6EDL04N02PRXUMA1 - 200V 3-Phase Gate Driver IC | Infineon
부품 번호: 6EDL04N02PRXUMA1 ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $4.28 | $4.28 |
| 10 | $3.86 | $38.60 |
| 100 | $3.42 | $342.00 |
| 500 | $2.96 | $1,480.00 |
| 1,000 | $2.59 | $2,590.00 |
| 2,500 | $2.32 | $5,800.00 |
6EDL04N02PRXUMA1 개요
A gate driver IC is a specialized power management semiconductor that sits between a low-power microcontroller/MCU and a high-power switching transistor stage, translating 3.3 V or 5 V logic-level PWM signals into high-current gate drive signals capable of rapidly switching MOSFETs or IGBTs. Gate drivers belong to the broader hierarchy of power management ICs, then PMIC > driver > half/full/three-phase gate driver, and are critical building blocks in motor drives, solar inverters, and switched-mode power supplies.
Key features of the 6EDL04N02PRXUMA1 include integrated bootstrap diodes (BSD) for the three high-side drivers - eliminating the need for external bootstrap diodes and reducing BOM cost and PCB area - plus a dedicated fault output pin (nFAULT) that signals desaturation/over-current events to the host MCU. Each phase pair includes hardware interlocking to prevent shoot-through cross-conduction, and a single EN pin enables clean start-up sequencing. CMOS/LSTTL-compatible inputs accept 3.3 V logic directly, simplifying interface to modern MCUs.
The device is built on Infineon's proprietary thin-film SOI process, which provides excellent negative VS transient immunity (a critical spec for high-side switching in motor drives), latch-up immunity, and low power dissipation. The maximum junction temperature is +150 °C and the operating supply range is 10 V to 20 V VCC, with a separate logic-level supply on VBS for each high side.
Typical applications include 3-phase brushless DC (BLDC) motor drives for home appliances and HVAC fans, low-voltage (24 V to 96 V) industrial servo drives, e-bike and e-scooter traction inverters, and small solar/string inverter stages. The integrated bootstrap diode simplifies PCB layout and improves long-term reliability by reducing the part count.
When designing with this driver, ensure the VCC decoupling is sized for the total gate charge of all six switches switched simultaneously, and keep the bootstrap capacitor loop area minimal. The over-current protection uses a single shunt resistor on the low-side return path; place the RC filter on the ITRIP/CIN pin within 10 mm of the IC to avoid false tripping.
This page synthesizes distributor pricing across six sources, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
드롭인 대체품: 6EDL04N02PRXUMA1 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: 6EDL04N02PRXUMA1 (동일 폼 팩터 및 풋프린트) — 차이점: Package, Bootstrap Diode, Product Type, Blocking Voltage, Driver Configuration.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
6EDL04N02PR
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
6ED003L02F2XUMA1
✅ 드롭인✓ 재고 있음
$3.31 / 개
데이터시트 보기 →6EDL04N02PRXUMA1 최대 정격 & 전기적 특성
| Product Type | 3-Phase Gate Driver IC |
| Driver Configuration | Half-bridge (3 high-side + 3 low-side) |
| Maximum Blocking Voltage | +180 V (VS referenced to GND for high side) |
| Rated Supply Voltage (VCC) | 200 V class (operating range 10 V to 20 V on VCC) |
| Source Current (typ.) | 0.375 A |
| Sink Current (typ.) | 0.75 A |
| Bootstrap Diode | Integrated (BSD) on all 3 high-side drivers |
| Over-Current Protection | Yes (single-shunt, ITRIP/CIN pin) |
| Enable Pin (EN) | Yes (active-high) |
| Fault Output (nFAULT) | Yes (active-low, open-drain) |
| Input Logic Compatibility | CMOS / LSTTL, 3.3 V and 5 V |
| Interlocking / Anti-shoot-through | Yes (built-in per phase pair) |
| Process Technology | Thin-film SOI (Silicon-On-Insulator) |
| 동작 온도 범위 | -40 °C to +125 °C |
| Maximum Junction Temperature | +150 °C |
| 패키지 | PG-TSSOP-28 (28-pin, 4.40 mm width, exposed pad) |
| 실장 유형 | Surface Mount |
| Target Switches | MOSFETs up to 180 V, IGBTs up to 180 V |
| RoHS 상태 | Compliant |
6EDL04N02PRXUMA1 핀 구성
| 핀 1 | HIN1 — High-side input 1 (logic) |
| 핀 2 | HIN2 — High-side input 2 (logic) |
| 핀 3 | HIN3 — High-side input 3 (logic) |
| 핀 4 | LIN1 — Low-side input 1 (logic) |
| 핀 5 | LIN2 — Low-side input 2 (logic) |
| 핀 6 | LIN3 — Low-side input 3 (logic) |
| 핀 7 | EN — Enable (active high) |
| 핀 8 | nFault — Fault indicator (active low, open-drain) |
| 핀 9 | ITRIP/CIN — Over-current threshold / comparator input |
| 핀 10 | VSS — Logic ground |
| 핀 11 | VCC — +15 V supply for low-side drivers |
| 핀 12 | LO1 — Low-side gate output 1 |
| 핀 13 | LO2 — Low-side gate output 2 |
| 핀 14 | LO3 — Low-side gate output 3 |
| 핀 15 | COM — Low-side return (negative VS reference) |
| 핀 16 | VS1 — High-side phase 1 return |
| 핀 17 | HO1 — High-side gate output 1 |
| 핀 18 | VB1 — High-side bootstrap supply 1 |
| 핀 19 | VS2 — High-side phase 2 return |
| 핀 20 | HO2 — High-side gate output 2 |
| 핀 21 | VB2 — High-side bootstrap supply 2 |
| 핀 22 | VS3 — High-side phase 3 return |
| 핀 23 | HO3 — High-side gate output 3 |
| 핀 24 | VB3 — High-side bootstrap supply 3 |
| 핀 25 | NC — Not connected (per datasheet) |
| 핀 26 | NC — Not connected (per datasheet) |
| 핀 27 | NC — Not connected (per datasheet) |
| 핀 28 | EP — Exposed thermal pad (connect to VSS or large copper) |
일반적인 애플리케이션
6EDL04N02PRXUMA1 적합 용도: 7 애플리케이션s: 3-Phase BLDC Motor Drive (24-96 V), E-Bike / E-Scooter Traction Inverter, Small Solar String Inverter (≤180 V), HVAC Fan and Pump Motor Drives, Industrial Servo Drive (Low-Voltage), Cordless Power Tool Drives (≥36 V), Robotics / Drone BLDC Motor Stage.
3-Phase BLDC Motor Drive (24-96 V)
The 6EDL04N02PRXUMA1 is purpose-built for low-voltage 3-phase BLDC motor drives in the 24 V to 96 V bus range, where its +180 V VS blocking and 0.375 A source / 0.75 A sink drive are more than adequate for typical MOSFET half-bridges. Integrated bootstrap diodes remove six external parts and shrink the driver section by roughly 40%. The single-shunt OCP scheme pairs with most commodity FOC control MCUs to deliver complete hardware cycle-by-cycle protection. Compared to a discrete IR2114 x3 design, this IC cuts PCB area by half and drops BOM cost by 25-35%.
추천
E-Bike / E-Scooter Traction Inverter
E-bike and e-scooter traction inverters operating on 36 V or 48 V battery packs benefit from the 6EDL04N02PRXUMA1's compact PG-TSSOP-28 footprint, integrated bootstrap diodes, and built-in OCP that protects the battery during regen-braking current spikes. With 0.75 A sink capability, gate-drive losses stay low even with high-Qg MOSFETs; designers can switch above 25 kHz to keep the motor silent. The exposed thermal pad plus the SOI technology's negative VS transient immunity are essential for the harsh automotive-grade e-mobility environment. LCSC stocks 2,500-piece reels ideal for mid-volume e-bike production.
추천
Small Solar String Inverter (≤180 V)
For sub-180 V string-inverter power stages (single 60-cell panel or two panels in series), the 6EDL04N02PRXUMA1 provides the six-drive outputs plus OCP needed to drive a 3-phase MOSFET H-bridge used in some isolated micro-inverter topologies. The integrated BSDs reduce assembly cost in outdoor power electronics where reliability and reduced part count matter. Negative VS transient immunity from the SOI process is critical when the inverter feeds reactive loads or suffers from high dv/dt switching transients. Operating ambient of -40 °C to +125 °C covers outdoor enclosure ratings.
추천
HVAC Fan and Pump Motor Drives
Residential HVAC fans and water pumps increasingly use BLDC motors for efficiency, and the 6EDL04N02PRXUMA1 is an ideal driver for these sub-180 V appliances. Its integrated fault reporting (nFAULT) lets a low-cost MCU shut down safely on rotor lock, over-current, or over-temperature events without external comparator circuitry. Anti-shoot-through interlocking eliminates MCU dead-time software errors that would otherwise destroy the bridge during a firmware bug. PG-TSSOP-28 package is reflow-compatible with consumer HVAC contract-manufacturer lines.
추천
Industrial Servo Drive (Low-Voltage)
Low-voltage industrial servo drives for factory automation - typically 48 V to 96 V DC bus - use the 6EDL04N02PRXUMA1 to drive 3-phase servo motors with precise PWM control. The 3.3 V-compatible logic inputs pair directly with modern Cortex-M4/M7 servo MCUs (no level shifter needed), reducing design complexity and BOM count. Hardware interlocking and ITRIP-based OCP satisfy IEC 61800-5-1 functional safety requirements for industrial drives. RoHS and halogen-free compliance per Infineon's declaration supports industrial product environmental certifications.
추천
Cordless Power Tool Drives (≥36 V)
Cordless drills, saws, and outdoor power tools with 36 V or 48 V battery packs use the 6EDL04N02PRXUMA1 as the main bridge driver for high-current BLDC motors. The 0.75 A sink drive strength handles the high-Qg MOSFETs preferred in tools that must deliver peak torque of 80 Nm+. Integrated OCP protects the battery during stall events, while the nFAULT output triggers MCU-controlled emergency stop. Wide operating temperature range supports the hot-ambient conditions inside tool housings.
추천
Robotics / Drone BLDC Motor Stage
Compact 24 V to 72 V BLDC motor stages in robotics, drones, and small UAVs benefit from the 6EDL04N02PRXUMA1's small PG-TSSOP-28 footprint and 4.40 mm width. Weight and area are premium, so the integrated bootstrap diodes save critical board space on the ESC (Electronic Speed Controller). SOI technology's negative VS transient immunity keeps the driver robust against the regenerative energy spikes common in brushless ESC application. Operating temperature of -40 °C to +125 °C handles outdoor drone operating conditions.
추천
추천 제품 요약
엔지니어링 참조 데이터: 6EDL04N02PRXUMA1 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | 6EDL04N02PR | 6ED003L02F2XUMA1 |
|---|---|---|---|
| Brand | Infineon | Infineon | Infineon |
| Package | PG-TSSOP-28 | PG-TSSOP-28 (same) | PG-DSO-28 (same 28-pin) |
| Blocking Voltage | +180 V | +180 V | +600 V |
| Bootstrap Diode | Integrated (3x) | Integrated (3x) | Integrated (3x) |
| Over-Current Protection | Yes (single shunt) | Yes (single shunt) | Yes (single shunt) |
| Fault Reporting | nFAULT pin | nFAULT pin | nFAULT pin |
| Process Technology | Thin-film SOI | Thin-film SOI | Thin-film SOI |
| Unit Price (1 pc, 2026-09-14) | USD 4.28 | USD ~3.95 | USD ~3.75 |
주요 차별점
- All-in-one 3-phase driver in a single TSSOP-28 (vs IR2114STRPBF (requires 3 ICs + 6 external diodes))
- Integrated bootstrap diodes (vs Discrete bootstrap diodes (typical discrete driver design))
- Built-in over-current protection with fault reporting (vs Discrete driver (no OCP, requires external comparator))
- Thin-film SOI level-shifter for negative VS immunity (vs Older junction-isolation drivers (e.g. IR2104))
설계 노트
Estimated: at VCC = 15 V, switching six MOSFETs each with Qg = 30 nC at 20 kHz, total gate-drive power = 6 × 30 nC × 15 V × 20 kHz = 0.54 W. The PG-TSSOP-28 exposed pad has theta_JA of approximately 60 C/W on a JEDEC 4-layer test board; ensure at least 25 mm² of top-layer copper under the EP pin. Add a 10 µF / 25 V X7R ceramic bypass capacitor on VCC within 5 mm of pin 11, plus a 100 nF high-frequency decoupling cap within 2 mm. This is critical for reliable gate-drive operation.
Keep the high-side switching loops (VBx, VSx, HOx to FET) as small as possible - aim for loop area under 50 mm² to minimize parasitic inductance that causes VS undershoot below COM. The bootstrap capacitor (1 µF to 4.7 µF X7R) should be placed within 2 mm of each VBx-VSx pair. The ITRIP/CIN pin filter (typically 1 kΩ + 1 nF) must be within 10 mm of pin 9 to avoid false OCP trips. Star-ground the VSS pin and EP pad to a single point on the low-side shunt return.
Estimated: continuous 1 A drive current at 25 kHz with Qg = 50 nC dissipates P_total = 6 × 50e-9 × 15 × 25e3 = 0.113 W in the driver itself (negligible). However, the IC will also absorb shoot-through energy if dead-time is too short; aim for 200-500 ns dead-time on the MCU side. Total dissipation is dominated by the FETs, not the driver, but place a small copper pour under the EP for margin.
Common pitfalls when designing with this part include: (1) omitting the bootstrap capacitors on VBx - the high side will not switch without these. (2) Driving LIN1-3 or HIN1-3 with 5 V logic when the VCC is only 10 V - logic levels relative to VSS still work but check VIL spec. (3) Forgetting that nFAULT is open-drain and needs a pull-up to the MCU's logic rail. (4) Using the EN pin as a high-impedance input - it must be tied high (or driven) for normal operation, not left floating.
규정 준수 정보
RoHS and REACH compliant per Infineon product declaration. Lead-free and halogen-free per 'XUMA1' shipping suffix. Not AEC-Q100 qualified - this is a commercial/industrial part; consult Infineon sales for automotive-grade equivalents in the same family.
