AD53/009-9 - 40-Channel 14-Bit Parallel DAC | Analog Devices
부품 번호: AD53/009-9 ✓ 활성AD53/009-9 개요
A digital-to-analog converter is a data-acquisition IC that converts digital codes into proportional analog voltages or currents. Its functional hierarchy runs from converter to DAC, then to data-conversion IC and analog signal-chain component. In a multi-channel implementation, one converter can replace dozens of discrete output stages, simplifying firmware-driven level control while reducing wiring and synchronization overhead. The AD53/009-9 is particularly relevant where 14-bit output resolution and 40 parallel-output channels are required in one device.
The principal features include 40 voltage-output channels, 14-bit resolution, a parallel digital interface, and a single-supply architecture. The TQFP-80 package provides the pin count needed for the parallel data bus and analog output connections. The low 115 μA operating-current figure makes the converter appropriate for low-power telemetry, communications, and embedded test equipment, provided the total system power budget is checked against the selected output range and update rate.
The AD53/009-9 is associated with GSM baseband and wireless communications signal-generation applications. A parallel-interface DAC is useful where the host processor must update many outputs in a deterministic sequence, such as baseband modulation, transmit-path calibration, laboratory stimulus generation, or programmable test fixtures. Because the converter uses 14-bit words, one output code represents 16,384 discrete levels, supporting fine control where coarse 8-bit or 10-bit outputs would introduce visible quantization steps.
Typical uses include GSM baseband test equipment, RF and communications calibration systems, multi-level control networks, industrial process-control instrumentation, automated test equipment, and general-purpose data-acquisition platforms. In these systems, the AD53/009-9 can generate control levels for multiple analog blocks while the parallel interface simplifies connection to a digital controller. System-level settling time, output reference accuracy, and output-noise specifications must be confirmed from the complete manufacturer datasheet before setting update rates.
When laying out the board, route the parallel data bus with controlled trace lengths and keep the analog outputs away from high-current switching nodes. Use a quiet reference source and follow the manufacturer recommendation for bypass capacitance and output-load conditions. Because the exact pin assignments and layout guidance are not shown on the product-page excerpts, use the pin-description table and recommended application circuit in the manufacturer datasheet when assigning tracks.
This page organizes the confirmed device identity, electrical envelope, package information, sourcing guidance, and engineering considerations for the AD53/009-9. It also provides design-focused application guidance and verification notes that help engineers evaluate the converter for multi-channel analog-output designs before committing to a production BOM.
드롭인 대체품: AD53/009-9 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 제품에는 사용 가능한 드롭인 대체품이 없습니다.
대체품 요청AD53/009-9 최대 정격 & 전기적 특성
| Number of DAC Channels | 40 channels |
| 분해능 | 14 bits |
| 출력 유형 | Single voltage-output DAC |
| Digital Interface | Parallel |
| Supply Voltage Range | 2.7 V to 3.6 V |
| Alternate Supply Voltage Range | 2.5 V to 5.5 V |
| Supply Configuration | Single supply |
| Operating Current | 115 μA |
| 패키지 | TQFP-80 (14 mm × 14 mm) |
| 실장 유형 | Surface mount |
| 핀 수 | 80 pins |
| Output Levels per Channel | 16,384 codes (14-bit resolution) |
| Technology | CMOS |
| Application Category | Data acquisition and telecom circuit |
AD53/009-9 tqfp-80 (14 mm × 14 mm) 핀 구성 가이드
AD53/009-9(tqfp-80 (14 mm × 14 mm) 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: AD53/009-9.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
AD53/009-9 적합 용도: 6 애플리케이션s: GSM Baseband Signal Generation, RF and Communications Calibration, Automated Test Equipment, Industrial Process-Control Levels, Programmable Test Fixtures, Low-Power Data-Acquisition Platforms.
GSM Baseband Signal Generation
The AD53/009-9 is suited to parallel multi-level generation in GSM baseband test and calibration equipment because it combines 40 voltage-output channels with 14-bit resolution. Each channel represents 16,384 discrete codes, supporting finer stimulus control than an 8-bit or 10-bit converter. The 80-pin TQFP package keeps the converter count low when many controlled levels are required, although the parallel bus must be routed with attention to timing. Confirm settling time, full-scale accuracy, and channel-to-channel matching against the modulation bandwidth before fixing the update schedule.
추천
RF and Communications Calibration
In RF and communications calibration equipment, the AD53/009-9 can provide multiple independently addressed analog levels from one controller. Its 40-channel parallel architecture reduces the number of discrete output stages, while 14-bit resolution gives 16,384 selectable steps per channel. The listed 115 μA operating-current figure is useful in low-power instrumentation, but reference quality and output settling determine usable accuracy. Use a low-noise reference, defined trace geometry, and the manufacturer recommended-load network to prevent calibration drift and channel interaction.
추천
Automated Test Equipment
The AD53/009-9 fits automated test equipment that must apply many analog stimulus points while coordinating data, clock, and channel-selection signals through a parallel interface. Forty 14-bit voltage outputs allow a single converter to replace numerous single-channel devices and simplify software addressing. The 2.7 V to 3.6 V listing range supports compact 3.3 V test systems, but fixture loading and cable capacitance can affect settling. Validate the complete analog path at the fixture and place output buffering near the connector when long cables are unavoidable.
추천
Industrial Process-Control Levels
The AD53/009-9 can supply multiple programmable voltage levels for industrial process-control and instrumentation subsystems where several actuator or test nodes require independent commands. Its 40 channels and 14-bit resolution provide 16,384 discrete levels on each output, enabling fine set-point adjustment without a large bank of discrete dividers. The low 115 μA operating current supports compact control electronics, provided channel update rates match the process-control loop. Keep sensitive analog routing away from switching power stages and use the manufacturer grounding recommendations.
추천
Programmable Test Fixtures
Programmable test fixtures benefit from the AD53/009-9 because 40 voltage outputs can emulate multiple expected conditions without duplicating converter circuitry across the fixture. The parallel interface allows a controller to update a defined set of channels in a deterministic sequence, while 14-bit resolution supports precise level selection. For long fixture wiring, treat the converter outputs as a starting point and add appropriate buffering where capacitance or crosstalk could affect settling. Verify channel order and update timing in firmware against the manufacturer pin and timing tables.
추천
Low-Power Data-Acquisition Platforms
The AD53/009-9 is applicable to low-power data-acquisition platforms that require numerous controllable analog outputs rather than high-rate waveform generation. Its 40 channels provide broad control flexibility, 14-bit resolution supplies 16,384 codes per output, and the 115 μA operating-current figure supports compact power budgets. A parallel bus is advantageous when the host processor drives several channels concurrently, but it requires enough board area for the 80-pin TQFP and careful signal-integrity work. Use the datasheet settling-time curves to set the maximum channel-update rate.
추천
추천 제품 요약
엔지니어링 참조 데이터: AD53/009-9 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 |
|---|---|
| Brand | Analog Devices |
| Package | TQFP-80 (14 mm × 14 mm) |
| Number of DAC Channels | 40 channels |
| Resolution | 14 bits |
| Output Configuration | Single voltage-output |
| Digital Interface | Parallel |
| Supply Voltage | 2.7 V to 3.6 V |
| Operating Current | 115 μA |
| Technology | CMOS |
| Application Category | Data acquisition and telecom circuit |
주요 차별점
- High channel density in a single converter (vs AD504SH)
- Fourteen-bit command resolution (vs AD503JH)
- Parallel multi-channel interface (vs AD506JH)
설계 노트
Route the parallel data, address, and clock signals as a controlled-length bus, and keep the 80-pin TQFP footprint free of unrelated high-current switching paths. Confirm every terminal assignment in the manufacturer pin-description table before schematic capture. Because the converter provides 40 analog outputs, allocate analog routing away from digital return currents and use a continuous ground reference beneath the device where the recommended layout permits it.
Use the manufacturer settling-time curves to set the minimum interval between an output-code update and a measurement. The 14-bit resolution produces 16,384 steps, but useful accuracy can be limited by output noise, reference quality, load capacitance, and incomplete settling. Do not infer timing from resolution alone. Check the complete datasheet for recommended loads, output buffers, and reference-source impedance, and preserve those conditions in the final board layout.
Confirm the actual supply range for the ordered grade using the complete Analog Devices datasheet, since product summaries show both 2.7 V to 3.6 V and 2.5 V to 5.5 V descriptions. Place the manufacturer-recommended bypass capacitors next to the supply terminals and keep reference-decoupling connections short. Treat the 115 μA operating-current figure as a baseline rather than a complete system-power estimate because reference current and output-load conditions also contribute.
규정 준수 정보
Compliance declarations are not identified in the product-page excerpts. Confirm RoHS, REACH, halogen-free, and conflict-minerals status for the exact ordered part number with the manufacturer or the authorized supply channel before release.