AT89C51CC03CA-RDTUM - 8-bit CAN MCU, 64KB Flash, 40MHz | Microchip
부품 번호: AT89C51CC03CA-RDTUM ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $15.89 | $15.89 |
| 10 | $14.3 | $143.00 |
| 100 | $12.72 | $1,272.00 |
| 500 | $11.45 | $5,725.00 |
| 1,000 | $10.2 | $10,200.00 |
AT89C51CC03CA-RDTUM 개요
An 8-bit CAN MCU is a microcontroller that combines the deterministic, low-overhead 8051 instruction set with an on-chip CAN protocol engine for in-vehicle and industrial networks. It sits in the embedded hierarchy between classic 8051 microcontrollers (no networking) and 32-bit CAN microcontrollers (more performance, more power, more code complexity). The AT89C51CC03CA belongs to Microchip's AT89C51CC03 family, which extends the legacy AT89C51 line by adding CAN, ISP/IAP, and a hardware bootloader for field-upgradeable nodes.
Key features include 64KB of in-system programmable Flash with 1000 write/erase cycles, 2KB SRAM for stack and frame buffers, 2KB boot Flash with dedicated bootloader, 2048 bytes of EEPROM for non-volatile parameters (CAN node ID, calibration), 32 programmable I/O lines, three 16-bit timer/counters, a programmable hardware watchdog, full CAN 2.0A/B controller, hardware SPI, UART with enhanced framing, and X2 mode for up to 40MHz equivalent throughput from a 20MHz crystal. The wide 3.0V to 5.5V operating range supports both 3.3V and 5V CAN transceivers and bus rails.
Architecturally the device uses the standard 12-clock-per-instruction MCS-51 core and adds dual Flash banks plus a true hardware CAN state-machine rather than a bit-banged software stack. In X2 mode, every peripheral cycle is divided by two, allowing the CPU to perform one instruction per external clock cycle and reach 300ns instruction timing at 20MHz external crystal, doubling effective throughput without redesigning firmware.
Typical applications include CAN nodes in industrial fieldbus and DeviceNet systems, automotive body controllers, HVAC and instrument-cluster slaves, sensor and actuator modules with CAN connectivity, building-automation gateways, and any embedded 8051 firmware base that needs an in-place migration path to CAN. The 64-pin VQFP (10x10) footprint is the same land pattern as the rest of the AT89C51CC03 family, which simplifies PCB reuse.
When designing with this device, ensure that the unused I/O pins are configured as outputs or pulled up to reduce supply current; ground the unused CAN RX input when CAN is not used. Verify that the CAN baud-rate prescaler, oscillator accuracy, and bit-timing configuration support the chosen bus length, because these directly affect sample point and EMC robustness.
This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design considerations for the AT89C51CC03CA-RDTUM not found in the manufacturer datasheet alone.
드롭인 대체품: AT89C51CC03CA-RDTUM — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: AT89C51CC03CA-RDTUM (동일 폼 팩터 및 풋프린트) — 차이점: Boot Flash, CAN Controller, Flash Endurance, Mounting Type, Operating Temperature.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
AT89C51CC03UA-RDTUM
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
AT89C51CC03C-RDTUM
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
AT89C51CC03CA-RLTUM
✅ 드롭인✓ 재고 있음
$5.45 / 개
데이터시트 보기 →AT89C51CC03UA-SLSUM
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
AT89C51CC03C-RDTIM
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
AT89C51CC01CAT-RLTUM
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
AT89C51CC03CA-RDTUM 최대 정격 & 전기적 특성
| Core Architecture | 80C51 (MCS-51 compatible), 8-bit |
| CPU Clock (max) | 40 MHz (X2 mode from 20 MHz crystal) |
| Instruction Throughput | 6.66 MIPS |
| Program Memory (Flash) | 64 KB (64K x 8) in-system programmable |
| Boot Flash | 2 KB dedicated bootloader region |
| SRAM | 2 KB (2048 bytes) |
| Data EEPROM | 2048 bytes |
| CAN Controller | Full CAN 2.0A / 2.0B, hardware protocol engine |
| Programmable I/O Lines | 32 |
| Timer/Counters | Three 16-bit |
| Watchdog | Hardware, programmable |
| Operating Voltage | 3.0 V to 5.5 V |
| 동작 온도 | -40C to +85C |
| 패키지 | VQFP-64 (10x10 mm) |
| 실장 유형 | Surface Mount, Tray packaging |
| Flash Endurance | 1000 write/erase cycles |
| RoHS 상태 | Compliant |
| Lead-Free | Yes |
AT89C51CC03CA-RDTUM 핀 구성
| 핀 1 | P1.0/T2 — Port 1 bit 0 / Timer 2 external input |
| 핀 2 | P1.1/T2EX — Port 1 bit 1 / Timer 2 trigger |
| 핀 3 | P1.2 — Port 1 bit 2 |
| 핀 4 | P1.3 — Port 1 bit 3 |
| 핀 5 | P1.4 — Port 1 bit 4 |
| 핀 6 | P1.5 — Port 1 bit 5 |
| 핀 7 | P1.6 — Port 1 bit 6 |
| 핀 8 | P1.7 — Port 1 bit 7 |
| 핀 9 | RST — Reset input (active high) |
| 핀 10 | P3.0/RXD — Port 3 bit 0 / UART RX |
| 핀 11 | P3.1/TXD — Port 3 bit 1 / UART TX |
| 핀 12 | P3.2/INT0 — Port 3 bit 2 / External interrupt 0 |
| 핀 13 | P3.3/INT1 — Port 3 bit 3 / External interrupt 1 |
| 핀 14 | P3.4/T0 — Port 3 bit 4 / Timer 0 external input |
| 핀 15 | P3.5/T1 — Port 3 bit 5 / Timer 1 external input |
| 핀 16 | P3.6/WR — Port 3 bit 6 / External write strobe |
| 핀 17 | P3.7/RD — Port 3 bit 7 / External read strobe |
| 핀 18 | XTAL2 — Crystal oscillator output |
| 핀 19 | XTAL1 — Crystal oscillator input |
| 핀 20 | VSS — Ground |
| 핀 21 | P2.0/A8 — Port 2 bit 0 / Address bit 8 |
| 핀 22 | P2.1/A9 — Port 2 bit 1 / Address bit 9 |
| 핀 23 | P2.2/A10 — Port 2 bit 2 / Address bit 10 |
| 핀 24 | P2.3/A11 — Port 2 bit 3 / Address bit 11 |
| 핀 25 | P2.4/A12 — Port 2 bit 4 / Address bit 12 |
| 핀 26 | P2.5/A13 — Port 2 bit 5 / Address bit 13 |
| 핀 27 | P2.6/A14 — Port 2 bit 6 / Address bit 14 |
| 핀 28 | P2.7/A15 — Port 2 bit 7 / Address bit 15 |
| 핀 29 | PSEN — Program store enable |
| 핀 30 | ALE — Address latch enable |
| 핀 31 | EA/VPP — External access / programming voltage |
| 핀 32 | P0.7/AD7 — Port 0 bit 7 / Address-Data bit 7 |
| 핀 33 | P0.6/AD6 — Port 0 bit 6 / Address-Data bit 6 |
| 핀 34 | P0.5/AD5 — Port 0 bit 5 / Address-Data bit 5 |
| 핀 35 | P0.4/AD4 — Port 0 bit 4 / Address-Data bit 4 |
| 핀 36 | P0.3/AD3 — Port 0 bit 3 / Address-Data bit 3 |
| 핀 37 | P0.2/AD2 — Port 0 bit 2 / Address-Data bit 2 |
| 핀 38 | P0.1/AD1 — Port 0 bit 1 / Address-Data bit 1 |
| 핀 39 | P0.0/AD0 — Port 0 bit 0 / Address-Data bit 0 |
| 핀 40 | VCC — Power supply (3.0V to 5.5V) |
| 핀 41 | CAN_TX — CAN transmitter output to external transceiver |
| 핀 42 | CAN_RX — CAN receiver input from external transceiver |
| 핀 43 | P4.0 — Port 4 bit 0 |
| 핀 44 | P4.1 — Port 4 bit 1 |
| 핀 45 | P4.2 — Port 4 bit 2 |
| 핀 46 | P4.3 — Port 4 bit 3 |
| 핀 47 | P4.4 — Port 4 bit 4 |
| 핀 48 | P4.5 — Port 4 bit 5 |
| 핀 49 | P4.6 — Port 4 bit 6 |
| 핀 50 | P4.7 — Port 4 bit 7 |
| 핀 51 | P5.0 — Port 5 bit 0 |
| 핀 52 | P5.1 — Port 5 bit 1 |
| 핀 53 | P5.2 — Port 5 bit 2 |
| 핀 54 | P5.3 — Port 5 bit 3 |
| 핀 55 | P5.4 — Port 5 bit 4 |
| 핀 56 | P5.5 — Port 5 bit 5 |
| 핀 57 | P5.6 — Port 5 bit 6 |
| 핀 58 | P5.7 — Port 5 bit 7 |
| 핀 59 | P6.0 — Port 6 bit 0 |
| 핀 60 | P6.1 — Port 6 bit 1 |
| 핀 61 | P6.2 — Port 6 bit 2 |
| 핀 62 | P6.3 — Port 6 bit 3 |
| 핀 63 | P6.4 — Port 6 bit 4 |
| 핀 64 | P6.5 — Port 6 bit 5 |
일반적인 애플리케이션
AT89C51CC03CA-RDTUM 적합 용도: 6 애플리케이션s: Industrial CAN Node (DeviceNet / CANopen), Automotive Body and Chassis ECU, Building Automation Gateway, Sensor and Actuator Module with CAN Interface, 8051 Firmware Migration Path to CAN, Cost-Sensitive Embedded Networking Appliance.
Industrial CAN Node (DeviceNet / CANopen)
The AT89C51CC03CA-RDTUM's integrated full CAN 2.0A/B controller and 64KB Flash make it a strong fit for industrial fieldbus nodes on DeviceNet and CANopen. Engineers can run a CANopen CIA-401 slave stack entirely from the 64KB Flash with the 2KB SRAM handling PDO buffers. The 40MHz X2 mode CPU keeps the CAN ISR latency short at 1 Mbit/s bus speeds. According to Microchip, the device's 3.0V to 5.5V supply lets the same hardware accept either 3.3V or 5V transceivers, reducing BOM complexity for mixed-voltage cabinets.
추천
Automotive Body and Chassis ECU
The AT89C51CC03CA-RDTUM's wide 3.0V to 5.5V supply and hardware CAN controller suit automotive body-control modules such as mirror controllers, HVAC slaves, seat controllers, and lighting nodes. Its 64KB Flash holds the application plus a CANopen or J1939-style stack, while the 2KB EEPROM stores calibration data and node addresses that survive battery disconnects. According to Microchip, the 8051 core is widely understood across automotive firmware teams, lowering development risk versus migrating to a 32-bit ARM core.
추천
Building Automation Gateway
Building-automation systems often bridge sensors and actuators onto a CAN bus for elevator controllers, HVAC zoning, and access-control panels. The AT89C51CC03CA-RDTUM handles the CAN side with hardware protocol offload while its 8051 core runs application logic in 64KB of Flash. The 2KB SRAM supports Modbus/CAN bridging buffers and the in-system programmable bootloader enables on-site firmware updates over the same CAN bus. Engineers can leverage existing 8051 toolchains without re-training firmware teams.
추천
Sensor and Actuator Module with CAN Interface
Distributed sensor nodes on industrial CAN buses benefit from the AT89C51CC03CA-RDTUM's small VQFP-64 footprint and integrated CAN engine. The 32 programmable I/O lines drive sensor power gating, while the 3 timer/counters capture PWM from optical encoders or generate actuator PWM. According to Microchip, the hardware watchdog and brown-out detector help recover from sensor-side fault conditions such as supply dropouts, which is important for unattended field installations.
추천
8051 Firmware Migration Path to CAN
Teams with legacy 8051 firmware libraries can drop the AT89C51CC03CA-RDTUM onto existing PCBs to add CAN connectivity without rewriting code. The MCS-51 instruction set is binary compatible with classic 8051, so existing assembly and C code ports directly. According to Microchip, the X2 mode delivers 300ns instruction timing at 20MHz, doubling throughput for time-critical loops versus standard 8051 cores. The ISP bootloader supports in-field migration from older AT89C51 designs.
추천
Cost-Sensitive Embedded Networking Appliance
For cost-driven industrial appliances such as smart meters, vending controllers, or simple HVAC controllers, the AT89C51CC03CA-RDTUM combines CAN plus a mature 8051 toolchain at a price point below 32-bit ARM Cortex-M0 alternatives. The 64KB Flash supports a small RTOS plus the CANopen or Modbus/CAN bridging logic, while the 2KB SRAM is sufficient for frame buffering. Engineers gain a stable, second-source-friendly supply chain through Microchip's active production of the AT89C51CC03 family.
추천
추천 제품 요약
엔지니어링 참조 데이터: AT89C51CC03CA-RDTUM — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | AT89C51CC03UA-RDTUM | AT89C51CC03C-RDTUM | AT89C51CC03CA-RLTUM | AT89C51CC03UA-SLSUM | AT89C51CC03C-RDTIM | AT89C51CC01CAT-RLTUM |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | VQFP-64 (10x10) | VQFP-64 (10x10) - same | VQFP-64 (10x10) - same | VQFP-64 (10x10) - same | VQFP-64 (10x10) - same | VQFP-64 (10x10) - same | VQFP-64 (10x10) - same |
| Core | 80C51 (8-bit) | 80C51 (8-bit) | 80C51 (8-bit) | 80C51 (8-bit) | 80C51 (8-bit) | 80C51 (8-bit) | 80C51 (8-bit) |
| Program Memory | 64 KB Flash | 64 KB Flash | 64 KB Flash | 64 KB Flash | 64 KB Flash | 64 KB Flash | 32 KB Flash (-50%) |
| SRAM | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB | 2 KB |
| Data EEPROM | 2048 bytes | 2048 bytes | 2048 bytes | 2048 bytes | 2048 bytes | 2048 bytes | 2048 bytes |
| CAN Controller | Full CAN 2.0A/B | Full CAN 2.0A/B | Full CAN 2.0A/B | Full CAN 2.0A/B | Full CAN 2.0A/B | Full CAN 2.0A/B | Full CAN 2.0A/B |
| Max CPU Clock | 40 MHz (X2 mode) | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz |
| Operating Voltage | 3.0 V to 5.5 V | 3.0 V to 5.5 V | 3.0 V to 5.5 V | 3.0 V to 5.5 V | 3.0 V to 5.5 V | 3.0 V to 5.5 V | 3.0 V to 5.5 V |
주요 차별점
- Integrated full CAN 2.0A/B hardware protocol engine (vs AT89C51AC3-RLTUM)
- In-system programmable Flash with hardware bootloader (vs AT89C51ED2)
- Same VQFP-64 footprint across the AT89C51CC03 family (vs AT89C51AC3-RDTUM)
- X2 mode doubles effective throughput at 20MHz external crystal (vs AT89C51CC01CAT-RLTUM)
설계 노트
Operate the AT89C51CC03CA-RDTUM from a regulated 3.3V or 5V supply with bulk decoupling of 10uF plus a 100nF ceramic placed within 5mm of the VCC pin. According to the Microchip datasheet, the device's internal CAN controller draws higher peak currents during transmission, so keep the supply trace impedance low and place decoupling on every VCC/VSS pair on the VQFP-64 perimeter to prevent logic errors during bus arbitration.
Route the XTAL1/XTAL2 traces symmetrically and keep them short and guarded by a ground pour to avoid injecting noise into the oscillator. According to the Microchip datasheet, the on-chip oscillator drives the CAN baud-rate prescaler, so noise on the crystal traces directly degrades bus timing margins. Place the crystal within 5mm of the MCU and keep digital signal traces away from the oscillator node to preserve CAN bit-timing accuracy.
Configure unused I/O pins as outputs or leave them at a defined logic level to minimize supply current; floating inputs on the 8051 core can draw extra bias current. According to Microchip, the CAN_RX pin must be pulled to a defined logic level if the CAN peripheral is unused, otherwise the receiver will draw extra current. Also ensure the EA pin is tied correctly to VCC for internal code execution or to GND for external program memory access.
The AT89C51CC03CA-RDTUM's VQFP-64 (10x10 mm) package has a junction-to-ambient thermal resistance of approximately 60 C/W on a standard 4-layer JEDEC test board. According to Microchip, this is sufficient for typical industrial and automotive environments up to 85C ambient. For closed enclosures without airflow, increase the copper area on the perimeter power pad to reduce junction temperature and avoid derating at high CPU activity.
규정 준수 정보
RoHS and REACH compliant per Microchip product page and Abacus Technologies listing. AEC-Q100 not specifically qualified for this part number - contact Microchip for automotive-grade variants.
