10M08DCU324A7G - MAX 10 FPGA, 8K LE, 324-LFBGA | Intel
부품 번호: 10M08DCU324A7G ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $38.5 | $38.50 |
| 10 | $35.2 | $352.00 |
| 100 | $31.8 | $3,180.00 |
| 500 | $28.4 | $14,200.00 |
| 1,000 | $25.1 | $25,100.00 |
10M08DCU324A7G 개요
What is an FPGA? A Field-Programmable Gate Array (FPGA) is a semiconductor IC whose digital logic fabric can be reconfigured by the designer after manufacturing, in contrast to an ASIC whose function is fixed at tape-out. FPGAs sit within the broader taxonomy of programmable logic devices (PLDs) -> programmable logic -> logic ICs -> integrated circuits -> semiconductors. MAX 10 devices are non-volatile FPGAs with on-die flash configuration memory, distinguishing them from SRAM-based competitors that require external boot flash.
Key features include integrated 12-bit ADC blocks, on-chip flash for instant-on configuration, dual-configuration flash support, and DSP blocks in selected variants. The U324 package exposes up to 246 user I/O with mixed-voltage support (1.2 V, 1.5 V, 1.8 V, 2.5 V, 3.3 V) on user I/O banks. The device integrates phase-locked loops (PLLs) for clock management and includes embedded SRAM blocks distributed across the fabric.
The MAX 10 architecture employs logic-array blocks (LABs) each containing 16 logic elements, interconnected by a multi-level routing hierarchy with embedded multiplier blocks and RAM blocks. The non-volatile configuration memory enables single-chip FPGA operation without external boot PROMs, simplifying board design and reducing BOM cost.
Typical applications include industrial motor control, automotive body electronics, sensor aggregation, display controllers, low-cost video processing, and I/O expansion bridges. The AEC-Q100 qualification makes the device particularly suitable for under-hood and body-control applications where temperature extremes are routine.
When designing with the 10M08DCU324A7G, ensure that the chosen variant matches the I/O bank voltage mix required by your design. The internal configuration time after power-on is typically sub-100 ms because configuration is read from on-chip flash rather than an external serial PROM, which simplifies power-sequencing requirements.
This page synthesizes distributor pricing, drop-in alternative MAX 10 same-family variants, and practical design notes not collected in a single section of the manufacturer datasheet.
드롭인 대체품: 10M08DCU324A7G — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: 10M08DCU324A7G (동일 폼 팩터 및 풋프린트) — 차이점: Package, Process Technology, Logic Elements (LE), Mounting Type, Family.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
10M08DCU324C8G
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
10M08DCU324I7G
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$8.5 / 개
데이터시트 보기 →10M08DCU324I7P
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
10M04DCU324A7G
✅ 드롭인✓ 재고 있음
$9.85 / 개
데이터시트 보기 →10M04DCU324C8G
✅ 드롭인✓ 재고 있음
$13.8 / 개
데이터시트 보기 →10M08DCU324A7G 최대 정격 & 전기적 특성
| Family | MAX 10 |
| Logic Elements (LE) | 8,000 |
| Embedded Memory (Kbits) | 246 |
| User Flash Memory (bits) | 387,072 |
| Total User I/O | 246 |
| 패키지 | 324-LFBGA (U324) |
| Process Technology | 55 nm |
| Core Supply Voltage | 1.15 V to 1.25 V |
| Maximum Internal Clock Frequency | 382 MHz |
| 동작 온도 | -40 C to +125 C |
| AEC-Q100 Grade | Automotive qualified |
| Configuration Memory | On-chip flash (non-volatile) |
| JEDEC Package Code | S-PBGA-B324 |
| Terminal Position | Bottom |
| 실장 유형 | Surface Mount |
| RoHS 상태 | Compliant |
10M08DCU324A7G s-pbga-b324 핀 구성 가이드
10M08DCU324A7G(s-pbga-b324 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: 10M08DCU324A7G.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
10M08DCU324A7G 적합 용도: 6 애플리케이션s: Automotive Body Electronics, Industrial Motor Control, Sensor Aggregation Hub, Display Controller / LVDS Bridge, Low-Cost Video Processing, I/O Expansion Bridge.
Automotive Body Electronics
The 10M08DCU324A7G's AEC-Q100 qualification and -40 C to +125 C operating range make it a strong fit for automotive body controllers and BCM (Body Control Module) designs. With 8,000 logic elements it can absorb multiple legacy 8/16-bit MCU functions into a single FPGA, reducing PCB area and BOM count. The on-die 12-bit ADC block digitizes analog sensor inputs (temperature, voltage, current) without external ADC chips, while 246 user I/O drive LEDs, MOSFET gates, LIN/CAN transceivers, and motor loads. The non-volatile flash configuration ensures instant-on behavior required by body-electronics power-up sequencing. Estimated: at typical 5V GPIO load, the device core draws under 200 mA active, simplifying power-tree design.
추천
Industrial Motor Control
The 10M08DCU324A7G is well suited for industrial motor-control and drives in the sub-1 kW range, integrating PWM generation, encoder feedback decoding, and protection logic on one device. Its 382 MHz internal clock supports deterministic control loop rates up to several hundred kHz. The on-die ADC measures phase currents via shunt resistors while the 246 user I/O support 3-phase gate-driver interfaces, brake control, and fault inputs. Pin-compatible migration to 10M04DCU324A7G is possible if lower logic density suffices, freeing 50% of the LE budget for cost optimization.
추천
Sensor Aggregation Hub
In IoT and industrial gateway designs, the 10M08DCU324A7G aggregates data from multiple sensors (temperature, pressure, flow, gas) over SPI, I2C, UART, or LVDS and forwards aggregated frames via Ethernet or CAN. The on-die flash stores both configuration and calibration tables, eliminating external EEPROM. The 246 user I/O allow direct fan-out to dozens of sensor channels without external muxing. AEC-Q100 qualification extends deployment to factory-floor and vehicle environments where temperature swings exceed consumer-grade limits.
추천
Display Controller / LVDS Bridge
The 10M08DCU324A7G can serve as a low-cost display controller or LVDS-to-RGB bridge in industrial HMI panels. Its LVDS-capable I/O pairs and PLL-based clock generation support common panel resolutions up to 1366x768 at 60 Hz. The 8K LE fabric comfortably implements timing controllers, dithering, and backlight dimming (PWM) on a single chip. Compared with discrete LCD-controller ICs, the FPGA allows late-stage resolution or timing changes without PCB rework.
추천
Low-Cost Video Processing
The 10M08DCU324A7G handles low-bandwidth video tasks such as format conversion (RGB-to-YUV), simple scaling, OSD overlay, and frame-rate conversion for industrial camera and inspection systems. Its embedded multiplier blocks implement pixel-pipeline arithmetic without external DSP chips. The on-die flash accelerates firmware iteration cycles since image processing parameters can be reloaded without external PROM reprogramming.
추천
I/O Expansion Bridge
The 10M08DCU324A7G is commonly deployed as an I/O expansion bridge connecting legacy processors (with too few GPIO) to additional buttons, LEDs, keypads, or peripheral buses. The 246 user I/O provide a generous fan-out budget, and the FPGA translates between I2C/SPI host commands and parallel GPIO operations. Non-volatile on-die configuration means instant host-processor visibility of all I/O at power-on without bootloader delay.
추천
추천 제품 요약
엔지니어링 참조 데이터: 10M08DCU324A7G — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | 10M08DCU324C8G | 10M08DCU324I7G | 10M08DCU324I7P | 10M04DCU324A7G | 10M04DCU324C8G |
|---|---|---|---|---|---|---|
| Brand | Intel | Intel | Intel | Intel | Intel | Intel |
| Package | 324-LFBGA (U324) | 324-LFBGA (U324) - same | 324-LFBGA (U324) - same | 324-LFBGA (U324) - same | 324-LFBGA (U324) - same | 324-LFBGA (U324) - same |
| Logic Elements (LE) | 8,000 | 8,000 | 8,000 | 8,000 | 4,000 (-50%) | 4,000 (-50%) |
| Embedded Memory (Kbits) | 246 | 246 | 246 | 246 | 189 (-23%) | 189 (-23%) |
| User I/O | 246 | 246 | 246 | 246 | 246 | 246 |
| Speed Grade | A7 | C8 (slower) | I7 | I7 | A7 | C8 |
| AEC-Q100 | Yes | Yes | Yes | Yes | Yes | Yes |
| User Flash (Kbits) | 378 | 378 | 378 | 378 | 295 (-22%) | 295 (-22%) |
주요 차별점
- Highest-density DCU MAX 10 in the U324 footprint (vs 10M04DCU324A7G)
- Automotive A7 speed grade, -40 C to +125 C range (vs 10M08DCU324C8G)
- Non-volatile on-die flash configuration (vs 10CL040ZU256I8G (Cyclone 10 LP))
설계 노트
Estimated: at industrial extreme of 125 C ambient with all 246 I/O driving 3.3 V CMOS loads at moderate toggle rates, the 10M08DCU324A7G core dissipation is approximately 0.5-0.8 W. The 324-LFBGA's theta_JA of approximately 18 C/W (with 4-layer PCB thermal vias under the die) yields a junction-to-ambient rise of roughly 15 C. A thermal-via array beneath the package center ball grid is essential for AEC-Q100 conformance. Avoid placing the FPGA directly above a hot power-MOSFET to minimize thermal coupling.
The 324-LFBGA requires a 0.8 mm ball pitch with microvia or via-in-pad PCB technology for reliable assembly. Decoupling follows the MAX 10 Hardware Design Guide: at least one 0.1 uF X7R per VCCIO pin group, plus 4.7 uF bulk caps at each supply rail. Maintain 4-5 decoupling caps within 5 mm of the package perimeter. The dedicated GND balls should connect to an inner ground plane via short, low-inductance microvia fanouts.
Do not assume all 246 user I/O are simultaneously usable - bank-voltage mix and configuration mode (single-image vs dual-image) reduce available I/O. Pin 1 location differs between U324 and F484 packages; never reuse a U324 layout for F484 BOM swaps. The on-die flash requires a 1.15-1.25 V VCCINT with tight 3% regulation; exceeding 1.25 V during configuration can corrupt flash content. Always specify the exact -A7 / -C8 / -I7 speed-grade in your BOM to avoid timing-closure surprises.
규정 준수 정보
AEC-Q100 qualified per manufacturer datasheet. RoHS and REACH compliance per Intel/Altera product page. Halogen-free status not explicitly stated in retrieved data.
