ADM207EAN - 5/3 RS-232 Transceiver, 230kbps | Analog Devices
부품 번호: ADM207EAN ✓ 활성ADM207EAN 개요
An RS-232 transceiver is an interface IC that translates between single-ended logic-level signals and the bipolar voltage levels used by RS-232 equipment. Within the broader electronics hierarchy, it belongs to the interface-controller family and connects digital systems to communication ports. A multi-driver and multi-receiver device can consolidate several serial channels onto one printed circuit board while reducing the number of separate line-driver packages.
The ADM207EAN provides five drivers and three receivers, operates at data rates up to 230 kbps, and conforms to the EIA-232E and CCITT V.28 specifications. These characteristics make it suitable for industrial data acquisition, test equipment, point-of-sale terminals, computer peripherals, and embedded control systems. The three receivers are useful for acknowledging handshakes, receiving status signals, or supporting a multidrop arrangement in which several line-driver outputs feed one receiver.
Its integrated protection reduces the need for separate TransZorb devices on exposed serial lines. The documented immunity targets include 8 kV contact discharge, 15 kV air-gap discharge, 15 kV human-body-model ESD protection, and fast-transient-burst immunity under IEC 1000-4-4. Low EMI emissions under EN 55022 are also listed, helping simplify compliance planning for equipment connected to external RS-232 cables.
Typical installations include multi-port industrial controllers, laboratory interfaces, serial concentrators, and legacy peripheral equipment. In these systems, each TTL/CMOS-side channel connects to a host processor, while the corresponding driver output or receiver input connects to the external RS-232 port. The 230 kbps maximum rate supports substantially faster operation than the traditional 20 kbps RS-232 limit, although cable length, capacitance, grounding, and driver slew behavior must still be considered.
A critical layout practice is to keep the transceiver close to the connector and route protected cable-side traces directly to the appropriate pins. Place bypass capacitors near the supply pins, maintain a low-impedance ground reference between the interface and the system, and avoid sharing narrow return paths with sensitive analog signals. The external RS-232 connector should also satisfy applicable product-level ESD and EMC requirements.
This product page combines the manufacturer’s device specifications, interface-family positioning, application guidance, pin and package constraints, and strict drop-in comparison criteria. It also highlights the practical limitations of package variants and functionally similar transceivers so engineers can distinguish a true board-level replacement from a merely similar RS-232 device.
드롭인 대체품: ADM207EAN — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ADM207EAN (동일 폼 팩터 및 풋프린트) — 차이점: Maximum Data Rate, Product Type.
ADM207EANZ
✅ 드롭인가격 문의
데이터시트 보기 →ADM207AN
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →ADM207EAN 사양
| Driver Count | 5 |
| Receiver Count | 3 |
| Maximum Data Rate | 230 kbps |
| Interface Standard | RS-232 |
| ESD Protection | ±15 kV |
| Contact Discharge | 8 kV |
| Air-Gap Discharge | 15 kV |
| ESD Test Method | IEC 801.2, 15 kV human body model |
| Fast Transient Burst Immunity | IEC 1000-4-4 |
| EMI Emissions Standard | EN 55022 |
| RS-232 Compliance | EIA-232E and CCITT V.28 |
| 패키지 | 24-pin PDIP |
| Package Type | Through-hole PDIP |
ADM207EAN through-hole pdip 핀 구성 가이드
ADM207EAN(through-hole pdip 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: ADM207EAN.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
ADM207EAN 적합 용도: 6 애플리케이션s: Industrial Multi-Port Serial Controller, RS-232 Test and Measurement Equipment, Point-of-Sale and Retail Equipment, Computer Peripherals and Legacy Equipment, Embedded Communications Concentrator, Instrumentation and Data-Acquisition Systems.
Industrial Multi-Port Serial Controller
The ADM207EAN fits industrial controllers that must connect several peripheral buses through one RS-232 interface. Five driver outputs can operate control, status, or handshake channels, while three receiver inputs can accept acknowledgements, remote commands, or fault signals. Its maximum rate of 230 kbps supports faster legacy serial equipment than the traditional 20 kbps RS-232 rate. The integrated ±15 kV ESD protection and IEC 1000-4-4 burst-immunity target improve robustness at connector boundaries, but designers must still provide a controlled ground reference and verify cable length, capacitance, and isolation in the final enclosure.
추천
RS-232 Test and Measurement Equipment
The ADM207EAN is useful in laboratory instruments that expose multiple RS-232 ports for legacy instruments, fixtures, and service consoles. The five-driver and three-receiver arrangement supports several independently controlled channels without requiring one transceiver package per signal. Operation up to 230 kbps accommodates equipment using faster V.28-class links while retaining compatibility with EIA-232E expectations. Because test systems often route long cables through crowded benches, the device’s 15 kV air-gap and human-body-model ESD ratings provide useful protection margin, although connector selection, grounding, and external surge requirements remain part of the product design.
추천
Point-of-Sale and Retail Equipment
Retail terminals can use the ADM207EAN to consolidate serial links to scales, printers, customer displays, and magnetic-stripe peripherals. Five transmit channels provide flexibility for command and status paths, while three receive channels can support device acknowledgements or shared responses. The 230 kbps maximum data rate accommodates short, shielded serial runs at speeds often unavailable from older RS-232 implementations. Integrated ESD protection is particularly valuable when service personnel connect peripheral cables, while documented EN 55022 emissions behavior and fast-transient-burst immunity help structure a robust interface. Firmware must still avoid simultaneous driver conflicts on shared bus segments.
추천
Computer Peripherals and Legacy Equipment
The ADM207EAN is appropriate for peripheral controllers that need to support several legacy RS-232 functions while retaining a modern TTL/CMOS control section. A printer interface, modem control channel, and auxiliary status link can share one package when the board requires five outputs and only three inputs. The 24-pin PDIP format is also convenient for through-hole industrial add-on cards and legacy motherboard designs. At rates up to 230 kbps, the device supports fast short-distance communication, but cable capacitance and timing margin must be checked against the selected data rate. The logic-side supply requirements and shutdown-control behavior should be confirmed from the manufacturer datasheet during schematic design.
추천
Embedded Communications Concentrator
The ADM207EAN can form the RS-232 side of an embedded communications concentrator that gathers data from several local devices. Five driver outputs may carry independent commands or broadcasts, and the three receiver inputs can collect status from the most active nodes. Its 230 kbps capability makes it practical for high-speed short-distance links in supervisory control and data-acquisition cabinets. The integrated ESD protection reduces connector exposure risk, while IEC 1000-4-4 burst immunity is relevant to electrically noisy industrial environments. Engineers should avoid simultaneous active outputs on the same bus, use the specified transceiver power strategy, and validate grounding with the complete cable and enclosure configuration.
추천
Instrumentation and Data-Acquisition Systems
The ADM207EAN is useful in data-acquisition front ends that retain RS-232 for older sensors, controllers, and service interfaces. Multiple transmitter channels can carry commands to separate devices, and three receiver channels can collect asynchronous acknowledgements or status information. The 230 kbps rate supports compact, short-distance links, but designers should not confuse the IC’s maximum signaling rate with guaranteed performance over every cable length. The device’s ±15 kV ESD protection, 8 kV contact rating, and low-emissions target improve interface robustness in laboratory and industrial installations. Signal conditioning, galvanic isolation, and surge protection should be added when the connected cable leaves the controlled enclosure.
추천
추천 제품 요약
엔지니어링 참조 데이터: ADM207EAN — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 |
|---|---|
| Driver Count | 5 |
| Receiver Count | 3 |
| Maximum Data Rate | 230 kbps |
| Interface Standard | RS-232 |
| Package | 24-pin PDIP |
| Brand | Analog Devices |
| ESD Protection | ±15 kV |
| Contact Discharge | 8 kV |
| Air-Gap Discharge | 15 kV |
| Fast Transient Burst | IEC 1000-4-4 |
| EMI Emissions | EN 55022 |
| Specification Conformance | EIA-232E and CCITT V.28 |
주요 차별점
- Higher transmitter-channel count (vs ADM202EAN)
- Different receive-channel balance (vs ADM208EAN)
- Integrated multi-line ESD protection (vs MC1489NG4)
설계 노트
Place the ADM207EAN close to the RS-232 connector and route cable-side driver and receiver traces directly to their corresponding pins. Keep the logic-side traces physically separated from these lines to reduce coupling into sensitive control circuitry. Preserve the package’s pin-one orientation in the PCB footprint and verify the pin-description table in the manufacturer datasheet before releasing artwork.
Do not allow two enabled ADM207EAN driver outputs to drive the same RS-232 node simultaneously. Their opposing outputs can create excessive current, unpredictable voltage levels, and unnecessary EMI. Assign driver directions in firmware or hardware so only one transmitter is active at a time, especially in multidrop arrangements using the three receiver inputs.
Return the RS-232 signal reference through a low-impedance ground path rather than relying on the cable shield as the sole return conductor. Use the connector shell and shield according to the product’s grounding strategy, and keep switching supplies and high-current return paths away from the logic ground reference. Validate radiated and conducted emissions at the completed product level because IC-level EN 55022 behavior does not replace enclosure and cable testing.
Treat 230 kbps as a maximum device capability, not a blanket guarantee for every cable run. RS-232 timing margin depends on line capacitance, cable length, driver loading, receiver threshold behavior, and grounding. For long or high-capacitance cables, reduce the baud rate, add suitable line conditioning, or choose a communication standard designed for longer distances and multipoint networks.
규정 준수 정보
The documented interface qualifications include EIA-232E, CCITT V.28, IEC 801.2 human-body-model ESD testing, IEC 1000-4-4 fast-transient-burst immunity, and EN 55022 EMI-emissions performance. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are not stated in the product information.