ADF4356BCPZ-RL7 - 6.8 GHz PLL Synthesizer | Analog Devices
부품 번호: ADF4356BCPZ-RL7 ✓ 활성ADF4356BCPZ-RL7 개요
A frequency synthesizer is a clock-and-timing IC that locks an internal voltage-controlled oscillator to an external reference frequency. The ADF4356 belongs to the phase-locked-loop family, where the phase-locked-loop synthesizer hierarchy supports stable RF carrier generation for integer-N channels or fine fractional-N channel spacing. The device requires an external reference, loop filter, and passive loop-filter components to complete the feedback network.
Key features include programmable fractional-N and integer-N operation, an integrated VCO, output division by 1, 2, 4, 8, 16, 32, or 64, hardware and software power-down modes, and pin-programmable or software-controlled RF output muting. Analog and digital power rails operate from 3.15 V to 3.45 V, while the charge pump and VCO supply operate from 4.75 V to 5.25 V. These separate supply domains support careful partitioning of noisy, sensitive, and digital circuitry.
The synthesizer architecture allows the loop bandwidth, reference path, channel spacing, and output frequency to be configured through its serial programming interface. Its RF output stages can generate fundamental VCO frequencies or divided outputs as low as 53.125 MHz. The external loop filter remains a critical analog network because it converts phase-detector current into the VCO control voltage and directly influences phase noise, reference spur performance, lock time, and channel-to-channel isolation.
Typical applications include 6 GHz wireless infrastructure, microwave backhaul, radar test equipment, satellite and microwave communications, RF instrumentation, and local-oscillator generation for mixers or upconverters. The 6.8 GHz ceiling is particularly useful for short-wavelength wireless systems operating near the lower portion of the 6 GHz band. For lower-frequency equipment, the output divider reduces the fundamental oscillator frequency without requiring a second synthesizer.
PCB implementation should preserve the integrity of the reference, charge-pump, loop-filter, and RF output paths. Place the loop-filter components close to their associated pins, keep the exposed thermal pad connected to a low-impedance ground plane, and follow the manufacturer reference design for component values and trace geometry. Account for the added Register 13 when moving from ADF4355-based firmware to the ADF4356 initialization sequence.
This page combines manufacturer specifications, verified commercial availability, replacement analysis, and application-specific engineering guidance to support component selection and board bring-up. It also distinguishes direct physical replacements from related synthesizers whose frequency range, control interface, or firmware requirements make them less suitable for a drop-in substitution.
드롭인 대체품: ADF4356BCPZ-RL7 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 제품에는 사용 가능한 드롭인 대체품이 없습니다.
대체품 요청ADF4356BCPZ-RL7 사양
| Product Type | Fractional-N and integer-N PLL frequency synthesizer |
| Integrated VCO Fundamental Frequency Range | 3400 MHz to 6800 MHz |
| Maximum RF Output Frequency | 6800 MHz |
| Minimum Divided RF Output Frequency | 53.125 MHz |
| Output Divider Ratios | 1, 2, 4, 8, 16, 32, or 64 |
| Analog and Digital Supply Voltage Range | 3.15 V to 3.45 V |
| Charge Pump and VCO Supply Voltage Range | 4.75 V to 5.25 V |
| Number of Channels | 1 |
| 패키지 | 32-lead WFQFN exposed-pad package |
| 실장 유형 | Surface mount |
| Power-Down Modes | Hardware and software |
| RF Output Muting | Pin-programmable and software-programmable |
| Phase-Locked-Loop Type | Fractional-N or integer-N |
ADF4356BCPZ-RL7 32-lead wfqfn exposed-pad package 핀 구성 가이드
ADF4356BCPZ-RL7(32-lead wfqfn exposed-pad package 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: ADF4356BCPZ-RL7.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
ADF4356BCPZ-RL7 적합 용도: 6 애플리케이션s: 6 GHz Wireless Infrastructure, Microwave Backhaul Local Oscillator, Radar and RF Test Equipment, Satellite and Microwave Communications, RF Instrumentation, Low-Frequency IF and Divider Output.
6 GHz Wireless Infrastructure
The ADF4356BCPZ-RL7 is well matched to 6 GHz wireless local-oscillator and carrier-generation requirements because its integrated VCO operates from 3400 MHz to 6800 MHz. The synthesizer can support fractional-N channel spacing while also operating in integer-N mode for less demanding frequency plans. A typical design feeds a clean reference into the phase-locked loop, filters the charge-pump current, and routes the resulting RF output toward a mixer or transmit chain. The 6.8 GHz ceiling covers the lower portion of the 6 GHz band, but phase noise and adjacent-channel rejection remain functions of reference quality, loop bandwidth, and the external filter.
추천
Microwave Backhaul Local Oscillator
The ADF4356BCPZ-RL7 can generate a programmable local oscillator for microwave backhaul receivers and transmitters requiring frequencies below 6.8 GHz. Its output dividers reduce the fundamental VCO signal into six lower-frequency ratios, allowing one synthesizer to cover receiver and transmit-frequency plans. In the circuit, the ADF4356 locks to an external reference and the loop filter controls phase noise and lock behavior. Designers should place the RF output path and loop filter away from switching supplies and digital return currents, then verify reference spur rejection under the final reference frequency and channel spacing.
추천
Radar and RF Test Equipment
The ADF4356BCPZ-RL7 supports programmable RF test sources covering 53.125 MHz to 6800 MHz through its integrated VCO and output-divider options. This flexibility lets laboratory equipment move between low-frequency IF tests and microwave signal-generation tests without relying on several separate oscillators. The synthesizer is used with an external reference and loop filter, while its programmable register interface supports automated frequency changes. For measurement-grade performance, characterize phase noise, reference spurs, and settling time with the intended reference and firmware configuration rather than relying on nominal frequency accuracy alone.
추천
Satellite and Microwave Communications
The ADF4356BCPZ-RL7 is applicable to microwave communication subsystems that need a programmable local oscillator with fractional channel spacing. Its maximum VCO frequency of 6800 MHz permits direct synthesis near the upper range of the device specification, while the divider chain supports lower-frequency intermediate signals. The circuit architecture requires a stable reference, charge-pump loop filter, and RF output network. Engineers should account for temperature drift, reference multiplication ratio, and loop-filter component tolerance because these factors directly influence frequency stability and spur performance in the communication channel.
추천
RF Instrumentation
The ADF4356BCPZ-RL7 can serve as the RF source in instrumentation covering wide frequency ranges when paired with a suitable reference and output divider. Programmable fractional-N operation allows the instrument to select exact test frequencies, while integer-N operation can simplify configurations where very fine channel spacing is unnecessary. The synthesizer should be mounted on a controlled-impedance RF layout with short output paths and solid return-plane continuity. Calibration must include the attenuation, frequency-dependent loss, and phase response of the complete signal path because the synthesizer itself is only one contributor to traceable measurement accuracy.
추천
Low-Frequency IF and Divider Output
The ADF4356BCPZ-RL7 can produce divided outputs down to 53.125 MHz by applying the available division ratios to its 3400 MHz to 6800 MHz VCO signal. This capability supports IF-generation and local-oscillator roles where a conventional high-frequency oscillator would be unnecessary. The output divider reduces RF frequency while the phase-locked loop maintains phase coherence with the reference. Designers should select the lowest divider that meets the required frequency, preserve adequate output drive, and verify that divider harmonics do not interfere with sensitive receiver or analyzer stages.
추천
추천 제품 요약
엔지니어링 참조 데이터: ADF4356BCPZ-RL7 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 |
|---|---|
| Package | 32-lead WFQFN exposed-pad package |
| Brand | Analog Devices |
| Fundamental VCO Frequency Range | 3400 MHz to 6800 MHz |
| Maximum RF Output Frequency | 6800 MHz |
| Minimum Divided RF Output Frequency | 53.125 MHz |
| Output Divider Ratios | 1, 2, 4, 8, 16, 32, or 64 |
| Analog and Digital Supply Voltage | 3.15 V to 3.45 V |
| Charge Pump and VCO Supply Voltage | 4.75 V to 5.25 V |
| PLL Architecture | Fractional-N or integer-N |
| Power-Down Modes | Hardware and software |
주요 차별점
- Higher integrated-VCO operating ceiling than the ADF4355 family (vs ADF4355BCPZ-RL7)
- Broad programmable output division for mixed-frequency designs (vs ADF4355BCPZ-RL7)
- Exact reel-configured ordering option (vs ADF4356BCPZ)
설계 노트
Route the charge-pump output and loop-filter components directly between their associated pins and ground reference without long shared traces. Keep the external filter away from RF output and switching-node copper where possible. The filter converts charge-pump current into the VCO tuning voltage, so even modest leakage or added capacitance can change loop dynamics, phase noise, and lock behavior. Use the Analog Devices ADF4356 reference layout to preserve component values, grounding, and isolation.
Use separate, well-decoupled connections for the 3.15 V to 3.45 V analog and digital supplies and the 4.75 V to 5.25 V charge-pump and VCO supply. Place local high-frequency bypass capacitors at the supply pins and keep supply-return paths continuous through the exposed ground pad. Because the VCO and charge pump are sensitive to supply disturbance, regulator placement and return-current routing can influence phase noise and reference-spur performance even when the nominal supply voltages are correct.
Do not treat an ADF4355 device as an unconditional software-compatible replacement for the ADF4356. Analog Devices application note AN-1445 identifies an initialization change involving Register 13 and describes removal or adaptation of the R SET resistor on Pin 22. Review the complete register sequence, R SET configuration, reference ratio, loop filter, and target output frequency before reusing an existing board or firmware. A physical package fit alone does not establish functional equivalence.
Design the RF output path as a controlled-impedance structure with short connections and a continuous ground reference. Avoid placing test pads, long branch runs, or unrelated digital traces near the RF outputs. When using an output divider, verify the selected ratio produces the required frequency and check that divider harmonics remain below the sensitivity of the downstream receiver. Final spur and isolation measurements should use the complete board because package and enclosure details can materially affect RF performance.
규정 준수 정보
Compliance declarations require confirmation from the current manufacturer product documentation or a declaration associated with the exact ordering code.