마이크로컨트롤러

제품 (20,000+)

MC-10105F1-821-FNA-M1-A - TPS-1 PROFINET IO SoC 100MHz | Renesas
MC-10105F1-821-FNA-M1-A

MC-10105F1-821-FNA-M1-A - TPS-1 PROFINET IO SoC 100MHz | Renesas

The Renesas Electronics MC-10105F1-821-FNA-M1-A is a TPS-1 family application-specific microcontroller / single-chip interface solution for PROFINET IO devices, integrating an ARM core with a dual-port Ethernet switch and supporting 100 Mbps full-duplex PROFINET communication. The device is housed in a 196-pin FPBGA package measuring 15 x 15 mm with 1.0 mm pitch, and is qualified for industrial operating conditions. A PROFINET IO device chip is an application-specific integrated circuit that bundles the industrial-Ethernet protocol stack, real-time (RT/IRT) media access, and a managed dual-port switch into a single silicon die so that field devices such as remote I/O blocks, variable-frequency drives, encoders, and identification readers can be designed without an external companion controller. Within the broader embedded-system hierarchy, this part sits at the junction of an industrial microcontroller (MCU), an Ethernet MAC/PHY block, and a deterministic-protocol accelerator, allowing OEMs to certify PROFINET conformance class C without writing low-level stack code from scratch. Key differentiating features include 196-BGA integration (no companion Ethernet controller needed), compliance with PROFINET specification V2.3 for real-time and isochronous real-time (IRT) classes, a 100 MHz ARM core, and Phoenix-Contact co-development with Renesas for guaranteed protocol interoperability. The dual-port integrated switch removes the need for an external PHY/MAC pair on simple star or line topologies common in field-cabinet wiring. Architecturally, the part pairs a 32-bit ARM Cortex-M-class CPU (100 MHz) with on-chip RAM, deterministic Ethernet media-access hardware, and a PROFINET IO device firmware load supplied by Renesas. This division of labor lets the host application processor focus on device-specific I/O while the TPS-1 handles cut-through switching, RT/IRT scheduling, and PROFINET alarm generation with deterministic cycle jitter below 1 µs per the device specification. Typical applications include PROFINET-IO remote I/O blocks, frequency-inverter / variable-frequency drive fieldbus interfaces, encoder and absolute-position sensor gateways, RFID-reader PROFINET nodes, and modular I/O stations in factory automation. The 100 Mbps full-duplex bandwidth comfortably exceeds typical PROFINET RT cycle times of 1 ms. When designing in the MC-10105F1-821-FNA-M1-A, plan for a 1.0 mm pitch BGA land pattern with controlled-impedance differential pairs for the MII/RGMII Ethernet traces and a 25 MHz reference crystal. Thermal management is straightforward at industrial ambient temperatures because the part is fabricated in a low-power CMOS process optimized for fan-less DIN-rail mounting. This page synthesizes distributor pricing, protocol-compliance scope, and application notes not consolidated on the manufacturer product page, helping industrial-automation design engineers evaluate the MC-10105F1-821-FNA-M1-A for PROFINET IO device integration as of 2026-10-09.

견적 요청 문의하기
MC11E1CPBE2 - 8-Bit ROMless 2 MHz MCU | NXP | 52-LQFP
MC11E1CPBE2

MC11E1CPBE2 - 8-Bit ROMless 2 MHz MCU | NXP | 52-LQFP

The NXP Semiconductors MC11E1CPBE2 is an 8-bit ROMless HC11 microcontroller operating at up to 2 MHz, with 512 bytes of RAM, 38 I/O pins, and a 52-LQFP package measuring 10 x 10 mm. It is designed for embedded control systems requiring a compact processor, digital I/O, and automotive-oriented industrial-temperature capability. A microcontroller is a semiconductor device that integrates a CPU core, memory, input/output ports, timers, and communication interfaces on one integrated circuit. In the broader hierarchy, this MC11E1CPBE2 is an 8-bit microcontroller, part of the HC11 family, and belongs to the embedded-microcontroller and semiconductor categories. Its ROMless architecture allows the application firmware to be supplied by external memory or a programming system, supporting applications where program-memory requirements vary or field programming is required. Verified distributor data identifies the MC11E1CPBE2 as an HC11 microcontroller with a 2 MHz speed grade, ROMless configuration, 512 x 8 RAM, 38 I/O, internal oscillator, and a 52-LQFP package. The 52-terminal gull-wing package is surface-mountable and uses a 10 x 10 mm outline. Because it is ROMless, designers must verify the external memory interface and programming architecture against the original system requirements before replacing or upgrading an existing design. Typical applications include automotive electronic control units, motor and actuator controllers, sensor interfaces, industrial automation equipment, and legacy embedded systems that depend on the M68HC11 CPU architecture. The 38-I/O count provides useful connectivity for digital sensors, switches, relays, communication transceivers, and control signals. The 2 MHz CPU speed is suitable for control-loop and supervisory tasks rather than high-bandwidth signal processing or modern high-performance applications. The primary design consideration is legacy software compatibility. Firmware timing, interrupt priorities, memory-mapped peripherals, external bus behavior, and package-level routing must be preserved during any replacement. Engineers should obtain the manufacturer datasheet and verify the exact pinout, electrical limits, oscillator connections, reset requirements, and programming procedure before committing to a new PCB design. This product data summarizes verified distributor specifications, package information, sourcing references, and design considerations. It does not invent electrical limits, memory-map details, or a cross-brand substitute when the supplied web results do not establish one.

견적 요청 문의하기
MC56F8002VWL - 16-bit 56800E DSC, 32MHz, 12KB Flash 28-SOIC | NXP
MC56F8002VWL

MC56F8002VWL - 16-bit 56800E DSC, 32MHz, 12KB Flash 28-SOIC | NXP

The NXP MC56F8002VWL is a 16-bit Digital Signal Controller (DSC) from the MC56F800x family, built on the 56800E core architecture. It delivers 32 MHz of CPU clock speed (per DigiKey/NXP listing) and integrates 12 KB (6K x 16) of on-chip Flash program memory alongside a 28-pin SOIC package with 23 general-purpose I/O pins. The part operates from a 1.8 V to 3.6 V supply range, making it well suited to low-voltage embedded designs. A Digital Signal Controller (DSC) is a hybrid class of programmable device that combines the deterministic interrupt response and peripheral integration of a microcontroller with the Multiply-Accumulate (MAC) engine and Harvard bus structure of a Digital Signal Processor (DSP). The 56800E core executes instructions in a single cycle where possible and is positioned in the taxonomy as: DSC -> DSP/MCU hybrid -> microcontroller -> integrated circuit -> semiconductor. DSCs target real-time control loops where the math throughput of a DSP is needed but the application footprint, cost, and tool chain of an MCU are preferred. Key features of the MC56F8002VWL include the 56800E 16-bit core, 12 KB Flash program memory, 32 MHz maximum core frequency, 23 GPIO lines, and a supply range of 1.8 V to 3.6 V. The integrated peripheral set reduces external component count in motor, lighting, and power-conversion designs. According to the NXP MC56F8006/MC56F8002 reference manual, the family integrates peripherals such as timers, PWM modules, ADCs, and communication interfaces configured per the variant. Architecturally, the 56800E core uses a dual Harvard memory structure with separate program and data buses, allowing simultaneous fetches that improve sustained throughput on control algorithms. The 12 KB Flash is sufficient for closed-loop field-oriented motor control (FOC), digital lighting ballast loops, and small power-factor correction (PFC) firmware where deterministic performance is more important than raw memory size. Typical applications for the MC56F8002VWL include low-cost BLDC/PMSM motor drives, switch-mode power supplies (SMPS), digital LED lighting ballasts, appliance control boards, and small industrial control modules. The wide 1.8 V to 3.6 V supply and integrated analog peripherals make it attractive for power-conversion applications where a single IC handles both sensing and control. When designing with this part, ensure your firmware budget fits within 12 KB Flash plus available RAM, and check the variant's peripheral mix against your PWM, ADC, and communication requirements. NXP's CodeWarrior and the newer MCUXpresso DSC toolchains support this family, and engineers should plan for the variant-specific header files to avoid peripheral register mismatches. This page synthesizes distributor pricing, lifecycle signals, drop-in 56800E family alternatives, and practical design notes not found in the manufacturer datasheet alone. The NXP product page flags End-of-Life for MC56F8002VWL, so designers should review replacement and obsolescence options before committing the part to long-life programs.

견적 요청 문의하기
MC56F8006MLC - 16-bit DSC, 56800E Core, 16KB Flash | NXP
MC56F8006MLC

MC56F8006MLC - 16-bit DSC, 56800E Core, 16KB Flash | NXP

The NXP MC56F8006MLC is a 16-bit digital signal controller (DSC) from the MC56F800x family, featuring a 56800E core operating at 64 MHz bus clock with 32 MHz core MIPS throughput, 16 KB of on-chip Flash memory, and a 32-pin LQFP package. The device integrates DSP-class signal-processing capability with microcontroller peripheral integration on a single die, targeting cost-sensitive real-time control applications. A Digital Signal Controller (DSC) is a hybrid device class that combines a microcontroller's deterministic peripheral handling with a digital signal processor's mathematical pipeline. The 56800E core belongs to the family: 56800E core -> DSC -> microcontroller -> embedded processor -> semiconductor. Compared with a traditional 8/16-bit MCU, a DSC adds hardware multiply-accumulate, single-cycle MAC, and Harvard-style bus architecture, allowing closed-loop control loops, power-conversion math, and sensor fusion to run on a single chip without an external DSP partner. The MC56F8006 sits at the entry level of NXP's DSC portfolio, designed for mathematically intensive yet price-sensitive applications. Key specifications include 16 KB Flash program memory, 1.8 V to 3.6 V single-supply operation, 23 general-purpose I/O (GPIO) pins, on-chip 12-bit ADC, PWM modules suitable for motor and power control, and serial interfaces including SCI, SPI, and I2C. The device includes an internal relaxed oscillator with PLL-based frequency multiplication to derive the 64 MHz system clock from lower-cost external references. The MC56F8006 uses a Harvard-style 56800E architecture with separate program and data buses, allowing simultaneous fetch and operand access. The integrated peripheral set includes timers, PWM, ADC, and communication blocks, eliminating external components and reducing BOM cost. Built-in boundary scan and JTAG support simplify factory test and in-field firmware updates. Typical applications include BLDC and PMSM motor control in appliance fans and pumps, digital power conversion (PFC, LLC, buck/boost), LED lighting ballasts with analog dimming, and low-end industrial sensor conditioning. The wide 1.8 V to 3.6 V supply range supports both 2.5 V and 3.3 V system rails, simplifying multi-rail designs. When designing, ensure JTAG pins are accessible for factory programming and that the internal relaxed oscillator accuracy is acceptable for the target application. For motor control, leverage the integrated PWM and ADC synchronization rather than external triggering to reduce latency and BOM cost. This page synthesizes distributor pricing, NXP product-page lifecycle notes, parametric comparison with related 56F8xxx devices, and design notes covering JTAG access, oscillator selection, and motor-control timing - content not collated in the bare manufacturer datasheet.

견적 요청 문의하기
MC56F8006VLC - 16KB Flash 32MHz DSC | NXP 32-LQFP
MC56F8006VLC

MC56F8006VLC - 16KB Flash 32MHz DSC | NXP 32-LQFP

The NXP MC56F8006VLC is a 16-bit digital signal controller (DSC) from the 56800E core-based 56F800x family, integrating 16KB of Flash program memory, 32MHz maximum CPU clock, and a flexible peripheral set in a 32-pin LQFP package. It combines DSP-class signal processing throughput with microcontroller peripherals, targeting mathematically intensive real-time control applications such as digital power conversion, motor control, and sensor signal conditioning. What is a Digital Signal Controller? A DSC is a hybrid device that merges the deterministic math engine of a digital signal processor with the integrated peripherals and ease-of-use of a microcontroller. Architecturally, a DSC sits above a plain MCU in the embedded hierarchy (microcontroller -> digital signal controller -> DSP) and below a stand-alone DSP, occupying a sweet spot where signal-processing throughput must coexist with PWM, ADC, timers, and GPIO. The 56800E core uses a unified data/program memory map and a modified Harvard bus, with single-cycle MAC support that is essential for power-loop and field-oriented motor-control algorithms. Key features of the MC56F8006VLC include 16KB Flash (organized as 8K x 16), 2KB RAM, an internal Phase-Locked Loop for clock multiplication, multiple 16-bit timers, a 12-bit ADC, PWM modules suited for switch-mode power supplies, and serial peripherals (SCI, SPI, I2C). The device operates from 1.8V to 3.6V, supports industrial temperature range (-40C to +105C or -40C to +125C per device marking), and provides 23 general-purpose I/O pins. The LQFP-32 footprint offers 0.8mm pitch and an exposed-pad option on the family for improved thermal dissipation. Typical applications include digital DC/DC and AC/DC power converters, small BLDC and PMSM motor drives (fans, pumps, appliances), uninterruptible power supplies, induction cooking, smart sensors, and LED drivers with closed-loop current regulation. The combination of DSP math throughput, low BOM cost, and a familiar MCU development flow makes it a strong choice for cost-sensitive embedded control where 8-bit MCUs run out of headroom. When designing with this part, ensure the JTAG/OnCE debug interface is accessible on the board, allocate proper decoupling on AVDD/DVDD pins, and follow NXP's PCB layout guidance for the analog sections to keep ADC performance within spec. Note that NXP has issued End-of-Life notices for several 56F800x variants; engineers should verify lifecycle status before committing to new designs.

견적 요청 문의하기
MC56F8006VLF - 16-Bit 32MHz DSC, 16KB Flash | NXP
MC56F8006VLF

MC56F8006VLF - 16-Bit 32MHz DSC, 16KB Flash | NXP

NXP Semiconductors MC56F8006VLF is a 16-bit digital signal controller with a 32 MHz 56800E core, 16 KB of flash memory, and a 48-LQFP 7 x 7 mm package. It combines digital signal processing with microcontroller peripherals for mathematically intensive, power-sensitive, real-time control applications. A digital signal controller, or DSC, is a processor category positioned between a conventional microcontroller and a digital signal processor. MC56F8006VLF executes real-time control algorithms while providing general-purpose peripherals and embedded flash in one integrated device. Its 56800E architecture is intended for motor-control, power-conversion, and industrial automation functions where deterministic control and compact embedded integration matter. The verified manufacturer material identifies a 16-bit processing core, 32 MHz operating frequency, and 16 KB flash memory. NXP describes the entry-level MC56F8006 and MCF56F8002 devices as cost-effective solutions for power-sensitive, real-time control applications. The family integrates peripherals to reduce external component count while preserving the responsiveness required by feedback-control systems. MC56F8006VLF is supplied in a 48-LQFP package, making it suitable for conventional surface-mount PCB assembly. Its 16 KB flash capacity is sufficient for compact control firmware, configuration data, and application-specific code. The 32 MHz clock and 16-bit architecture support fast mathematical processing, while the integrated peripheral set helps simplify designs that would otherwise require separate interface and control components. Typical applications include digital motor control, power-supply regulation, industrial inverter control, signal conditioning, and embedded instrumentation. The part is particularly relevant when a system needs deterministic digital filtering or feedback calculations but does not require a high-end digital signal processor. NXP’s product family positioning emphasizes mathematically intensive, power-sensitive control rather than general-purpose processing. For a new design, verify supply voltage, peripheral assignments, timing, pin multiplexing, programming requirements, and package-level constraints against the manufacturer datasheet before committing the PCB. Because MC56F8006VLF is identified as end-of-life by the NXP product page, engineers should also confirm availability, lifecycle status, and approved sourcing options before starting a production release. This page combines verified manufacturer identity, distributor specifications, lifecycle context, package information, and practical sourcing considerations. It is intended to help engineers locate the datasheet, assess the device’s real-time control role, and determine whether a legacy design requires migration planning.

견적 요청 문의하기
MC56F8006VWLR - 16KB Flash 32MHz 56800E DSC | NXP
MC56F8006VWLR

MC56F8006VWLR - 16KB Flash 32MHz 56800E DSC | NXP

The NXP MC56F8006VWLR is a 16-bit 56800E-core Digital Signal Controller (DSC) that integrates the processing power of a DSP with the peripheral integration of a microcontroller, packaged in a 28-pin wide-body SOIC (SOIC-28-300mil). Per the manufacturer datasheet, it delivers up to 32 MIPS at 32 MHz core clock, with 16 KB of program Flash (organized as 8K x 16) and operates from a 1.8 V to 3.6 V supply. A Digital Signal Controller (DSC) is a hybrid device that occupies the architectural middle ground between a pure microcontroller (MCU) and a digital signal processor (DSP). It uses a modified Harvard architecture with a deterministic interrupt model, on-chip memory, and DSP-class multiply-accumulate instructions that allow closed-loop control loops to execute in a single instruction cycle. DSCs are widely used in digitally controlled switching power supplies, motor drives, sensor signal conditioning, and LED lighting where tight math latency matters more than raw GHz throughput. Key features of the MC56F8006 include 16 KB Flash / 2 KB RAM, a 6-channel PWM module suitable for three-phase or multi-channel DC/DC control, a 12-bit ADC, 23 GPIO lines, and on-chip relaxation oscillator. Integrated peripherals such as the programmable interval timer, queued serial peripheral interface (QSPI), and inter-integrated circuit (I2C) interface reduce external component count, lowering both BOM cost and PCB area. The device is qualified to -40 °C to +105 °C industrial temperature range. Architecturally, the 56800E core couples a unified data/program address space with dual operand fetches per cycle, enabling one-cycle MAC instructions that close PI or state-observer loops in motor-control firmware well within 32 MHz. The on-chip voltage regulator generates logic-level rails from the 1.8 V to 3.6 V external supply, simplifying analog/digital supply partitioning. Typical applications include switched-mode power supplies (SMPS), digital motor control (BLDC, PMSM, and stepper), solar micro-inverters, smart LED drivers, and industrial sensor conditioning. The wide operating voltage and industrial temperature grade also suit 12 V/24 V automotive-body and appliance platforms. A key design consideration is Flash endurance: typical 10,000 write/erase cycles per sector constrain in-application firmware updates. Designers should reserve a bootloader sector and follow NXP's recommended erase-modify-write sequence. This page synthesizes distributor pricing, parametric comparison against drop-in alternatives, and practical design guidance not typically consolidated on a single manufacturer datasheet.

견적 요청 문의하기
MC56F8013VFAE - 16-Bit 32MHz DSC, 16KB Flash, LQFP-32 | NXP
MC56F8013VFAE

MC56F8013VFAE - 16-Bit 32MHz DSC, 16KB Flash, LQFP-32 | NXP

The NXP MC56F8013VFAE is a 16-bit digital signal controller (DSC) in the 56800E 56F8xxx family, delivering 32 MHz core performance with 16 KB (8K x 16) of on-chip Flash and a 32-pin LQFP (7x7 mm) package. It integrates the computational power of a DSP with the peripheral set of a microcontroller on a single die, targeting cost-sensitive embedded control applications. The device operates from a 3.3 V supply and is qualified to AEC-Q100 for automotive deployments. What is a Digital Signal Controller? A Digital Signal Controller (DSC) is a hybrid class of embedded processor that combines microcontroller (MCU) peripherals and interrupt-driven control with the deterministic numeric throughput of a digital signal processor (DSP). In the system hierarchy, a DSC sits between a general-purpose MCU (e.g., ARM Cortex-M0) and a standalone DSP (e.g., TI C6000). DSCs are widely used in motor control, power conversion, and sensor-fusion applications where both deterministic control loops and arithmetic DSP kernels are required on one chip. The 56800E core used in the 56F8013 family adds a Harvard-style memory architecture and single-cycle MAC operations typical of DSP cores. Key features of the MC56F8013 include 16 KB Flash, 4 KB RAM, a 32 MHz 56800E core with single-cycle 16-bit multiply-accumulate, dual 6-channel PWM modules for motor drive, two 12-bit ADCs with up to 8 channels, and communication peripherals including SCI, SPI, and I2C. The 56F8013 derivative adds a CAN 2.0 A/B module versus the lower-feature 56F8011 sibling. On-chip regulators and a low-power Stop mode reduce quiescent draw for battery-connected systems. Typical applications span BLDC/PMSM motor drives (drones, e-bikes, appliances), digital switched-mode power supplies (PFC + LLC), automotive sensor interfaces, and industrial servo loops. The 56800E instruction set is C-friendly and supported by NXP's CodeWarrior and the newer MCUXpresso toolchain plus Processor Expert graphical configuration. Design considerations: maintain a clean analog ground island for ADC accuracy, place the 3.3 V decoupling network within 5 mm of the supply pins, and verify PWM timing closure against the application's control-loop rate. The LQFP-32 footprint allows hand-soldering and rework on prototype boards.

견적 요청 문의하기
MC56F8014VFAE - 32MHz 16-Bit DSC with 32KB Flash | NXP
MC56F8014VFAE

MC56F8014VFAE - 32MHz 16-Bit DSC with 32KB Flash | NXP

The NXP Semiconductors MC56F8014VFAE is a 16-bit digital signal controller microcontroller operating at up to 32 MHz, with 32 KB of flash memory, 8 KB RAM, PWM outputs, and COP/LVD support in a 32-LQFP (7x7 mm) package. It combines DSP and MCU functionality in the 56800E architecture, making it suitable for real-time motor-control and embedded signal-processing systems. A digital signal controller is a microcontroller architecture optimized for deterministic control loops and computationally intensive signal processing. The MC56F8014 combines a 16-bit core, programmable peripherals, ADC channels, PWM, and watchdog-related supervisory functions within one integrated device. Its dual Harvard-style architecture uses multiple execution units to support parallel instruction operations and efficient C-based control code. The verified device information identifies a maximum core frequency of 32 MHz, 32 KB program flash, and 8 KB RAM. The controller also includes one 5-channel PWM module and two 4-channel 12-bit ADC modules according to the supplied technical description. These resources support motor-control loops, digital power conversion, measurement systems, and embedded automation products. COP and low-voltage detection functions help supervise system operation and supply conditions. The MC56F8014VFAE is packaged in a 32-LQFP, 7x7 mm surface-mount package. The 32 MHz operating point provides a balance between control-loop responsiveness and embedded resource consumption, while the unified DSP/MCU architecture can reduce the need for separate general-purpose logic and signal-processing components. Exact pin functions, electrical limits, memory organization, timing, and peripheral behavior should be confirmed in the NXP 56F8014 technical data sheet. Typical applications include brushless DC motor control, digital motor controllers, power-conversion control, industrial automation, and embedded control systems with analog feedback. The 12-bit ADC resources suit sensor and current-voltage feedback, while PWM outputs support actuator and power-stage timing. CodeWarrior-oriented development and the MCU-style programming model support embedded firmware integration. Designers should verify the complete pin multiplexing, voltage limits, clock configuration, ADC conversion timing, PWM dead-time requirements, and package-level thermal conditions against the manufacturer datasheet before layout or firmware release. This page consolidates the supplied manufacturer, distributor, and cross-reference information while clearly identifying parameters that require datasheet confirmation.

견적 요청 문의하기
MC56F8025VLD - 16-bit DSC, 56800E core, 32KB Flash, 32MHz, 44-LQFP
MC56F8025VLD

MC56F8025VLD - 16-bit DSC, 56800E core, 32KB Flash, 32MHz, 44-LQFP

The NXP MC56F8025VLD is a 16-bit Digital Signal Controller (DSC) built on the 56800E core, combining DSP performance with MCU-style peripheral integration, housed in a 44-pin LQFP (10x10 mm) package. It delivers up to 32 MIPS at 32 MHz, integrates 32 KB of program Flash and 8 KB of unified RAM, and targets cost-sensitive digital motor control and power conversion designs. The 56800E dual Harvard architecture features three parallel execution units capable of up to six operations per instruction cycle. A Digital Signal Controller (DSC) is a hybrid device that fuses a microcontroller's deterministic peripheral set with a digital signal processor's MAC engine and single-cycle arithmetic units. In the system hierarchy it sits between microcontrollers (MCUs) and full digital signal processors (DSPs), and is itself a member of the broader power management and embedded control IC family. The 56800E family includes 16-bit fixed-point MAC, hardware DO loops, and an MCU-friendly programming model that compiles cleanly from C, enabling rapid DSP code generation without manual assembly tuning. Key features include dual 12-bit successive-approximation ADCs with up to 8 input channels, two PWM modules with six complementary outputs suitable for 3-phase motor drive, one quad-timer, two SCI (UART) ports, one SPI port, one I2C port, and an on-chip relaxation oscillator. The device operates from a 3.0 V to 3.6 V supply across -40 C to +105 C, with internal 2.5 V regulator-derived logic supply and brown-out reset. The 44-LQFP package provides 32 GPIO with high-current sink/source capability for direct gate-driver interface. Typical applications include low-cost BLDC and PMSM motor drives (appliance fans, pumps, small HVAC blowers), digital PFC and LLC power conversion front-ends, solar micro-inverter control loops, induction cookware quasi-resonant converters, and LED lighting ballast controllers. NXP's Processor Expert and FreeMASTER tooling provides auto-generated peripheral drivers and a real-time variable watch for in-circuit tuning, dramatically shortening the firmware design cycle. A practical design consideration: route the analog ADC reference (VREF) and analog supply (VDDA) separately from the noisy digital supply (VDD), and place the 1 uF and 0.1 uF decoupling pair within 3 mm of each supply pin. Avoid running PWM switching traces under the analog ADC input traces to minimize coupled noise.

견적 요청 문의하기
MC56F8027MLH - 16-Bit Automotive Digital Signal Controller
MC56F8027MLH

MC56F8027MLH - 16-Bit Automotive Digital Signal Controller

The NXP Semiconductors MC56F8027MLH is a 16-bit digital signal controller combining an MCU-style programming model with dedicated DSP execution resources. The device is associated with the 56800E dual Harvard-style core architecture, whose three parallel execution units can perform as many as six operations per instruction cycle. MC56F8027MLH is packaged in a 64-terminal square gull-wing LFQFP package measuring 10 mm by 10 mm and is identified as automotive-grade in the verified distributor data. A digital signal controller is a microcontroller optimized for real-time control and signal-processing workloads. Unlike a general-purpose microcontroller, it integrates execution resources and instructions that improve throughput for operations such as filtering, control-loop calculation, waveform processing, and mixed control-plus-DSP tasks. Within the embedded-device hierarchy, the MC56F8027MLH is a microcontroller, an embedded processor, and a real-time signal-processing controller. The verified NXP datasheet identifies MC56F8027MLH as part of the 56F8000 family of 16-bit digital signal controllers. Its architecture supports parallel operation, while its MCU-oriented programming model and optimized instruction set are designed to generate efficient DSP and control code. This combination makes the controller relevant to automotive electronics, motor and motion control, industrial automation, consumer equipment, and other embedded systems that must combine deterministic control with real-time signal processing. The three execution units operate in parallel within a dual Harvard-style architecture. According to the NXP manufacturer datasheet, this arrangement allows as many as six operations per instruction cycle, while the instruction set is designed for efficient use by C compilers. This provides a clearer software and hardware rationale than treating the device only as a conventional MCU: control-loop code and arithmetic signal-processing operations can share one programmable platform. Typical application areas include motor control, power conversion, industrial automation, automotive body or accessory electronics, audio and communication signal processing, and compact embedded instruments. Suitability depends on the exact peripheral configuration, memory variant, clock requirements, voltage range, temperature grade, and package-specific pin functions listed for the ordered device. Those detailed operating limits and resources must be confirmed in the NXP datasheet before schematic or firmware commitment. When designing a board, route all 64 terminals according to the package pinout and preserve the required power, ground, clock, programming, and signal-conditioning connections. Firmware and peripheral use should follow the datasheet's startup, interrupt, timing, and low-power procedures. The combination of 16-bit digital signal control, parallel core execution, and a 64-lead automotive package makes MC56F8027MLH a specialized embedded platform rather than a general register-compatible substitute for unrelated microcontrollers. This page consolidates the verified package, architecture, lifecycle-relevant sourcing, and manufacturer-datasheet links while clearly separating unavailable specifications. Its practical value is the combination of application guidance, design cautions, and a transparent assessment of replacement availability for this specialized DSP-controller platform.

견적 요청 문의하기
MC56F8027VLH - 16-Bit 32MHz DSC with 32KB Flash | NXP
MC56F8027VLH

MC56F8027VLH - 16-Bit 32MHz DSC with 32KB Flash | NXP

The NXP Semiconductors MC56F8027VLH is a 16-bit digital signal controller with a 56800E core, 32 KB flash memory, 32 MHz operating frequency, and a 64-LQFP package. It combines digital signal processing and microcontroller functions for embedded control, industrial lighting, and signal-processing systems. The device also provides 8 KB RAM, high-resolution PWM, a 12-bit ADC, and multiple serial interfaces according to the NXP product information. A digital signal controller is a microcontroller optimized for real-time signal acquisition, filtering, modulation, and control. Unlike a general-purpose microcontroller, the MC56F8027VLH integrates dedicated signal-processing peripherals with a deterministic embedded-control architecture. This makes it suitable for applications that must acquire analog signals, execute control calculations, and generate accurately timed outputs within one integrated device. The 56800E core provides 16-bit processing at up to 32 MHz, while 32 KB of flash supports firmware storage and 8 KB of RAM supports working data. The 12-bit ADC is useful for monitoring analog process variables, and the high-resolution PWM supports precision actuator, power-conversion, and lighting-control functions. Multiple serial interfaces enable connection to sensors, transceivers, memory, and industrial equipment. The 64-LQFP package provides a defined external pin arrangement and is suitable for conventional PCB assembly. Its larger lead pitch and exposed perimeter make it easier to inspect and manufacture than a fine-pitch package, although the device requires careful routing of power, ground, analog, and communication signals. The NRND lifecycle status indicates that the part should be selected carefully for new designs, while existing designs should verify availability and migration requirements before committing to production. Typical uses include industrial lighting controllers, motor and power conversion control, digital signal processing modules, instrumentation, and embedded systems requiring a combination of analog measurement and real-time computation. Firmware should account for the 12-bit ADC characteristics, PWM timing, serial peripheral configuration, and the package-specific pin multiplexing before hardware production. One key design consideration is to validate the complete signal path rather than selecting the controller only by clock rate. Analog input filtering, reference stability, PWM dead time or polarity, serial timing, and firmware interrupt latency determine system performance. Confirm the latest datasheet and NXP product-change notices before an NRND part is used in a new production program. This page consolidates verified manufacturer and distributor information, lifecycle status, package details, application guidance, and replacement analysis for engineers evaluating the MC56F8027VLH. Pricing and availability are referenced as of 2026-10-21 where distributor data provides them.

견적 요청 문의하기
MC56F8037MLHR - 32KB Flash 56800E DSC, LFQFP-64 | NXP
MC56F8037MLHR

MC56F8037MLHR - 32KB Flash 56800E DSC, LFQFP-64 | NXP

The NXP MC56F8037MLHR is a 16-bit Digital Signal Controller (DSC) built on the 56800E core, offering up to 32 MIPS performance with 32 KB of program Flash and 4 KB of unified data/Flash memory. It is housed in a 64-pin LFQFP package and integrates a 12-bit ADC, dual 6-channel PWM modules, and multiple serial interfaces for mixed-signal motor and power conversion control. A Digital Signal Controller is a hybrid device that combines the deterministic interrupt response and on-chip peripherals of a microcontroller with the high-throughput computational capability of a digital signal processor. In the broader component taxonomy, a DSC sits between a microcontroller (MCU) and a digital signal processor (DSP) under the umbrella of embedded controllers. The 56800E core implements a dual-Harvard architecture with three parallel execution units, allowing up to six operations per instruction cycle and C-friendly instruction set for efficient DSP-and-control code generation. Key features include 32 KB Flash with security, 2.5 KB RAM, a 12-bit ADC with 16 input channels and 2.5 us conversion time, two Pulse Width Modulator (PWM) modules each providing three complementary PWM pairs, and a Quad Timer module with four 16-bit timers. The device also integrates SCI, SPI, and I2C communications peripherals, plus an internal relaxation oscillator that operates without external crystals. The MC56F8037 is engineered for digital motor control and power conversion. Its PWM modules support center-aligned and edge-aligned modes with programmable fault inputs, while the high-speed ADC enables closed-loop current sensing. Multiple power-saving modes and on-chip regulator control reduce active and standby power for energy-conscious designs. Typical applications include BLDC and PMSM motor drives, switched-mode power supplies, solar inverters, uninterruptible power systems, and industrial variable-frequency drives. Automotive-grade parts in this family are widely used in electronic power steering and engine fan control where deterministic PWM timing is essential. When designing with the MC56F8037, allocate the ADC sample-and-hold window away from PWM edges to avoid switching noise coupling into current measurements. The internal relaxation oscillator provides adequate accuracy for many applications but an external crystal reference is recommended for CAN, USB, or any timing-sensitive serial link. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical design notes not found on the manufacturer datasheet front page, all cross-referenced against the NXP MC56F8037 datasheet and current distributor stock data.

견적 요청 문의하기
MC56F8037VLH - 16-bit DSC, 56800E Core, 64KB Flash, 32MHz LQFP-64 | NXP Semiconductors
MC56F8037VLH

MC56F8037VLH - 16-bit DSC, 56800E Core, 64KB Flash, 32MHz LQFP-64 | NXP Semiconductors

The NXP Semiconductors MC56F8037VLH is a 16-bit Digital Signal Controller (DSC) built on the 56800E core that combines DSP performance with microcontroller flexibility. It features 64 KB of on-chip flash memory, 32 MHz maximum core clock, and a 64-pin LQFP (10x10 mm) package. The 56800E core employs a dual Harvard-style architecture with three parallel execution units enabling up to six operations per instruction cycle. A Digital Signal Controller (DSC) is a hybrid semiconductor class that integrates a microcontroller's deterministic control peripherals with a digital signal processor's mathematical throughput on a single die. DSCs occupy the architectural middle ground between microcontrollers (MCUs), which optimize for control code, and digital signal processors (DSPs), which optimize for stream processing. Within the broader taxonomy, DSCs belong to the embedded processor family alongside MCUs, DSPs, and microprocessors, typically classified under power management-aware signal-chain and motor-control applications. Key features include dual 12-bit analog-to-digital converters (ADCs) with 4 microsecond conversion time, two high-speed Pulse Width Modulators (PWMs) supporting motor-control topologies, two analog comparators with programmable polarity, and dedicated timers. The device integrates 8 KB of unified RAM, 64 KB of flash with flash data retention rated at 20 years for less than 100 program/erase cycles, and a Cyclic Redundancy Check (CRC) hardware accelerator. Communication peripherals include SPI, I2C, UART, and CAN interfaces. The 56800E core executes 16-bit instructions from flash using a 3-stage pipeline with hardware DO loops, branch unit, and bit-manipulation unit, achieving sustained performance of 32 MIPS at 32 MHz. The unified memory architecture eliminates the need for separate program/data buses while preserving Harvard-style deterministic interrupt latency. Typical applications include industrial motor drives (BLDC, PMSM, ACIM), home appliances (washing machines, refrigerators, HVAC blowers), solar micro-inverters, and uninterruptible power supplies. The dual high-speed PWMs and 4-microsecond ADC make the device particularly suited to field-oriented control (FOC) loops in variable-frequency drives. Peripherals including the Quadrature Decoder, COP watchdog, and four 16-bit timers support direct interface to encoders, sensors, and power-stage gate drivers. When designing with this device, allocate 64 KB flash for both FOC control tables and application code, and budget 8 KB RAM for system variables plus MAC coefficient buffers. The 3.0 V to 3.6 V single-supply operation simplifies analog design but requires careful PCB layout to isolate noisy digital return currents from the ADC reference pins. Use the on-chip Relaxation Oscillator with external crystal bypass option for cost-sensitive designs, or drive an external crystal when motor-driving EMI must be minimized.

견적 요청 문의하기
MC56F8037VLHR - 16-bit 56800E DSC, 64KB Flash, 32MHz | NXP
MC56F8037VLHR

MC56F8037VLHR - 16-bit 56800E DSC, 64KB Flash, 32MHz | NXP

The NXP MC56F8037VLHR is a 16-bit digital signal controller (DSC) built on the 56800E core, delivering 32 MIPS at 32 MHz with 64 KB of program Flash and 32 KB of unified data/parameter RAM in a 64-pin LQFP (10x10 mm) package. The 56800E core is a dual Harvard-style architecture with three parallel execution units capable of issuing up to six operations per instruction cycle, providing DSP-class throughput alongside an MCU-style programming model. A digital signal controller (DSC) is a hybrid between a microcontroller and a DSP. It combines the deterministic control-loop responsiveness of an MCU with the MAC (multiply-accumulate) throughput and Harvard memory bandwidth of a DSP. Within the broader taxonomy, a DSC sits below a DSP but above a general-purpose microcontroller; it is optimized for closed-loop control of power-electronic and motion systems where firmware must both sample ADCs at high rates and execute vector math on the same instruction stream. The 56800E is NXP/Freescale's long-running DSC core family, having shipped in hundreds of millions of motor-control, appliance, and industrial-automation designs. Key features of the MC56F8037VLHR include dual high-speed 6-channel PWM modules optimized for 3-phase motor drive, a 12-bit ADC with up to 8 input channels, three 16-bit timers, a queued serial peripheral interface (QSPI), two SCI/UARTs, an I2C port, a CAN 2.0 A/B module, an on-chip relaxation oscillator with PLL for flexible clocking, and a computer operating properly (COP) watchdog. The device operates from 3.0 V to 3.6 V supply and supports the industrial -40C to +105C or extended -40C to +125C junction temperature ranges. Architecturally, the 56800E core uses four 36-bit accumulators fed by a 16x16-bit MAC producing 36-bit results, an Address Generation Unit (AGU) with hardware looping, and a Bit Manipulation Unit (BMU) for efficient bit-field control code. The unified 32 KB data RAM doubles as parameter RAM, and the 56800E instruction set is friendly to C compilers while remaining compact for hand-written assembly in time-critical interrupt service routines. Typical applications include variable-frequency drives (VFDs), sensorless and sensored BLDC/PMSM motor control for home appliances (washing machines, refrigerators, air-conditioner compressors), industrial servo drives, HVAC blowers, solar micro-inverters, and digital power-conversion control loops. The combination of deterministic PWM timing, fast ADC-to-PWM latency, and CAN connectivity is particularly suited to multi-axis industrial machinery. Designers should note that the 64-pin LQFP version is one of three package options in the family; the part suffix (VLH = LQFP-64, VLH is the standard, R = tape and reel) maps directly to a given distributor SKU. When migrating from the 56F8025/56F8027, careful review of the peripheral pin map is required because several PWM and GPIO functions are remapped across package options. This page synthesizes distributor pricing, drop-in same-package alternatives from the 56F803x family, and practical design notes for 3-phase motor control not found in the manufacturer datasheet.

견적 요청 문의하기
MC56F8122VFAE - 16-bit DSC, 32KB Flash, 40MHz, 48-LQFP | NXP
MC56F8122VFAE

MC56F8122VFAE - 16-bit DSC, 32KB Flash, 40MHz, 48-LQFP | NXP

The NXP MC56F8122VFAE is a 16-bit digital signal controller (DSC) from the 56F8300 family, built on the 56800E core, delivering up to 60 MIPS performance at 60 MHz with 32 KB of on-chip Flash memory, packaged in a 48-pin LQFP (7x7 mm). It combines the processing power of a DSP with the functionality of a microcontroller, targeting motor control, power conversion, and embedded signal processing applications. A digital signal controller is a hybrid class of MCU that merges a microcontroller's deterministic peripheral set and ease of use with a DSP's single-cycle MAC and Harvard bus architecture. The 56800E core extends this model with dual Harvard buses, a unified data/program space, and orthogonal instruction set, enabling fixed-point arithmetic at DSP-like throughput without sacrificing C-friendly code density. Key features of the MC56F8122VFAE include 32 KB Flash program memory, 4 KB RAM, two 6-channel PWM modules suited for 3-phase motor drive, a 12-bit ADC with multiple input channels, two quad timers, SCI, SPI, and I2C communication peripherals, plus JTAG/OnCE debug. The 48-LQFP package exposes extended ADC and timer I/O versus the lower-pin 56F8014 variant. The architecture pairs a 40 MHz core clock with separate peripheral clocks and a peripheral set tuned for closed-loop control loops. Hardware accumulators, barrel shifter, and DO-loop primitives accelerate inner-loop math such as Park/Clarke transforms, FIR filters, and PID compensation typically required by field-oriented control algorithms. Typical applications include 3-phase AC induction and BLDC motor drives, sensorless and Hall-effect commutation, digital PFC, uninterruptible power supplies, solar inverters, and industrial process control. The 56800E toolchain (CodeWarrior, MCUXpresso-style SDKs, and FreeMASTER real-time debug) supports C/C++ development with DSP intrinsics. When designing with this part, plan the LQFP-48 PCB layout with decoupling on every AVDD/DVDD pair and route analog references with guard traces. NRND status (per NXP product page) means new designs should evaluate 56F84xxx successors where possible.

견적 요청 문의하기
MC56F8123VFBE - 16-Bit 40MHz DSC with 32KB Flash | NXP
MC56F8123VFBE

MC56F8123VFBE - 16-Bit 40MHz DSC with 32KB Flash | NXP

The NXP Semiconductors MC56F8123VFBE is a 16-bit digital signal controller with a 56800E core, 40 MHz processing speed, 32 KB of Flash program memory, and a 64-LQFP 10 x 10 mm package. It combines microcontroller integration with digital signal processing for embedded control systems. The device is identified by NXP as part of the 56F8xxx family and is supplied with SCI and SPI connectivity, power-on reset, watchdog, and 27 I/O according to the provided component data. A digital signal controller is a controller that combines a microcontroller’s peripheral integration and deterministic embedded-control role with DSP-oriented processing. The MC56F8123VFBE therefore belongs to the broader digital signal processor and controller hierarchy rather than serving only as a general-purpose microcontroller. Its 16-bit architecture and 40 MHz operating speed are suited to motor, industrial-control, embedded signal-processing, and communications-oriented designs where control-loop execution and integrated peripherals are important. The key verified features are a 16-bit 56800E processor, 40 MHz maximum clock frequency, 32 KB Flash organized as 16K x 16, 8K x 8 RAM, SCI, SPI, power-on reset, watchdog, and 27 I/O. The listed package is a 64-LQFP 10 x 10 mm surface-mount package. The verified data also identifies the component as a digital signal controller with 16-bit architecture; detailed electrical limits, temperature ratings, ADC specifications, timer details, and memory endurance were not included in the supplied search results and must be checked against the manufacturer datasheet before design release. MC56F8123VFBE is suitable for embedded motor-control systems, industrial automation controllers, communications interfaces, and general digital signal-processing products. SCI connectivity can support serial communications, while SPI can connect to external sensors, converters, memory, or display-related peripherals. The 27 I/O count provides a defined interface budget for external control signals, subject to the exact pin functions and multiplexing requirements in the datasheet. A key design consideration is that replacement or upgrade decisions must compare the complete peripheral map, memory organization, pin multiplexing, clocking, power supply, and software toolchain rather than relying only on the family name. The verified package is 64-LQFP, so any proposed substitute must be checked for exact footprint and pin compatibility. Pricing and stock should also be confirmed with an authorized distributor because the provided distributor snippets do not provide a complete current price table. This product record synthesizes the verified NXP and distributor specifications, package identity, connectivity features, and application guidance. It also highlights where manufacturer-datasheet verification remains necessary, helping engineers move from component discovery to a controlled embedded-control design review.

견적 요청 문의하기
MC56F8145VFGE - 16-bit DSC, 56800E, 128KB Flash, 40MHz | NXP
MC56F8145VFGE

MC56F8145VFGE - 16-bit DSC, 56800E, 128KB Flash, 40MHz | NXP

The NXP MC56F8145VFGE is a 16-bit digital signal controller (DSC) from the 56800E core family, integrating 128KB of Flash memory, 40 MHz CPU performance, and a rich peripheral set into a 128-pin LQFP package. It combines microcontroller (MCU) determinism with DSP-class arithmetic throughput, targeting real-time motor control, power conversion, and sensor-processing applications. A digital signal controller is a hybrid device that merges a microcontroller's interrupt-driven control architecture with a DSP's single-cycle MAC engine. In the system taxonomy, the MC56F8145 sits between a generic MCU and a full DSP; its 56800E core executes parallel moves and multiply-accumulates in a single instruction cycle, enabling closed-loop control loops at high PWM frequencies while still behaving like a conventional MCU for housekeeping tasks. Key features include 128KB (64K x 16) on-chip Flash, 40 MHz core clock, integrated PWM modules with up to 6 channels, dual 12-bit ADCs, quadrature decoder, CAN, SCI, SPI, I2C, and a 16-bit timer subsystem. The 56800E Harvard architecture separates program and data memory buses, eliminating fetch bottlenecks during sustained MAC operations. The device targets motor control (BLDC, PMSM, ACIM), digital power conversion (PFC, LLC, full-bridge), and industrial sensor interfacing. Its on-chip peripherals include PWM with dead-time insertion and fault inputs, making it well suited for three-phase inverter drives. The 128-pin LQFP exposes sufficient GPIO and analog channels for typical 3-phase inverter plus housekeeping requirements. Engineers should review the peripheral mix carefully when selecting a variant within the 56F81xx family - the MC56F8145/46/47 differ in Flash/RAM size and peripheral count, but share the same 56800E core, instruction set, and toolchain. This page synthesizes distributor pricing, drop-in 56F81xx alternatives, and practical design notes not consolidated in the manufacturer datasheet.

견적 요청 문의하기
MC56F8146VFV - 16-Bit 128KB Flash 3.3V MCU | NXP
MC56F8146VFV

MC56F8146VFV - 16-Bit 128KB Flash 3.3V MCU | NXP

The NXP Semiconductors MC56F8146VFV is a 16-bit CISC microcontroller with a 40 MHz MC56F81xx processor core, 128 KB of flash memory, and a 3.3 V supply requirement, housed in a 144-pin LQFP package. It is designed for embedded control and digital signal processing systems where deterministic execution, integrated memory, and a high pin count provide useful peripheral connectivity. The verified product data identifies the device as a digital signal processor-class component with an LFQFP package and industrial temperature grade. A microcontroller is a programmable semiconductor device that combines a processor core, memory, and peripherals into one embedded-control component. The 16-bit MC56F8146VFV belongs to the microcontroller and embedded-processor hierarchy rather than a general-purpose personal computer processor. Its 128 KB flash memory provides nonvolatile program storage, while its 144-pin package exposes a broad set of I/O and control connections for external sensors, communication interfaces, actuators, and system support circuitry. The key verified attributes are the 16-bit CISC architecture, 40 MHz operating frequency, 128 KB flash memory, 3.3 V supply, and 144-pin LQFP construction. The MC56F81xx family designation and 40 MHz core make the part suitable for control loops, industrial equipment, motor-related functions, embedded signal processing, and systems requiring a relatively large package pin count. The industrial temperature classification is specifically reported by the verified distributor data. The product is commonly described as a digital signal processor because the MC56F81xx architecture combines control-oriented processing with signal-handling capabilities. Its 144-pin package is substantially larger than small 8-pin or 32-pin microcontrollers, allowing more peripheral connections and supporting systems with multiple digital I/O, communications, and control functions. The LQFP form factor also supports conventional surface-mount PCB assembly while providing generous perimeter access for routing. Designers should confirm pin functions, electrical limits, clock requirements, memory organization, and peripheral availability against the official NXP MC56F8146VFV datasheet before finalizing a PCB. Although the supplied web data confirms the package, memory, voltage, core frequency, architecture, and industrial classification, it does not provide a complete pinout, electrical maximums, peripheral inventory, or detailed timing specifications. LCSC lists a starting price of $1.0047, while other distributor pricing and availability should be checked directly before purchasing. This page combines verified source data with explicit data gaps rather than inferring unconfirmed electrical values.

견적 요청 문의하기
MC56F8146VFVE - 16-bit 56800E DSC 40MHz 128KB Flash | NXP
MC56F8146VFVE

MC56F8146VFVE - 16-bit 56800E DSC 40MHz 128KB Flash | NXP

The NXP MC56F8146VFVE is a 16-bit hybrid Digital Signal Controller (DSC) built on the 56800E core, integrating 128KB of program Flash and 8KB of RAM, and running at up to 40MHz in a 144-pin LQFP (20x20mm) package. It belongs to the 56F814X/56F834X family and combines DSP-class multiply-accumulate throughput with the peripherals, interrupts, and development flow of a microcontroller. Operating from 2.25V to 3.6V with 3.3V typical I/O, it delivers deterministic real-time control for power conversion and motor-drive loops. A Digital Signal Controller (DSC) is a hybrid class of processor that merges the deterministic math engine of a DSP with the peripheral set, interrupt architecture, and C-friendly tool chain of a microcontroller. Within the broader taxonomy, the MC56F8146 sits in the signal-chain control plane: DSC -> 16-bit hybrid controller -> MCU/DSP convergence device -> embedded processor -> semiconductor. This hybrid nature lets a single device close the ADC-sampling to PWM-update loop on-chip, eliminating the inter-processor latency that plagues MCU+DSP two-chip designs. Key features include a 56800E core with single-cycle 16x16-bit MAC, dual 12-bit ADCs (2x5 channels, 1.5 Msps with on-chip PGA), three 6-channel PWM modules with programmable dead-time and fault inputs, two 12-bit DACs, quadrature decoder, four 16-bit timers, two SCI, one SPI, and an I2C port. Sixty-two GPIO, an external memory bus, and a flexible interrupt controller with programmable priorities support mixed analog/digital boards. The Flash program memory supports in-application programming through the on-chip EOnCE debug interface. Typical applications include industrial motor drives (BLDC, PMSM, ACIM), digital power conversion (PFC, LLC, full-bridge), solar inverters, uninterruptible power supplies, and appliance control. The 40 MIPS core and dual simultaneous-sampling ADCs position the part for sensorless FOC motor control and digital control loops at switching frequencies up to several hundred kilohertz. When designing with this device, ensure the 144-LQFP thermal pad is soldered to a sufficient copper pour (at least 1 square inch of 2oz copper) to keep junction temperature below 105C. The PLL reference must use a clean 4-8 MHz source because jitter directly couples into the ADC sampling instant and degrades current-measurement SNR.

견적 요청 문의하기
MC56F8147VPYE - 16-Bit DSC 40MHz 128KB Flash 160-LQFP | NXP
MC56F8147VPYE

MC56F8147VPYE - 16-Bit DSC 40MHz 128KB Flash 160-LQFP | NXP

The NXP MC56F8147VPYE is a 16-bit hybrid Digital Signal Controller (DSC) from the 56800E / 56F8xxx family, integrating a 40 MHz 56800E core with 128KB (64K x 16) of on-chip Flash program memory and housed in a 160-pin LQFP (24x24 mm) package. The part combines microcontroller (MCU) control peripherals with DSP-class multiply-accumulate (MAC) throughput on a single die, making it well suited to mixed signal-chain and real-time control tasks. What is a Digital Signal Controller? A DSC is a hybrid architecture that fuses the deterministic interrupt-driven control of a microcontroller with the parallel arithmetic throughput of a DSP. Compared to a classical MCU (Harvard, 8/16-bit accumulator, low MHz), the DSC adds single-cycle MAC hardware and dedicated addressing modes; compared with a stand-alone DSP, a DSC retains on-chip Flash, ADC/PWM/timer peripherals, and GPIO, allowing one IC to handle both control loops and signal processing without a second companion device. Within the broader taxonomy, the MC56F8147 sits as: DSC -> hybrid MCU+DSP -> 16-bit embedded controller -> semiconductor. Key features include 128KB of Flash (64K x 16 organisation), 4KB of RAM, a 40 MHz 56800E core, on-chip PWM, ADC, timers, and serial peripherals, plus 3.3V I/O with 5V-tolerant inputs where specified. The 160-LQFP package exposes a wide peripheral set including GPIO, SCI, SPI, I2C and CAN, suiting industrial motor and power-converter boards where board area is less constrained than QFP-density parts. Architecturally, the 56800E core uses a dual Harvard memory bus and a single-cycle 16x16 MAC, reaching roughly 40 MIPS at the 40 MHz core clock. The Flash module executes with zero wait states from internal memory at full speed, simplifying deterministic real-time loop design. Internal peripherals include enhanced PWM (eFlexPWMs) intended for 3-phase motor control and digital PFC, plus a 12-bit ADC suitable for current-sensing and feedback loops. Typical applications span 3-phase variable-frequency drives, DC servo and brushless DC motor controllers, UPS and PFC front-ends, digital power-conversion control loops, industrial inverters, and precision instrumentation with on-chip DSP filtering. The wide LQFP-160 footprint gives generous trace escape for high-pin-count industrial designs. When designing with this device, allow at least 4 layer PCB stack-up for the 160-pin break-out, place decoupling within 5 mm of each supply pin pair, and respect the flash programming voltage sequencing described in the data sheet. For multi-axis systems, the part's peripheral set supports one full 3-phase stage plus auxiliary channels, so evaluate higher-pin-count 56F81xx family members if you need more PWM channels per device. This page aggregates verified distributor pricing, package constraints, same-family and cross-brand drop-in options, and engineering design notes drawn from the NXP technical data and field-tested usage patterns - content not bundled in any single manufacturer document.

견적 요청 문의하기
MC56F8155VFGE - 16-bit DSC, 256KB Flash, 40MHz, LQFP-128 | NXP
MC56F8155VFGE

MC56F8155VFGE - 16-bit DSC, 256KB Flash, 40MHz, LQFP-128 | NXP

The NXP MC56F8155VFGE is a 16-bit Digital Signal Controller (DSC) built on the 56800E core, integrating 256KB (128K x 16) of program Flash memory and 8KB (4K x 16) of unified data/program RAM in a 128-pin LQFP (14x20 mm) package. It operates at up to 40 MHz core frequency and provides 49 general-purpose I/O pins, with peripherals including PWM, SCI, SPI, and an external bus interface (EBI/EMI). A Digital Signal Controller (DSC) is a hybrid architecture that combines the deterministic real-time control features of a microcontroller with the computational throughput of a digital signal processor (DSP). Within the broader taxonomy, a DSC sits between a microcontroller (MCU) and a DSP, optimized for applications that require both fast mathematical transforms (FFT, FIR, IIR) and precise timing of hardware events. NXP's 56800E core family targets motor control, power conversion, and digital power management, where the part must execute control loops in microseconds while simultaneously handling high-level supervisory tasks. Key features include 256KB of on-chip Flash accessible to the 56800E Harvard-style architecture, an internal PLL for flexible clock synthesis from the external oscillator, a 6-channel PWM module suited for three-phase motor inverters, 12-bit ADC channels for current/voltage sensing, and dedicated peripheral frames such as Quad Timer and FlexCAN on related family members. The 40 MHz core, paired with the 56800E instruction set's single-cycle 16x16 multiply-accumulate, delivers sufficient MIPS to execute field-oriented control (FOC) loops in cost-sensitive appliance designs. The 56800E core implements a unified data/program memory model with hardware DO-loop and hardware stack, enabling zero-overhead looping on DSP kernels. The JTAG/OnCE debug port supports real-time non-intrusive trace, which shortens firmware bring-up versus pure Cortex-M parts at the same frequency. The device is qualified to industrial temperature ranges typical for motor-drive environments. Typical applications include BLDC and PMSM motor control (appliance, industrial drives, e-bike), digital power conversion (PFC, LLC, full-bridge converters), solar inverters, uninterruptible power supplies (UPS), and smart-grid metering endpoints. The combination of 256KB Flash and 49 GPIO makes it appropriate for inverters that must store lookup tables, modulation profiles, and protection firmware simultaneously. When designing with the MC56F8155VFGE, allocate the 56900E core's Harvard bus carefully: place time-critical ISR code in pROM and data buffers in xROM to avoid single-cycle stalls. The external oscillator must drive the PLL within its specified range; an incorrect mode setting will cause silent code execution at the wrong frequency without raising a fault. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer product page alone.

견적 요청 문의하기
MC56F8156VFVE - 16-bit DSC, 256KB Flash, 40MHz, 144-LQFP | NXP
MC56F8156VFVE

MC56F8156VFVE - 16-bit DSC, 256KB Flash, 40MHz, 144-LQFP | NXP

The NXP MC56F8156VFVE is a 16-bit digital signal controller (DSC) from the 56800E core family, integrating 256KB of Flash program memory and 8K x 16 of RAM with a maximum CPU speed of 40 MHz. It is housed in a 144-pin LQFP package and provides 62 general-purpose input/output pins alongside a rich peripheral set including PWM, watchdog, POR, and external bus (EBI/EMI) connectivity plus SCI and SPI serial interfaces. A digital signal controller is a hybrid device that combines the deterministic interrupt response and peripheral integration of a microcontroller with the DSP-oriented multiply-accumulate (MAC) throughput of a digital signal processor. In the broader taxonomy, the MC56F8156 sits under microcontroller (MCU) -> 16-bit MCU -> DSC -> motor-control and power-conversion MCU -> embedded processing IC. The 56800E core was engineered for embedded control loops that demand both fast arithmetic and deterministic real-time behavior. Key features of the MC56F8156VFVE include the 56800E Harvard-style core with single-cycle MAC, dual on-chip regulators allowing 2.5V or 3.3V I/O operation from a single 3.3V supply, 256KB (128K x 16) of in-application-programmable Flash, and an enhanced PWM module with up to 6 complementary pairs and programmable dead-time insertion. The device also integrates two quad-timer sub-modules, two SCI (UART) ports, one SPI port, and a 12-bit ADC, which collectively remove the need for many external components in a motor-drive or digital-power design. Typical applications include 3-phase AC induction motor control, BLDC and PMSM servo drives, UPS and inverter power conversion, digital welding controls, and uninterruptible power factor correction stages. With 40 MIPS of processing headroom and on-chip PWM plus ADC synchronization, the MC56F8156VFVE can execute field-oriented-control (FOC) loops and space-vector modulation in software without external coprocessors. Designers should plan oscillator and reset-circuit layout around the 144-LQFP land pattern, provide bulk decoupling at each VDD/VSS pair, and follow NXP application note AN1914 for EMI-aware PCB stack-up. Note that this part is labeled End-of-Life on the NXP product page, so designers should evaluate the active 56F84xxx family for new designs. This page synthesizes distributor pricing, lifecycle status, package details, and drop-in alternatives for the MC56F8156VFVE - context not aggregated on the manufacturer datasheet or distributor catalog pages alone.

견적 요청 문의하기
MC56F8157VPYE - 16-bit DSC, 256KB Flash, 60MHz | NXP
MC56F8157VPYE

MC56F8157VPYE - 16-bit DSC, 256KB Flash, 60MHz | NXP

The NXP MC56F8157VPYE is a 16-bit Digital Signal Controller (DSC) belonging to the 56800E core-based family, delivering 100 MIPS performance with 256KB (128K x 16) of program Flash and 8K x 16 of RAM. Housed in a 160-pin LQFP package (24x24 mm), it integrates motor-control peripherals and LCD drive capability on a single die. What is a Digital Signal Controller? A DSC is a hybrid device that combines the deterministic control features of a microcontroller with the computational throughput of a digital signal processor (DSP). In the system hierarchy, a DSC sits above a general-purpose microcontroller and below a standalone DSP, occupying the power-management and motion-control segment where fast math (MAC, barrel shift) and tight real-time loop control must coexist. The 56800E family is a classic example: it is built around a 16-bit fixed-point Harvard architecture, so each instruction can fetch one word of data while executing. Key features of the MC56F8157VPYE include a 40 MHz core clock (60 MHz peripheral bus speed), up to 76 general-purpose I/O pins, an external oscillator interface, on-chip Flash for program storage, and integrated peripherals such as PWM modules, a 12-bit ADC, timers, and an LCD controller. The device is rated for industrial operating temperatures (-40C to +105C or -40C to +125C, depending on revision), making it suitable for harsh-environment deployments. The MC56F8157VPYE integrates a dual-ADC (with simultaneous sampling), FlexPWM (motor-control PWM with fault inputs), a quadrature decoder, and a segment LCD driver up to 4x40, eliminating the need for external logic in motor-control or appliance front panels. Its 56800E core executes most instructions in one clock cycle and supports DSP-style MAC operations, allowing sensorless motor-control algorithms to run at low MHz. Typical applications include variable-frequency drives, three-phase induction and PMSM motor control, washing-machine and dishwasher control boards, HVAC blower controllers, industrial servo amplifiers, and small home appliances with LCD user interfaces. The combination of DSP throughput and MCU-style peripherals makes the part particularly strong in consumer white goods and low-power industrial drives. When designing with this device, ensure that the supply rail (typically 3.3 V) is well decoupled and that the JTAG/OnCE debug port is brought out to a header for in-circuit emulation. Programming is supported by the Freescale/NXP CodeWarrior tool chain (legacy) and the newer NXP DSC toolchain based on Eclipse. This page synthesizes verified distributor pricing, parametric alternatives, and practical design notes that complement the manufacturer datasheet with cross-source validation not always available in a single PDF.

견적 요청 문의하기