AD704AN - Quad Picoampere Input Op Amp | Analog Devices
부품 번호: AD704AN ✓ 활성AD704AN 개요
An operational amplifier is an analog signal-conditioning IC that compares voltages applied to its inverting and non-inverting inputs and amplifies the difference. The AD704 belongs to the bipolar operational-amplifier hierarchy, where bipolar input transistors provide low-voltage operation and precision analog performance without the input leakage normally associated with BiFET input stages. Four amplifiers are integrated into one package for instrumentation, measurement, sensor-signal conditioning, and precision analog systems.
The AD704's defining benefit is its combination of very low input bias current and unusually stable bias-current behavior over temperature. Analog Devices describes the circuit as a low-power bipolar op amp with picoampere input current, using SuperBeta bipolar input transistors to achieve input bias current comparable to FET-input amplifiers at room temperature. This makes the device relevant when source leakage or measurement drift could obscure a small sensor signal.
The device combines four unity-gain-stable amplifiers with an open-loop gain of 132 dB and a slew rate of 150 V/ms. Its 75 uV input offset voltage supports precision signal conditioning, while the stated 15 mA supply current reflects the low-power design goal. A 2 V to 18 V total supply range provides flexibility between low-voltage instrumentation systems and conventional ±18 V analog environments. The built-in compensation and ESD protection indicated by the product listing reduce external circuit complexity.
Typical uses include pH and chemical sensors, photodiode and optical-measurement front ends, laboratory instrumentation, low-current transducers, and precision analog signal-conditioning boards. Four independent amplifiers in one package can simplify channel-count designs when four similar low-leakage front ends are required. Board-area savings must be weighed against the larger through-hole footprint of the PDIP-14 package compared with a modern surface-mount quad op amp.
When designing around the AD704AN, prioritize input-source leakage, input-bias-current drift, offset voltage, and the bias network around each amplifier. Keep sensitive input traces away from power switches, high-impedance nodes, and exposed pad connections in other components. Confirm common-mode range, output swing, noise, stability, and maximum input differential voltage against the manufacturer's datasheet for the exact operating conditions.
This page consolidates the AD704AN's principal electrical characteristics, package information, application guidance, and same-family ordering alternatives into an engineering-focused selection reference. It also identifies the distinctions that must be checked before using a temperature-grade or lead-free ordering code as a replacement.
드롭인 대체품: AD704AN — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
AD704ANZ
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
AD704BNZ
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
AD704CNZ
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
AD704JN
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →AD704KN
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
AD704AN 최대 정격 & 전기적 특성
| Amplifier Type | Quad precision bipolar operational amplifier |
| Number of Channels | 4 channels |
| Input Bias Current | 80 pA |
| Maximum Input Bias Current | 150 pA |
| Input Bias Current Temperature Drift | 1 uV/°C |
| Input Offset Voltage | 75 uV |
| Open-Loop Gain | 132 dB |
| Slew Rate | 150 V/ms |
| Supply Voltage Range | 2 V to 18 V |
| 공급 전류 | 15 mA |
| 동작 온도 범위 | -40°C to +85°C |
| 패키지 | 14-pin PDIP |
| Compensation | Built-in compensation |
| ESD Protection | Built-in ESD protection |
| Input Transistor Technology | SuperBeta bipolar input transistors |
| 수명 주기 상태 | PRODUCTION |
AD704AN 14-pin pdip 핀 구성 가이드
AD704AN(14-pin pdip 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: AD704AN.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
AD704AN 적합 용도: 6 애플리케이션s: High-Impedance Sensor Signal Conditioning, pH and Electrochemical Measurement, Optical and Photodiode Front Ends, Laboratory Instrumentation and Measurement, Low-Current Transducer Amplification, Battery-Powered Precision Analog Systems.
High-Impedance Sensor Signal Conditioning
The AD704AN fits precision front ends for high-impedance sensors where source leakage must remain small relative to the amplifier input. Its 80 pA input bias current and 1 uV/°C input-bias-current drift help reduce errors as source impedance and temperature vary, while 132 dB open-loop gain supports accurate amplification of small differential signals. Four amplifiers can condition four similar sensor channels in one package. Place the amplifier close to the sensor, protect high-impedance nodes with guarding, and verify that connector leakage and PCB contamination remain below the required error budget.
추천
pH and Electrochemical Measurement
Electrochemical and pH sensors can present very high source impedance, making input bias current and its temperature drift important error sources. The AD704AN's 80 pA input bias current, low 1 uV/°C drift, and 75 uV input offset voltage support low-level signal conditioning without the larger bias current typical of conventional bipolar inputs. Its four-channel arrangement allows several electrode channels to share one package type. Use guarded traces, clean connectors, and low-leakage protection networks, and confirm electrode-specific common-mode and output-swing requirements in the manufacturer's datasheet.
추천
Optical and Photodiode Front Ends
The AD704AN is suitable for low-current optical front ends where the amplifier should introduce minimal input bias current. Its 80 pA bias current helps preserve weak photodiode currents, and the 150 V/ms slew rate provides useful bandwidth for moderate transient response. The 14-pin PDIP package also supports prototyping and manual rework in precision laboratory equipment. The practical trade-off is a larger board footprint than a surface-mount quad amplifier. Place the device near the photodiode, use low-leakage guarding, and account for diode capacitance when evaluating stability.
추천
Laboratory Instrumentation and Measurement
The AD704AN supports precision laboratory measurement circuits where low input current and stable bias behavior determine the usable resolution. Its four amplifiers can implement buffer, gain, difference, and active-feedback functions while sharing a 2 V to 18 V supply capability. The 132 dB open-loop gain and 75 uV offset voltage are valuable when scaling small sensor outputs, although noise and gain-bandwidth requirements must still be checked for each circuit. A grounded guard around sensitive inputs and short feedback paths will help preserve measurement integrity.
추천
Low-Current Transducer Amplification
For current-output or resistive transducers, the AD704AN can provide low-input-bias-current amplification with enough open-loop gain for high-impedance feedback networks. The 80 pA typical input bias current minimizes loading, and the 1 uV/°C drift specification helps control temperature-dependent measurement shifts. Four channels reduce the number of packages required in a multi-axis or multi-sensor instrument. The designer should still verify output swing, common-mode limits, noise, and stability with the actual feedback components, because those operating limits are not determined by the headline gain and bias-current ratings alone.
추천
Battery-Powered Precision Analog Systems
The AD704AN is appropriate for portable or battery-powered analog systems that require low bias current without moving to a MOSFET-input amplifier. Its listed 15 mA supply current and 2 V to 18 V supply range provide a practical operating envelope for low-voltage instrumentation and industrial signal-conditioning designs. The tradeoff is that bipolar input bias current can change more over temperature than a conventional BiFET input stage. Use low-leakage protection devices, verify the complete power budget, and confirm that transient current and shutdown behavior satisfy the battery system's load profile.
추천
엔지니어링 참조 데이터: AD704AN — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
Choose AD704ANZ when its lead-free ordering configuration satisfies procurement requirements and its electrical ratings match the original design. Consider the other listed AD704 family codes only after checking their exact temperature grade, electrical limits, and ordering status against the manufacturer's table. The listed MC3403DR can be considered when a general-purpose quad amplifier is sufficient and the lower bias current and drift of the AD704AN are unnecessary, but it should not be treated as a direct replacement without measurement-level verification. For any proposed substitute, confirm pin functions, package geometry, common-mode range, output swing, stability, input capacitance, and input leakage.
대체품과의 비교
| 파라미터 | 이 제품 | AD704ANZ | AD704BNZ | AD704CNZ | AD704JN | AD704KN |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 14-pin PDIP | 14-pin PDIP | 14-pin PDIP | 14-pin PDIP | 14-pin PDIP | 14-pin PDIP |
| Amplifier Count | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
주요 차별점
- Exceptionally low input bias current for a bipolar amplifier (vs MC3403DR)
- Low input-bias-current drift (vs MC3403DR)
- Four amplifiers with strong open-loop gain (vs MC3403DR)
- Single-package supply-range flexibility (vs AD704ANZ)
설계 노트
Keep each high-impedance input short, clean, and surrounded by a grounded guard where practical. Avoid routing sensitive inputs beside switching-regulator traces, relay contacts, test points, or unshielded connector pins. Surface contamination and connector leakage can become significant when the amplifier's input bias current is only 80 pA. Use clean assembly practices, conformal protection when appropriate, and separate the sensitive analog return path from high-current output paths.
Do not assume that low input bias current eliminates all DC error. Account for the stated 75 uV input offset voltage, 1 uV/°C bias-current drift, resistor tolerance, leakage through protection components, and error caused by input and output common-mode limits. Check the manufacturer's operating-table conditions against the actual supply voltage, output load, channel configuration, and temperature range before treating the headline specifications as unconditional limits.
Use a conventional 14-pin PDIP footprint and verify pin-1 orientation against the manufacturer's package drawing. Place input and feedback components close to their associated amplifier pins to minimize parasitic capacitance and leakage. Because the device supports four independent channels, preserve channel symmetry in analog routing and grounding so that one channel does not inherit another channel's switching or thermal disturbance.
Evaluate stability with the actual source capacitance, feedback network, load, and supply decoupling. The 150 V/ms slew rate provides adequate response for many precision measurement signals, but speed alone does not establish usable bandwidth in a noisy or capacitive source. Keep supply bypass capacitance close to the device, maintain short feedback loops, and test the completed board for oscillation before adding input protection networks that add capacitance or leakage.
규정 준수 정보
The AD704 is identified as a production product, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations are stated in the available product information. AEC-Q100 is not applicable to this general-purpose analog amplifier.