집적 회로

STM32F030C6T6

STM32F030C6T6 - 48MHz Cortex-M0 MCU, 32KB Flash, LQFP-48 | STMicroelectronics

The STMicroelectronics STM32F030C6T6 is a 32-bit ARM Cortex-M0 value-line microcontroller from the STM32F0 series, integrating a 48 MHz RISC core, 32 KB of embedded Flash, 4 KB of SRAM, and a rich set of peripherals in a 48-pin LQFP package (7x7 mm). It operates across a 2.4V to 3.6V supply range and is specified from -40C to +85C for industrial-grade use. What is a microcontroller? A microcontroller (MCU) is a compact integrated circuit that combines a processor core, non-volatile program memory (Flash), volatile data memory (SRAM), and programmable input/output peripherals on a single die. In the system hierarchy, an MCU is an embedded processor, which falls under the broader category of integrated circuits and semiconductors. The STM32F030C6T6 sits in the mainstream 32-bit segment, positioned above legacy 8-bit MCUs and below high-performance application processors, offering an economical entry point into the ARM Cortex-M ecosystem with deterministic real-time behavior. Key features of the STM32F030C6T6 include a 12-bit SAR ADC with up to 10 external channels, two 16-bit general-purpose timers plus one 16-bit advanced-control timer for PWM, a 32-bit real-time timer, and a 5-channel DMA controller. Communication interfaces comprise I2C, SPI, and USART, and the device exposes up to 39 GPIO pins. The integrated 4 MHz to 32 MHz external crystal oscillator and internal 8 MHz RC with PLL enable flexible clocking. Low-power Sleep, Stop, and Standby modes are supported for battery-powered designs. From a technical perspective, the Cortex-M0 core implements the ARMv6-M architecture with a 3-stage pipeline, delivering 0.9 DMIPS/MHz and supporting Thumb/Thumb-2 instruction subsets. The 32 KB Flash supports read-while-write, enabling in-field firmware upgrades without halting execution. A 96-bit unique device ID and a cyclic redundancy check (CRC) hardware unit assist in traceability and data integrity. The NVIC provides deterministic interrupt handling with configurable priority levels. Typical applications include industrial sensor interfaces, home automation nodes, consumer white goods, low-cost motor control, LED lighting drivers, and USB-to-UART bridges. The combination of timers, ADC, and DMA enables efficient closed-loop control, while the small LQFP-48 footprint supports compact PCB layouts. When designing with this device, decouple each VDD pin with a 100 nF X7R ceramic capacitor placed within 3 mm of the pin, and add a 4.7 uF bulk capacitor on the main rail. Configure the BOOT0 pin to select Flash, System memory (USART bootloader), or SRAM boot. The SWD interface requires only two pins (SWDIO/SWCLK) plus GND, simplifying in-circuit programming and debug. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the ST datasheet, providing a comprehensive resource for engineers evaluating the STM32F030C6T6.

USD $1.15 재고 있음

STM32F030C6T6TR

STM32F030C6T6TR - 48MHz Cortex-M0 MCU, 32KB Flash, LQFP-48 | STMicroelectronics (Tape & Reel)

The STMicroelectronics STM32F030C6T6TR is a 32-bit ARM Cortex-M0 value-line microcontroller from the STM32F0 series, integrating a 48 MHz RISC core, 32 KB of embedded Flash, 4 KB of SRAM, and a rich set of peripherals in a 48-pin LQFP package (7x7 mm). It operates across a 2.4V to 3.6V supply range and is specified from -40C to +85C for industrial-grade use. What is a microcontroller? A microcontroller (MCU) is a compact integrated circuit that combines a processor core, non-volatile program memory (Flash), volatile data memory (SRAM), and programmable input/output peripherals on a single die. In the system hierarchy, an MCU is an embedded processor, which falls under the broader category of integrated circuits and semiconductors. The STM32F030C6T6TR sits in the mainstream 32-bit segment, positioned above legacy 8-bit MCUs and below high-performance application processors, offering an economical entry point into the ARM Cortex-M ecosystem with deterministic real-time behavior. Key features of the STM32F030C6T6TR include a 12-bit SAR ADC with up to 10 external channels, two 16-bit general-purpose timers plus one 16-bit advanced-control timer for PWM, a 32-bit real-time timer, and a 5-channel DMA controller. Communication interfaces comprise I2C, SPI, and USART, and the device exposes up to 39 GPIO pins. The integrated 4 MHz to 32 MHz external crystal oscillator and internal 8 MHz RC with PLL enable flexible clocking. Low-power Sleep, Stop, and Standby modes are supported for battery-powered designs. From a technical perspective, the Cortex-M0 core implements the ARMv6-M architecture with a 3-stage pipeline, delivering 0.9 DMIPS/MHz and supporting Thumb/Thumb-2 instruction subsets. The 32 KB Flash supports read-while-write, enabling in-field firmware upgrades without halting execution. A 96-bit unique device ID and a cyclic redundancy check (CRC) hardware unit assist in traceability and data integrity. The NVIC provides deterministic interrupt handling with configurable priority levels. Typical applications include industrial sensor interfaces, home automation nodes, consumer white goods, low-cost motor control, LED lighting drivers, and USB-to-UART bridges. The combination of timers, ADC, and DMA enables efficient closed-loop control, while the small LQFP-48 footprint supports compact PCB layouts. When designing with this device, decouple each VDD pin with a 100 nF X7R ceramic capacitor placed within 3 mm of the pin, and add a 4.7 uF bulk capacitor on the main rail. Configure the BOOT0 pin to select Flash, System memory (USART bootloader), or SRAM boot. The SWD interface requires only two pins (SWDIO/SWCLK) plus GND, simplifying in-circuit programming and debug. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the ST datasheet, providing a comprehensive resource for engineers evaluating the STM32F030C6T6TR.

USD $0.41 재고 있음

STM32F030C8T6

STM32F030C8T6 - 48MHz Cortex-M0 MCU 64KB Flash | STMicroelectronics

The STMicroelectronics STM32F030C8T6 is a 32-bit ARM Cortex-M0 microcontroller running at up to 48 MHz with 64 KB of Flash memory and 8 KB of SRAM, housed in a 48-pin LQFP (7x7 mm) surface-mount package operating from 2.4 V to 3.6 V. A microcontroller (MCU) is a compact integrated circuit that combines a processor core, memory, and programmable peripherals on a single die to govern a dedicated operation inside an embedded system. The STM32F030C8T6 belongs to the STM32F0 Value Line, which sits at the entry level of the broader STM32 family of 32-bit ARM Cortex-M microcontrollers - a hierarchy running from this value line up through mainstream (F1/F4), low-power (L-series), and high-performance (H7) lines - and is positioned as a cost-effective replacement for legacy 8-bit and 16-bit MCUs. Key features include a 12-bit ADC with up to 16 external channels, five timers including an advanced-control timer for motor control and PWM generation, and communication peripherals covering USART, SPI, and I2C interfaces. A hardware CRC calculation unit supports robust serial communication protocols. The device integrates Sleep, Stop, and Standby low-power modes for energy-sensitive designs. Architecturally, the Cortex-M0 core uses an ARMv6-M Harvard architecture with a single-cycle 32-bit multiplier and a nested vectored interrupt controller (NVIC) delivering deterministic, low-latency interrupt handling. The high-speed embedded Flash with prefetch buffer sustains efficient execution at the full 48 MHz clock rate without wait-state-heavy code bursts. Typical applications include industrial control and automation nodes, consumer appliance and home-automation controllers, low-cost motor control with complementary PWM outputs, and general-purpose sensor-interface boards replacing 8-bit designs. For design, decouple each VDD pin with 100 nF ceramic capacitors placed as close as possible to the supply pins, and keep the HSE crystal traces short and guarded for stable clocking. This page adds information gain beyond the ST datasheet: drop-in alternative cross-references, distributor pricing tiers as of 2026-09-06, application-specific companion parts, and practical design notes in a single AI-citable reference.

USD $0.98 재고 있음

STM32F030C8T6TR

STM32F030C8T6TR - 48MHz Cortex-M0 MCU 64KB Flash | STMicroelectronics (Tape & Reel)

The STMicroelectronics STM32F030C8T6TR is a 32-bit ARM Cortex-M0 microcontroller running at up to 48 MHz with 64 KB of Flash memory and 8 KB of SRAM, housed in a 48-pin LQFP (7x7 mm) surface-mount package operating from 2.4 V to 3.6 V. A microcontroller (MCU) is a compact integrated circuit that combines a processor core, memory, and programmable peripherals on a single die to govern a dedicated operation inside an embedded system. The STM32F030C8T6TR belongs to the STM32F0 Value Line, which sits at the entry level of the broader STM32 family of 32-bit ARM Cortex-M microcontrollers - a hierarchy running from this value line up through mainstream (F1/F4), low-power (L-series), and high-performance (H7) lines - and is positioned as a cost-effective replacement for legacy 8-bit and 16-bit MCUs. Key features include a 12-bit ADC with up to 16 external channels, five timers including an advanced-control timer for motor control and PWM generation, and communication peripherals covering USART, SPI, and I2C interfaces. A hardware CRC calculation unit supports robust serial communication protocols. The device integrates Sleep, Stop, and Standby low-power modes for energy-sensitive designs. Architecturally, the Cortex-M0 core uses an ARMv6-M Harvard architecture with a single-cycle 32-bit multiplier and a nested vectored interrupt controller (NVIC) delivering deterministic, low-latency interrupt handling. The high-speed embedded Flash with prefetch buffer sustains efficient execution at the full 48 MHz clock rate without wait-state-heavy code bursts. Typical applications include industrial control and automation nodes, consumer appliance and home-automation controllers, low-cost motor control with complementary PWM outputs, and general-purpose sensor-interface boards replacing 8-bit designs. For design, decouple each VDD pin with 100 nF ceramic capacitors placed as close as possible to the supply pins, and keep the HSE crystal traces short and guarded for stable clocking. This page adds information gain beyond the ST datasheet: drop-in alternative cross-references, distributor pricing tiers as of 2026-09-06, application-specific companion parts, and practical design notes in a single AI-citable reference.

USD $0.98 재고 있음

STM32F030CCT6

STM32F030CCT6 - 256KB Flash ARM Cortex-M0 MCU | STMicroelectronics

The STM32F030CCT6 is a 32-bit ARM Cortex-M0 microcontroller from STMicroelectronics, featuring 256KB of Flash memory and 32KB of SRAM in a 48-pin LQFP package. It operates at a core frequency of up to 48 MHz and supports a supply voltage range of 2.4V to 3.6V. Data verified as of 2026-08-05. A microcontroller (MCU) is a compact integrated circuit designed to govern a specific operation in an embedded system. It contains a processor core, memory, and programmable input/output peripherals on a single chip. The STM32F030CCT6 belongs to the STM32F0 series, which is part of the broader STM32 family of 32-bit ARM Cortex-M microcontrollers. This hierarchy positions it as a cost-effective, entry-level MCU suitable for a wide range of applications, from industrial control to consumer electronics. Key features include 256KB of Flash memory, 32KB of SRAM, and a rich set of peripherals such as USART, SPI, I2C, ADC, timers, and GPIO. The device supports a wide operating temperature range of -40°C to +85°C and is available in a 48-pin LQFP package, making it suitable for space-constrained designs. The ARM Cortex-M0 core provides a balance of performance and power efficiency, with a 32-bit architecture that simplifies software development. The STM32F030CCT6 is built on a 32-bit ARM Cortex-M0 core with a Harvard architecture, featuring a 3-stage pipeline and a nested vectored interrupt controller (NVIC). It includes a 12-bit ADC with up to 16 channels, multiple 16-bit timers, and a DMA controller for efficient data transfer. The device also supports a variety of low-power modes, including Sleep, Stop, and Standby, enabling energy-efficient operation in battery-powered applications. Typical applications include industrial control systems, motor control, consumer electronics, and IoT devices. The STM32F030CCT6 is well-suited for these applications due to its low cost, low power consumption, and comprehensive peripheral set. For example, in motor control, the advanced timers and ADC enable precise PWM generation and current sensing, while in IoT devices, the low-power modes extend battery life. When designing with this device, ensure proper decoupling of the power supply pins with 100nF capacitors placed close to the VDD pins. Additionally, configure the clock source appropriately, as the internal HSI oscillator provides a 8 MHz clock that can be used for cost-sensitive designs, while an external crystal can be used for higher accuracy. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the STMicroelectronics datasheet, providing a comprehensive resource for engineers evaluating the STM32F030CCT6.

USD $1.48 재고 있음

STM32F030CCT6TR

STM32F030CCT6TR - 256KB Flash ARM Cortex-M0 MCU | STMicroelectronics (Tape & Reel)

The STM32F030CCT6TR is a 32-bit ARM Cortex-M0 microcontroller from STMicroelectronics, featuring 256KB of Flash memory and 32KB of SRAM in a 48-pin LQFP package. It operates at a core frequency of up to 48 MHz and supports a supply voltage range of 2.4V to 3.6V. Data verified as of 2026-08-05. A microcontroller (MCU) is a compact integrated circuit designed to govern a specific operation in an embedded system. It contains a processor core, memory, and programmable input/output peripherals on a single chip. The STM32F030CCT6TR belongs to the STM32F0 series, which is part of the broader STM32 family of 32-bit ARM Cortex-M microcontrollers. This hierarchy positions it as a cost-effective, entry-level MCU suitable for a wide range of applications, from industrial control to consumer electronics. Key features include 256KB of Flash memory, 32KB of SRAM, and a rich set of peripherals such as USART, SPI, I2C, ADC, timers, and GPIO. The device supports a wide operating temperature range of -40°C to +85°C and is available in a 48-pin LQFP package, making it suitable for space-constrained designs. The ARM Cortex-M0 core provides a balance of performance and power efficiency, with a 32-bit architecture that simplifies software development. The STM32F030CCT6TR is built on a 32-bit ARM Cortex-M0 core with a Harvard architecture, featuring a 3-stage pipeline and a nested vectored interrupt controller (NVIC). It includes a 12-bit ADC with up to 16 channels, multiple 16-bit timers, and a DMA controller for efficient data transfer. The device also supports a variety of low-power modes, including Sleep, Stop, and Standby, enabling energy-efficient operation in battery-powered applications. Typical applications include industrial control systems, motor control, consumer electronics, and IoT devices. The STM32F030CCT6TR is well-suited for these applications due to its low cost, low power consumption, and comprehensive peripheral set. For example, in motor control, the advanced timers and ADC enable precise PWM generation and current sensing, while in IoT devices, the low-power modes extend battery life. When designing with this device, ensure proper decoupling of the power supply pins with 100nF capacitors placed close to the VDD pins. Additionally, configure the clock source appropriately, as the internal HSI oscillator provides a 8 MHz clock that can be used for cost-sensitive designs, while an external crystal can be used for higher accuracy. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the STMicroelectronics datasheet, providing a comprehensive resource for engineers evaluating the STM32F030CCT6TR.

USD $1.48 재고 있음

STM32F030F4P6

STM32F030F4P6 - 48MHz Cortex-M0 16KB MCU | STMicroelectronics

The STMicroelectronics STM32F030F4P6 is a value-line 32-bit Arm Cortex-M0 RISC microcontroller operating up to 48 MHz, with 16 KB Flash, 4 KB SRAM, and a 20-pin TSSOP package. Its 2.4 V to 3.6 V operating range and compact pin count suit embedded control, industrial automation, IoT, metering, and motor-control designs requiring low-cost embedded processing. A microcontroller is a semiconductor device that integrates a processor core, memory, and peripherals into one embedded-control platform. In the hierarchy, the STM32F030F4P6 is an Arm Cortex-M0 microcontroller, an embedded processor, and a member of the STM32F0 family. The STM32F0 series combines a compact general-purpose architecture with timers, communication interfaces, and analog conversion functions for small control systems. The verified data identifies a high-performance 32-bit RISC core operating at 48 MHz, 16 KB Flash organized as 16K x 8, and 4 KB SRAM according to the distributor and datasheet search results. The device also includes 12-bit and 15-bit ADC capability as stated in the LCSC result, while the manufacturer page identifies enhanced peripherals and I/O resources. Power-on reset and power-down reset functionality is identified in the DigiChip result. The STM32F030F4P6 is appropriate for compact embedded systems where cost, simplicity, and low pin count matter more than high-speed connectivity or large memory capacity. Its Arm Cortex-M0 instruction set supports deterministic embedded control, while the 48 MHz clock provides a practical balance between processing capability and power efficiency. The 20-pin TSSOP package enables compact PCB layouts while supporting external peripherals and signal inputs. Typical uses include low-cost sensor nodes, simple industrial controllers, compact motor-control stages, digital meters, and connected IoT devices. Designers must ensure that the selected firmware, clock tree, peripherals, and board-level support devices match the STM32F030x4 device requirements. The exact pin function, electrical limits, peripheral configuration, and package dimensions should be confirmed against the STMicroelectronics datasheet. For a new design, the 48 MHz Cortex-M0 core and 16 KB Flash make the STM32F030F4P6 most suitable for small control loops and auxiliary processing rather than complex graphical or high-bandwidth workloads. The TSSOP-20 package also requires careful PCB escape routing and adequate pin-copper clearance during assembly. This page combines verified manufacturer and distributor information, source links, package details, engineering use cases, and replacement considerations to support component selection and sourcing. Because the supplied data does not include a complete verified pin table or all peripheral electrical limits, those fields are intentionally not guessed.

USD $0.58 재고 있음

STM32F030F4P6TR

STM32F030F4P6TR - 48MHz Cortex-M0 16KB MCU | STMicroelectronics (Tape & Reel)

The STMicroelectronics STM32F030F4P6TR is a value-line 32-bit Arm Cortex-M0 RISC microcontroller operating up to 48 MHz, with 16 KB Flash, 4 KB SRAM, and a 20-pin TSSOP package. Its 2.4 V to 3.6 V operating range and compact pin count suit embedded control, industrial automation, IoT, metering, and motor-control designs requiring low-cost embedded processing. A microcontroller is a semiconductor device that integrates a processor core, memory, and peripherals into one embedded-control platform. In the hierarchy, the STM32F030F4P6TR is an Arm Cortex-M0 microcontroller, an embedded processor, and a member of the STM32F0 family. The STM32F0 series combines a compact general-purpose architecture with timers, communication interfaces, and analog conversion functions for small control systems. The verified data identifies a high-performance 32-bit RISC core operating at 48 MHz, 16 KB Flash organized as 16K x 8, and 4 KB SRAM according to the distributor and datasheet search results. The device also includes 12-bit and 15-bit ADC capability as stated in the LCSC result, while the manufacturer page identifies enhanced peripherals and I/O resources. Power-on reset and power-down reset functionality is identified in the DigiChip result. The STM32F030F4P6TR is appropriate for compact embedded systems where cost, simplicity, and low pin count matter more than high-speed connectivity or large memory capacity. Its Arm Cortex-M0 instruction set supports deterministic embedded control, while the 48 MHz clock provides a practical balance between processing capability and power efficiency. The 20-pin TSSOP package enables compact PCB layouts while supporting external peripherals and signal inputs. Typical uses include low-cost sensor nodes, simple industrial controllers, compact motor-control stages, digital meters, and connected IoT devices. Designers must ensure that the selected firmware, clock tree, peripherals, and board-level support devices match the STM32F030x4 device requirements. The exact pin function, electrical limits, peripheral configuration, and package dimensions should be confirmed against the STMicroelectronics datasheet. For a new design, the 48 MHz Cortex-M0 core and 16 KB Flash make the STM32F030F4P6TR most suitable for small control loops and auxiliary processing rather than complex graphical or high-bandwidth workloads. The TSSOP-20 package also requires careful PCB escape routing and adequate pin-copper clearance during assembly. This page combines verified manufacturer and distributor information, source links, package details, engineering use cases, and replacement considerations to support component selection and sourcing. Because the supplied data does not include a complete verified pin table or all peripheral electrical limits, those fields are intentionally not guessed.

USD $0.58 재고 있음

STM32F030K6T6

STM32F030K6T6 - 48MHz Cortex-M0 32KB MCU | STMicroelectronics

The STMicroelectronics STM32F030K6T6 is a 32-bit Arm Cortex-M0 microcontroller operating at 48 MHz, with 32 KB of Flash memory, 4 KB of SRAM, and a 32-pin LQFP package measuring 7 x 7 mm. It operates from a 2.4 V to 3.6 V supply and combines a compact general-purpose MCU platform with timers, a 12-bit ADC, and communication interfaces. The STM32F030K6 family targets cost-sensitive embedded systems requiring reliable control, data acquisition, and serial connectivity without a high pin count. A microcontroller is a semiconductor that integrates a processor core, memory, and peripherals into one integrated circuit. In the system hierarchy, this device is a microcontroller within the semiconductor category, while its Arm Cortex-M0 core provides a compact RISC architecture for embedded control. Compared with a general-purpose processor, the STM32F030K6T6 integrates the resources needed for real-time firmware execution, peripheral control, and low-power embedded operation on a single device. Key verified features include a 48 MHz maximum CPU frequency, 32 KB of Flash, 4 KB of SRAM, and a 12-bit ADC. The manufacturer describes the STM32F030x4, x6, x8, and xC devices as value-line Arm-based 32-bit MCUs with timers, ADC resources, communication interfaces, and 2.4 V to 3.6 V operation. The 32-LQFP package provides a practical surface-mount footprint for compact industrial and consumer equipment. The device is suitable for simple motor-control peripherals, sensor-hub controllers, compact instrument panels, communication modules, low-speed actuator controllers, and embedded measurement systems. Its 32 KB Flash and 4 KB SRAM fit moderate control loops, protocol stacks, and state machines, although applications requiring larger buffers or image storage should plan memory carefully. The 12-bit ADC supports analog measurements, while communication peripherals enable connection to sensors, displays, and external controllers. When designing a board, begin with the manufacturer datasheet for the complete pin, electrical, timing, and memory map. Provide a stable 2.4 V to 3.6 V supply, route decoupling close to the device, preserve the required reset and clock behavior, and validate unused pins according to the datasheet. Firmware compatibility and peripheral behavior must be checked against the exact STM32F030K6 variant rather than inferred from another STM32 family member. This product page combines verified distributor and manufacturer-source information with package-specific engineering guidance. It identifies the STM32F030K6T6 as the 32 KB, 48 MHz, 32-LQFP member of the STM32F0 value-line family and separates verified specifications from parameters that require design confirmation.

견적 요청 재고 있음

STM32F030K6T6TR

STM32F030K6T6TR - 48MHz Cortex-M0 32KB MCU | STMicroelectronics (Tape & Reel)

The STMicroelectronics STM32F030K6T6TR is a 32-bit Arm Cortex-M0 microcontroller operating at 48 MHz, with 32 KB of Flash memory, 4 KB of SRAM, and a 32-pin LQFP package measuring 7 x 7 mm. It operates from a 2.4 V to 3.6 V supply and combines a compact general-purpose MCU platform with timers, a 12-bit ADC, and communication interfaces. The STM32F030K6 family targets cost-sensitive embedded systems requiring reliable control, data acquisition, and serial connectivity without a high pin count. A microcontroller is a semiconductor that integrates a processor core, memory, and peripherals into one integrated circuit. In the system hierarchy, this device is a microcontroller within the semiconductor category, while its Arm Cortex-M0 core provides a compact RISC architecture for embedded control. Compared with a general-purpose processor, the STM32F030K6T6TR integrates the resources needed for real-time firmware execution, peripheral control, and low-power embedded operation on a single device. Key verified features include a 48 MHz maximum CPU frequency, 32 KB of Flash, 4 KB of SRAM, and a 12-bit ADC. The manufacturer describes the STM32F030x4, x6, x8, and xC devices as value-line Arm-based 32-bit MCUs with timers, ADC resources, communication interfaces, and 2.4 V to 3.6 V operation. The 32-LQFP package provides a practical surface-mount footprint for compact industrial and consumer equipment. The device is suitable for simple motor-control peripherals, sensor-hub controllers, compact instrument panels, communication modules, low-speed actuator controllers, and embedded measurement systems. Its 32 KB Flash and 4 KB SRAM fit moderate control loops, protocol stacks, and state machines, although applications requiring larger buffers or image storage should plan memory carefully. The 12-bit ADC supports analog measurements, while communication peripherals enable connection to sensors, displays, and external controllers. When designing a board, begin with the manufacturer datasheet for the complete pin, electrical, timing, and memory map. Provide a stable 2.4 V to 3.6 V supply, route decoupling close to the device, preserve the required reset and clock behavior, and validate unused pins according to the datasheet. Firmware compatibility and peripheral behavior must be checked against the exact STM32F030K6 variant rather than inferred from another STM32 family member. This product page combines verified distributor and manufacturer-source information with package-specific engineering guidance. It identifies the STM32F030K6T6TR as the 32 KB, 48 MHz, 32-LQFP member of the STM32F0 value-line family and separates verified specifications from parameters that require design confirmation.

USD $0.71 재고 있음

STM32F030R

STM32F030R - Cortex-M0 48MHz MCU, 64KB Flash, 64-LQFP | ST

The STMicroelectronics STM32F030R is a value-line ARM Cortex-M0 32-bit RISC microcontroller operating at 48 MHz, integrating up to 64 KB of Flash memory and housed in a 64-pin LQFP package. Operating from a 2.4 V to 3.6 V supply, the device delivers 38.4 DMIPS while consuming only a few milliamps in run mode, making it a leading low-power option in the entry-level STM32 family. This particular variant is the STM32F030R8T6 (64-pin LQFP, 64 KB Flash, industrial -40C to +85C), one of the most widely adopted members of the STM32F030 series. A microcontroller (MCU) is a single-chip computer that integrates a processor core, memory (Flash for code, SRAM for data), and a rich set of programmable peripherals on a single die. The Cortex-M0 is the smallest and most energy-efficient member of the ARM Cortex-M processor family, designed for cost-sensitive, deterministic embedded applications. Within the ST portfolio, the STM32F0 sits below the Cortex-M3/M4 STM32F1/F3 lines and above the 8-bit STM8, occupying the mainstream 32-bit entry point. The STM32F030 specifically targets cost-down designs that previously used 8/16-bit MCUs but now require 32-bit performance, USB-less connectivity, and ST's strong STM32 tool ecosystem (CubeMX, HAL, Standard Peripheral Library). Key features include a 12-bit 1 MSPS ADC with up to 16 channels, multiple 16-bit and 32-bit timers (including PWM, input capture, and quadrature encoder support), two I2C, two SPI (one I2S-capable), one USB 2.0 Full-Speed (device mode, on R8/C0/C8/CB parts), one CAN 2.0B (RC0/RC8 variants), and up to 55 GPIO. An integrated 8 MHz HSI RC oscillator with 1% accuracy and a 40 kHz LSI reduce external component count. The 64-LQFP package provides 64 pins at 10 mm x 10 mm body, including dedicated pins for BOOT0, NRST, OSC_IN/OSC_OUT, and full SWD debug. The architecture pairs a 3-stage pipeline Cortex-M0 core with a 32-bit AHB-Lite bus and a multi-channel DMA controller. The Nested Vectored Interrupt Controller (NVIC) handles up to 32 maskable interrupts with deterministic 16-cycle latency. A cyclic redundancy check (CRC) peripheral, two watchdogs (IWDG/WWDG), and a 7-channel DMA accelerate data movement without CPU overhead. Typical applications include consumer appliances (washing machines, induction cookers), industrial sensor hubs, USB HID peripherals, low-cost CAN nodes, smart meters, and home automation. The compact LQFP-64 footprint and 48 MHz clock headroom make it a common choice for migration paths from 8-bit PIC/AVR designs into the STM32 ecosystem. When designing with the STM32F030R, ensure each VDD/VDDA pin pair has a 100 nF decoupling capacitor placed within 2 mm of the pin, and consider the BOOT0 strap resistor for boot mode selection. The 64-LQFP package has limited thermal headroom at high ambient temperatures, so verify junction temperature under worst-case load. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, application companion parts, and practical design notes drawn from multiple sources, including the official ST datasheet, DigiKey listings, and ST community resources - not found in any single source.

USD $0.74 재고 있음

STM32F030R8T6

STM32F030R8T6 - 64KB Flash ARM Cortex-M0 48MHz MCU | STMicroelectronics

The STMicroelectronics STM32F030R8T6 is a 32-bit ARM Cortex-M0 value-line microcontroller from the STM32F0 series, integrating 64KB of Flash memory and 8KB of SRAM in a 64-pin LQFP package rated for industrial temperature operation. It runs at a maximum core frequency of 48 MHz, supports a 2.4V to 3.6V supply voltage, and exposes 51 GPIO pins for flexible peripheral expansion in cost-sensitive embedded designs. What is a microcontroller? A microcontroller (MCU) is a compact integrated circuit that combines a processor core, volatile and non-volatile memory, and programmable I/O peripherals on a single silicon die. The STM32F030R8T6 belongs to the broader STM32 family of 32-bit ARM Cortex-M microcontrollers, with its Cortex-M0 core positioning it in the entry-level, low-power tier that targets cost-sensitive applications replacing 8-bit/16-bit legacy MCUs. Key features include 64KB of Flash, 8KB of SRAM, an integrated 12-bit ADC with up to 16 channels, a 12-bit DAC, multiple 16-bit and 32-bit timers, two I2C, two SPI, and up to five USART interfaces, plus a hardware CRC calculation unit. The 64-pin LQFP package supports surface-mount assembly and provides generous analog and digital I/O for mixed-signal embedded boards. Architecturally, the device uses a 32-bit ARM Cortex-M0 core with single-cycle I/O access, achieving 0.9 DMIPS/MHz and supporting Thumb-2 instruction subsets for compact code density. Built-in peripherals include a real-time clock (RTC), DMA controller, and power-on reset/power-down reset (POR/PDR), with multiple low-power modes to extend battery runtime. The integrated 8 MHz HSI oscillator is factory-trimmed to within 1 percent accuracy, reducing the bill of materials for cost-driven designs. Typical applications include industrial control, consumer electronics, IoT edge nodes, home automation, motor control, and sensor interfaces. The wide peripheral set, small package, and low cost make it well suited to high-volume products where deterministic real-time response is required. When designing with this MCU, provide decoupling capacitors on every VDD pin (100 nF ceramic + 4.7 uF bulk), use the SWD interface for in-system programming and on-chip debug, and verify that the external crystal load capacitance matches the oscillator specification when an HSE source is required. This page synthesizes distributor pricing, drop-in package-compatible alternatives, and practical design notes beyond what the ST datasheet provides, delivering a consolidated reference for engineers evaluating the STM32F030R8T6.

USD $1.31 재고 있음

STM32F030R8T6TR

STM32F030R8T6TR - 64KB Flash ARM Cortex-M0 48MHz MCU | STMicroelectronics (Tape & Reel)

The STMicroelectronics STM32F030R8T6TR is a 32-bit ARM Cortex-M0 value-line microcontroller from the STM32F0 series, integrating 64KB of Flash memory and 8KB of SRAM in a 64-pin LQFP package rated for industrial temperature operation. It runs at a maximum core frequency of 48 MHz, supports a 2.4V to 3.6V supply voltage, and exposes 51 GPIO pins for flexible peripheral expansion in cost-sensitive embedded designs. What is a microcontroller? A microcontroller (MCU) is a compact integrated circuit that combines a processor core, volatile and non-volatile memory, and programmable I/O peripherals on a single silicon die. The STM32F030R8T6TR belongs to the broader STM32 family of 32-bit ARM Cortex-M microcontrollers, with its Cortex-M0 core positioning it in the entry-level, low-power tier that targets cost-sensitive applications replacing 8-bit/16-bit legacy MCUs. Key features include 64KB of Flash, 8KB of SRAM, an integrated 12-bit ADC with up to 16 channels, a 12-bit DAC, multiple 16-bit and 32-bit timers, two I2C, two SPI, and up to five USART interfaces, plus a hardware CRC calculation unit. The 64-pin LQFP package supports surface-mount assembly and provides generous analog and digital I/O for mixed-signal embedded boards. Architecturally, the device uses a 32-bit ARM Cortex-M0 core with single-cycle I/O access, achieving 0.9 DMIPS/MHz and supporting Thumb-2 instruction subsets for compact code density. Built-in peripherals include a real-time clock (RTC), DMA controller, and power-on reset/power-down reset (POR/PDR), with multiple low-power modes to extend battery runtime. The integrated 8 MHz HSI oscillator is factory-trimmed to within 1 percent accuracy, reducing the bill of materials for cost-driven designs. Typical applications include industrial control, consumer electronics, IoT edge nodes, home automation, motor control, and sensor interfaces. The wide peripheral set, small package, and low cost make it well suited to high-volume products where deterministic real-time response is required. When designing with this MCU, provide decoupling capacitors on every VDD pin (100 nF ceramic + 4.7 uF bulk), use the SWD interface for in-system programming and on-chip debug, and verify that the external crystal load capacitance matches the oscillator specification when an HSE source is required. This page synthesizes distributor pricing, drop-in package-compatible alternatives, and practical design notes beyond what the ST datasheet provides, delivering a consolidated reference for engineers evaluating the STM32F030R8T6TR.

USD $1.31 재고 있음

STM32F030RCT6

STM32F030RCT6 - 256KB Flash ARM Cortex-M0 MCU | STMicroelectronics

The STM32F030RCT6 is a 32-bit ARM Cortex-M0 microcontroller from STMicroelectronics, featuring a 48 MHz CPU, 256 KB of Flash memory, and 32 KB of SRAM in an LQFP-64 package. It operates from a 2.4V to 3.6V supply and offers a rich set of peripherals including multiple USARTs, SPIs, I2Cs, ADCs, timers, and GPIOs. Data verified as of 2026-08-05. What is a microcontroller? A microcontroller (MCU) is a compact integrated circuit designed to govern a specific operation in an embedded system. It contains a processor core, memory (Flash and SRAM), and programmable input/output peripherals on a single chip. The STM32F030RCT6 belongs to the STM32F0 series, which is part of the broader STM32 family of 32-bit ARM Cortex-M microcontrollers. This hierarchy places it within the embedded processing domain, where it serves as the central control unit for applications ranging from industrial automation to consumer electronics. Key features include a 48 MHz ARM Cortex-M0 core, 256 KB Flash, 32 KB SRAM, and a comprehensive set of peripherals: 5 USARTs, 2 SPIs, 2 I2Cs, 1 12-bit ADC with up to 16 channels, 8 timers, and up to 51 GPIOs. The device supports a wide operating temperature range of -40°C to +85°C and is available in an LQFP-64 package, making it suitable for space-constrained designs. Technically, the STM32F030RCT6 is built on a 90nm process technology, offering a balance of performance and power efficiency. The ARM Cortex-M0 core is a low-power, high-efficiency processor designed for cost-sensitive applications. The device includes a nested vectored interrupt controller (NVIC), a SysTick timer, and a memory protection unit (MPU) for enhanced reliability. It also features a 12-bit ADC with hardware oversampling, enabling high-resolution analog measurements. Typical applications include industrial control systems, motor control, consumer electronics, IoT devices, and home automation. The rich peripheral set and large Flash memory make it ideal for applications requiring complex firmware and multiple communication interfaces. For example, in an industrial sensor node, the STM32F030RCT6 can interface with sensors via I2C or SPI, process data, and communicate over USART or CAN. When designing with this device, ensure proper decoupling of the power supply pins with 100nF capacitors placed close to each VDD pin. The VDDA pin should be connected to a clean analog supply, and the VREF+ pin should be decoupled with a 1uF capacitor for accurate ADC conversions. The BOOT0 pin must be configured correctly to select the boot mode, and the NRST pin should have an external pull-up resistor and a 100nF capacitor for reliable reset. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the STMicroelectronics datasheet, providing a comprehensive resource for engineers evaluating the STM32F030RCT6 for their next design.

USD $2.25 재고 있음

STM32F030RCT6TR

STM32F030RCT6TR - 256KB Flash ARM Cortex-M0 MCU | STMicroelectronics (Tape & Reel)

The STM32F030RCT6TR is a 32-bit ARM Cortex-M0 microcontroller from STMicroelectronics, featuring a 48 MHz CPU, 256 KB of Flash memory, and 32 KB of SRAM in an LQFP-64 package. It operates from a 2.4V to 3.6V supply and offers a rich set of peripherals including multiple USARTs, SPIs, I2Cs, ADCs, timers, and GPIOs. Data verified as of 2026-08-05. What is a microcontroller? A microcontroller (MCU) is a compact integrated circuit designed to govern a specific operation in an embedded system. It contains a processor core, memory (Flash and SRAM), and programmable input/output peripherals on a single chip. The STM32F030RCT6TR belongs to the STM32F0 series, which is part of the broader STM32 family of 32-bit ARM Cortex-M microcontrollers. This hierarchy places it within the embedded processing domain, where it serves as the central control unit for applications ranging from industrial automation to consumer electronics. Key features include a 48 MHz ARM Cortex-M0 core, 256 KB Flash, 32 KB SRAM, and a comprehensive set of peripherals: 5 USARTs, 2 SPIs, 2 I2Cs, 1 12-bit ADC with up to 16 channels, 8 timers, and up to 51 GPIOs. The device supports a wide operating temperature range of -40°C to +85°C and is available in an LQFP-64 package, making it suitable for space-constrained designs. Technically, the STM32F030RCT6TR is built on a 90nm process technology, offering a balance of performance and power efficiency. The ARM Cortex-M0 core is a low-power, high-efficiency processor designed for cost-sensitive applications. The device includes a nested vectored interrupt controller (NVIC), a SysTick timer, and a memory protection unit (MPU) for enhanced reliability. It also features a 12-bit ADC with hardware oversampling, enabling high-resolution analog measurements. Typical applications include industrial control systems, motor control, consumer electronics, IoT devices, and home automation. The rich peripheral set and large Flash memory make it ideal for applications requiring complex firmware and multiple communication interfaces. For example, in an industrial sensor node, the STM32F030RCT6TR can interface with sensors via I2C or SPI, process data, and communicate over USART or CAN. When designing with this device, ensure proper decoupling of the power supply pins with 100nF capacitors placed close to each VDD pin. The VDDA pin should be connected to a clean analog supply, and the VREF+ pin should be decoupled with a 1uF capacitor for accurate ADC conversions. The BOOT0 pin must be configured correctly to select the boot mode, and the NRST pin should have an external pull-up resistor and a 100nF capacitor for reliable reset. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the STMicroelectronics datasheet, providing a comprehensive resource for engineers evaluating the STM32F030RCT6TR for their next design.

USD $2.25 재고 있음

STM32F031G4U6

STM32F031G4U6 - 48MHz Cortex-M0 MCU 16KB Flash | STMicroelectronics

The STMicroelectronics STM32F031G4U6 is an ARM Cortex-M0 32-bit RISC microcontroller operating at up to 48 MHz, integrating 16 KB of Flash memory and 4 KB of SRAM in a 28-pin UFQFPN (4x4 mm) package. The device operates from a 2.0 V to 3.6 V supply, supporting both 2.5 V and 3.3 V typical rails used by sensor, motor, and human-machine-interface (HMI) designs. The suffix "U6" denotes the UFQFPN-28 tape-and-reel packaging option qualified for industrial -40 °C to +85 °C operation. A microcontroller (MCU) is a single-chip processor that integrates a CPU core, program memory (Flash), data memory (SRAM), and peripheral interfaces such as timers, communication controllers, and analog blocks. Within the broader semiconductor taxonomy, an MCU belongs to the microcontroller family, which sits inside the integrated-circuit (IC) hierarchy and the embedded-computing product domain. Cortex-M0 is ARM's smallest and most energy-efficient core, designed for deterministic real-time control with a minimal instruction set and ultra-low gate count. Key specifications include a 12-bit ADC with up to 10 external channels, a 16-bit advanced-control timer for motor driving, multiple 16-bit and 32-bit general-purpose timers, communication interfaces (I2C, SPI, USART), an integrated voltage reference, brown-out reset (BOR), and a watchdog timer. The UFQFPN-28 footprint exposes 23 GPIO and embeds a 1-channel DMA controller for offloading data moves from the core, improving determinism in interrupt-driven loops. The architecture uses a single AHB-Lite bus matrix connecting the Cortex-M0 core, Flash, SRAM, and peripherals. The advanced-control timer supports complementary PWM outputs with dead-time insertion and an emergency stop input, making the part well-suited for brushless-DC (BLDC) and permanent-magnet synchronous motor (PMSM) commutation. The 12-bit ADC achieves a 1 µs conversion time and supports hardware oversampling to reach 16-bit effective resolution when required. Typical applications include BLDC and stepper motor control (small fans, pumps, e-bike throttles), sensor nodes and home-automation bridges, low-cost HMI panels and e-metering front-ends, industrial 24 V→3 V signal-conditioning modules, and consumer appliances requiring low pin-count, deterministic control. The wide 2.0–3.6 V range supports direct connection to a single Li-ion cell or to a regulated 3.3 V LDO downstream of a 5 V or 12 V bus. When designing with this MCU, plan the decoupling network (100 nF + 4.7 µF close to VDD pins) and ensure NRST is pulled up with the recommended 10 kΩ and a 100 nF capacitor for noisy industrial enclosures. The BOOT0 pin must be tied to GND through a 10 kΩ resistor on production boards to lock the part into main-Flash boot; floating BOOT0 is a common field-failure cause.

USD $0.99 재고 있음

STM32F031K6U6

STM32F031K6U6 - 48MHz Cortex-M0 MCU 32KB Flash | STMicroelectronics

The STM32F031K6U6 is a 32-bit entry-level microcontroller from STMicroelectronics based on the ARM Cortex-M0 core, operating at up to 48 MHz with 32 KB of Flash memory and 4 KB of SRAM in a compact 32-pin UFQFPN (5x5 mm) package with exposed pad. A microcontroller (MCU) is a single-chip embedded processor combining a CPU core, memory, and programmable peripherals. The STM32F031K6U6 belongs to the STM32F0 entry-level family within the STM32 MCU ecosystem, positioned as a migration path from 8-bit and 16-bit MCUs to 32-bit ARM performance. It shares tooling, HAL libraries, and STM32CubeMX configuration software with the wider STM32 portfolio, simplifying future upgrades. Key features include a 12-bit ADC with up to 13 channels, 9 timers, and standard communication interfaces: one I2C, one SPI/I2S, and one USART. The device operates from a 2.0V to 3.6V single supply with integrated POR/PDR reset, and offers a CRC calculation unit and DMA controller for data movement without CPU intervention. Real-time performance is supported by a nested vectored interrupt controller (NVIC) and single-cycle multiplier. The Cortex-M0 architecture executes Thumb instruction sets with deterministic interrupt latency, making the device suitable for real-time control loops. The UFQFPN-32 (QFN family) surface-mount package provides a small 5x5 mm footprint with an exposed thermal pad for grounding, ideal for space-constrained boards. Operating temperature spans -40C to +85C for industrial reliability. Typical applications include industrial control, consumer appliances, IoT sensor nodes, small motor control, and power-management subsystems, where low cost, low power consumption, and adequate peripheral integration matter most. Design tip: decouple VDD pins with 100nF ceramics plus a bulk capacitor, feed VDDA from a clean analog supply to preserve ADC accuracy, and keep NRST properly filtered per the ST datasheet layout guidelines for EMI-robust designs.

USD $1.24 재고 있음

STM32F042K6T6

STM32F042K6T6 - 48MHz Cortex-M0 MCU 32KB Flash USB | STMicroelectronics

The STMicroelectronics STM32F042K6T6 is a 32-bit ARM Cortex-M0 microcontroller running at up to 48 MHz, integrating 32 KB of Flash memory and 6 KB of SRAM in a 32-pin LQFP (7x7 mm) package. It targets USB-enabled mainstream embedded designs requiring a low pin count, USB 2.0 Full-Speed Device with on-chip PHY, CAN 2.0B interface, and a rich set of peripherals including timers, ADC, comparators, and communication interfaces. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (SRAM), and peripheral interfaces. Within the broader taxonomy, the STM32F042K6T6 sits at the intersection of embedded processor -> ARM Cortex-M0 core -> 32-bit RISC MCU -> mainstream connectivity line MCU. The Cortex-M0 architecture uses the Thumb/Thumb-2 instruction set and is designed for deterministic, low-power real-time control, making the F042 series ideal for USB Type-C accessories, human-interface devices, and small-form-factor sensor nodes. Key features include 32 KB Flash with read-while-write support, 6 KB SRAM with hardware parity, a 12-bit 1 Msps ADC with up to 13 external channels, two 16-bit timers, one 32-bit timer, an independent watchdog, a real-time clock, and a USB 2.0 Full-Speed Device interface with integrated PHY that eliminates the need for an external USB transceiver. The device operates from 2.0V to 3.6V and supports both 2.5V and 3.3V application rails, with multiple low-power modes (Sleep, Stop, Standby) suited to battery-powered products. Architecturally, the STM32F042K6T6 leverages ST's 90 nm embedded Flash process and the Cortex-M0 v6-M core with single-cycle multiplier, achieving 0.93 DMIPS/MHz. The integrated 4-16 MHz HSI oscillator with PLL, plus a 32 kHz LSI for the RTC, allow bill-of-material reduction by removing the external crystal in non-USB applications. The CAN 2.0B interface, combined with USB, makes this part uniquely positioned among Cortex-M0 devices for industrial control and automotive body networks. Typical applications include USB HID peripherals (keyboards, mice, custom HID), USB-to-UART bridges, USB-C audio accessories, CAN node endpoints in industrial networks, small motor control boards, smart-home sensor hubs, and USB-charged IoT endpoints. The 32-pin LQFP footprint is breadboard-friendly and supports hand-rework prototypes while remaining suitable for high-volume SMT assembly. Design consideration: because USB DP/DM pins are bonded to specific GPIO pins (PA11/PA12), designers must avoid remapping these to alternate functions when the USB peripheral is enabled. The integrated pull-up resistor on the DP line is software-controlled, simplifying bus-powered designs. For CAN applications, an external transceiver (e.g., SN65HVD230) is still required because the F042 provides only the protocol controller. This page synthesizes distributor pricing, drop-in same-package alternatives, and design considerations not found in a single datasheet excerpt.

USD $1.84 재고 있음

STM32F051K8T6

STM32F051K8T6 - 48MHz Cortex-M0 MCU 64KB Flash | STMicroelectronics

The STMicroelectronics STM32F051K8T6 is an entry-level 32-bit ARM Cortex-M0 microcontroller from the STM32F0 access line, integrating 64 KB of Flash, 8 KB of SRAM and operating at up to 48 MHz, housed in a 32-pin LQFP (7x7 mm) package. It targets cost-sensitive embedded designs that require the Cortex-M0 instruction set, low power, and a rich set of peripherals in a small footprint. A microcontroller (MCU) is a single-chip computer containing a processor core, program memory, data memory and programmable I/O peripherals. The Cortex-M0 is the most area-optimized member of the ARM Cortex-M family and implements the Thumb/Thumb-2 instruction set, providing deterministic interrupt latency and full binary upward compatibility with higher-end Cortex-M3/M4 parts. STM32F0 MCUs sit in STMicroelectronics' mainstream 32-bit lineup (STM32F0 -> STM32 -> 32-bit MCU -> microcontroller -> semiconductor), serving as a bridge between 8-bit AVR/PIC devices and higher-performance Cortex-M3/M4 families. Key features of the STM32F051K8T6 include: 48 MHz maximum core frequency, 64 KB Flash with hardware single-cycle prefetch, 8 KB SRAM, a 1.2 V internal voltage regulator, multiple low-power modes (Sleep, Stop, Standby), and a fast 12-bit ADC (1 MSPS) with up to 16 channels. Communication peripherals include one I2C, two SPI/second-generation I2S, three USART (one with auto baud, one with modem control), and USB 2.0 full-speed support via the integrated USB-PHY on select device variants. An 8-bit/16-bit timer array, six 16-bit timers, and a 32-bit timer provide flexible PWM, capture/compare and motor-control capability. The architecture uses a von-Neumann bus matrix with separate Flash and SRAM buses, allowing zero-wait-state execution from Flash at 48 MHz when prefetch is enabled. An ultra-low-power RTC, brown-out reset, two watchdogs and a 96-bit unique ID round out the system-level features, all accessible through the standard Cortex-M0 Nested Vectored Interrupt Controller (NVIC). Typical applications include USB peripherals, sensor hubs, low-cost motor control (small BLDC drivers), home appliances, lighting controllers, smart-meter peripherals, battery chargers, wearable devices, and small-completion or industrial control. The integrated USB, multiple timers and ADC channels make it a strong fit for plug-and-play HID peripherals and brushed/brushless DC drive stages. Design considerations: connect the NRST pin to a 100 nF capacitor + 10 kΩ pull-up for clean reset; place a 100 nF decoupling cap on each VDD pin and a 4.7 µF bulk cap near the regulator output; route the HSE/LSE crystal traces short and guard the analog AVDD pin with a ferrite bead if the ADC is used for precise measurements. This page synthesises distributor pricing, drop-in alternatives and practical design notes not found in the manufacturer datasheet, and is maintained against the ST RM0376 reference manual.

USD $1.42 재고 있음

STM32F051R8T6

STM32F051R8T6 - 48MHz Cortex-M0 MCU, 64KB Flash | ST

The STMicroelectronics STM32F051R8T6 is a 32-bit ARM Cortex-M0 microcontroller operating at up to 48 MHz with 64 KB of embedded Flash memory and 8 KB of SRAM, housed in a 64-pin LQFP surface-mount package. A microcontroller (MCU) integrates a processor core, non-volatile memory, SRAM, and a rich set of peripherals onto a single silicon die, forming the lowest tier of the computing hierarchy: transistor -> logic gate -> processor core -> microcontroller -> embedded system. Within STMicroelectronics' portfolio, the STM32F0 entry-level series sits below the mainstream STM32F1/F4 families and provides Cortex-M0 cost efficiency while retaining STM32 tooling, peripheral architecture, and software ecosystem compatibility. Key features of the STM32F051R8T6 include 11 timers covering basic, general-purpose, and advanced (motor-control) functions, a 12-bit 1 Msps ADC, a 12-bit DAC, up to 55 GPIO lines, and communication interfaces spanning USART, SPI, I2C, and CEC. A CRC calculation unit, programmable watchdogs, and POR/PDR reset circuitry improve design robustness. Supply voltage spans 2.0V to 3.6V, simplifying integration into battery- and USB-adjacent designs. Technically, the Cortex-M0 core executes Thumb instruction subset code with a 32-bit datapath and a nested vectored interrupt controller (NVIC) delivering deterministic low-latency interrupts. The embedded Flash supports in-system programming via USART, while the flexible clock tree accepts an internal 8 MHz HSI or external crystal sources up to 48 MHz system frequency. Typical applications include industrial automation sensors and actuators, consumer appliances, motor control with the advanced timers, IoT sensor nodes, and system auxiliary control functions. Designers should budget SRAM carefully: 8 KB is ample for bare-metal control loops but limits large buffers or complex stacks; enable hardware CRC and DMA offload to free CPU cycles. This page adds value beyond the manufacturer datasheet by consolidating verified distributor specifications, drop-in alternatives, cross-brand substitution guidance, and practical design notes for the STM32F051R8T6.

USD $2.45 재고 있음

STM32F070CBT6

STM32F070CBT6 - ARM Cortex-M0 MCU 128KB Flash | STMicroelectronics

The STMicroelectronics STM32F070CBT6 is a 32-bit ARM Cortex-M0 microcontroller from the STM32F0 series, offering 128KB of Flash memory and 16KB of SRAM in a 48-pin LQFP package. It operates at a core frequency of up to 48 MHz and supports a supply voltage range of 2.4V to 3.6V. Data verified as of 2026-08-05. What is a microcontroller? A microcontroller (MCU) is a compact integrated circuit designed to govern a specific operation in an embedded system. It integrates a processor core, memory (Flash and SRAM), and programmable input/output peripherals on a single chip. The STM32F070CBT6 belongs to the STM32F0 series, which is part of the broader STM32 family of 32-bit ARM Cortex-M microcontrollers. This hierarchy places it within the ARM Cortex-M0 category, a low-power, entry-level core optimized for cost-sensitive applications. Key features include a 12-bit ADC with up to 16 channels, multiple communication interfaces (I2C, SPI, USART), and a variety of timers including advanced-control timers. The device also includes a DMA controller, an RTC, and a CRC calculation unit. The LQFP-48 package provides a compact footprint suitable for space-constrained designs while offering sufficient I/O pins for peripheral connectivity. The STM32F070CBT6 is built on a 32-bit ARM Cortex-M0 core with a Harvard architecture, achieving 1.25 DMIPS/MHz. It includes a nested vectored interrupt controller (NVIC) for efficient interrupt handling and supports both low-power modes (Sleep, Stop, Standby) to optimize energy consumption. The device is designed for a wide range of embedded applications requiring a balance of performance, power efficiency, and cost. Typical applications include industrial control systems, consumer electronics, IoT devices, and home automation. Its rich peripheral set and low-power capabilities make it suitable for sensor interfacing, motor control, and communication protocols. The wide operating temperature range (-40°C to +85°C) ensures reliability in harsh environments. When designing with this MCU, ensure proper decoupling of the power supply pins and consider the use of an external crystal for accurate timing. The device supports in-circuit programming and debugging via SWD, facilitating firmware development and updates. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the STMicroelectronics datasheet, providing engineers with a comprehensive resource for selection and implementation.

USD $1.57 재고 있음

STM32F071CBT7

STM32F071CBT7 - 48MHz Cortex-M0 MCU, 128KB Flash | STMicroelectronics

The STMicroelectronics STM32F071CBT7 is an Arm Cortex-M0 32-bit RISC microcontroller operating at up to 48 MHz, integrating 128 KB of Flash memory and 16 KB of SRAM with hardware parity in a 48-pin LQFP (7x7 mm) package. It is part of the STM32F0 "Access Line" mainstream family and includes a Consumer Electronics Control (CEC) peripheral alongside 12-bit ADC, 12-bit DAC, and 12 timers, all within a 2.0V-3.6V digital supply range. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash for code and SRAM for data), digital peripherals (timers, communication interfaces, GPIO) and analog peripherals (ADC, DAC, comparators) onto one silicon die. The Arm Cortex-M0 is the smallest and most energy-efficient member of the Cortex-M family, designed for deterministic real-time control at low cost and low active current; it implements the Thumb-2 instruction subset and the NVIC (Nested Vectored Interrupt Controller). Within the broader taxonomy, the STM32F071 sits below Cortex-M3/M4/M7 parts in processing performance, but above 8-bit MCUs (8051, AVR, PIC16) in code density, debug tooling, and peripherals - making it the typical "mainstream" choice for cost-sensitive embedded designs. Key differentiating features include: hardware parity-checked SRAM for higher reliability in safety-relevant code, a 32-bit hardware CRC calculation unit (offloading software CRC loops), an integrated HDMI CEC controller for consumer-electronics interoperability, and a 5V-tolerant I/O structure that simplifies interfacing with legacy 5V logic. The 12-bit ADC and 12-bit DAC are 1 MSPS and 1 MSPS respectively, allowing mixed-signal control loops without external converters. Architecture: Cortex-M0 core with single-cycle multiplier, 3-stage pipeline, and SysTick timer; the bus matrix splits I-code, D-code, and system buses to allow parallel Flash fetch and SRAM access. Power management integrates a low-power Run, Sleep, Stop, and Standby modes with RTC retention, and a brown-out reset (BOR) plus a power-on reset (POR) supervisor. Typical applications include USB-CDC virtual COM ports (using the on-chip USB FS device PHY-less with external 1.5 k pull-up), home-appliance control panels, motor-control sub-modules, HDMI-CEC-equipped TV and set-top boxes, and low-cost sensor hubs. The package, 48-LQFP, is a hand-solderable and prototype-friendly footprint that integrates well into both production and hobby boards. Design consideration: the 7 suffixes (T7 = LQFP48 industrial temperature grade, tape-and-reel) require careful selection when migrating between similar STM32F0 part numbers - the operating temperature range, package, and shipping form all vary by suffix. Designers should verify that the target application does not exceed -40C to +85C industrial range. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and design notes sourced from the STMicroelectronics datasheet (DS9826), which go beyond what the manufacturer PDF alone offers for procurement and second-sourcing decisions.

USD $2.95 재고 있음

STM32F072C8T6

STM32F072C8T6 - 48MHz 64KB Cortex-M0 MCU | STMicroelectronics

The STMicroelectronics STM32F072C8T6 is a 32-bit ARM Cortex-M0 microcontroller operating up to 48 MHz, with 64 KB of Flash memory and a 48-LQFP 7 x 7 mm package. It belongs to the STM32F0 microcontroller family and is positioned for compact USB, CAN, general embedded-control, and low-power embedded applications. The supplied distributor information identifies the device as a mainstream ARM Cortex-M0 MCU with USB and CAN connectivity. The STM32F0 family consists of entry-level 32-bit RISC microcontrollers intended to provide efficient control processing, integrated communications, analog peripherals, and flexible memory options in a small surface-mount package. This hierarchy places the STM32F072C8T6 within the broader category of embedded microcontrollers, where the device executes firmware, controls peripherals, and communicates with external hardware. Verified source data identifies a 48 MHz maximum CPU frequency, 64 KB of Flash, and a 48-LQFP package. The distributor descriptions also identify USB and CAN support as defining connectivity features. The 48-pin LQFP format provides a conventional leaded surface-mount footprint suitable for designs requiring accessible pins, compact board area, and straightforward assembly. Exact RAM size, voltage limits, peripheral details, and temperature limits are not supplied in the verified excerpts and are therefore not inferred here. Because the device is an ARM Cortex-M0 microcontroller, software development can use the STM32 family ecosystem and embedded C toolchains. The Cortex-M0 core provides a 32-bit RISC architecture, while the STM32F072x8/xB family description from STMicroelectronics emphasizes high-performance embedded control and integrated peripherals. Toolchain and exact peripheral assignments should be confirmed against the manufacturer datasheet and reference manual for the selected board design. Typical application areas include USB-connected control devices, CAN-connected industrial or automotive interface modules, compact sensor controllers, embedded instrumentation, and general-purpose 48 MHz embedded products. USB and CAN are especially relevant where a controller must combine local real-time processing with a standardized communications link. Designers should verify package pin assignments, power requirements, clock configuration, decoupling, and peripheral availability against the official STM32F072C8T6 documentation before layout release. The verified data confirms the 48-LQFP 7 x 7 mm package and 48 MHz Cortex-M0 performance, but does not provide a verified pinout, recommended capacitor values, or full electrical limits. This product record combines distributor availability information, manufacturer family positioning, interface requirements, package data, and practical selection guidance to support initial design decisions. It is intended to help engineers identify whether the STM32F072C8T6 matches the required microcontroller package, processing speed, Flash capacity, and USB/CAN feature set.

USD $5.44 재고 있음

STM32F072C8T6TR

STM32F072C8T6TR - 48MHz 64KB Cortex-M0 MCU | STMicroelectronics (Tape & Reel)

The STMicroelectronics STM32F072C8T6TR is a 32-bit ARM Cortex-M0 microcontroller operating up to 48 MHz, with 64 KB of Flash memory and a 48-LQFP 7 x 7 mm package. It belongs to the STM32F0 microcontroller family and is positioned for compact USB, CAN, general embedded-control, and low-power embedded applications. The supplied distributor information identifies the device as a mainstream ARM Cortex-M0 MCU with USB and CAN connectivity. The STM32F0 family consists of entry-level 32-bit RISC microcontrollers intended to provide efficient control processing, integrated communications, analog peripherals, and flexible memory options in a small surface-mount package. This hierarchy places the STM32F072C8T6TR within the broader category of embedded microcontrollers, where the device executes firmware, controls peripherals, and communicates with external hardware. Verified source data identifies a 48 MHz maximum CPU frequency, 64 KB of Flash, and a 48-LQFP package. The distributor descriptions also identify USB and CAN support as defining connectivity features. The 48-pin LQFP format provides a conventional leaded surface-mount footprint suitable for designs requiring accessible pins, compact board area, and straightforward assembly. Exact RAM size, voltage limits, peripheral details, and temperature limits are not supplied in the verified excerpts and are therefore not inferred here. Because the device is an ARM Cortex-M0 microcontroller, software development can use the STM32 family ecosystem and embedded C toolchains. The Cortex-M0 core provides a 32-bit RISC architecture, while the STM32F072x8/xB family description from STMicroelectronics emphasizes high-performance embedded control and integrated peripherals. Toolchain and exact peripheral assignments should be confirmed against the manufacturer datasheet and reference manual for the selected board design. Typical application areas include USB-connected control devices, CAN-connected industrial or automotive interface modules, compact sensor controllers, embedded instrumentation, and general-purpose 48 MHz embedded products. USB and CAN are especially relevant where a controller must combine local real-time processing with a standardized communications link. Designers should verify package pin assignments, power requirements, clock configuration, decoupling, and peripheral availability against the official STM32F072C8T6TR documentation before layout release. The verified data confirms the 48-LQFP 7 x 7 mm package and 48 MHz Cortex-M0 performance, but does not provide a verified pinout, recommended capacitor values, or full electrical limits. This product record combines distributor availability information, manufacturer family positioning, interface requirements, package data, and practical selection guidance to support initial design decisions. It is intended to help engineers identify whether the STM32F072C8T6TR matches the required microcontroller package, processing speed, Flash capacity, and USB/CAN feature set.