AD977BR - 16-Bit 100 kSPS Serial ADC | Analog Devices
부품 번호: AD977BR ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
AD977BR 개요
An ADC is a data-acquisition semiconductor that converts an analog voltage into a digital code for measurement, control, instrumentation, and signal-processing systems. The AD977 belongs to the successive-approximation ADC family, also called a SAR ADC. Compared with flash and pipeline converters, a SAR ADC generally uses sequential internal comparisons, making this device suitable for moderate-speed precision acquisition where output resolution, serial communication, and low power are more important than very high conversion throughput.
The AD977BR provides a 16-bit conversion result at 100 kSPS from a single 5 V supply. Its input architecture supports unipolar ranges of 0 V to 5 V and 0 V to 4 V, plus bipolar ranges of ±5 V and ±3.3 V. The verified sources also identify external-reference and power-down options, internal-reference capability, and industrial-temperature packaging. These features allow the same converter family to address sensor interfaces, process-control measurements, laboratory acquisition, and industrial diagnostic systems.
The switched-capper architecture is factory calibrated, as stated in the Analog Devices datasheet description. Sampling and conversion behavior must be coordinated with the serial interface and external analog network. The AD977BR uses serial I/O rather than a parallel data bus, reducing package pin count and PCB routing requirements while requiring compatible firmware or control logic. The AD977A member provides a higher 200 kSPS rate, whereas the AD977BR is the 100 kSPS version.
Typical applications include industrial process monitoring, sensor signal acquisition, medical instrumentation, laboratory measurement, communications equipment, and embedded data-acquisition systems. A system designer should verify the exact input range, reference configuration, timing, electrical limits, and pin-level requirements against the manufacturer datasheet before layout or firmware release.
The most important design consideration is preserving analog signal integrity while supporting the serial interface. Keep the analog input and reference paths short, use suitable bypass and filtering components, and account for source impedance during acquisition. The verified data does not provide all timing, accuracy, temperature, and reference-load details, so those values should be obtained from the official AD977/AD977A datasheet.
This page consolidates the verified manufacturer and distributor information, separates confirmed AD977BR characteristics from unknown parameters, and provides application guidance without treating unverified values as specifications.
드롭인 대체품: AD977BR — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
이 제품에는 사용 가능한 드롭인 대체품이 없습니다.
대체품 요청AD977BR 최대 정격 & 전기적 특성
| Converter Type | Successive-approximation ADC |
| 분해능 | 16 bit |
| Throughput Rate | 100 kSPS |
| Input Count | 1 input |
| 공급 전압 | 5 V single supply |
| Unipolar Input Range | 0 V to 5 V and 0 V to 4 V |
| Bipolar Input Range | ±5 V and ±3.3 V |
| 인터페이스 | Serial I/O |
| Internal Reference | 2.5 V internal reference |
| External Reference Option | Available; exact ratings not provided |
| Power Dissipation | 100 mW maximum |
| Power-Down Mode | Available |
| Architecture | Factory-calibrated switched-capacitor ADC |
| 패키지 | 20-lead SOIC |
| Package Code | SOP |
| Terminal Form | Gull wing |
| 실장 유형 | Surface mount |
| Temperature Grade | Industrial |
| AD977A Related Throughput | 200 kSPS for AD977A; AD977BR is 100 kSPS |
AD977BR sop 핀 구성 가이드
AD977BR(sop 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: AD977BR.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
AD977BR 적합 용도: 6 애플리케이션s: Industrial Process Measurement, Sensor Signal Acquisition, Medical Instrumentation, Laboratory Data Acquisition, Communications and RF Monitoring, Embedded Control Systems.
Industrial Process Measurement
The AD977BR fits industrial process-monitoring channels that require a 16-bit measurement at 100 kSPS while operating from one 5 V supply. Its serial I/O can connect to a microcontroller or controller without a wide parallel data bus, and the verified unipolar ranges of 0–5 V and 0–4 V support suitable sensor-conditioning outputs. Use the converter acquisition sequence and external filtering to preserve accuracy; the supplied data does not provide detailed timing or accuracy limits, so final channel settling must be verified against the manufacturer datasheet.
추천
Sensor Signal Acquisition
For pressure, temperature, position, or current-sensor interfaces, the AD977BR provides a 16-bit SAR conversion at 100 kSPS with selectable unipolar or bipolar input ranges. The 0–5 V unipolar range is useful for many sensor front ends, while ±3.3 V and ±5 V options can match bipolar sensor outputs. The analog input network, reference arrangement, sampling capacitor, and source impedance must be designed together because the verified snippets do not specify acquisition-time or drive-current details.
추천
Medical Instrumentation
The AD977BR can serve as the acquisition converter in medical or diagnostic instruments where 16-bit numerical resolution and moderate sampling speed are required. A 100 kSPS rate is appropriate for many pressure, flow, or physiological monitoring signals when the system bandwidth is well below the Nyquist limit. The verified data does not state medical certification, isolation, leakage-current, or safety ratings, so medical use requires separate system qualification and compliance review.
추천
Laboratory Data Acquisition
The AD977BR is suited to laboratory measurement front ends that need a 16-bit ADC result and serial data transfer at up to 100 kSPS. Its single 5 V supply simplifies system power planning, while the 20-lead SOIC package supports conventional PCB assembly. A laboratory design should account for analog grounding, shielded interconnects, reference stability, and input filtering. Confirm acquisition settling, noise, linearity, and reference specifications from the official datasheet because those values are not included in the supplied search snippets.
추천
Communications and RF Monitoring
In communications or RF monitoring equipment, the AD977BR can digitize slow or moderate-bandwidth envelope and monitor signals when 100 kSPS is adequate. The 16-bit resolution can preserve small amplitude variations after suitable conditioning, and the serial interface helps reduce board-space requirements. It is not a substitute for a high-speed RF sampler when the monitored waveform contains significant content above 50 kHz; filter and anti-alias design must be based on the actual signal bandwidth.
추천
Embedded Control Systems
The AD977BR works as a precision measurement front end for embedded controllers because it combines a 100 kSPS conversion rate with serial I/O. A microcontroller can issue conversion control signals, receive the digital result, and process the measurement without a 16-wire parallel bus. Power-down mode can reduce consumption during inactive intervals, although shutdown current and wake timing are not stated in the verified snippets. Firmware and hardware should therefore follow the manufacturer timing diagram.
추천
추천 제품 요약
엔지니어링 참조 데이터: AD977BR — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | AD977ARZ | AD977ABRZ | AD976BR |
|---|---|---|---|---|
| Package | 20-lead SOIC | 20-lead SOIC; package stated in cross-reference listing | 20-lead SOIC; package stated in comparison listing | 20-lead SOIC; package inferred only from family search result |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
주요 차별점
- 100 kSPS throughput (vs AD977ABRZ)
- Single 5 V operation (vs AD977ARZ)
- Serial I/O integration (vs AD976BR)
- Multiple input-range choices (vs AD977ABRZ)
설계 노트
Place the analog input, reference, and converter supply bypass components close to their associated pins. Keep the high-impedance analog input route short and separate from serial clock and data traces. The verified snippets do not specify exact layout values, so use the manufacturer application guidance and datasheet recommendations for capacitor selection, grounding, and exposed routing requirements.
Treat the serial interface as a controlled digital timing problem. Confirm clock polarity, conversion timing, data validity, and power-up behavior from the AD977/AD977A datasheet before writing firmware. Provide adequate pull-up or pull-down termination only where the interface specification calls for it; arbitrary resistor values can change edge behavior or create unwanted current.
The verified listing states a single 5 V supply and 100 mW maximum power dissipation, but it does not provide operating supply current. Before estimating system power, obtain the ADC supply-current and power-up specifications from the manufacturer datasheet and include regulator tolerance, analog reference current, external circuitry, and power-down behavior in the budget.
Do not treat a related-family MPN as a confirmed drop-in replacement solely because it appears in a cross-reference search result. AD977ARZ and AD977ABRZ are named in comparison pages, but the supplied data does not verify every pin, timing, electrical, and temperature requirement. Compare the official datasheets and confirm the package suffix and interface behavior before substitution.
규정 준수 정보
The supplied verified search results do not explicitly provide compliance declarations for AD977BR. Do not infer RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-mineral status from the product listing alone.
