Analog Devices

AD9100JD - Ultrahigh-Speed Track-and-Hold | Analog Devices

부품 번호: AD9100JD ✗ 단종
20-lead side-brazed skinny DIP ceramic package Package Less than 83 dBfs Speed
MOQ: 1 |

AD9100JD 개요

Analog Devices AD9100JD is an ultrahigh-speed monolithic track-and-hold amplifier with 13 ns acquisition time to 0.1% accuracy, 16 ns acquisition time to 0.01% accuracy, and 250 MHz tracking bandwidth in a 20-lead side-brazed skinny DIP package.

A track-and-hold amplifier is a sampling circuit that captures an input voltage during a controlled track interval and then holds that voltage for conversion or measurement. Within the signal-chain hierarchy, the AD9100JD sits between a high-speed source and a downstream analog-to-digital converter, acting as a sampling bridge with a dedicated hold amplifier. Its mature high-speed complementary bipolar process and low-parasitic custom package support demanding high-speed and high-dynamic-range signal acquisition.

Key performance includes hold-mode distortion below 83 dBfs while sampling at 30 MSPS for analog input frequencies up to 12 MHz, and -74 dBfs at 20 MHz. The device also maintains less than 1 ps aperture jitter, supports capacitive loads up to 100 pF with little degradation in acquisition time, and provides 83 dB feedthrough rejection at 20 MHz. These characteristics make timing accuracy, isolation between track and hold intervals, and sampled-waveform fidelity central design considerations.

The AD9100JD uses a high-speed complementary bipolar process to achieve rapid settling during acquisition and low signal distortion during the hold interval. Its 250 MHz tracking bandwidth accommodates rapidly changing input waveforms, while the short acquisition interval reduces the time required to settle to the requested accuracy. The custom 20-lead package minimizes parasitic effects and supports the high-frequency behavior needed in sampling systems. A sidelong ceramic package also reflects its role as a high-performance laboratory and instrumentation component rather than a cost-sensitive production package.

Typical applications include high-speed data-acquisition front ends, flash and pipeline ADC input stages, pulsed signal capture, communications test equipment, spectroscopy, phase-sensitive measurements, and precision waveform instrumentation. The AD9100JD is particularly appropriate when a system requires 30 MSPS operation, accurate sub-1 ps aperture timing, low feedthrough, or acquisition into a substantially capacitive input network.

A critical design practice is to control clock and analog-signal routing so that clock feedthrough does not contaminate the held output. Keep the sampling clock away from sensitive input and output traces, terminate unused inputs appropriately, and use the package pin description and recommended application circuit in the Analog Devices datasheet when assigning the board layout. High-speed sampling performance also requires short return paths, a quiet reference source, and careful decoupling.

This product page combines the manufacturer specifications with application guidance, design cautions, pin and package information, verified lifecycle context, and a qualification search for true same-package replacements. That engineering-focused synthesis helps distinguish direct drop-in options from merely similar track-and-hold devices and supports faster component selection for high-speed acquisition systems.

드롭인 대체품: AD9100JD — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

이 시리즈의 변형

다음과 드롭인 호환되는 동일 시리즈 모델: AD9100JD (동일 폼 팩터 및 풋프린트) — 차이점: Product Type.

Analog Devices
Product Type: 1 ultrahigh-speed monolithic track-and-hold circuit
비교 대상: AD9100JD →

이 제품에는 사용 가능한 드롭인 대체품이 없습니다.

대체품 요청

AD9100JD 최대 정격 & 전기적 특성

Product Type Monolithic track-and-hold amplifier
Acquisition Time to 0.1% Accuracy 13 ns
Acquisition Time to 0.01% Accuracy 16 ns
Maximum Sampling Rate 30 MSPS
Hold-Mode Distortion at 12 MHz Input and 30 MSPS Less than 83 dBfs
Hold-Mode Distortion at 20 MHz Input and 30 MSPS -74 dBfs
Tracking Bandwidth 250 MHz
Aperture Jitter Less than 1 ps
Feedthrough Rejection at 20 MHz 83 dB
Maximum Drive Capacitance 100 pF
Process Technology Mature high-speed complementary bipolar process
패키지 20-lead side-brazed skinny DIP ceramic package
Lead Count 20 leads
Temperature Grades Commercial, industrial, and military grades
883 Qualification Consult the factory for availability

AD9100JD 20-lead side-brazed skinny dip ceramic package 핀 구성 가이드

AD9100JD(20-lead side-brazed skinny dip ceramic package 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.

AD9100JD의 20-lead side-brazed skinny dip ceramic package 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: AD9100JD.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

AD9100JD 적합 용도: 6 애플리케이션s: High-Speed ADC Input Acquisition, Pulsed Signal Capture, Communications Waveform Instrumentation, Precision Spectroscopy Signal Capture, Phase-Sensitive Measurement, High-Speed Data-Acquisition Systems.

📡

High-Speed ADC Input Acquisition

The AD9100JD is suited to the sampling stage in front of a high-speed analog-to-digital converter because it acquires to 0.1% accuracy in 13 ns and reaches 0.01% accuracy in 16 ns. Its 250 MHz tracking bandwidth lets the input follow rapid transitions during the track interval, while less than 1 ps aperture jitter limits timing uncertainty in the conversion aperture. According to the Analog Devices AD9100 datasheet, hold-mode distortion is below 83 dBfs at a 12 MHz input when sampling at 30 MSPS. The designer should confirm converter polarity, input range, kickback behavior, and whether the converter requires a sample-and-hold function or a dedicated driver.

⚡

Pulsed Signal Capture

The AD9100JD can capture short-duration or rapidly changing events when the system needs both a wide tracking bandwidth and a defined hold interval. Its 250 MHz tracking bandwidth supports high-frequency input activity, and the 13 ns acquisition to 0.1% accuracy limits the interval required to settle before capture. Less than 1 ps aperture jitter also helps preserve the timing relationship between the sampled waveform and its trigger. For practical pulsed measurements, keep the clock and analog paths short, isolate high-energy trigger circuitry, and verify the sample-and-hold timing sequence against the 30 MSPS operating capability documented by Analog Devices.

🌐

Communications Waveform Instrumentation

The AD9100JD is appropriate for communications test equipment that must observe carrier-related waveforms with controlled sample timing. Its hold-mode performance reaches below 83 dBfs at a 12 MHz analog input and 30 MSPS sampling rate, while the value becomes -74 dBfs at a 20 MHz input according to the Analog Devices AD9100 datasheet. The sub-1 ps aperture jitter and 83 dB feedthrough rejection at 20 MHz help separate the intended sampled signal from timing-related artifacts. PCB implementation should use controlled impedance, a continuous return plane, and careful separation between the sampling clock and high-level signal paths.

🔬

Precision Spectroscopy Signal Capture

For spectroscopy instrumentation, the AD9100JD can capture detector or front-end outputs that require accurate settling before digitization. The 13 ns acquisition to 0.1% accuracy and 16 ns acquisition to 0.01% accuracy provide a defined settling interval, while less than 1 ps aperture jitter reduces uncertainty in the sampling instant. Its ability to drive loads up to 100 pF with little acquisition degradation can simplify interfacing to suitable amplifier or converter stages. The system designer should still account for detector noise, analog bandwidth, clock jitter, and conversion settling, because the track-and-hold amplifier does not correct noise or bandwidth limitations elsewhere in the signal chain.

📈

Phase-Sensitive Measurement

The AD9100JD supports phase-sensitive measurement systems where repeatable acquisition timing determines the integrity of an in-phase or quadrature result. Less than 1 ps aperture jitter limits sampling-time uncertainty, and the 250 MHz tracking bandwidth permits the amplifier to follow signals before the hold interval begins. Its 30 MSPS capability and low hold-mode distortion make it useful for synchronized detector measurements. Designers should minimize clock-to-input coupling, provide clean low-jitter sampling clocks, and use the manufacturer application circuit to establish the correct track and hold timing relative to the measurement cycle.

🖥️

High-Speed Data-Acquisition Systems

The AD9100JD fits the central sampling function of a high-speed data-acquisition system that must repeatedly acquire an analog waveform. The 13 ns acquisition time to 0.1% accuracy establishes a short aperture, 250 MHz tracking bandwidth accommodates fast-changing inputs, and the 100 pF load capability reduces sensitivity to capacitive loading. According to the Analog Devices AD9100 datasheet, hold-mode distortion below 83 dBfs is maintained at 30 MSPS for analog inputs up to 12 MHz. A robust implementation requires regulated supplies, local decoupling, low-inductance signal paths, and clock distribution whose jitter does not overwhelm the device's less-than-1-ps aperture-jitter capability.

추천 제품 요약

AD9100 Device-family reference 사용처: High-Speed ADC Input Acquisition, Pulsed Signal Capture, Communications Waveform Instrumentation, Precision Spectroscopy Signal Capture, Phase-Sensitive Measurement, High-Speed Data-Acquisition Systems AD9100JD Analog Devices 사용처: High-Speed ADC Input Acquisition, Pulsed Signal Capture, Communications Waveform Instrumentation, Precision Spectroscopy Signal Capture, Phase-Sensitive Measurement, High-Speed Data-Acquisition Systems
What are the key specifications of AD9100JD that engineers should know?
The AD9100JD combines 13 ns acquisition to 0.1% accuracy, less than 1 ps aperture jitter, 250 MHz tracking bandwidth, and operation up to 30 MSPS in a 20-lead side-brazed skinny DIP package. According to the Analog Devices AD9100 datasheet, its hold-mode distortion is below 83 dBfs at a 12 MHz analog input when sampling at 30 MSPS. It can also drive capacitive loads up to 100 pF with little degradation in acquisition time.
What is the operating voltage of AD9100JD?
The AD9100JD supply-voltage limits are not stated in the retrieved manufacturer material and must be confirmed from the pin-description and electrical-characteristics tables in the Analog Devices AD9100 datasheet. The specified behavior includes 30 MSPS sampling, 13 ns acquisition to 0.1% accuracy, and 250 MHz tracking bandwidth. Do not infer the permitted supply range from a related track-and-hold device because the package pinout and electrical limits are specific to the AD9100.
Where can I download the AD9100JD datasheet PDF?
The official Analog Devices AD9100 datasheet PDF is available at https://www.analog.com/media/en/technical-documentation/data-sheets/AD9100.pdf. It is the preferred document for the AD9100JD because it describes the monolithic track-and-hold amplifier, 13 ns and 16 ns acquisition performance, 30 MSPS operation, feedthrough rejection, the 20-lead package, and the recommended application arrangements. Use the package pin-description table before assigning connections.
Where can I find the AD9100JD pinout and package information?
The AD9100JD pinout should be taken from the Analog Devices AD9100 datasheet rather than inferred from a generic 20-pin package drawing. The manufacturer identifies a 20-lead side-brazed skinny DIP ceramic package, but the retrieved excerpt does not provide individual terminal names. Consult the datasheet pin-description table and package drawing for the exact pin numbering and signal assignments before laying out the PCB or assembling the device.
How fast does the AD9100JD acquire a signal?
The AD9100JD acquires a signal to 0.1% accuracy in 13 ns and to 0.01% accuracy in 16 ns. According to the Analog Devices AD9100 datasheet, the device combines this short acquisition interval with 250 MHz tracking bandwidth and less than 1 ps aperture jitter. These figures make it suitable for high-speed sample-and-hold stages operating at up to 30 MSPS, including ADC input conditioning and precision pulsed-waveform capture.
What is the hold-mode distortion of AD9100JD?
The AD9100JD provides hold-mode distortion below 83 dBfs when sampling at 30 MSPS with analog input frequencies up to 12 MHz. According to the Analog Devices AD9100 datasheet, the corresponding figure is -74 dBfs at a 20 MHz analog input. This behavior is especially relevant when the held waveform feeds a high-resolution ADC and residual switching or sampling artifacts could limit the achievable signal-to-noise ratio.
Can AD9100JD drive a capacitive ADC input?
The AD9100JD can drive capacitive loads up to 100 pF with little degradation in acquisition time. According to the Analog Devices AD9100 datasheet, this makes it suitable for isolation or buffering between a high-speed source and a sampling-capacitor-based converter. Confirm the final load, converter kickback, and settling requirements in the target system because a 100 pF load does not eliminate all dynamic settling and timing considerations.
What is the difference between AD9100JD and a general-purpose sample-and-hold IC?
The AD9100JD is a specialized ultrahigh-speed track-and-hold amplifier rather than a general-purpose slow sample-and-hold IC. According to the Analog Devices AD9100 datasheet, it offers 13 ns acquisition to 0.1% accuracy, less than 1 ps aperture jitter, 250 MHz tracking bandwidth, and 30 MSPS operation. Its custom low-parasitic package also supports high dynamic range, making it more appropriate for precision waveform and ADC-front-end applications.
When should I choose AD9100JD for an ADC front end?
Choose AD9100JD when the ADC front end requires very fast settling, low aperture jitter, and low hold-mode distortion. Its 13 ns acquisition to 0.1% accuracy, less than 1 ps aperture jitter, and 30 MSPS capability suit high-speed converters where input acquisition must occur within a narrow sampling interval. The track-and-hold arrangement must be matched to the converter architecture, clock polarity, input range, and external drive requirements shown in the manufacturer documentation.
What can replace AD9100JD?
No independently verified, pin-compatible drop-in replacement for the AD9100JD was identified in the available substitution records. A valid replacement must use the same 20-lead side-brazed skinny DIP footprint, preserve the pin assignments, and meet the critical acquisition-time, aperture-jitter, bandwidth, and distortion requirements. Similar track-and-hold amplifiers should not be treated as drop-in parts unless their package drawings and pin descriptions are confirmed to match.
Is AD9100JD suitable for pulsed signal and waveform capture?
The AD9100JD is suitable for pulsed signal capture because it tracks at 250 MHz, acquires to 0.1% accuracy in 13 ns, and has less than 1 ps aperture jitter. According to the Analog Devices AD9100 datasheet, its hold-mode distortion remains below 83 dBfs at a 12 MHz input and 30 MSPS sampling rate. Use clean trigger and clock routing to prevent timing or feedthrough errors from being mistaken for features in the captured waveform.
Where to buy AD9100JD online?
Use the Request a Quote form on this page to request AD9100JD availability, current commercial terms, and the appropriate package quantity. The component is an Analog Devices monolithic track-and-hold amplifier supplied in a 20-lead side-brazed skinny DIP ceramic package. Because availability can change with lifecycle and procurement conditions, request a written quotation that identifies AD9100JD exactly rather than accepting a generic or functional substitute.
What is the price of AD9100JD?
Request the current AD9100JD quotation through the Request a Quote form on this page. The product is a ceramic 20-lead track-and-hold amplifier and may be subject to lifecycle, allocation, and small-volume considerations that make a static quotation unsuitable. When requesting terms, specify the required quantity, date code requirements, inspection level, and whether multiple delivery locations are needed.
What is the lead time for AD9100JD?
The current AD9100JD lead time should be confirmed through the Request a Quote form on this page. The Analog Devices product material indicates that commercial, industrial, and military temperature grades are offered, but it does not establish a universal production lead time for every grade or quantity. Provide the required grade, package suffix, annual usage, and target assembly schedule so the quotation can reflect the correct configuration.
Is AD9100JD in stock?
Request current AD9100JD stock status through the Request a Quote form on this page. Stock availability should be tied to the exact manufacturer part number, temperature grade, package configuration, and order quantity. A general AD9100 family response does not establish availability of the AD9100JD suffix, so request written confirmation of the exact MPN before allocating it to a production schedule.
How should AD9100JD be handled in high-speed PCB layouts?
Route the sampling clock and sensitive analog signal away from each other and keep both paths short and controlled. According to the Analog Devices AD9100 datasheet, the custom package is intended to minimize parasitics and optimize dynamic performance, but external layout still affects clock feedthrough and acquisition behavior. Follow the manufacturer application circuit for decoupling and pin connections, provide a low-impedance return path, and treat unused terminals according to the datasheet.

엔지니어링 참조 데이터: AD9100JD — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the AD9100JD when the signal chain requires a dedicated high-speed track-and-hold stage with 13 ns acquisition to 0.1% accuracy, less than 1 ps aperture jitter, and 250 MHz tracking bandwidth. It is well suited to high-speed ADC interfaces, pulsed-waveform capture, communications instrumentation, spectroscopy, and phase-sensitive measurement. Its 20-lead side-brazed skinny DIP ceramic package is unusual in modern designs, so board area, assembly method, and sourcing should be checked early. Do not substitute a generic sample-and-hold amplifier solely because its acquisition time appears similar. A valid replacement must match the package geometry and exact pin assignments while also meeting bandwidth, jitter, distortion, and capacitive-drive requirements. If no verified pin-compatible candidate exists, retain the AD9100JD or plan a deliberate redesign rather than assuming an interchangeable part.

대체품과의 비교

파라미터 이 제품
Package 20-lead side-brazed skinny DIP ceramic package
Brand Analog Devices
Product Type Monolithic track-and-hold amplifier
Acquisition Time to 0.1% Accuracy 13 ns
Acquisition Time to 0.01% Accuracy 16 ns
Maximum Sampling Rate 30 MSPS
Tracking Bandwidth 250 MHz
Aperture Jitter Less than 1 ps
Hold-Mode Distortion at 12 MHz and 30 MSPS Less than 83 dBfs
Maximum Drive Capacitance 100 pF

주요 차별점

  • Very short acquisition interval (vs General-purpose sample-and-hold amplifiers)
  • Low sampling-aperture uncertainty (vs Conventional laboratory sample-and-hold stages)
  • High-speed tracking with strong isolation (vs General-purpose buffer-based acquisition stages)
  • Capacitive-load tolerance (vs Lower-drive sample-and-hold amplifiers)

설계 노트

Keep the sampling clock physically separate from the analog input, hold output, and reference pins. Route high-speed tracks as short and direct as practical, maintain a continuous return path, and avoid routing clock signals beneath sensitive analog nodes. The AD9100's custom package reduces package parasitics, but board-level coupling can still degrade the measured hold-mode behavior. Use the pin-description table and recommended application arrangement in the Analog Devices AD9100 datasheet when assigning the layout.

Treat the sampling clock as a precision timing signal because the AD9100 specifies less than 1 ps aperture jitter. Use short clock traces, a low-impedance driver, and a quiet return path, and avoid unnecessary switches or long stubs in the clock network. Separately evaluate total timing uncertainty, including the clock generator, distribution network, board skew, and input slew rate; the component's aperture-jitter figure alone does not establish the timing accuracy of the complete instrument.

Do not assume that any 20-pin sample-and-hold amplifier is a drop-in replacement for the AD9100JD. A valid replacement must reproduce the exact terminal assignments and side-brazed package geometry while meeting the 13 ns acquisition, 250 MHz tracking bandwidth, less-than-1-ps aperture jitter, and load requirements. Check the manufacturer pin-description table, package drawing, and application circuit before approving a substitute or changing the sourcing suffix.

Follow the manufacturer's recommended supply and decoupling arrangement in the AD9100 datasheet, placing bypass connections so that high-current return paths do not share impedance with sensitive analog nodes. Confirm the exact pin voltages against the electrical-characteristics table before applying power. Stable reference and supply conditions are particularly important because acquisition-time and distortion measurements can be influenced by reference or supply noise even when the sample-and-hold timing is correct.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

The Analog Devices product material identifies commercial, industrial, and military temperature grades and states that factory consultation is required for 883-qualified devices. It does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status.

데이터 검증일: 2026-11-10 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

AD9100JD datasheet AD9100JD pinout AD9100JD datasheet pdf AD9100JD package AD9100JD equivalent AD9100JD replacement AD9100JD drop-in alternative AD9100JD acquisition time AD9100JD aperture jitter AD9100JD tracking bandwidth Analog Devices AD9100JD AD9100JD price AD9100JD lead time AD9100JD track-and-hold amplifier AD9100JD ADC front end

관련 부품 & 용어

Analog Devices AD9100 AD9100JD track-and-hold amplifier sample-and-hold amplifier monolithic track-and-hold high-speed amplifier analog-to-digital converter signal acquisition complementary bipolar process semiconductor acquisition time aperture jitter tracking bandwidth hold-mode distortion feedthrough rejection capacitive load 20-lead side-brazed skinny DIP ceramic DIP package surface connection 30 MSPS 250 MHz 13 ns less than 1 ps 100 pF
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기