집적 회로

하위 카테고리

📁 ADC/DAC 2,700+ 제품 📁 증폭기 IC 1,100+ 제품 📁 오디오 코덱 18 제품 📁 오디오 IC 2 제품 📁 클록 및 타이밍 470+ 제품 📁 DSP 1,000+ 제품 📁 데이터 수집 IC 2 제품 📁 디지털 포텐셔미터 4 제품 📁 디스플레이 드라이버 및 컨트롤러 1 제품 📁 FPGA & CPLD 6,800+ 제품 📁 인터페이스 IC 2,200+ 제품 📁 LED 드라이버 1 제품 📁 로직 IC 360+ 제품 📁 메모리 IC 870+ 제품 📁 마이크로컨트롤러 19,000+ 제품 📁 마이크로프로세서 4 제품 📁 모터 드라이버 1 제품 📁 기타 1 제품 📁 Sensor and Detector Interfaces 1 제품 📁 특수 IC 15 제품 📁 비디오 IC 13 제품

제품 (35,000+)

ATMEGA16M1-15MD - 16KB Flash AVR MCU with CAN/LIN | Microchip
ATMEGA16M1-15MD

ATMEGA16M1-15MD - 16KB Flash AVR MCU with CAN/LIN | Microchip

The Microchip Technology ATMEGA16M1-15MD is an 8-bit AVR microcontroller with 16 KB self-programming Flash program memory, 1 KB SRAM, and 512 B EEPROM, housed in a 32-pin QFN package rated for operation from -40C to +150C in automotive-grade environments. Per Microchip product data, it integrates a CAN controller with six message objects, a LIN controller, a Power Stage Controller (PSC), and an 8-channel 10-bit ADC, along with a JTAG interface for on-chip debugging. An 8-bit microcontroller (MCU) is a single-chip computer that executes a stored program to control electronic systems. Within the semiconductor hierarchy, the ATMEGA16M1 sits in the AVR family of reduced instruction set computing (RISC) devices, which fall under the broader classes of embedded processors and system-on-chip solutions. The AVR advanced RISC architecture executes 133 powerful instructions, most in a single clock cycle, delivering efficient performance at modest clock rates. Key differentiating features include the supply range of 2.7 V to 5.5 V, 53 general-purpose I/O lines on the family, 8 MHz rated clock operation in this speed grade, and the combination of CAN and LIN networking controllers on one die - a rare pairing that makes this family well suited to in-vehicle networking nodes. The 10-bit ADC supports single-ended conversion with operation specified from -40C to +150C at VCC = 4.5 V to 5.5 V. Architecturally, the device uses a Harvard-structure AVR core with separate program and data buses, self-programming Flash for field updates, and a Power Stage Controller for motor-control PWM generation. The JTAG boundary-scan and on-chip-debug capability shortens development cycles. Typical applications include automotive body and LIN sub-network nodes, CAN-based ECU modules, motor control with the PSC, and sensor interfaces using the 8-channel 10-bit ADC. Designers should verify CAN/LIN transceivers externally, since the controllers provide the protocol logic only. When selecting between speed grades, the -15 suffix denotes the 150C-rated automotive temperature class; the same die is offered in TQFP for cost-sensitive builds. This page synthesizes distributor stock data, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

견적 요청 문의하기
ATMEGA16M1-15MZ - 16KB Flash CAN/LIN AVR MCU 16MHz | Microchip
ATMEGA16M1-15MZ

ATMEGA16M1-15MZ - 16KB Flash CAN/LIN AVR MCU 16MHz | Microchip

The Microchip Technology ATMEGA16M1-15MZ is an 8-bit AVR RISC microcontroller with 16 KB self-programming Flash, 1 KB SRAM, and 512 B EEPROM, integrating a CAN controller with six message objects, a LIN controller, a Power Stage Controller (PSC), and an 8-channel 10-bit ADC, clocked at up to 16 MHz in a 32-pin VQFN exposed-pad (7x7 mm) package. An 8-bit AVR microcontroller is a Harvard-architecture RISC processor in the broader microcontroller (MCU) hierarchy of embedded processors, combining program memory, data memory, peripherals, and a CPU core on a single die. The AVR family executes most of its 131 instructions in a single clock cycle, delivering roughly 16 MIPS at 16 MHz, which places it among the efficient 8-bit MCUs for real-time embedded control. Key differentiating features of the ATMEGA16M1 include its on-chip CAN 2.0A/B controller with six message objects, its LIN 2.1-compliant controller, and the Power Stage Controller, which generates three complementary PWM outputs with dead-time insertion and fault protection. The 8-channel 10-bit ADC and internal oscillator reduce external component count, while the JTAG interface enables on-chip debugging and boundary-scan programming. Architecturally, the device uses the advanced AVR RISC core with 32 general-purpose registers directly connected to the ALU, allowing two independent registers to be accessed in one instruction. Self-programming Flash supports in-system and boot-code updates, and the automotive-grade qualification (AEC-Q100 family designation) supports -40C to +125C operation for the 15-speed automotive grade. Typical applications include automotive body and HVAC control nodes, LIN/CAN gateway sub-nodes, BLDC and stepper motor control via the PSC, and industrial sensor modules where the 10-bit ADC and CAN bus are used together. A key design consideration is supply voltage: the device operates from 2.7 V to 5.5 V, but Flash write operations and maximum clock speed should be verified against the datasheet voltage-versus-frequency derating curves before fixing the system clock. This page synthesizes distributor pricing and stock signals, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet alone.

견적 요청 문의하기
ATMEGA16M1-AU - AVR MCU 16MHz, CAN+LIN, TQFP-32 | Microchip
ATMEGA16M1-AU

ATMEGA16M1-AU - AVR MCU 16MHz, CAN+LIN, TQFP-32 | Microchip

The Microchip Technology ATMEGA16M1-AU is an 8-bit AVR microcontroller with 16 KB self-programming Flash, 1 KB SRAM, 512 B EEPROM, an integrated CAN 2.0A/B controller with six message objects, a LIN controller, and a Power Stage Controller (PSC), running at up to 16 MHz in a 32-pin TQFP (7 x 7 mm) package. An 8-bit AVR microcontroller is a Reduced Instruction Set Computing (RISC) processor belonging to the broader microcontroller hierarchy: MCU -> embedded processor -> integrated circuit. AVR cores execute most of their 133 powerful instructions in a single clock cycle, and the ATmega family adds embedded flash program memory, SRAM, EEPROM, and mixed-signal peripherals on one die, replacing multi-chip solutions. Key features include a high-performance low-power AVR advanced RISC architecture with 32 x 8 general purpose working registers, an 8-channel 10-bit ADC, JTAG (IEEE boundary-scan and on-chip-debug) for in-system development, and self-programming flash enabling field firmware updates. The combined CAN and LIN controllers make the M1 family unique: CAN targets vehicle networking nodes, while LIN covers low-cost auxiliary buses. The differentiating block is the Power Stage Controller (PSC), a multi-channel, high-precision PWM peripheral with dead-time insertion and fault protection designed for motor control and power-conversion applications such as BLDC, brushed DC, and dimming ballasts. Typical applications include automotive body and HVAC control nodes, LIN/CAN gateway sub-nodes, BLDC and brushed-DC motor drives, and industrial actuator control. Design consideration: the device operates from a 2.7 V to 5.5 V supply; use a clean 5 V rail with 100 nF decoupling per VCC/AVCC pair, and reserve the JTAG header on the PCB for on-chip debugging. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기
ATMEGA16M1-MU - 8-bit AVR MCU, CAN, 16KB Flash | Microchip
ATMEGA16M1-MU

ATMEGA16M1-MU - 8-bit AVR MCU, CAN, 16KB Flash | Microchip

The Microchip Technology ATMEGA16M1-MU is an 8-bit AVR microcontroller with 16 KB self-programming Flash, 1 KB SRAM, 512 B EEPROM, an integrated CAN controller with six message objects, a LIN controller, and a Power Stage Controller (PSC), housed in a 32-pin QFN (7x7 mm) exposed-pad package operating at up to 16 MHz. A microcontroller unit (MCU) is a single-chip computer that integrates a processor core, memory, and peripherals into one package, sitting at the lowest level of the embedded systems hierarchy: MCU -> embedded processor -> system-on-chip -> complete electronic system. The AVR family uses a modified Harvard RISC architecture in which most of its 133 powerful instructions execute in a single clock cycle, giving high code density and deterministic performance for real-time embedded control. Key features of the ATMEGA16M1-MU include the on-chip CAN 2.0A/B controller with six message objects for automotive and industrial networking, a LIN 2.1 controller for low-cost vehicle subnetworks, and a PSC that generates complementary PWM outputs with dead-time insertion - ideal for motor control and lighting ballasts. The 8-channel 10-bit ADC supports sensor acquisition, and the JTAG interface enables on-chip debug and boundary-scan programming. The device operates from a 2.7 V to 5.5 V supply, covering both 3.3 V and 5 V systems. Technically, the self-programming Flash allows in-system firmware updates via bootloaders, while the AVR core delivers up to 16 MIPS at 16 MHz. The exposed-pad QFN-32 package provides good thermal and electrical performance for compact designs. Typical applications include automotive body and LIN/CAN gateway nodes, BLDC and PMSM motor control using the PSC, and industrial automation sensors and actuators that benefit from the robust CAN interface. Design consideration: the QFN exposed pad must be soldered to a grounded copper pour for reliable operation and optimal ADC noise performance; verify CAN transceiver compatibility when designing the physical layer. This page synthesizes verified distributor pricing, drop-in family alternatives, comparison tables, and practical design notes not found in the manufacturer datasheet, giving engineers a complete selection resource in one place.

견적 요청 문의하기
ATMEGA16U2-AU - 8-bit AVR USB MCU 16KB Flash 16MHz TQFP-32 | Microchip
ATMEGA16U2-AU

ATMEGA16U2-AU - 8-bit AVR USB MCU 16KB Flash 16MHz TQFP-32 | Microchip

The Microchip Technology ATMEGA16U2-AU is an 8-bit AVR RISC USB microcontroller combining 16 KB ISP flash memory, 512 B EEPROM, 512 B SRAM and a full-speed USB 2.0 device controller in a 32-pin TQFP (7x7 mm) package, executing at up to 16 MHz. An 8-bit AVR microcontroller is a Harvard-architecture RISC processor from the AVR family (now owned by Microchip Technology after its acquisition of Atmel). AVR MCUs execute most instructions in a single clock cycle, sit in the broader hierarchy of microcontroller units (MCU) under embedded processors, and integrate flash program memory, SRAM, EEPROM data storage, timers, USART, SPI, TWI and general purpose I/O on a single die. Key features of the ATMEGA16U2-AU include 16 KB of self-programmable ISP flash with read-while-write support, a built-in full-speed USB controller with device mode (no external USB transceiver required), 22 general purpose I/O lines, two flexible 8-bit and 16-bit timer/counters, and a USART with SPI-compatible mode for USB-to-serial bridging. The AVR enhanced RISC core executes powerful instructions mostly in one cycle, delivering near-1 MIPS per MHz throughput at 16 MHz. Architecturally, the device uses 32 general purpose working registers directly connected to the ALU, allowing two independent registers to be accessed in one instruction. Hardware support includes power-on reset, brown-out detection, internal 8 MHz calibrated RC oscillator, watchdog timer, and three sleep modes (Idle, Power-down, Standby) for low-power designs. Typical applications include USB-to-serial conversion on Arduino Uno R3 and Mega 2560 R3 boards (where it bridges USB to the ATmega328P/2560 UART), USB HID devices such as keyboards, mice and game controllers, and USB CDC virtual-COM-port adapters. A key design consideration: at 16 MHz the flash is rated for a maximum of 4.5 V operation (2.7 V for 8 MHz), so always pair the supply voltage with clock speed, and tie the /HWB pin appropriately so the on-chip DFU bootloader is entered only when needed. This page synthesizes distributor pricing, drop-in same-footprint alternatives, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기
ATMEGA16U2-AUR - 8-bit AVR USB MCU 16KB 16MHz TQFP-32 | Microchip
ATMEGA16U2-AUR

ATMEGA16U2-AUR - 8-bit AVR USB MCU 16KB 16MHz TQFP-32 | Microchip

The Microchip Technology ATMEGA16U2-AUR is an 8-bit AVR RISC microcontroller with an integrated full-speed USB 2.0 device controller, delivering 16 KB of ISP FLASH memory, 512 B of EEPROM, and 512 B of SRAM at up to 16 MHz in a 32-pin TQFP (7x7 mm) package. An 8-bit AVR microcontroller is a reduced-instruction-set (RISC) processor in the broader microcontroller hierarchy (MCU -> embedded processor -> integrated circuit) that executes most instructions in a single clock cycle. The ATmega16U2 belongs to the AVR USB subfamily, in which a hardware USB controller with 32-byte endpoint FIFOs is paired with the classic AVR core, eliminating the need for an external USB-to-serial bridge chip in many designs. Key features include 16 KB of self-programmable FLASH with read-while-write support, 22 general-purpose I/O lines, 32 general-purpose working registers, two flexible timer/counters with compare modes, a 10-bit ADC, a USART with hardware flow control (RTS/CTS), and an on-chip debug interface. The integrated USB controller supports device operation at full speed (12 Mbps) and enables USB bootloader firmware such as that used on the Arduino UNO R3 USB interface. Technically, the AVR core achieves close to 1 MIPS per MHz, allowing the ATMEGA16U2-AUR to run the USB stack and application logic at 16 MHz from a 5 V supply (4.5 V to 5.5 V); operation down to 2.7 V is supported at reduced 8 MHz clocking. The device is in-system programmable via SPI, USB, or a parallel programmer, simplifying field updates. Typical applications include USB-to-UART bridge functions on development boards (notably the Arduino UNO and Mega 2560), custom USB HID devices such as keyboards and game controllers, USB-powered industrial control nodes, and general embedded control where a USB device port is required. Designers should note the supply-voltage constraint: full 16 MHz operation requires a 4.5 V to 5.5 V rail, while battery-powered designs must either drop to 8 MHz at lower voltage or select the L-grade variant. This page adds value beyond the datasheet by consolidating distributor pricing, drop-in family alternatives, design notes, and comparison tables not found on the manufacturer product page.

견적 요청 문의하기
ATMEGA16U2-MU - 16MHz AVR USB MCU 16KB Flash | Microchip
ATMEGA16U2-MU

ATMEGA16U2-MU - 16MHz AVR USB MCU 16KB Flash | Microchip

The Microchip Technology ATMEGA16U2-MU is an 8-bit AVR RISC microcontroller with an integrated full-speed USB 2.0 controller, delivering 16 MHz maximum clock frequency, 16 KB ISP flash memory, and 22 general-purpose I/O lines in a 32-pin VQFN (5x5 mm) package. An AVR microcontroller is a modified-Harvard-architecture 8-bit RISC processor in which flash program memory, SRAM data memory, and EEPROM are accessed through separate address spaces, allowing most instructions to execute in a single clock cycle. Within the power-management hierarchy, a USB AVR such as the ATmega16U2 combines a general-purpose MCU core with a dedicated USB device controller, replacing a separate USB-to-serial bridge chip in many designs. Key features include 16 KB of read-while-write ISP flash, 512 B EEPROM, 512 B SRAM, 32 general-purpose working registers, two flexible timer/counters with compare modes, a 10-bit ADC, and an on-chip USB controller with 25 MHz capable PLL. The 16 MHz operation at 2.7 V to 5.5 V supply makes the device tolerant of 3.3 V and 5 V USB domains. The core executes 133 powerful instructions, most in a single clock cycle, giving throughput close to 16 MIPS at 16 MHz. The USB interface supports full-speed 12 Mbps operation and can be used for USB-to-serial conversion or HID device emulation under firmware such as LUFA. Typical applications include USB-to-serial interface MCUs (notably as the USB bridge on the Arduino Uno R3), HID keyboards and mice, and small embedded control nodes with USB firmware update capability. A key design consideration is the UCAP pin: a 1 uF capacitor on the USB internal regulator output is required when operating from 3.3 V, and correct 22 ohm series termination on D+/D- improves signal integrity. This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기
ATMEGA16U4-AU - 8-Bit AVR MCU 16KB Flash USB 16MHz | Microchip
ATMEGA16U4-AU

ATMEGA16U4-AU - 8-Bit AVR MCU 16KB Flash USB 16MHz | Microchip

The Microchip Technology ATMEGA16U4-AU is an 8-bit AVR RISC microcontroller with 16KB ISP Flash (8KB boot section), 1024B EEPROM, 2.5KB SRAM, and an integrated USB 2.0 full-speed/low-speed device controller, executing at up to 16 MHz in a 44-pin TQFP (10x10 mm) package. An 8-bit AVR microcontroller is a Harvard-architecture processor that executes most of its 133 instructions in a single clock cycle, combining a general-purpose MCU core with on-chip program Flash and peripherals. Within the power-management hierarchy, it sits as a complete embedded system-on-chip: CPU plus memory plus USB, ADC, timers, and communication peripherals in one IC. Key differentiating features include the built-in USB 2.0 full-speed controller with 8KB of boot code support for firmware-updatable devices, a 12-channel 10-bit ADC for analog sensing, high-speed PWM outputs from 4-bit and 8/16-bit timers, and a JTAG interface for on-chip debugging. Operation spans 2.7V to 5.5V, supporting both 3.3V and 5V designs. Architecturally, the ATmega16U4 pairs the AVR RISC core with 32 general-purpose 8-bit registers directly connected to the ALU, giving high code density and throughput of up to 16 MIPS at 16 MHz. The USB controller integrates transceivers and PLL clock generation, removing the need for an external USB interface chip such as the legacy FT232 class of bridges. Typical applications include USB HID keyboards and mice, USB-powered control nodes, joystick and game controllers, and industrial sensors that stream data over USB. The ATMEGA16U4-AU is also the core of many open-source USB development boards in the Arduino ecosystem family lineage. Design consideration: at 5V/16MHz the device runs at its full-speed corner; keep VCC decoupling close to both VCC pins and route USB D+/D- as a 90-ohm differential pair for signal integrity. This page adds value beyond the datasheet by synthesizing drop-in alternatives, comparison tables, design notes, and sourcing context in one place.

견적 요청 문의하기
ATMEGA16U4-AUR - 8-Bit AVR MCU 16KB Flash USB 2.0 | Microchip
ATMEGA16U4-AUR

ATMEGA16U4-AUR - 8-Bit AVR MCU 16KB Flash USB 2.0 | Microchip

The Microchip Technology ATMEGA16U4-AUR is a low-power 8-bit AVR RISC microcontroller with 16 KB ISP FLASH memory, 2.5 KB SRAM, 1 KB EEPROM, an integrated USB 2.0 full-speed/low-speed device controller, and a 16 MHz maximum clock, housed in a 44-pin TQFP (10x10 mm) package. A microcontroller (MCU) is a single-chip computer integrating a processor core, memory, and peripherals such as timers, ADCs, and communication interfaces. The ATmega16U4 belongs to the AVR ATmega USB family within the broader hierarchy of embedded microcontrollers -> 8-bit MCUs -> AVR RISC architecture, positioned for applications that need native USB connectivity without an external USB interface chip. Key features include 16 KB of self-programmable ISP FLASH with an 8 KB boot code section, a 12-channel 10-bit ADC, high-speed PWM channels, a JTAG interface for on-chip debugging, and USB 2.0 full-speed device operation. The AVR enhanced RISC core executes most instructions in a single clock cycle, achieving throughput approaching 1 MIPS per MHz - up to 16 MIPS at 16 MHz. Technically, the device operates from 2.7 V to 5.5 V, making it compatible with both 3.3 V and 5 V logic systems. The Harvard architecture separates program and data buses for deterministic execution, while in-system programming and boot-loader support enable field firmware updates through the USB port itself. Typical applications include USB HID devices (keyboards, mice, game controllers), USB-to-serial bridges, custom mechanical keyboards, industrial sensors with USB reporting, and consumer electronics requiring direct USB enumeration. A key design consideration: the USB controller requires a stable 16 MHz crystal for full-speed operation, and the 2.5 KB SRAM limits large buffering applications - move to the pin-compatible ATMEGA32U4 for 32 KB FLASH. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기
ATMEGA16U4-MUR - 8-bit AVR USB MCU 16KB 16MHz VQFN-44 | Microchip
ATMEGA16U4-MUR

ATMEGA16U4-MUR - 8-bit AVR USB MCU 16KB 16MHz VQFN-44 | Microchip

The Microchip Technology ATMEGA16U4-MUR is a low-power 8-bit AVR RISC microcontroller with 16 KB ISP flash memory, 16 MHz max operating frequency, and an integrated USB 2.0 full-speed/low-speed device controller, housed in a 44-pin VQFN (7x7 mm) package. According to the Microchip product page, the device also provides a 8 KB boot code section, 2.5 KB SRAM, 1024 B EEPROM, high-speed PWMs, a 12-channel 10-bit ADC, and a JTAG interface for on-chip debugging. A USB microcontroller (USB MCU) is a microcontroller that integrates a USB transceiver and protocol engine on-chip, eliminating the need for an external USB interface chip. Within the power/performance hierarchy, the ATmega16U4 sits in the 8-bit AVR ATmega family, which is part of the broader microcontroller unit (MCU) class of embedded semiconductor devices. Key differentiating features include single-cycle execution of most instructions delivering up to 1 MIPS per MHz throughput, an on-chip USB 2.0 device controller with 8 KB of boot code space for field firmware updates, and in-system programmable (ISP) flash that allows firmware reprogramming on the assembled PCB. The enhanced AVR RISC core combines a rich instruction set with 32 general-purpose working registers, all directly connected to the arithmetic logic unit. Technically, the ATmega16U4/ATmega32U4 family is a low-power CMOS design based on the AVR enhanced RISC architecture, per the Atmel-7766 datasheet summary. Its 12-channel 10-bit ADC supports analog sensing, while high-speed PWM outputs suit motor control and LED dimming. The JTAG boundary-scan capability supports production test flows. Typical applications include USB keyboards, mice and game controllers, custom USB HID devices, battery-powered instruments requiring both USB connectivity and low standby power, and embedded sensor nodes using the 10-bit ADC. When designing with this device, budget the VQFN-44 (7x7 mm) land pattern carefully and note that the -MUR suffix indicates tape-and-reel industrial-temperature, green packaging. This page synthesizes distributor pricing, drop-in alternative analysis, pin compatibility notes, and practical design guidance not found in the manufacturer datasheet.

견적 요청 문의하기
ATMEGA2560-16AI - 16MHz 256KB AVR MCU | Microchip
ATMEGA2560-16AI

ATMEGA2560-16AI - 16MHz 256KB AVR MCU | Microchip

Microchip ATMEGA2560-16AI is an 8-bit AVR RISC microcontroller rated for 16 MHz operation, with 256 KB of flash memory, 8 KB of SRAM, and 4 KB of EEPROM. The device provides 86 general-purpose I/O lines and 32 general-purpose working registers, making it suitable for embedded control systems with substantial peripheral connectivity. It is supplied in a 100-lead TQFP package and operates from a 5 V supply according to the distributor listing. An 8-bit AVR microcontroller is a programmable integrated circuit designed to execute compact embedded-control firmware using the AVR reduced-instruction-set computer architecture. The ATMEGA2560 belongs to the broader microcontroller hierarchy: MCU, embedded processor, digital controller, and semiconductor. Its combination of program memory, SRAM, EEPROM, timers, serial interfaces, and GPIO makes it useful where a single device must coordinate displays, sensors, actuators, communications, and timing functions. The verified product information identifies 256 KB of ISP flash memory, 8 KB SRAM, 4 KB EEPROM, 86 general-purpose I/O lines, 32 working registers, a real-time counter, and six flexible timer/counter resources. The 16 MHz speed suffix indicates the 16 MHz operating class, while the I package designation is associated with the listed 100-pin TQFP ordering variant. The device is based on the AVR architecture and is widely recognized in Arduino Mega-class embedded platforms, although application support should be verified for a specific board and firmware environment. Typical applications include industrial automation, robotics, data acquisition, environmental monitoring, embedded instrumentation, and communication controllers. The large I/O count can simplify designs that would otherwise require multiple smaller controllers, while the 256 KB flash capacity supports larger firmware images than many entry-level AVR devices. The ATMEGA2560-16AI is therefore useful when system integration, peripheral count, and software capacity matter more than using the smallest or lowest-power MCU. Designers should confirm the exact pinout, power requirements, clock configuration, peripheral multiplexing, programming interface, and package details from the manufacturer datasheet before layout. Decoupling, oscillator routing, reset design, and unused-pin treatment should follow the relevant hardware guidance. Because the supplied data does not include a verified price table or complete electrical limit table, those values are not inferred here.

견적 요청 문의하기
ATMEGA2560-16AU - 8-bit AVR MCU 256KB Flash 16MHz | Microchip
ATMEGA2560-16AU

ATMEGA2560-16AU - 8-bit AVR MCU 256KB Flash 16MHz | Microchip

The Microchip Technology ATMEGA2560-16AU is a high-performance, low-power 8-bit AVR RISC microcontroller with 256 KB ISP Flash, 8 KB SRAM, 4 KB EEPROM, 86 general-purpose I/O lines, and a maximum clock frequency of 16 MHz, housed in a 100-pin TQFP (14x14 mm) package. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, forming the lowest tier of the embedded computing hierarchy (MCU -> embedded processor -> system-on-chip -> computing system). The ATmega2560 belongs to the AVR family of enhanced RISC microcontrollers, executing most instructions in a single clock cycle to achieve throughput approaching 1 MIPS per MHz, allowing designers to optimize power consumption versus processing speed. Key features include 256 KB of in-system programmable Flash with a separate boot sector supporting In-Application Programming, 4 KB EEPROM for non-volatile parameter storage, 8 KB internal SRAM, and 86 GPIO lines with internal pull-ups. The peripheral set comprises six flexible timer/counters with compare modes, four 8-bit PWM channels, six/two 16-bit PWM channels, an 8-channel 10-bit ADC, four USARTs, SPI, TWI (I2C), and a JTAG interface for on-chip debugging and boundary scan. The AVR core uses a Harvard architecture with 32 general-purpose working registers directly connected to the ALU, so two independent registers can be accessed in one instruction executed in one cycle. This RISC structure delivers code efficiency and deterministic execution suited to real-time control tasks, while the rich peripheral bank offloads timing-critical functions from software. Typical applications include the Arduino Mega 2560 development platform, industrial automation controllers, robotics and motor control systems, and instrumentation requiring many I/O channels and multiple serial links. Four hardware USARTs and the 86 I/O lines make it especially popular for boards that must drive shields, displays, and sensors simultaneously. When designing with the ATMEGA2560-16AU, remember it is rated for 4.5V to 5.5V operation at 16 MHz; lower-speed grades (the V variant) run at reduced voltage, so check supply rail compatibility before substituting. Provide 100 nF decoupling on each VCC pin pair and route the analog AVCC supply cleanly for best ADC accuracy. This page synthesizes distributor pricing, drop-in alternatives, pinout guidance, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기
ATMEGA2560-16AUA0 - 8-bit AVR MCU 16MHz 256KB | Microchip
ATMEGA2560-16AUA0

ATMEGA2560-16AUA0 - 8-bit AVR MCU 16MHz 256KB | Microchip

The Microchip Technology ATMEGA2560-16AUA0 is an 8-bit AVR RISC microcontroller running at 16 MHz with 256 KB ISP FLASH (128K x 16), 8 KB SRAM, and 4 KB EEPROM, housed in a 100-pin TQFP (14x14 mm) surface-mount package. An 8-bit AVR microcontroller is a single-chip computer that integrates a Harvard-architecture RISC CPU, program memory, data memory, and peripherals such as UARTs, timers, ADCs, and SPI/I2C interfaces. Within the power-management and embedded-control hierarchy, it sits as the system brain in microcontroller ICs, executing powerful instructions in a single clock cycle to deliver throughputs approaching 1 MIPS per MHz, letting designers optimize power consumption against processing speed. Key features include the 256 KB in-system self-programmable FLASH, the largest of the ATmega640/1280/2560 family, plus 86 general-purpose I/O lines and 32 general-purpose working registers. Six flexible timer/counters with compare modes and PWM, along with multiple hardware serial interfaces, reduce external component count in multi-channel control designs. Architecturally, the AVR enhanced RISC core pairs a large register file directly with the ALU, so a single instruction accesses two independent registers in one clock cycle. This eliminates the accumulator bottleneck of classic 8-bit architectures and gives the ATMEGA2560-16AUA0 deterministic, single-cycle execution suitable for real-time control loops. The 100-TQFP (14x14 mm) package exposes all 86 GPIO plus power, ground, reset, and crystal pins on a 0.5 mm pitch footprint shared across the ATmega640/1280/2560 family. Typical applications include Arduino Mega-compatible development boards, 3D printer mainboards, industrial automation controllers, robotics platforms, and multi-UART sensor hubs, where 5V-tolerant I/O, generous FLASH for complex firmware, and many timer channels are decisive. Design consideration: keep decoupling capacitors on every VCC/AVCC pin pair close to the 100-TQFP pads, and verify supply voltage versus the 16 MHz speed grade before layout, since underspecified supplies at full clock rate are a common bring-up pitfall. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기
ATMEGA2560-16AUR - 8-bit AVR MCU 256KB Flash 16MHz | Microchip (Tape & Reel)
ATMEGA2560-16AUR

ATMEGA2560-16AUR - 8-bit AVR MCU 256KB Flash 16MHz | Microchip (Tape & Reel)

The Microchip Technology ATMEGA2560-16AUR is a high-performance, low-power 8-bit AVR RISC microcontroller with 256 KB ISP Flash, 8 KB SRAM, 4 KB EEPROM, 86 general-purpose I/O lines, and a maximum clock frequency of 16 MHz, housed in a 100-pin TQFP (14x14 mm) package. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, forming the lowest tier of the embedded computing hierarchy (MCU -> embedded processor -> system-on-chip -> computing system). The ATmega2560 belongs to the AVR family of enhanced RISC microcontrollers, executing most instructions in a single clock cycle to achieve throughput approaching 1 MIPS per MHz, allowing designers to optimize power consumption versus processing speed. Key features include 256 KB of in-system programmable Flash with a separate boot sector supporting In-Application Programming, 4 KB EEPROM for non-volatile parameter storage, 8 KB internal SRAM, and 86 GPIO lines with internal pull-ups. The peripheral set comprises six flexible timer/counters with compare modes, four 8-bit PWM channels, six/two 16-bit PWM channels, an 8-channel 10-bit ADC, four USARTs, SPI, TWI (I2C), and a JTAG interface for on-chip debugging and boundary scan. The AVR core uses a Harvard architecture with 32 general-purpose working registers directly connected to the ALU, so two independent registers can be accessed in one instruction executed in one cycle. This RISC structure delivers code efficiency and deterministic execution suited to real-time control tasks, while the rich peripheral bank offloads timing-critical functions from software. Typical applications include the Arduino Mega 2560 development platform, industrial automation controllers, robotics and motor control systems, and instrumentation requiring many I/O channels and multiple serial links. Four hardware USARTs and the 86 I/O lines make it especially popular for boards that must drive shields, displays, and sensors simultaneously. When designing with the ATMEGA2560-16AUR, remember it is rated for 4.5V to 5.5V operation at 16 MHz; lower-speed grades (the V variant) run at reduced voltage, so check supply rail compatibility before substituting. Provide 100 nF decoupling on each VCC pin pair and route the analog AVCC supply cleanly for best ADC accuracy. This page synthesizes distributor pricing, drop-in alternatives, pinout guidance, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기
ATMEGA2560-16CU - 8-bit AVR MCU, 16MHz, 256KB Flash | Microchip
ATMEGA2560-16CU

ATMEGA2560-16CU - 8-bit AVR MCU, 16MHz, 256KB Flash | Microchip

The Microchip Technology ATMEGA2560-16CU is a high-performance, low-power 8-bit AVR RISC microcontroller running at 16 MHz, with 256 KB of ISP Flash memory, 8 KB SRAM, and 4 KB EEPROM, housed in a 100-ball CBGA (9x9 mm) package. According to the Microchip product page, it also provides 86 general purpose I/O lines, 32 general purpose working registers, a real-time counter, and six flexible timer/counters. An 8-bit AVR microcontroller is a Harvard-architecture RISC processor that executes most instructions in a single clock cycle, positioning it in the embedded hierarchy as: microcontroller -> 8-bit MCU -> AVR ATmega family -> semiconductor IC. This architecture delivers up to 16 MIPS throughput at 16 MHz, making it a mainstay of cost-sensitive embedded control. Key features include in-system programmable (ISP) Flash enabling firmware updates without removing the chip, 256 KB of program memory for large code bases, four 8-bit and four 16-bit timers, and multiple serial interfaces. The 86 GPIO lines make it well suited to designs that must drive many peripherals or parallel buses directly. Technical depth: the AVR core uses a two-stage pipeline with single-cycle execution for the majority of instructions. The ATMEGA2560 integrates JTAG for on-chip debugging and boundary scan, plus watchdog timer, brown-out detection, and multiple sleep modes for power optimization. The 16 MHz speed grade (-16) requires a 4.5V to 5.5V supply. Typical applications include Arduino Mega-compatible boards, robotics controllers, 3D printer mainboards, and industrial control panels where abundant I/O and mature AVR tooling matter more than raw processing speed. Design consideration: the CBGA package requires careful PCB land-pattern design and reflow profiling; verify ball-map compatibility before substituting TQFP-family variants, which share the die but not the footprint. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기
ATMEGA2560-16CUR - 8-bit AVR MCU, 16MHz, 256KB Flash | Microchip (Tape & Reel)
ATMEGA2560-16CUR

ATMEGA2560-16CUR - 8-bit AVR MCU, 16MHz, 256KB Flash | Microchip (Tape & Reel)

The Microchip Technology ATMEGA2560-16CUR is a high-performance, low-power 8-bit AVR RISC microcontroller running at 16 MHz, with 256 KB of ISP Flash memory, 8 KB SRAM, and 4 KB EEPROM, housed in a 100-ball CBGA (9x9 mm) package. According to the Microchip product page, it also provides 86 general purpose I/O lines, 32 general purpose working registers, a real-time counter, and six flexible timer/counters. An 8-bit AVR microcontroller is a Harvard-architecture RISC processor that executes most instructions in a single clock cycle, positioning it in the embedded hierarchy as: microcontroller -> 8-bit MCU -> AVR ATmega family -> semiconductor IC. This architecture delivers up to 16 MIPS throughput at 16 MHz, making it a mainstay of cost-sensitive embedded control. Key features include in-system programmable (ISP) Flash enabling firmware updates without removing the chip, 256 KB of program memory for large code bases, four 8-bit and four 16-bit timers, and multiple serial interfaces. The 86 GPIO lines make it well suited to designs that must drive many peripherals or parallel buses directly. Technical depth: the AVR core uses a two-stage pipeline with single-cycle execution for the majority of instructions. The ATMEGA2560 integrates JTAG for on-chip debugging and boundary scan, plus watchdog timer, brown-out detection, and multiple sleep modes for power optimization. The 16 MHz speed grade (-16) requires a 4.5V to 5.5V supply. Typical applications include Arduino Mega-compatible boards, robotics controllers, 3D printer mainboards, and industrial control panels where abundant I/O and mature AVR tooling matter more than raw processing speed. Design consideration: the CBGA package requires careful PCB land-pattern design and reflow profiling; verify ball-map compatibility before substituting TQFP-family variants, which share the die but not the footprint. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기
ATMEGA2560V-8AI - 8MHz 256KB AVR MCU | Microchip
ATMEGA2560V-8AI

ATMEGA2560V-8AI - 8MHz 256KB AVR MCU | Microchip

The Microchip Technology ATMEGA2560V-8AI is an 8-bit AVR RISC-based microcontroller with an 8 MHz maximum operating frequency, 256 KB of in-system programmable Flash memory, 8 KB SRAM, and 4 KB EEPROM in a 100-pin TQFP package. It provides 86 general-purpose I/O lines and integrated connectivity including EBI/EMI, I2C, SPI, and four USART modules. The -8AI suffix identifies an 8 MHz grade with an industrial temperature classification, while the V designation identifies the voltage and feature variant within the ATmega family. What is an AVR microcontroller? An AVR is an 8-bit RISC microcontroller architecture designed by Microchip for embedded control, communications, and real-time peripheral management. In the system hierarchy, ATMEGA2560V-8AI is a microcontroller within the integrated-circuit and embedded-processing categories. Its program memory, SRAM, EEPROM, I/O ports, timers, serial interfaces, and interrupt system allow a single device to combine control logic with multiple communication channels. Key features include 256 KB of Flash organized as 128K x 16, 8 KB of internal SRAM, 4 KB of EEPROM, and 86 general-purpose I/O lines. The device also includes four USARTs, an SPI interface, a byte-oriented two-wire serial interface, an external memory interface, and flexible timer/counter resources. These features support applications requiring multiple serial links, periodic timing, analog-to-digital conversion, and firmware storage. The ATmega core provides 32 general-purpose working registers connected directly to the arithmetic logic unit. This architecture supports efficient register-based instruction execution and is well suited to compact embedded control loops. The manufacturer datasheet identifies the ATmega2560 family as a high-performance, low-power AVR RISC-based device with real-time counters and flexible timer/counter blocks. Typical applications include industrial automation controllers, data acquisition systems, communications gateways, motor-control and sequencing equipment, embedded test instruments, and custom Arduino-compatible or similar embedded platforms. The four USARTs are especially useful when the design must connect several independent serial devices. Designers should verify the exact pin functions, power rails, clock requirements, programming interface, and timing constraints against the manufacturer datasheet before layout. The 100-pin TQFP footprint requires careful fanout and exposed-pad or thermal considerations where applicable. Firmware replacement should also be validated because different ATmega variants can differ in peripheral availability, fuse behavior, and package details. This page combines verified manufacturer and distributor information with package, interface, application, comparison, and design guidance to support rapid component selection and sourcing.

견적 요청 문의하기
ATMEGA2560V-8AU - 256KB Flash, 1.8-5.5V AVR MCU 8MHz | Microchip
ATMEGA2560V-8AU

ATMEGA2560V-8AU - 256KB Flash, 1.8-5.5V AVR MCU 8MHz | Microchip

The Microchip Technology (formerly Atmel) ATMEGA2560V-8AU is a high-performance, low-power 8-bit AVR RISC microcontroller integrating 256 KB in-system-programmable Flash, 8 KB SRAM, 4 KB EEPROM, and 86 general-purpose I/O lines in a 100-pin TQFP surface-mount package rated for -40C to +85C operation from a 1.8 V to 5.5 V supply at up to 8 MHz. A microcontroller (MCU) is a single-chip computer that combines a CPU core, program and data memory, and I/O peripherals such as timers, serial interfaces and interrupt logic on one die. Within the embedded-computing hierarchy the ATmega2560 family sits in the mainstream 8-bit flash MCU class, sitting above smaller ATmega parts such as the ATmega328P and below 32-bit ARM Cortex-M devices when applications demand very large GPIO and peripheral counts rather than raw compute throughput. Key features include the advanced AVR RISC architecture executing 131 powerful instructions, mostly in a single clock cycle, with 32 general-purpose working registers and fully static operation for up to 16 MIPS throughput at 16 MHz (8 MHz maximum for the V low-voltage grade). The device integrates six flexible timer/counters with compare modes and PWM, four USARTs, a byte-oriented 2-wire serial interface (TWI/I2C), an SPI serial interface, a real-time counter with separate oscillator, a watchdog timer and a 16-channel 10-bit ADC. In-system programming (ISP) and self-programming support enable field firmware updates without removing the chip. The V suffix denotes the extended 1.8 V to 5.5 V operating range, allowing direct operation from two alkaline cells or a single lithium cell with a boost converter, which makes the ATMEGA2560V-8AU attractive for battery-powered instruments. The Harvard-architecture dual-memory bus keeps program fetch and data access independent, sustaining efficient C-compiled code density, and the on-chip RC oscillator plus XTAL1/XTAL2 crystal inputs reduce external component count while supporting accurate USART baud rates. Typical applications include industrial automation controllers with large I/O counts, 3D-printer mainboards (the Arduino Mega 2560 platform), robotics controllers, and multi-port data loggers that must exploit four USART channels plus a wide supply range. When designing with this part, consult the maximum clock rate versus VCC curve because at 1.8 V the maximum guaranteed clock drops well below 8 MHz. This page synthesizes distributor pricing, drop-in same-family alternatives, a full 100-pin TQFP pinout, and practical design notes not consolidated in the manufacturer datasheet. Pricing is referenced as of 2026-09-17.

견적 요청 문의하기
ATMEGA2560V-8AUR - 256KB Flash, 1.8-5.5V AVR MCU 8MHz | Microchip (Tape & Reel)
ATMEGA2560V-8AUR

ATMEGA2560V-8AUR - 256KB Flash, 1.8-5.5V AVR MCU 8MHz | Microchip (Tape & Reel)

The Microchip Technology (formerly Atmel) ATMEGA2560V-8AUR is a high-performance, low-power 8-bit AVR RISC microcontroller integrating 256 KB in-system-programmable Flash, 8 KB SRAM, 4 KB EEPROM, and 86 general-purpose I/O lines in a 100-pin TQFP surface-mount package rated for -40C to +85C operation from a 1.8 V to 5.5 V supply at up to 8 MHz. A microcontroller (MCU) is a single-chip computer that combines a CPU core, program and data memory, and I/O peripherals such as timers, serial interfaces and interrupt logic on one die. Within the embedded-computing hierarchy the ATmega2560 family sits in the mainstream 8-bit flash MCU class, sitting above smaller ATmega parts such as the ATmega328P and below 32-bit ARM Cortex-M devices when applications demand very large GPIO and peripheral counts rather than raw compute throughput. Key features include the advanced AVR RISC architecture executing 131 powerful instructions, mostly in a single clock cycle, with 32 general-purpose working registers and fully static operation for up to 16 MIPS throughput at 16 MHz (8 MHz maximum for the V low-voltage grade). The device integrates six flexible timer/counters with compare modes and PWM, four USARTs, a byte-oriented 2-wire serial interface (TWI/I2C), an SPI serial interface, a real-time counter with separate oscillator, a watchdog timer and a 16-channel 10-bit ADC. In-system programming (ISP) and self-programming support enable field firmware updates without removing the chip. The V suffix denotes the extended 1.8 V to 5.5 V operating range, allowing direct operation from two alkaline cells or a single lithium cell with a boost converter, which makes the ATMEGA2560V-8AUR attractive for battery-powered instruments. The Harvard-architecture dual-memory bus keeps program fetch and data access independent, sustaining efficient C-compiled code density, and the on-chip RC oscillator plus XTAL1/XTAL2 crystal inputs reduce external component count while supporting accurate USART baud rates. Typical applications include industrial automation controllers with large I/O counts, 3D-printer mainboards (the Arduino Mega 2560 platform), robotics controllers, and multi-port data loggers that must exploit four USART channels plus a wide supply range. When designing with this part, consult the maximum clock rate versus VCC curve because at 1.8 V the maximum guaranteed clock drops well below 8 MHz. This page synthesizes distributor pricing, drop-in same-family alternatives, a full 100-pin TQFP pinout, and practical design notes not consolidated in the manufacturer datasheet. Pricing is referenced as of 2026-09-17.

견적 요청 문의하기
ATMEGA2560V-8CU - 8-Bit AVR MCU 256KB 8MHz CBGA-100 | Microchip (Tape & Reel)
ATMEGA2560V-8CU

ATMEGA2560V-8CU - 8-Bit AVR MCU 256KB 8MHz CBGA-100 | Microchip (Tape & Reel)

The Microchip Technology ATMEGA2560V-8CU is an 8-bit AVR RISC microcontroller with 256KB (128K x 16) ISP Flash memory, 8KB SRAM, and 4KB EEPROM, executing at up to 8MHz across the 1.8V to 5.5V voltage range, housed in a 100-ball CBGA (9x9 mm) package. A microcontroller is a single-chip computer that integrates a processor core, program memory, data memory, and peripherals on one die, sitting at the lowest tier of the embedded-computing hierarchy (MCU -> SoC -> application processor). The AVR ATmega family uses an advanced RISC architecture with 131 mostly single-cycle instructions and 32 general-purpose working registers, delivering fully static operation rated up to 16 MIPS throughput at 16MHz. Key features include 256KB of self-programmable Flash, four 16-bit and two 8-bit timers, four programmable serial USARTs, master/slave SPI, a byte-oriented 2-wire (I2C-compatible) interface, an 8/16-channel 10-bit ADC, an output-compare modulator, programmable watchdog timer with separate on-chip oscillator, on-chip analog comparator, brown-out detection, power-on reset, PWM outputs, and interrupt and wake-up on pin change. The V-8 speed/voltage grade supports the full 1.8V operating corner, making the device well suited to battery-powered designs, while the 100-ball CBGA provides a compact 9x9 mm footprint for space-constrained boards. The industrial temperature rating and GREEN/RoHS material set support professional-grade deployments. Typical applications include battery-powered data loggers, industrial automation controllers, multi-channel sensor acquisition nodes, and robotics control boards where multiple UARTs and abundant GPIO (86 general-purpose I/O lines) are required. Design consideration: at low supply voltages the maximum safe clock frequency derates; below 2.7V the device is limited to 8MHz operation, so clock selection and brown-out detector thresholds must be chosen together. This page synthesizes distributor pricing, drop-in alternatives, comparison tables, and practical design notes not found in the manufacturer datasheet, providing information gain for procurement and engineering evaluation.

견적 요청 문의하기
ATMEGA2560V-8CUR - 8-Bit AVR MCU 256KB 8MHz CBGA-100 | Microchip
ATMEGA2560V-8CUR

ATMEGA2560V-8CUR - 8-Bit AVR MCU 256KB 8MHz CBGA-100 | Microchip

The Microchip Technology ATMEGA2560V-8CUR is an 8-bit AVR RISC microcontroller with 256KB (128K x 16) ISP Flash memory, 8KB SRAM, and 4KB EEPROM, executing at up to 8MHz across the 1.8V to 5.5V voltage range, housed in a 100-ball CBGA (9x9 mm) package. A microcontroller is a single-chip computer that integrates a processor core, program memory, data memory, and peripherals on one die, sitting at the lowest tier of the embedded-computing hierarchy (MCU -> SoC -> application processor). The AVR ATmega family uses an advanced RISC architecture with 131 mostly single-cycle instructions and 32 general-purpose working registers, delivering fully static operation rated up to 16 MIPS throughput at 16MHz. Key features include 256KB of self-programmable Flash, four 16-bit and two 8-bit timers, four programmable serial USARTs, master/slave SPI, a byte-oriented 2-wire (I2C-compatible) interface, an 8/16-channel 10-bit ADC, an output-compare modulator, programmable watchdog timer with separate on-chip oscillator, on-chip analog comparator, brown-out detection, power-on reset, PWM outputs, and interrupt and wake-up on pin change. The V-8 speed/voltage grade supports the full 1.8V operating corner, making the device well suited to battery-powered designs, while the 100-ball CBGA provides a compact 9x9 mm footprint for space-constrained boards. The industrial temperature rating and GREEN/RoHS material set support professional-grade deployments. Typical applications include battery-powered data loggers, industrial automation controllers, multi-channel sensor acquisition nodes, and robotics control boards where multiple UARTs and abundant GPIO (86 general-purpose I/O lines) are required. Design consideration: at low supply voltages the maximum safe clock frequency derates; below 2.7V the device is limited to 8MHz operation, so clock selection and brown-out detector thresholds must be chosen together. This page synthesizes distributor pricing, drop-in alternatives, comparison tables, and practical design notes not found in the manufacturer datasheet, providing information gain for procurement and engineering evaluation.

견적 요청 문의하기
ATMEGA2561-16AU - 8-Bit AVR MCU 16MHz 256KB Flash | Microchip
ATMEGA2561-16AU

ATMEGA2561-16AU - 8-Bit AVR MCU 16MHz 256KB Flash | Microchip

The Microchip Technology ATMEGA2561-16AU is a high-performance, low-power 8-bit AVR RISC microcontroller with 256 KB ISP flash memory, 8 KB SRAM, 4 KB EEPROM, 86 general-purpose I/O lines, and a 16 MHz maximum clock, housed in a 64-pin TQFP (14x14 mm) surface-mount package. An 8-bit AVR microcontroller is a complete computer-on-a-chip built around the AVR enhanced RISC architecture, combining CPU, program flash, data SRAM, EEPROM, timers, serial interfaces, and an ADC within a single integrated circuit. In the power management hierarchy of embedded systems, the MCU sits at the center of the control chain, orchestrating sensors, actuators, and communication links. The AVR family is widely used because of its single-cycle instruction execution and rich peripheral set. Key features of the ATMEGA2561-16AU include 131 powerful instructions with most executing in a single clock cycle, delivering up to 16 MIPS throughput at 16 MHz. It provides four USARTs for multi-channel serial communication, a byte-oriented 2-wire serial interface (TWI/I2C), an SPI interface, six flexible timer/counters with compare modes and PWM, a real-time counter, and an 8-channel 10-bit ADC. The 256 KB self-programmable flash enables bootloader-based field firmware updates in large applications. Architecturally, the device uses the AVR advanced RISC core with 32 general-purpose working registers directly connected to the ALU, allowing one-cycle access that avoids the accumulator bottleneck of classical 8-bit architectures. Fully static operation supports clock speeds down to DC for ultra-low-power designs. JTAG boundary-scan and on-chip debug support simplify production testing and firmware development. Typical applications include industrial automation controllers, building management and HVAC control panels, test and measurement instrumentation, and motor control systems. The four USARTs and 86 I/O lines make it well suited to equipment that must talk to several serial peripherals while driving displays, keypads, and relays. When designing with this part, remember the 16 suffix denotes a 4.5V to 5.5V operating range; the V-suffix variant (ATMEGA2561V-8AU) is required for 2.7V to 5.5V battery designs, and its maximum clock is 8 MHz. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet, with pricing referenced as of 2026-10-07.

견적 요청 문의하기
ATMEGA2561-16AUR - 8-bit AVR MCU 256KB 16MHz | Microchip
ATMEGA2561-16AUR

ATMEGA2561-16AUR - 8-bit AVR MCU 256KB 16MHz | Microchip

The Microchip Technology ATMEGA2561-16AUR is a high-performance, low-power 8-bit AVR RISC microcontroller with 256 KB ISP Flash memory, 8 KB SRAM, 4 KB EEPROM, and 54 general-purpose I/O lines, executing up to 16 MIPS at 16 MHz in a 64-pin TQFP (14x14 mm) package. According to the Microchip product page, it belongs to the AVR ATmega family with 32 general-purpose working registers and a real-time counter. A microcontroller unit (MCU) is a single integrated circuit that combines a processor core, program memory (Flash), data memory (SRAM and EEPROM), and peripheral interfaces such as UART, SPI, and I2C. Within the semiconductor hierarchy, the ATmega2561 sits in the 8-bit microcontroller category under embedded processors, a superset that includes MCUs, MPUs, and DSPs. 8-bit AVRs remain widely used where deterministic execution, simple toolchains, and 5V tolerance matter. Key features include the AVR enhanced RISC architecture with mostly single-cycle instruction execution, six flexible timer/counters with compare modes and PWM, four USARTs for serial communication, a byte-oriented 2-wire serial interface (TWI/I2C), a master/slave SPI interface, an 8-channel 10-bit ADC, a programmable watchdog timer with separate on-chip oscillator, an on-chip analog comparator, and interrupt and wake-up on pin change for low-power designs. The ATmega2561 is the 64-pin member of the ATmega640/1280/1281/2560/2561 family, sharing peripherals with the 100-pin ATmega2560 in a more compact footprint. The 16 MHz -16 speed grade delivers up to 16 MIPS throughput, while the AVR Harvard architecture with 32 registers gives exceptionally efficient compiled C code. The 256 KB Flash supports self-programming via ISP bootloader, and the 4 KB EEPROM retains calibration data through power cycles. Operating voltage is 4.5V to 5.5V with industrial temperature range of -40C to +85C for the 'I' suffix. Typical applications include industrial automation controllers, motor control panels, building automation, embedded instrumentation, and legacy 5V board designs requiring pin-compatible upgrades from ATmega128 designs. For reliable design, use the internal PLL-free clocking path, keep XTAL1/XTAL2 traces short, and budget the watchdog oscillator tolerance when relying on WDT reset timing. This page synthesizes distributor pricing, drop-in alternatives, comparison tables, and practical design notes not found in the manufacturer datasheet.

견적 요청 문의하기
ATMEGA2561-16MU - 8-bit AVR MCU 256KB Flash 16MHz 64-QFN | Microchip
ATMEGA2561-16MU

ATMEGA2561-16MU - 8-bit AVR MCU 256KB Flash 16MHz 64-QFN | Microchip

The Microchip ATMEGA2561-16MU is a high-performance, low-power 8-bit AVR RISC-based microcontroller integrating 256 KB of in-system programmable Flash, 8 KB SRAM, and 4 KB EEPROM, operating at up to 16 MHz with 16 MIPS throughput, packaged in a 64-lead VFQFN (9x9 mm) with exposed thermal pad. The device offers 54 programmable I/O lines, 32 general-purpose working registers, and a rich peripheral set including four USARTs, one TWI (I2C) port, one SPI port, two 8-bit timer/counters and four 16-bit timer/counters with compare/PWM modes, an 8-channel 10-bit ADC, a JTAG debug interface, and a programmable watchdog timer with separate on-chip oscillator. An AVR microcontroller (sometimes called an Advanced Virtual RISC microcontroller) is a single-chip computer built around the Atmel AVR 8-bit RISC core, executing most instructions in a single clock cycle to deliver deterministic throughput. ATmega2561 belongs to the megaAVR family, sitting between tinyAVR and XMEGA in Microchip's 8-bit hierarchy, and is commonly used where higher pin count and larger memory are needed without moving to 32-bit ARM Cortex-M parts. Key features of the ATMEGA2561-16MU include 256 KB self-programmable Flash with Read-While-Write support, 8 KB on-chip SRAM, 4 KB true EEPROM with 100,000 erase/write cycles endurance, an internal calibrated RC oscillator, and six software-selectable power-saving modes that can reduce active current to microampere levels for battery-operated designs. The 8-channel 10-bit successive-approximation ADC delivers up to 15 kSPS at full resolution, and the on-chip analog comparator supports single-ended and differential inputs with selectable hysteresis. Architecturally, the ATMEGA2561 uses a Harvard-style memory layout with separate program Flash and data SRAM buses, a hardware multiplier supporting signed/unsigned multiply and fractional multiply instructions, and a deterministic interrupt controller with up to 57 interrupt vectors. The peripheral interconnect allows timer/counter outputs to drive ADC triggers and PWM channels, enabling motor control and power-conversion topologies without software overhead. Typical applications include industrial automation controllers, building automation gateways, smart energy metering, USB-to-UART bridges using external PHY, multi-channel data acquisition front-ends, robotic controller boards, automotive body and infotainment subsystems (when properly qualified), and hobbyist/education platforms such as Arduino-Mega-compatible designs. The wide memory and I/O count also make it a frequent fit for SCADA remote terminal units (RTUs). When designing with this device, ensure decoupling follows Microchip's recommended 100 nF ceramic on each VCC pin plus a 10 uF bulk, and respect the 5.5 V absolute-maximum VCC rating even though the part is 5 V tolerant. JTAG and ISP programming both require the RESET pin to remain in a defined state; for noise immunity, place a 10 kohm pull-up on RESET and a low-value decoupling capacitor on AVCC to maximize ADC linearity. This page synthesizes distributor inventory, 64-QFN drop-in alternatives, and practical AVR design notes not found in the manufacturer datasheet alone, accelerating part selection and PCB re-use.

견적 요청 문의하기