STM32F030F4P6 - 48MHz Cortex-M0 16KB MCU | STMicroelectronics
부품 번호: STM32F030F4P6 ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $0.5768 | $0.58 |
| 10 | $0.6314 | $6.31 |
| 100 | $0.6314 | $63.14 |
| 500 | $0.6314 | $315.70 |
| 1,000 | $0.6314 | $631.40 |
| 3,000 | $0.6314 | $1,894.20 |
STM32F030F4P6 개요
A microcontroller is a semiconductor device that integrates a processor core, memory, and peripherals into one embedded-control platform. In the hierarchy, the STM32F030F4P6 is an Arm Cortex-M0 microcontroller, an embedded processor, and a member of the STM32F0 family. The STM32F0 series combines a compact general-purpose architecture with timers, communication interfaces, and analog conversion functions for small control systems.
The verified data identifies a high-performance 32-bit RISC core operating at 48 MHz, 16 KB Flash organized as 16K x 8, and 4 KB SRAM according to the distributor and datasheet search results. The device also includes 12-bit and 15-bit ADC capability as stated in the LCSC result, while the manufacturer page identifies enhanced peripherals and I/O resources. Power-on reset and power-down reset functionality is identified in the DigiChip result.
The STM32F030F4P6 is appropriate for compact embedded systems where cost, simplicity, and low pin count matter more than high-speed connectivity or large memory capacity. Its Arm Cortex-M0 instruction set supports deterministic embedded control, while the 48 MHz clock provides a practical balance between processing capability and power efficiency. The 20-pin TSSOP package enables compact PCB layouts while supporting external peripherals and signal inputs.
Typical uses include low-cost sensor nodes, simple industrial controllers, compact motor-control stages, digital meters, and connected IoT devices. Designers must ensure that the selected firmware, clock tree, peripherals, and board-level support devices match the STM32F030x4 device requirements. The exact pin function, electrical limits, peripheral configuration, and package dimensions should be confirmed against the STMicroelectronics datasheet.
For a new design, the 48 MHz Cortex-M0 core and 16 KB Flash make the STM32F030F4P6 most suitable for small control loops and auxiliary processing rather than complex graphical or high-bandwidth workloads. The TSSOP-20 package also requires careful PCB escape routing and adequate pin-copper clearance during assembly.
This page combines verified manufacturer and distributor information, source links, package details, engineering use cases, and replacement considerations to support component selection and sourcing. Because the supplied data does not include a complete verified pin table or all peripheral electrical limits, those fields are intentionally not guessed.
드롭인 대체품: STM32F030F4P6 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: STM32F030F4P6 (동일 폼 팩터 및 풋프린트) — 차이점: Core Architecture, Flash Memory, Package.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
HK32F030F4P6
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
STM32F030F4P6 최대 정격 & 전기적 특성
| Core | Arm Cortex-M0 32-bit RISC |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 16 KB (16K x 8) |
| SRAM | 4 KB |
| Operating Voltage Range | 2.4 V to 3.6 V |
| Architecture | Arm-based 32-bit RISC |
| ADC Resolution | 12-bit and 15-bit |
| 패키지 | 20-pin TSSOP |
| 실장 유형 | Surface Mount |
| Product Family | STM32F0 value-line series |
| Embedded Control Role | Industrial control, IoT, metering, and motor-control applications |
| Power-On Reset | POR |
| Power-Down Reset | PDR |
| Peripheral Resources | Timers, ADC, communication interfaces, and enhanced I/O |
| Memory Organization | 16K x 8 Flash organization |
| Core Architecture | Arm Cortex-M0 |
| Datasheet Family Coverage | STM32F030x4, STM32F030x6, STM32F030x8, and STM32F030xC |
STM32F030F4P6 20-pin tssop 핀 구성 가이드
STM32F030F4P6(20-pin tssop 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: STM32F030F4P6.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
STM32F030F4P6 적합 용도: 6 애플리케이션s: Compact Industrial Control, Low-Cost IoT Sensor Node, Digital Metering, Simple Motor-Control Interface, Compact Control Board, Embedded Automation Module.
Compact Industrial Control
The STM32F030F4P6 fits compact industrial-control tasks because its Arm Cortex-M0 core operates at up to 48 MHz and the device provides 16 KB Flash, 4 KB SRAM, timers, and ADC capability. It can execute sequencing, monitor analog inputs, and coordinate relays or actuators from a 2.4 V to 3.6 V supply. The 20-pin TSSOP footprint helps keep controller boards compact, while the integrated RISC core reduces the need for external processing. The primary design trade-off is limited memory and peripheral bandwidth, so complex logging or high-speed closed-loop control should be validated against the datasheet.
추천
Low-Cost IoT Sensor Node
The STM32F030F4P6 is suitable for a small IoT sensor node that samples an analog signal, applies basic conditioning, and formats data for a serial communications peripheral. Its 48 MHz Cortex-M0 core provides enough control performance for local filtering and state-machine tasks, while 4 KB SRAM supports short working buffers and 16 KB Flash accommodates compact firmware. Operation from 2.4 V to 3.6 V aligns with many low-voltage embedded rails. Designers should confirm the exact ADC channels, communication peripherals, and low-power modes in the manufacturer documentation before selecting the part for battery operation.
추천
Digital Metering
The STM32F030F4P6 can serve as the control MCU in a digital meter that acquires sensor inputs, performs scaling and calibration, drives a display, and manages keypad or serial output. Its verified 12-bit and 15-bit ADC capability provides a basis for measurement-oriented designs, while the 48 MHz core handles acquisition sequencing and control logic. The 2.4 V to 3.6 V range is useful for compact measurement equipment. Accuracy depends on the analog front end, reference design, layout, and calibration strategy; those parameters are not fully specified in the supplied data and must be checked against the datasheet.
추천
Simple Motor-Control Interface
The STM32F030F4P6 is appropriate for small motor-control interfaces that use timers and GPIO outputs to generate control signals, read feedback, and supervise system state. The 48 MHz Arm Cortex-M0 core provides deterministic embedded execution, while the ADC capability can support current, position, or analog feedback monitoring. The 20-pin TSSOP package is useful when the controller must fit close to a driver circuit. This application requires careful validation of timer mapping, pin alternate functions, electrical limits, and firmware timing because the supplied search results do not provide the complete timer and pin assignment tables.
추천
Compact Control Board
The STM32F030F4P6 supports compact control boards that combine sensor inputs, simple actuator outputs, and a low-cost Arm-based firmware platform. Its 16 KB Flash and 4 KB SRAM are sufficient for small control applications, and the 2.4 V to 3.6 V operating range simplifies integration with conventional embedded power rails. The TSSOP-20 package offers a small surface-mount solution but requires careful escape routing and assembly planning. Because the supplied data does not state exact GPIO counts, package dimensions, or thermal parameters, those details must be confirmed from official STMicroelectronics documentation.
추천
Embedded Automation Module
The STM32F030F4P6 can act as the local controller in an embedded automation module that coordinates digital inputs, outputs, timing functions, and simple analog measurements. The Cortex-M0 architecture provides a straightforward 32-bit platform for state machines and deterministic control loops, while timers and communication interfaces support common automation tasks. Its compact TSSOP-20 package is advantageous when the module must fit into a small enclosure. Firmware portability and peripheral equivalence should be verified for any migration, especially because similar MCU families may use different peripheral registers, interrupt mappings, or clock configurations.
추천
추천 제품 요약
엔지니어링 참조 데이터: STM32F030F4P6 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | HK32F030F4P6 |
|---|---|---|
| Package | 20-pin TSSOP | 20-pin TSSOP |
| Brand | STMicroelectronics | GigaDevice |
| Firmware Compatibility | STMicroelectronics STM32F0 firmware ecosystem | Hardware and software compatibility claimed; firmware validation required |
주요 차별점
- Verified STMicroelectronics family positioning (vs HK32F030F4P6)
- Defined target memory configuration (vs HK32F030F4P6)
- Defined target clock and supply (vs HK32F030F4P6)
- Package-level commonality (vs HK32F030F4P6)
설계 노트
Place the STM32F030F4P6 power and decoupling connections directly between the appropriate supply and ground pins, following the exact package and pinout in the STMicroelectronics datasheet. Keep the 20-pin TSSOP escape routes short and provide adequate ground-plane continuity around the device. Because the supplied snippets do not provide a complete pin table, do not infer alternate functions or pad locations from package count alone.
Do not treat a same-package MCU as a guaranteed drop-in replacement. The verified HK32F030F4P6 result specifically describes a pin-compatible engineering-review candidate that may require firmware work. Before replacing STM32F030F4P6, compare power pins, reset behavior, oscillator connections, ADC channels, timer mappings, interrupt vectors, bootloader support, and peripheral register compatibility using the manufacturer documentation.
Design the 2.4 V to 3.6 V supply with sufficient stability margin and verify the current requirements of the selected external peripherals. Use local decoupling close to the MCU supply pins and keep analog and digital return currents separated where practical. The supplied data does not provide regulator current limits or package thermal resistance, so supply sizing and thermal validation must use the official electrical characteristics.
For ADC-based metering or sensor nodes, route analog inputs away from fast switching nodes and clocks, use a continuous ground reference, and follow the datasheet recommendations for analog grounding. The reported 12-bit and 15-bit ADC capability does not determine measurement accuracy by itself; accuracy also depends on source impedance, sampling time, reference stability, calibration, layout, and noise filtering.
규정 준수 정보
The supplied verified data does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status for STM32F030F4P6.
