the Ethernet MAC in the communication hierarchy: application data passes through the MAC and network processor before reaching the PHY, which provides the physical copper-port interface. A multiport PHY consolidates four Gigabit Ethernet channels in one package, reducing component count, board area, and power-management complexity compared with four discrete ports.
The VSC8514 supports 10/100/1000BASE-T operation for enterprise and carrier networks, while its QSGMII and SGMII-family connectivity allows connection to a switching or routing device. Synchronous Ethernet support and TDM backhaul capabilities make the device applicable to infrastructure equipment requiring deterministic transport and precise timing. Its low-power operating approach is intended to improve energy efficiency in broadband gateways, data-center networking equipment, wireless base stations, and enterprise systems.
The 138-QFN package concentrates a high-speed, multiport interface into a compact 12 mm × 12 mm surface-mount footprint. Its exposed thermal pad supports heat transfer through the PCB, but thermal performance still depends on the number of active ports, copper-cable reach, supply voltage, ambient temperature, and board construction. Differential pairs for each Gigabit port require controlled PCB routing, while the high-speed serial links demand short, continuous return paths and properly modeled termination networks.
Typical installations include carrier access platforms, Ethernet aggregation equipment, enterprise routers, broadband access nodes, wireless base-station backhaul, and data-center network interfaces. In these systems, the PHY can provide four copper ports behind one host-facing interface, reducing physical interface count and simplifying control software. Designers should confirm the required MAC interface, synchronization features, reference clocks, cable reach, regulatory constraints, and thermal conditions against the manufacturer datasheet before releasing the PCB layout.
For a new layout, place decoupling capacitors close to the power terminals, route each 10/100/1000BASE-T channel as a controlled-impedance differential pair, and provide unobstructed thermal copper beneath the exposed pad. Confirm the complete power-up sequence and interface timing with the system controller. Avoid substituting a different VSC8514 ordering code until its grade, revision, and feature differences have been checked against the target design requirements.
This page organizes the product identity, verified package information, candidate same-family drop-in options, application guidance, comparison parameters, and PCB design considerations. It is intended to help engineers narrow the correct Ethernet PHY ordering code while keeping package compatibility and thermal constraints explicit.
ドロップイン代替品: VSC8514XMK-13 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: VSC8514XMK-13 (同一形状・フットプリント) — 相違点: Package, Synchronous Ethernet, Power Management.
VSC8514XMK-03
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →VSC8514XMK-11
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
VSC8514XMK-14
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →VSC8514XMK-13 仕様
| Product Type | Quad-port Gigabit Ethernet PHY |
| Number of Ports | 4 ports |
| Ethernet Speed | 10/100/1000BASE-T |
| Medium | Copper twisted-pair |
| Host Interface | QSGMII and SGMII |
| Synchronous Ethernet | Supported |
| TDM Backhaul | Supported |
| Application Areas | Broadband gateways, data centers, enterprise networks, wireless base stations, and carrier equipment |
| Power Architecture | Single low-power supply |
| パッケージ | 138-QFN, 12 mm × 12 mm |
| 実装タイプ | Surface mount |
| Package Code | XMK |
| Exposed Thermal Pad | Present |
VSC8514XMK-13 xmk ピン配置ガイド
VSC8514XMK-13 (xmk パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: VSC8514XMK-13.
詳細は データシート をご参照ください。
主な用途
VSC8514XMK-13 の用途: 6 件s: Enterprise Network Equipment, Data-Center Network Interfaces, Broadband Gateway and CPE, Wireless Base-Station Backhaul, Industrial Ethernet Control, Carrier Access and TDM Transport.
Enterprise Network Equipment
The VSC8514XMK-13 is appropriate for enterprise switches, routers, and access appliances requiring four Gigabit Ethernet copper ports in one device. Its 10/100/1000BASE-T capability covers common LAN links, while QSGMII or SGMII connectivity provides a high-speed path to a switching or routing block. Consolidating four PHYs in one 138-QFN package reduces board area and power-management overhead. Designers should reserve space for the exposed thermal pad, preserve controlled-impedance routing on every copper channel, and verify that the selected ordering code supports the required temperature grade and interface configuration.
おすすめ
Data-Center Network Interfaces
The VSC8514XMK-13 can support low-power copper-facing network interfaces in data-center switches, servers, and edge aggregation equipment. Four integrated 10/100/1000BASE-T ports allow one PHY device to serve multiple 1 GbE links while the QSGMII or SGMII interface connects to a central switching fabric. The low-power operating approach helps control system consumption in densely deployed equipment. Thermal and signal-integrity planning remain critical because four active channels, the 12 mm × 12 mm QFN package, and high-speed serial links can concentrate heat and demand precise return-path routing.
おすすめ
Broadband Gateway and CPE
The VSC8514XMK-13 fits broadband gateways and customer-premises equipment that need several Gigabit Ethernet service ports without using four separate PHY packages. Four 10/100/1000BASE-T channels provide LAN connectivity for home gateways, fiber termination systems, and enterprise CPE, while the host-facing serial interface transfers traffic to an access processor. Low-power operation is valuable where continuously connected customer equipment must meet energy-efficiency targets. The PCB should place the PHY close to the Ethernet connectors, follow differential-pair geometry rules, and provide adequate exposed-pad cooling for sustained multi-port traffic.
おすすめ
Wireless Base-Station Backhaul
The VSC8514XMK-13 is applicable to wireless base-station and carrier backhaul equipment because the family supports TDM backhaul, Synchronous Ethernet, and four copper Gigabit Ethernet ports. These capabilities allow equipment designers to combine traffic transport and precision timing functions around a multiport copper interface. The QSGMII or SGMII connection supports high-bandwidth aggregation toward a network processor or switch. Before deployment, verify the exact clocking, Synchronous Ethernet configuration, interface timing, and temperature requirements for the base-station environment using the manufacturer documentation.
おすすめ
Industrial Ethernet Control
The VSC8514XMK-13 can support industrial controllers, factory communication equipment, and managed automation endpoints requiring four Gigabit Ethernet ports. Its consolidated PHY architecture simplifies the physical-layer portion of a multiport industrial network while retaining SGMII and QSGMII-class host connectivity. Industrial implementations must confirm the ordering code’s temperature grade, isolation requirements, conducted-emissions expectations, and long-term component availability. PCB design should separate sensitive clocking and power paths from Ethernet differential pairs, use manufacturer-recommended filtering and terminations, and preserve thermal continuity beneath the QFN exposed pad.
おすすめ
Carrier Access and TDM Transport
The VSC8514XMK-13 fits carrier-access platforms and transport equipment that combine four 10/100/1000BASE-T service ports with TDM backhaul and Synchronous Ethernet capability. These features allow a network appliance to manage multiple access links while maintaining timing relationships across the system. The 138-QFN package provides a compact implementation, but four active copper PHYs require careful thermal design and channel-layout discipline. Engineers should confirm clock architecture, TDM lane behavior, line-rate limits, cable reach, and regulatory requirements for the finished carrier system before committing the layout.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: VSC8514XMK-13 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | VSC8514XMK-03 | VSC8514XMK-11 | VSC8514XMK-14 |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 138-QFN (12x12) | 138-QFN (12x12) | 138-QFN (12x12) | 138-QFN (12x12) |
| Port Count | 4 ports | 4 ports | 4 ports | 4 ports |
| Ethernet Support | 10/100/1000BASE-T | 10/100/1000BASE-T | 10/100/1000BASE-T | 10/100/1000BASE-T |
| Host Interface | QSGMII and SGMII | QSGMII and SGMII | QSGMII and SGMII | QSGMII with no SyncE |
| Synchronous Ethernet | Supported | Supported | Supported | No SyncE |
| TDM Backhaul | Supported | Supported | Supported | Supported |
| Power Architecture | Single low-power supply | Single low-power supply | Single low-power supply | Single low-power supply |
主な差別化要因
- Retains Synchronous Ethernet capability (vs VSC8514XMK-14)
- Matches the 138-QFN footprint of established same-family options (vs VSC8514XMK-03)
- Four-port integration reduces physical interface count (vs VSC8514XMK-11)
設計ノート
Route each 10/100/1000BASE-T channel as a controlled-impedance differential pair and follow the manufacturer’s reference layout for connector, magnetics, and PHY spacing. Keep the QSGMII or SGMII traces short, provide uninterrupted reference planes beneath the links, and avoid splitting return paths beneath high-speed nets. Four active copper channels plus the high-speed host interface make small routing discontinuities more consequential than in a single-port design.
Use the exposed pad as a thermal path into the PCB rather than leaving it isolated. Add a manufacturer-compliant land pattern with short thermal-via connections and distribute copper where board area permits. Estimated thermal performance depends on four active ports, ambient temperature, copper area, via count, and enclosure airflow; none of those values is specified here, so determine junction-temperature margin through board-level thermal analysis rather than relying on package size alone.
Place all power and ground decoupling components directly beside their associated device terminals, with especially short return paths for the high-speed interface supplies. Keep switching supplies, magnetics, and other noisy sources away from clock and Ethernet differential routing. Confirm voltage rails, sequencing, current limits, and startup requirements against the manufacturer datasheet before selecting capacitors or converters.
Do not treat the -03, -11, -13, and -14 suffixes as interchangeable packing codes. They are distinct ordering codes whose temperature, interface, and configuration characteristics must be checked. The -14 listing explicitly identifies industrial temperature and no Synchronous Ethernet, while the -13 product family supports SyncE. A same-package device can therefore fail functionally even when the PCB footprint remains unchanged.
コンプライアンス情報
The product is an industrial and carrier Ethernet interface IC rather than an automotive-qualified device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer product documentation.