RF 및 무선
하위 카테고리
제품 (661)
SIGFOX-MOD1-E - 868MHz Sigfox RF Transceiver Module | XoverIoT
The XoverIoT SIGFOX-MOD1-E is a certified sub-GHz RF transceiver module designed for bi-directional Sigfox network communication in the 868 MHz ISM band, integrating the Sigfox protocol stack and AT-command firmware on an STMicroelectronics STM32L051 microcontroller. The module is supplied in a surface-mount form factor with an external antenna connector (U.FL) variant for flexible antenna placement in IoT end-products. A Sigfox modem (also called a 0G network transceiver module) is a pre-certified radio device that handles physical-layer modulation, regional frequency compliance, and the proprietary Sigfox ultra-narrowband (UNB) protocol so that integrators do not need to design an RF chain from scratch. The category sits within the broader RF & Wireless > RF Modules hierarchy (RF Modules > wireless modules > transceivers > sub-GHz modules > IoT modems) and is one of several LPWAN connectivity options including LoRa, NB-IoT, and LTE-M. The SIGFOX-MOD1-E occupies the lowest-power end of this category, targeting battery-operated sensors that transmit small payloads (typically 12 bytes uplink, 8 bytes downlink) a few times per hour and operate for years on a single primary cell. Key features include Sigfox-verified firmware, an AT-command serial interface for rapid host MCU integration, an integrated sub-GHz RF front-end, bidirectional TX/RX capability for cloud-to-device messaging, and direct sensor interface options that reduce BOM by eliminating an external host processor. The module supports antenna diversity via the U.FL external connector. The SIGFOX-MOD1-E is built around the STMicroelectronics STM32L051 ultra-low-power ARM Cortex-M0+ microcontroller combined with a sub-GHz sub-GHz transceiver front end, delivering the verified Sigfox protocol stack with reliable long-range coverage. The architecture uses ultra-narrowband modulation with bit rates in the hundreds of bits per second, achieving sensitivity typical of -126 dBm in RCZ1 regions. Typical applications include IoT sensor devices, low-power battery-operated remote monitoring, smart metering, asset tracking, environmental monitoring, and any deployment requiring bidirectional ultra-low-power wide-area network connectivity. When designing with this module, ensure that the external antenna is matched to 50 ohms and placed clear of ground planes and battery shielding. The AT-command firmware enables the module to act as a modem attached to a host MCU via UART, which dramatically reduces firmware development time. This page synthesizes distributor pricing, drop-in Sigfox alternative modules, and practical RF design notes not found in the manufacturer datasheet.
SIM68M - GPS GLONASS Galileo GNSS Module | SIMCom
The SIMCom SIM68M is a high-performance stand-alone GNSS receiver module supporting simultaneous GPS, GLONASS, Galileo and QZSS L1 reception with 33 tracking channels and 99 acquisition channels, tracking sensitivity down to -165 dBm, in a compact 18-pin SMT LCC package without integrated antenna. A GNSS (Global Navigation Satellite System) module is an RF receiver that down-converts, acquires and tracks satellite signals, then computes position, velocity and time (PVT) solutions. Within the system hierarchy, it belongs to the GNSS receiver family, a subset of RF transceiver modules and location/navigation ICs. Modules like the SIM68M integrate the RF front end, baseband engine and navigation firmware into one SMT unit, saving designers months of RF development compared to chip-level designs. Key features include an MTK high-sensitivity navigation engine delivering industry-leading acquisition accuracy and Time-to-First-Fix (TTFF) at low power consumption. A built-in LNA removes the need for an external low-noise amplifier, and reception works down to -165 dBm without an assistance network. EASYTM self-generated orbit prediction (Embedded Assist System) combined with AlwaysLocateTM technology dramatically reduces TTFF in cold-start and periodic-wakeup scenarios. PPS output support enables precision time applications. Technically, SIM68M supports autonomous GPS/GLONASS/QZSS/SBAS (WAAS, EGNOS, MSAS, GAGAN) operation and simultaneous multi-constellation tracking of mixed satellite signals on the 1575-1616 MHz L1 bands. The SMT LCC package with castellated edges suits standard reflow assembly and automated optical inspection, and the antenna is connected through an RF pad on the module edge. Typical applications include vehicle and asset trackers, fleet management telematics, drone and UAV navigation, and IoT location beacons, where low power, fast TTFF and multi-constellation robustness in urban canyons matter most. Design consideration: supply the module from a clean 2.8 V to 4.3 V rail (typ. 3.3 V), keep a 1 ppm-class TCXO-equipped passive antenna within 1-2 m of the module, and reserve PCB area for the 18-pad footprint so the pin-compatible SIM68ML variant can be adopted later. This page synthesizes distributor pricing, verified specifications from the SIMCom specification and hardware design documents, and practical design notes not found in the manufacturer datasheet.
SIM7000A - LTE Cat-M/NB-IoT Module, GNSS | SIMCom
The SIMCom SIM7000A is an LTE Cat-M1 (eMTC) and NB-IoT LPWA cellular module with integrated multi-GNSS satellite navigation, delivered in a 24 x 24 mm LGA surface-mount package designed for North American IoT deployments. A cellular IoT module is a self-contained wireless communication subsystem that integrates a baseband processor, RF transceiver, power management, and memory into a single unit, sitting at the device level of the wireless connectivity hierarchy (module -> cellular modem -> M2M/IoT device -> IoT system). LPWA technologies such as Cat-M1 and NB-IoT trade bandwidth for dramatically lower power consumption and superior deep-indoor penetration compared with 2G/3G/4G broadband modems. Key features include dual-mode LTE Cat-M1/NB-IoT operation, multi-GNSS positioning (GPS/GLONASS/BeiDou/Galileo), and abundant interfaces including UART, GPIO, PCM, and I2C. The module is designed for applications requiring low-latency, medium-throughput data communication across varied radio propagation conditions, with ultra-low power consumption suited to battery- and solar-powered devices. A major engineering advantage is footprint compatibility: the SIM7000A LGA package is compatible with the legacy SIM900 and SIM800F modules, and its AT command set is mostly compatible with the SIM800F. This minimizes redesign investment and shortens time-to-market for designs migrating from 2G to LTE LPWA networks as carriers sunset legacy 2G infrastructure. Typical applications include asset tracking, smart metering, wearables, and remote telemetry in North American Cat-M1/NB-IoT networks, where the SIM7000A is a regional variant tuned for US carrier band support. Design consideration: supply the VBAT pins from a source capable of up to 2 A burst current with generous bulk capacitance to prevent voltage sag during RF transmit bursts. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
SIM7000E - LTE Cat-M/NB-IoT + GNSS Module | SIMCom | IoT
The SIMCom SIM7000E is a tri-band LTE-FDD cellular IoT module supporting LTE Cat-M1 (eMTC), NB-IoT (Cat-NB1), and dual-band GPRS/EDGE, with data rates up to 375 kbps and integrated GNSS positioning, housed in a compact 24x24 mm LGA surface-mount package. It operates from a 3.0V to 4.3V supply with a 9 uA low-power sleep current, making it ideal for battery-powered devices. A cellular LPWA (Low Power Wide Area) module is a type of wireless transceiver subsystem that connects embedded devices to carrier LTE networks optimized for low data rate, long battery life communication. Within the power/performance hierarchy, LPWA modules such as the SIM7000E sit below high-throughput 4G/5G modems (like the SIM7600 series) but above legacy 2G-only modems, offering a migration path as 2G networks are retired. Key features include LTE Cat-M1 and Cat-NB1 support for European-regional band plans (900 MHz and 1.8 GHz focus), EDGE/GPRS fallback for coverage holes, integrated GNSS for asset tracking, PCM voice capability, and rich interfaces: UART, USB 2.0, I2C, GPIO, and ADC. Architecturally, the SIM7000E integrates an LTE modem baseband, RF transceiver, power management, and GNSS receiver in a single module with an LGA land-grid-array footprint, reducing BOM cost versus discrete modem-plus-GPS designs. Deep-sleep power states at 9 uA enable multi-year operation on primary batteries in PSM/eDRX modes. Typical applications include smart utility meters, asset and fleet trackers, smart-city sensors, and alarm/security panels requiring low-latency medium-throughput cellular links. Design consideration: the power supply must deliver up to 2A during RF transmit bursts; SIMCom hardware design guidance recommends at least 300 uF (typically 1000 uF) of bulk capacitance on VBAT to keep voltage droop under 300 mV. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
SIM7000G - Cat-M/NB-IoT/GPRS/GNSS LPWA Module | SIMCom
The SIMCom SIM7000G is a multi-band LPWA cellular module supporting LTE Cat-M, NB-IoT, GPRS and EDGE on 850 MHz, 900 MHz, 1800 MHz and 1900 MHz bands, with an integrated GNSS receiver, housed in a 24 mm x 24 mm LCC surface-mount package supplied from 3.0 V to 4.3 V. An LPWA (Low Power Wide Area) module is a type of cellular transceiver optimized for low-latency, low-throughput machine-to-machine communication rather than bandwidth. Within the wireless hierarchy - transceiver, RF module, cellular modem, IoT connectivity layer - LPWA modules like the SIM7000G bridge battery-powered sensors to carrier networks over Cat-M (LTE-M), NB-IoT (Cat-NB), and the legacy 2G GPRS/EDGE fallback used where LTE coverage is unavailable. Key features include Power Save Mode (PSM) and extended Discontinuous Reception (eDRX) that enable battery life of up to 10 years, deep coverage enhancement relative to GSM, and abundant interfaces: UART, USB, GPIO, I2C, ADC, PCM, and SIM card. The integrated GNSS receiver provides positioning without a separate GPS module, reducing BOM cost and board area. Technically, the SIM7000 series is designed for varied radio propagation conditions, and the G variant is the global/regional-frequency version covering B1, B2, B3, B4 and additional bands per SIMCom documentation. The 24x24 mm LCC castellation footprint is pad-compatible with the SIM900/SIM800F footprint, and AT command sets are largely compatible with SIM800F, easing migration from 2G designs. Typical applications include smart metering, asset tracking, smart parking, smart city sensors, and industrial M2M telemetry - all scenarios where low data volume, deep indoor coverage, and multi-year battery life dominate. Design consideration: supply the module from a 3.3 V to 4.2 V source (Li-ion directly or a buck regulator) with low-ripple capability, since cellular TX bursts draw significant peak current; a single Li-ion cell within the 3.0 V to 4.3 V window is the standard approach. This page synthesizes distributor pricing, drop-in SIM7000-family alternatives, and practical design notes not consolidated in the manufacturer datasheet.
SIM7070G - Cat-M/NB-IoT/GSM GNSS IoT Module | SIMCom
The SIMCom SIM7070G is a multi-band cellular IoT transceiver module supporting LTE Cat-M (Cat-M1), NB-IoT (Cat-NB2) and GSM/GPRS with integrated GNSS (GPS/GLONASS/Galileo/BeiDou) satellite navigation, operating in the 850 MHz, 900 MHz, 1800 MHz and 1900 MHz bands and supplied as a surface-mount module without antenna. A cellular IoT module is a self-contained wireless transceiver that integrates a baseband processor, RF front end, power management and protocol stacks (TCP/IP, UDP, FTP, HTTP, MQTT) into a single LGA footprint. Within the system hierarchy, it sits above the antenna and below the host microcontroller, communicating via AT commands or USB to give any embedded system wide-area network connectivity without the designer handling RF certification directly. Key features include tri-mode fallback (Cat-M to NB-IoT to GSM) for global coverage, integrated GNSS receiver eliminating a separate GPS module, and Power Saving Mode (PSM) plus extended Discontinuous Reception (eDRX) that can extend battery life up to 10 years, according to SIMCom product documentation. Deep coverage enhancement versus legacy GSM improves link margin in basements and rural deployments. The SIM7070 series shares its form factor and AT command set with the SIM7000X/SIM800F/SIM900 families, enabling migration of legacy 2G designs to LPWA networks with minimal firmware changes. Data rates suit telemetry workloads rather than broadband: NB-IoT/Cat-M throughput is sufficient for MQTT messaging, fleet reporting and OTA configuration. The module runs the ThreadX RTOS per SIMCom user guides. Typical applications include asset tracking with GNSS positioning, smart utility metering, fleet telematics and battery-powered sensor nodes where multi-year battery life and carrier fallback between LTE-M, NB-IoT and 2G networks are required. Design consideration: the module is not pin-for-pin identical to the SIM800F; verify the hardware design guide (SIM7070G Hardware Design) for power supply sequencing, since peak transmit currents on GSM demand a low-ESR supply with adequate bulk capacitance. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
SIM7600CE-A - 4G LTE Cat-4 150Mbps Module | SIMCom
The SIMCom SIM7600CE-A is a 4G LTE Cat-4 wireless module delivering up to 150 Mbps downlink and 50 Mbps uplink, with multi-band TDD-LTE (B38/B39/B40/B41) support and integrated GNSS, housed in a 30 x 30 x 2.9 mm LCC (leadless chip carrier) surface-mount package. A cellular module of this type is a self-contained RF transceiver system that implements the modem baseband, RF front-end, and protocol stack of an LTE network terminal. Within the system hierarchy, it sits between the antenna connector and the host application processor, communicating over AT commands or USB, and forms the connectivity layer of the power management and communications subsystem of an IoT or M2M device. Key features include LTE Cat-4 peak throughput of 150 Mbps downlink / 50 Mbps uplink, backward compatibility with TD-SCDMA (384 Kbps downlink), HSPA+, EVDO, GSM/GPRS/EDGE, and integrated GNSS positioning (GPS + GLONASS + BeiDou). The compact 30 x 30 mm footprint makes it suitable for space-constrained industrial designs requiring both high-speed data and positioning. Technically, the SIM7600 series implements a multi-mode modem supporting LTE-TDD/FDD, TD-SCDMA, CDMA/EVDO, and GSM bands, allowing seamless fallback to 2G/3G networks where LTE coverage is unavailable. Data transfer over USB, UART, and optional audio interfaces enables straightforward integration with microcontrollers and Linux-based hosts via standard AT command sets and dial-up networking. Typical applications include industrial IoT gateways, vehicle tracking and telematics, smart metering backhaul, and security/camera systems that need reliable cellular data plus satellite positioning from a single module. Design consideration: LTE Cat-4 transmitters draw burst currents above 2 A at peak power; the host power supply must provide a stable 3.3-4.2 V rail with low impedance and adequate bulk capacitance to avoid voltage drops during transmit bursts and network registration. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
SIM7600G-H - LTE Cat-4 150Mbps Global 4G GNSS Module | SIMCom
The SIMCom SIM7600G-H is a global-band LTE Cat-4 cellular module delivering up to 150 Mbps downlink and 50 Mbps uplink in a 30 x 30 mm LCC surface-mount package, powered from a 3.4 V to 4.2 V supply with 2.3 mA idle current and integrated multi-constellation GNSS (GPS, BeiDou, GLONASS). A cellular module is a self-contained wireless modem that integrates baseband processor, RF transceiver, memory, and power management into a single land-grid-array unit. Within the wireless hierarchy it sits above discrete RF chipsets and below full gateways: host systems (MCU, SBC, or PC) talk to it over USB or UART using AT commands, while the module handles protocol stacks for LTE, WCDMA, and GSM internally. Key features include true global band coverage across LTE-FDD, LTE-TDD, WCDMA/HSPA+, EDGE, and GPRS, so a single PCB design ships to any region. The integrated GNSS receiver with simultaneous cellular-plus-GNSS operation serves trackers and telematics. Interfaces span USB 2.0, UART, I2C, SDMMC, ADC, and PCM voice with DTMF, audio playback, and recording. The module supports multiple built-in network protocols (TCP/IP, HTTP, FTP, MQTT-class stacks) and ships USB drivers for Windows, Linux, and Android, with a mainline Linux option in recent kernels. AT commands are compatible with the SIM7500/SIM7600 family, protecting software investment across variants. Typical applications include vehicle telematics and fleet trackers, industrial IoT gateways, and Raspberry Pi or LattePanda 4G connectivity via popular HAT boards. Critical design point: GSM burst emission draws up to 2 A ripple every 4.615 ms on the VBAT pins, so the supply must deliver more than 2 A with roughly 1000 uF bulk capacitance (or over 300 uF on a 2 A-capable rail) to keep voltage droop under 300 mV. This page adds value beyond the datasheet by synthesizing distributor pricing, drop-in family alternatives, and practical power-supply design guidance in one place.
SIM7670E - LTE Cat 1bis 10Mbps GNSS Module | SIMCom | IoT
The SIMCom SIM7670E is an LTE Cat 1bis wireless communication module based on the Qualcomm QCX216 chipset that supports LTE-FDD and LTE-TDD modes, delivering up to 10 Mbps downlink and 5 Mbps uplink data rates, with integrated GNSS positioning and a rich protocol stack including MQTT and HTTPS for IoT applications. An LTE Cat 1bis module is a category of cellular IoT modem that achieves LTE data rates using a single receive antenna, unlike Cat 1 with two receivers or Cat M1/NB1 low-power narrowband technologies. Within the wireless connectivity hierarchy, it sits above NB-IoT and Cat M modules in throughput while remaining far more cost-effective than Cat 4 modules, making it a key building block of power management and connectivity subsystems in cellular IoT devices. Key features include the 10 Mbps downlink / 5 Mbps uplink peak data rates enabled by the latest QCX216 chipset, support for both LTE-FDD and LTE-TDD wireless communication modes, integrated GNSS for satellite positioning, and built-in support for IoT application protocols such as MQTT and HTTPS, which reduces host-side firmware complexity. Architecturally, the QCX216 baseband integrates the LTE modem, application processor functions, and GNSS receiver in a single platform, simplifying the RF chain and bill of materials. The single-antenna Cat 1bis RF architecture halves receiver complexity compared with dual-receiver Cat 1, directly lowering module cost while preserving LTE latency and throughput benefits over 2G/3G alternatives. Typical applications include telematics and asset trackers that exploit the GNSS receiver plus LTE uplink, point-of-sale terminals and smart meters that rely on secure MQTT/HTTPS connectivity, and industrial gateways migrating from sunset 2G/3G networks (GSM/GPRS) to LTE, where the module provides a pin-compatible upgrade path from legacy SIM800/SIM7000 designs. A key design consideration is power: LTE Cat 1bis radios draw burst currents during transmission bursts, so the power supply must handle peak current demands with adequate bulk capacitance and a stable supply rail across the specified voltage range. This page synthesizes distributor data, drop-in alternative comparisons, and practical design notes not found in the manufacturer datasheet, with verified sources and freshness dating.
SIM7670G - LTE Cat-1 10Mbps GNSS Module | SIMCom
The SIMCom SIM7670G is an LTE Cat-1 wireless communication module with GNSS satellite navigation support, delivering up to 10 Mbps downlink and 5 Mbps uplink data rates in a 24 x 24 mm LCC+LGA form factor. It is built on the Qualcomm QCX216 chipset and supports LTE-FDD and LTE-TDD operation for global (G-region) deployments. An LTE Cat-1 module is a cellular IoT device category defined for machine-type communications that balances moderate data throughput with low cost and wide 4G LTE network coverage. Within the power-management hierarchy of connected devices, cellular modules such as the SIM7670G sit alongside NB-IoT (Cat-M/NB1) modules and full Cat-4 modems, occupying the sweet spot for devices that need several megabits per second, voice capability, and fallback-free LTE-only connectivity as 2G/3G networks sunset worldwide. Key features include Cat-1 peak rates of 10 Mbps DL and 5 Mbps UL, integrated GNSS receiver for positioning alongside cellular data, voice call support, and a supply voltage range of 3.4 V to 4.2 V. Typical quiescent/standby current figures of approximately 3 mA are cited by distributors for comparable SIMCom Cat-1 modules, and the module exposes a rich industrial interface set: UART, USB, I2C, SPI, GPIO, ADC, and SIM card interfaces. Technically, the SIM7670G uses the Qualcomm platform, which distinguishes it from the pin-similar SIMCom A7670X series based on the ASR platform; AT command compatibility across the SIMCom module ecosystem shortens software integration cycles. Embedded network protocol stacks and USB drivers for Windows, Linux, and Android reduce host-side development effort. Typical applications include cellular IoT gateways, vehicle trackers and telematics units, payment terminals, smart metering backhaul, and Raspberry Pi/ESP32-based HAT designs such as the Waveshare SIM7670G LTE Cat-1/GNSS HAT and LilyGo T-SIM7670G-S3. Design consideration: because the module requires a tightly regulated 3.4-4.2 V supply with adequate burst-current headroom during RF transmission, budget the power rail carefully and follow the manufacturer hardware design guide for antenna and keep-out layout. This page synthesizes distributor pricing, regional variant comparisons, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet alone.
SIM7672E - LTE Cat 1bis 10Mbps Module | SIMCom | IoT M2M
The SIMCom SIM7672E is an LTE Cat 1bis cellular module based on the Qualcomm QCX216 chipset that supports LTE-FDD and LTE-TDD wireless communication modes with a maximum downlink rate of 10Mbps and a maximum uplink rate of 5Mbps, housed in an LCC+LGA form factor package. The E regional variant targets the EMEA (Europe, Middle East, Africa) market with LTE band coverage for those regions. An LTE Cat 1bis module is a category of cellular IoT modem that uses a single antenna (bis = one receive antenna) to deliver Category 1 data rates, positioning it in the hierarchy of cellular connectivity as: Cat 1bis -> LTE Cat 1 -> LTE (4G) -> cellular wide-area network -> wireless communication module. It is widely adopted as the successor technology to 2G (GSM/GPRS) and NB-IoT/Cat M modules for machine-to-machine (M2M) and Internet of Things (IoT) devices that require moderate throughput at low power and low cost. Key differentiating features include the 10Mbps downlink / 5Mbps uplink throughput envelope, the modern QCX216 platform that ensures long-term LTE network longevity, and the LCC+LGA form factor that is pin-compatible by design with SIMCom's A7672 series (Cat 1), SIM7000/SIM7070 series (NB-IoT/Cat M), and SIM800/SIM800F series (2G) modules. This enables a smooth hardware migration path from legacy 2G or NB-IoT products to LTE Cat 1 without a PCB redesign. Technically, the module integrates the cellular baseband, transceiver, RF front end, power management, and a USB 2.0 interface plus UART for host communication, with standard AT command control documented in the SIM76XX Series AT Command Manual. Firmware is updated over USB, and typical host integration uses a microcontroller or application processor driving the UART interface. Typical applications include smart metering, asset trackers and fleet telematics, POS terminals, industrial gateways, security alarm panels, and shared-economy devices such as bike sharing and EV charging stations - use cases that need reliable mid-rate cellular data with multi-year network support. For design-in, pay close attention to power supply design: cellular PA transmit bursts draw high peak currents, so use a low-ESR bulk capacitor near the VBAT pins and follow the reference layout for the antenna feed and grounding to preserve RF performance. This page synthesizes verified datasheet parameters, distributor pricing context, drop-in alternatives within the SIMCom footprint family, and practical design notes not found together in the manufacturer datasheet. Pricing references are as of 2026-10-20.
SIM7672G-MNGV - LTE Cat 1bis 10Mbps Module GNSS | SIMCom
The SIMCom SIM7672G-MNGV is an LTE Cat 1bis cellular module with integrated GNSS receiver delivering up to 10 Mbps downlink and 5 Mbps uplink data rates in a compact 24 x 24 x 2.4 mm LCC+LGA surface-mount package. An LTE Cat 1bis module is a category of cellular IoT modem that uses a single receive antenna (bis = one RX chain) to achieve LTE FDD/TDD connectivity at lower cost and power than multi-antenna Cat 4 modules. Cat 1bis sits within the wider LTE category hierarchy of cellular modules, bridging the gap between legacy 2G/GPRS modules such as the SIM800 series and higher-throughput LTE routers, making it the de facto migration path for global 2G/3G sunset designs. Key features include operation on the latest Qualcomm QCX216 chipset, support for LTE-FDD and LTE-TDD wireless modes, worldwide band coverage for global roaming, and form-factor compatibility with the SIMCom A7672 series (Cat 1), SIM7000/SIM7070 series (NB-IoT/Cat M) and SIM800/SIM800F series (2G). This compatibility allows designers to drop the module onto an existing A7672-class land pattern and migrate from 2G, NB-IoT or Cat M products to LTE Cat 1 with minimal PCB rework. Technically, the QCX216 platform integrates the cellular baseband, transceiver and memory in a single chipset, and the G variant adds GNSS (GPS/BeiDou-class satellite positioning) for asset tracking and telematics. Software functions include FOTA (firmware over the air), SSL secure transport, and VoLTE voice support, with AT-command control per the SIM76XX Series AT Command Manual. Typical applications include global-roaming asset trackers, automotive telematics, smart metering, payment terminals, and industrial IoT gateways where LTE longevity matters more than raw throughput. Design consideration: because Cat 1bis uses a single RX chain, throughput falls back gracefully rather than relying on RX diversity - ensure antenna matching and power-supply design follow the SIM7672 hardware design guide for peak-current bursts during LTE transmission. This page synthesizes distributor availability, drop-in family alternatives, design notes, and commercial data not consolidated in the manufacturer datasheet.
SIM800C - Quad-Band GSM/GPRS Module | SIMCom
The SIM800C is a complete Quad-Band GSM/GPRS module in a compact LCC (Leadless Chip Carrier) package, designed by SIMCom Wireless Solutions. It operates on 850/900/1800/1900 MHz frequencies and supports GPRS data transfer up to 85.6 kbps. The module measures 17.6 x 15.7 x 2.3 mm, making it suitable for space-constrained IoT and embedded applications. It requires a supply voltage of 3.4V to 4.4V and features a 42-pin SMD interface. A GSM/GPRS module is a cellular communication module that enables devices to connect to GSM networks for voice, SMS, and data services. It integrates a baseband processor, RF transceiver, and power management into a single package, allowing developers to add cellular connectivity to their products without designing complex RF circuitry. The SIM800C sits within the hierarchy of cellular modules, which includes 2G, 3G, 4G LTE, and NB-IoT categories, and is specifically a 2G GSM/GPRS module. Key features of the SIM800C include support for Quad-Band frequencies, GPRS multi-slot class 12, and a rich set of interfaces including UART, USB 2.0, GPIO, SPI, and I2C. It also integrates an audio codec with speaker and microphone amplifiers, making it ideal for voice applications. The module supports AT command control, enabling easy integration with microcontrollers. Its low power consumption in sleep mode (around 1 mA) is beneficial for battery-powered devices. Technically, the SIM800C is built on a mature GSM/GPRS platform, offering reliable performance in 2G networks. It supports SMS, voice calls, and data transmission, with a maximum GPRS downlink speed of 85.6 kbps. The module includes a power management unit that handles over-voltage and under-voltage protection, ensuring safe operation. It also features a PWRKEY pin for power-on/off control and supports normal power-off via AT command 'AT+CPOWD=1'. Typical applications include remote monitoring, asset tracking, alarm systems, smart metering, and IoT gateways. Its compact size and low power consumption make it suitable for portable devices, while its robust interface set allows for flexible system integration. The SIM800C is widely used in industrial and consumer applications where 2G connectivity is still available. When designing with the SIM800C, ensure a stable power supply within 3.4V to 4.4V and adequate decoupling. The module requires a proper antenna connection and careful PCB layout to minimize RF interference. Also, consider the lifecycle status, as 2G networks are being phased out in many regions, which may affect long-term deployment.
SIM800C - Quad-Band GSM/GPRS Module | SIMCom | IoT & M2M
The SIM800C is a complete Quad-Band GSM/GPRS module in a compact LCC (Leadless Chip Carrier) package, designed by SIMCom Wireless Solutions. It operates on 850/900/1800/1900 MHz frequencies and supports GPRS data transfer up to 85.6 kbps. The module measures only 17.6 x 15.7 x 2.3 mm, making it ideal for space-constrained IoT and M2M applications. It provides a rich set of interfaces including UART, USB 2.0, GPIO, and an audio codec with speaker and microphone amplifiers, enabling voice, SMS, and data communication. A GSM/GPRS module is a self-contained cellular communication device that integrates a baseband processor, RF transceiver, and power management into a single package. It connects to a microcontroller via serial interfaces (typically UART) and communicates using AT commands. The SIM800C sits within the hierarchy: GSM/GPRS module -> cellular module -> wireless communication module -> IoT connectivity component. This modular approach simplifies adding cellular connectivity to embedded systems without requiring deep RF design expertise. Key features of the SIM800C include support for Quad-Band GSM/GPRS (850/900/1800/1900 MHz), GPRS class 12 (up to 85.6 kbps), and a wide operating voltage range of 3.4V to 4.4V. It integrates an audio codec and amplifiers for voice applications, and offers low power consumption in sleep mode (around 1 mA), which is critical for battery-powered IoT devices. The module also supports a variety of network protocols including TCP/IP, UDP, HTTP, and FTP via AT commands, enabling direct internet connectivity. Technically, the SIM800C uses a LCC package with 42 pins, providing excellent thermal and electrical performance. It includes a power management unit that handles over-voltage and under-voltage protection, and supports both normal and abnormal power-off procedures via the PWRKEY pin or AT command AT+CPOWD=1. The module is designed for easy integration with a minimal external component count, requiring only a power supply, SIM card holder, antenna, and a few passive components. Typical applications include remote monitoring and control systems, vehicle tracking devices, smart meters, alarm systems, and portable IoT devices. Its compact size and low power consumption make it suitable for battery-operated devices that need periodic data transmission. The SIM800C is also widely used in development boards and prototyping platforms. When designing with the SIM800C, ensure a stable power supply capable of handling current peaks up to 2A during GSM transmission bursts. Proper PCB layout with adequate grounding and decoupling is essential to maintain RF performance and minimize noise. Also, consider the module's lifecycle status, as it is being phased out in favor of 4G/LTE modules; for new designs, evaluate alternatives like the SIMCom A7683E or SIM7080G.
SIM868 - Quad-Band GSM/GPRS + GNSS Module | SIMCom
The SIMCom SIM868 is a quad-band GSM/GPRS cellular module with integrated GNSS satellite navigation (GPS/GLONASS/BDS), operating from a 3.4V to 4.4V supply with 650 uA idle current, housed in a compact 17.6 x 15.7 mm LCC/LGA surface-mount package. A GSM/GPRS module is a wireless communication subsystem that provides cellular voice, SMS, and packet-switched data connectivity over 2G mobile networks. Within the system hierarchy, it sits between the antenna/RF front end and the host microcontroller, abstracting the cellular protocol stack behind AT commands over UART. Modules such as the SIM868 belong to the broader family of cellular IoT modules, which also includes 3G, 4G/LTE, and LPWA (Cat-M/NB-IoT) devices. Key features include worldwide quad-band operation at 850/900/1800/1900 MHz, GPRS multi-slot class data rates up to 85.6 kbps in both downlink and uplink, and a co-located GNSS receiver supporting GPS, GLONASS, and BeiDou (BDS) constellations for positioning without a second module. The SIM868 integrates abundant extension interfaces: UART, USB 2.0, I2C, GPIO, dual SIM card interfaces, and an SD card interface. The dual-SIM capability is a differentiator versus the earlier SIM808, enabling multi-carrier failover designs. The compact LCC and LGA pad design significantly reduces development time and cost for GNSS-enabled M2M applications, and the module is ROHS compliant. Typical applications include asset tracking, vehicle fleet monitoring, anti-theft systems, and general M2M IoT devices that need both cellular telemetry and satellite positioning in a single footprint. Design considerations: supply the module from a low-impedance 3.4V to 4.4V rail capable of handling GSM transmit burst currents, and verify antenna keep-out areas in the 17.6 x 15.7 mm footprint region. This page synthesizes distributor pricing, availability, drop-in alternative analysis, and design notes not found in the manufacturer datasheet. According to the SIMCom product page, the SIM868 combines a complete quad-band GSM/GPRS engine with GNSS technology for satellite navigation.
SKY13522-644LF - 0.7-6 GHz SPDT RF Switch, 8-QFN | Skyworks
The Skyworks SKY13522-644LF is a single-pole, double-throw (SPDT) reflective RF switch covering 0.7 GHz to 6.0 GHz with 50 Ohm matching, housed in an 8-pin QFN (1.1 x 1.1 mm) surface-mount package. It delivers low insertion loss and high isolation suitable for cellular transmit/receive path routing, with single-bit GPIO control and 3 GHz maximum operating frequency in cellular band applications. An RF SPDT (single-pole double-throw) switch is a semiconductor routing element that selects one of two RF signal paths using a control voltage. SPDT switches belong to the broader category of RF switches -> RF front-end components -> wireless transceivers -> RF & wireless ICs. They are essential building blocks in time-division duplex (TDD) systems, antenna diversity modules, and band-selection filters, where a single antenna or filter bank must be shared between transmit and receive or between multiple bands. Key features include 0.7 GHz to 6.0 GHz operating range, 50 Ohm characteristic impedance, single-bit (one logic input) control interface, integrated DC blocking on the RF ports, and a compact 1.1 x 1.1 mm QFN-8 footprint. The advanced pHEMT switching technology maintains low insertion loss and high isolation across all switching paths, making the part well suited to cellular handset and module designs targeting GSM, CDMA, WCDMA, and LTE front-end sections. The device operates from a single supply and draws minimal DC current; the switch state is set by a single CMOS-compatible logic input, simplifying host-MCU or baseband GPIO integration. Internal ESD protection on the RF pins and the control input increases robustness during module assembly and field use. Typical applications include cellular handset transmit/receive switching, Wi-Fi 2.4 GHz and 5 GHz band routing, Bluetooth/BLE front-end switching, IoT and wearables antenna diversity, GPS L1 path selection, and reference designs for Wi-Fi + BLE combo modules. The broadband response also extends to 5 GHz Wi-Fi and sub-6 GHz industrial/scientific/medical bands. When designing with this part, place RF traces as 50 Ohm controlled-impedance lines and keep the VC1 control line routed away from sensitive RF traces to avoid digital-to-RF coupling. Decouple VDD close to the pin with a 1 nF to 100 pF combination; a typical application uses a single 1 nF X7R capacitor. This page synthesizes distributor pricing, EOL replacement guidance, drop-in alternatives, and practical design notes that complement the Skyworks manufacturer datasheet.
SKY13522-644LF-EVB - 0.7-3GHz SPDT Switch Evaluation Board | Skyworks
The Skyworks SKY13522-644LF-EVB is an evaluation board for the SKY13522-644LF single-pole, double-throw (SPDT) RF switch IC, covering the 0.7 GHz to 3 GHz frequency band with 50 ohm single-ended RF ports in a compact 8-QFN (1.1x1.1 mm) package. The host IC targets cellular front-end switching in CDMA, GSM, and WCDMA air interfaces and delivers high isolation of approximately 47 dB at 2.2 GHz, with low insertion loss supporting transmit/receive and band-switch routing. An RF switch (SPDT) is a semiconductor device that routes a single RF input to one of two RF output paths under logic-level CMOS control, enabling transmit/receive duplexing, antenna band selection, or diversity switching in a wireless front-end module. As part of the broader RF front-end (RFFE) hierarchy, the SPDT sits between the antenna or filter bank and the transceiver chain, and is typically controlled directly by the transceiver's GPIO or RFFE bus. Compared to mechanical relays, solid-state GaAs pHEMT-based SPDTs switch in tens of nanoseconds, draw only a few microamperes of quiescent current, and integrate into the same reflow-soldered PCB as the surrounding ICs. Key electrical characteristics of the underlying SKY13522-644LF device include a single-bit CMOS control interface that minimizes GPIO overhead, low insertion loss typically in the 0.4-0.6 dB range at 1-2 GHz, and high port-to-port isolation near 47 dB at 2.2 GHz, enabling signal chains to maintain dynamic range. The 50 ohm matched ports eliminate external matching networks and simplify board-level integration. The silicon implementation uses Skyworks' GaAs pHEMT switching process, which provides the linearity required for cellular power levels up to roughly +30 dBm, low DC power consumption with a few microamperes of quiescent current, and a single positive supply between approximately 2.5 V and 5.0 V. The 8-pin QFN (1.1 x 1.1 mm) exposed-pad package offers a low-inductance ground reference and excellent thermal performance for the small die area. The evaluation board hosts the IC on a calibrated FR4 substrate with SMA connectors and controlled-impedance traces so engineers can directly probe RF performance and control logic using standard laboratory instruments. Typical use cases for the SKY13522-644LF and its evaluation board include cellular handset transmit/receive switching, Wi-Fi/Bluetooth module antenna multiplexing, front-end module development for IoT and wearables, and reference designs for sub-6 GHz cellular and short-range radio platforms. The 0.7-3 GHz range matches cellular low-band, mid-band, 2.4 GHz ISM, and 2.6 GHz LTE/Wi-Fi bands. When designing with this part, drive the CMOS control pin from a clean logic rail (typically 1.8 V or 3.3 V) and place the control trace away from RF paths to avoid coupling. The exposed paddle of the QFN must be soldered to a continuous ground plane with multiple thermal vias for stable RF ground reference. This page synthesizes distributor availability, Skyworks' suggested replacement guidance, and EVB-related design notes that complement but do not replace the underlying SKY13522-644LF datasheet.
SKY66122-11 - 863-928MHz Wi-SUN RF Front End | Skyworks
The Skyworks Solutions SKY66122-11 is a high-performance, highly integrated RF front-end module (FEM) integrating a power amplifier (PA) and low-noise amplifier (LNA) for high-power 863 MHz to 928 MHz ISM band, Wi-SUN, and other IoT applications, housed in a 36-pin multi-chip module (MCM) package measuring 6x6 mm. An RF front-end module is a subsystem sitting between the radio transceiver IC and the antenna in a wireless signal chain. It typically combines a transmit-path power amplifier, a receive-path low-noise amplifier, RF switches for TX/RX switching, and a power detector for closed-loop output power control, all matched to 50 ohms so the system designer does not need external RF matching components. FEMs belong to the broader hierarchy of RF ICs, which includes transceivers, amplifiers, switches, and filters within the radio-frequency semiconductor family. Key features of the SKY66122-11 include fully matched 50 ohm RF input and output that eliminate external matching networks, digital control interfaces compatible with 1.6 V to 3.6 V CMOS logic levels for direct connection to common sub-GHz transceivers, an integrated RF switch for TX/RX path selection, and an integrated power detector that enables output power monitoring and closed-loop control. LCSC-listed features also cite an ultra-low 0.05 uA shutdown current, critical for battery-powered Wi-SUN and mesh nodes that sleep for most of their duty cycle. The integration of PA, LNA, switch, and coupler/detector in a single 6x6 mm MCM dramatically reduces board area compared with a discrete chain, and the internal inter-stage matching and harmonic filtering simplify compliance design for regional sub-GHz regulations in the 863-928 MHz band. The module is designed for ease of use and maximum flexibility, per the Skyworks product page. Typical applications include Wi-SUN mesh network routers and border routers, high-power ISM band telemetry, long-range Meshtastic and LoRa-style nodes (the part is used with the Semtech SX1262 in WisMesh high-power booster designs), smart metering, and street lighting control networks. Design consideration: as a high-power PA module, the SKY66122-11 requires attention to thermal pad grounding and supply decoupling; consult the manufacturer datasheet for the recommended PCB land pattern and thermal via array. This page synthesizes distributor pricing, availability, application context, and practical design notes not found in a single manufacturer datasheet.
SKY66122-11EK1 - 863-928MHz Wi-SUN FEM Eval Board | Skyworks
The Skyworks Solutions SKY66122-11EK1 is the official evaluation board for the SKY66122-11 high-performance RF front-end module (FEM), tuned for 863 to 915 MHz operation and intended for rapid prototyping of Wi-SUN, ISM-band, and IoT radio designs. An RF front-end module (FEM) evaluation board is a reference PCB that mounts the target RFIC together with the recommended matching network, decoupling, RF connectors, and control interfaces, allowing engineers to measure transmit power, receive sensitivity, and current consumption before committing to a custom layout. In the RF signal-chain hierarchy (evaluation board -> front-end module -> RF transceiver -> wireless node), the SKY66122-11EK1 sits at the top as a measurement and validation vehicle. The underlying SKY66122-11 FEM integrates a power amplifier, a low-noise amplifier (LNA), an RF switch, and a power detector in a single 36-pin MCM (6x6 mm) package. It provides fully matched 50 ohm RF input and output, digital control lines compatible with 1.6 V to 3 V logic, and supports the 863 to 928 MHz high-power ISM band for OFDM modulations such as Wi-SUN. Typical uses include bench characterization of output power and harmonic performance, link-budget validation for sub-GHz mesh networks, firmware development for radio controllers driving the digital control pins, and regulatory pre-scanning in the 863-928 MHz band. When using the board, maintain a clean low-noise supply and calibrate measurements with a calibrated vector signal analyzer to preserve result accuracy. This page synthesizes distributor pricing, datasheet references, and practical evaluation guidance not found in a single manufacturer page.
SKY66315-11 - 4.4-5GHz 5V RF Power Amp | Skyworks
The Skyworks SKY66315-11 is a high-efficiency, wide instantaneous bandwidth RF power amplifier (driver amp) designed for 4G LTE and 5G FDD/TDD systems operating from 4.4 GHz to 5 GHz, delivering approximately 35 dB of gain in a compact 16-MCM (5 x 5 mm) surface-mount package. An RF power amplifier is a power management stage in the radio-frequency transmit chain that boosts a modulated carrier to the drive level required by the antenna or final-stage PA. Within the signal-chain hierarchy, the power amplifier sits after the upconverter/transceiver and before the front-end module, making its gain, linearity, and efficiency decisive for overall radio range and spectral compliance. Key features include full input/output matching (no external matching networks required in typical designs), integrated active biasing circuitry that compensates performance over temperature, supply voltage, and process variation, and high gain with good linearity for wide-bandwidth OFDM waveforms. The device operates from a supply voltage between 4 V and 5.25 V with typical current consumption of approximately 115 mA, supporting standard 5 V RF system rails. Architecturally, the SKY66315-11 is a fully matched multi-chip module (MCM) amplifier; the 5 x 5 mm footprint and internal impedance matching reduce board area and simplify design-in for n79-band and related 5 GHz sub-6 GHz radios. The active bias scheme keeps quiescent current stable across the -40 C to +85 C (per datasheet) range, improving gain flatness over conditions compared with fixed-bias solutions. Typical applications include 5G NR sub-6 GHz small-cell and macro-cell driver stages, 4G LTE TDD/FDD transmit chains, customer-premises equipment (CPE) and fixed wireless access radios, and test/measurement signal sources in the 4.4-5 GHz band. For design-in, verify supply decoupling with low-ESR ceramics close to the supply pins and provide an adequate ground via array under the package thermal path to manage power dissipation; also confirm ACPR/linearity under the specific waveform and back-off of the target standard. This page synthesizes distributor availability, cross-family alternatives, design guidance, and application context not found in a single manufacturer datasheet.
SKY66394-11 - 2000-2300 MHz High-Efficiency PA | Skyworks
The Skyworks SKY66394-11 is a high-efficiency fully input/output matched power amplifier (PA) with high gain and linearity, operating across 2000 MHz to 2300 MHz with up to 4W (36 dBm) output power, integrated in a compact 16-MCM 5 x 5 mm package. An RF power amplifier (PA) is the final active stage in a wireless transmitter chain that boosts a low-level modulated signal to a transmit power level suitable for radiation by an antenna. PAs sit between the transceiver/transmitter IC and the front-end filter/antenna switch, within the broader category of RF & wireless front-end modules. For small-cell base stations, PAs must simultaneously deliver high linearity (low ACLR/EVM) for LTE/3GPP compliance and high efficiency to minimize power dissipation and thermal load in space-constrained, often outdoor or pole-mounted enclosures. The SKY66394-11 is engineered specifically for FDD and TDD 2G/3G/4G LTE small-cell infrastructure. Key features include a wide instantaneous bandwidth of 300 MHz (2000 to 2300 MHz), high gain of approximately 36 dB, integrated active bias circuitry that compensates PA performance over temperature, voltage, and process variation, and full 50-ohm input/output matching that eliminates external matching components. The 5 x 5 mm MCM package integrates the active die, bias network, and matching networks to simplify PCB design and reduce board area in small-cell radio units. The SKY66394-11 belongs to a pin-to-pin compatible PA family from Skyworks, with sibling parts covering other 3GPP bands. This enables a single PCB layout to be reused across multiple regional band variants, simplifying manufacturing and inventory. The integrated active biasing stabilizes quiescent current across temperature and supply variation, eliminating the need for external bias controllers. Typical applications include 4G LTE small-cell base stations, picocell and femtocell radios, distributed antenna systems (DAS) repeaters, and Band 1 / Band 3 / Band 4 / n38 / n40 / n41 (subset) FDD and TDD cellular infrastructure. It is also suitable for industrial 2.3 GHz wireless backhaul links. When designing with this part, provide adequate heatsinking through PCB copper pours to manage thermal dissipation at high output power. Use a regulated 5V supply for VCC and follow the reference layout in the datasheet closely to preserve the integrated matching network performance. Reference impedance is 50 ohms on both RF ports. This page synthesizes distributor pricing, pin-compatible same-family alternatives (such as SKY66395-11 and SKY66396-11), and practical RF layout guidance not found in the manufacturer datasheet alone, giving the engineer a single decision-ready reference for 2.0-2.3 GHz small-cell PA selection.
SKY66409-11 - 2.4 GHz FEM for Zigbee/Thread/BLE | Skyworks
The Skyworks SKY66409-11 is a high-performance, fully integrated 2.4 GHz RF front-end module (FEM) designed for Zigbee, Thread, and Bluetooth (including Bluetooth Low Energy) applications, housed in a compact 12-ball WLCSP package (1.25 x 1.7 mm). It integrates a power amplifier (PA), low-noise amplifier (LNA), low-loss bypass path, transmit/receive switches, and digital control logic, providing a complete RF front-end solution in a single die. The digital controls are compatible with 1.2 V to 3.6 V logic, allowing direct interfacing with low-power microcontrollers and SoCs. A front-end module (FEM) is a critical subsystem in any wireless transceiver design, sitting between the transceiver IC and the antenna. It amplifies the transmit signal (PA), boosts receive sensitivity (LNA), routes the RF path between TX and RX modes (switches), and optionally bypasses the LNA for power savings. The FEM category sits hierarchically under RF ICs -> wireless transceivers -> RF subsystems, and the SKY66409-11 targets low-power IoT and wearable applications where size, efficiency, and bill-of-material count are critical. Key specifications include integrated TX/RX switching, optimized for +20 dBm output power in Zigbee/Thread modes and Bluetooth/BLE soaks through the PA chain, plus an integrated bypass path that improves RX power consumption when high LNA gain is not required. The 12-ball WLCSP footprint (1.25 x 1.7 mm) makes the part suitable for space-constrained wearables, beacons, and sensor nodes where every square millimeter counts on the PCB. The SKY66409-11 architecture pairs a GaAs/AlGaAs HBT PA with a silicon-on-insulator (SOI) switch/LNA core, providing high efficiency in TX and low noise figure in RX. Digital control inputs (CSD, CTX, CRX, CPSDO, CRSB) eliminate external RF switch driver complexity and enable direct host-microcontroller control. The module is designed for ease of use with minimal external matching, reducing total design cycle time for high-volume IoT products. Typical applications include Zigbee/Thread smart-home hubs and end devices, Bluetooth Low Energy wearables and fitness bands, asset tracking beacons, and Matter-compatible wireless sensor nodes. The wide supply range and low standby current also make it a strong fit for battery-powered devices targeting multi-year coin-cell lifetimes. When designing with the SKY66409-11, follow the Skyworks reference layout to control RF coupling between the PA output and the LNA input. Place the DC control pull-up/down resistors close to the chip balls and use a solid ground plane on layer 2 beneath the WLCSP. Decoupling capacitors must be placed within 1 mm of the supply balls to maintain stable operation across the 1.6 V to 3.6 V supply range. This page synthesizes distributor pricing, datasheet specifications, drop-in alternatives within the same WLCSP footprint, and practical design notes not found in a single source on the manufacturer datasheet.
SR1010AB-MD150-MP1 - UWB Transceiver Module 3.1-5.8GHz | SPARK Microsystems
The SPARK Microsystems SR1010AB-MD150-MP1 is an 802.15.4 Ultra Wideband (UWB) impulse radio transceiver module operating across the 3.1 GHz to 5.8 GHz frequency band, with an integrated trace antenna and a connector mount form factor for flexible host-board integration. An ultra wideband transceiver module is a complete radio subsystem that transmits data using extremely short, low-power pulses spread across a very wide spectrum. In the RF hierarchy, a UWB module sits within the broader categories of RF transceivers, short-range wireless communication systems, and RF modules. UWB technology enables precise ranging and high data-rate links with very low energy per bit, which is why it has become the preferred physical layer for indoor positioning, secure keyless entry, and low-power wireless sensor networks. Key features of this module include IEEE 802.15.4 UWB impulse radio compliance, coverage of the full 3.1 GHz to 5.8 GHz UWB band, and an integrated trace antenna that eliminates the need for external antenna design and RF matching work. According to the SPARK Microsystems product highlight on DigiKey, the SR1010AB-MD150-MP1 and its sibling SR1020AB-MD110-MP1 are characterized by ultra-low power consumption, which directly extends battery life in portable and IoT devices. The SPARK Microsystems SR1010 transceiver family is built around SPARK's proprietary impulse radio architecture, which achieves efficient wake-and-transmit cycles rather than continuous carrier operation. This makes the module particularly suited to applications where average current draw, not peak throughput, dominates the power budget. The integrated antenna design also shortens time-to-market because the RF section is pre-certified and pre-matched at the module level. Typical applications include asset tracking and indoor positioning systems, wireless sensor networks for industrial monitoring, and low-latency gaming or wearable links where milliwatt-scale average power matters. The connector mount form factor allows prototyping and production integration without soldering the module directly onto the main PCB. Designers should account for antenna keep-out and ground clearance around the module's integrated trace antenna, and verify regulatory channel selection within the 3.1 GHz to 5.8 GHz band for the target region. This page synthesizes distributor pricing, family alternatives, and practical design notes not found in the manufacturer datasheet, with prices verified as of 2026-10-20.
SR1020AB-MD110-MP1 - UWB Transceiver Module 6-9.3GHz | SPARK Microsystems
The SPARK Microsystems SR1020AB-MD110-MP1 is an IEEE 802.15.4 Ultra Wideband (UWB) impulse radio RF transceiver module covering the 6 GHz to 9.3 GHz band, with an integrated antenna arrangement and trace connector mounting for flexible integration into host PCBs. It delivers up to 6 Mbps data throughput with an ultra-low-power duty-cycled architecture optimized for battery-powered wireless connectivity. Ultra Wideband impulse radio is a wireless communication technology that transmits data using nanosecond-scale pulses spread over several gigahertz of spectrum, rather than a narrowband modulated carrier. Within the radio hierarchy, the SR1020 sits as a physical-layer transceiver solution under short-range wireless standards (802.15.4 UWB), competing in the same application space as BLE, 802.15.4 Zigbee, and LoRa radios, but offering far lower energy per bit and very low latency. Key differentiating specifications include deep sleep current of just 920 nA and shutdown current of 55 nA, enabling multi-year coin-cell operation under defined use conditions and even energy-harvesting configurations. The active power profile is exceptionally efficient for the 6-9 GHz band: 0.39 mA/Mbps in receive and 0.12 mA/Mbps in transmit at 3.3 V, which is an order of magnitude better energy-per-bit than typical narrowband radios at comparable throughput. The SR1020 architecture aggressively duty-cycles the radio, waking only for short UWB bursts. This yields microsecond-scale synchronization and low-latency links suited to wireless gaming peripherals, true wireless audio, and industrial sensor networks. Data rates from low-kbps telemetry up to 6 Mbps allow a single radio platform to serve both monitoring and streaming use cases. Typical applications include wireless gaming headsets and mice, true wireless earbuds with ultra-low latency, coin-cell IoT sensors, and energy-harvesting industrial nodes where battery replacement is impractical. Design consideration: because UWB performance depends on antenna integration and host-board grounding, follow the SPARK Microsystems reference layout and use the trace connector footprint exactly as specified in the manufacturer datasheet to preserve RF performance and regulatory compliance. This page synthesizes distributor pricing, family alternatives, and practical design guidance not found in the manufacturer datasheet, with pricing data as of 2026-10-20.