Microchip Technology

AT90CAN128-16MJ - 16MHz AVR CAN MCU 128KB | Microchip

부품 번호: AT90CAN128-16MJ ✗ 단종
64-QFN, 9 x 9 mm Package 16 MHz Speed 128 KB Memory
MOQ: 1 |

AT90CAN128-16MJ 개요

The Microchip Technology AT90CAN128-16MJ is an 8-bit AVR RISC microcontroller with a 16 MHz clock, 128 KB of flash program memory, and integrated CAN controller in a 64-pin QFN package measuring 9 x 9 mm. The device also includes 4 KB of EEPROM, 4 KB of SRAM, 53 general-purpose I/O lines, and 32 general-purpose working registers, making it suitable for compact embedded CAN nodes requiring substantial firmware storage.

A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripheral functions onto one device. The AT90CAN128 belongs to the AVR microcontroller family and combines an embedded control processor with CAN communications, serial interfaces, timers, and GPIO. Its CAN controller supports CAN 2.0A and CAN 2.0B protocols, while its peripheral set allows a single device to manage local control functions and communicate over a robust industrial network.

The AT90CAN128-16MJ provides 128 KB of ISP flash memory for in-system programming, 4 KB of EEPROM for nonvolatile data retention, and 4 KB of SRAM for working memory. Its 53 general-purpose I/O lines support digital inputs and outputs, while four flexible timer/counter blocks provide timing, compare, capture, and PWM functions. Two USARTs, an SPI interface, and a byte-oriented two-wire serial interface expand its connectivity beyond CAN.

The 16 MHz operating frequency gives the AVR core sufficient throughput for protocol handling, control-loop execution, and peripheral management. The -16 speed designation identifies the 16 MHz configuration, while the MJ ordering code identifies the 64-QFN package configuration. Because the device integrates the CAN controller, only an external CAN transceiver is required to connect the MCU logic-level CAN TX and RX signals to a physical bus.

Typical uses include automotive gateway modules, industrial automation controllers, CAN-connected sensors, vehicle diagnostic equipment, building-control nodes, and embedded instrumentation. A compact 9 x 9 mm QFN package supports space-constrained designs, but its fine pitch and exposed pad require careful PCB layout, adequate copper thermal paths, and assembly-process control.

For PCB implementation, use the manufacturer pin-description table to assign every power, ground, programming, clock, communications, and GPIO connection. Place input, output, and decoupling capacitors according to the manufacturer reference design, provide a continuous ground reference beneath the exposed pad, and confirm that the selected transceiver, oscillator, and power architecture meet the system timing and bus requirements.

This page combines the AT90CAN128 family architecture with package-specific guidance, engineering comparisons, sourcing information, and application-oriented design notes. It helps designers evaluate the 16 MHz CAN-capable MCU for embedded industrial, automotive, and control-system designs before completing the board-level schematic and layout review.

드롭인 대체품: AT90CAN128-16MJ — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

이 제품에는 사용 가능한 드롭인 대체품이 없습니다.

대체품 요청

AT90CAN128-16MJ 최대 정격 & 전기적 특성

Microcontroller Family AVR 90CAN
Architecture 8-bit AVR RISC
최대 클록 주파수 16 MHz
Flash Program Memory 128 KB
EEPROM Memory 4 KB
SRAM 4 KB
General-Purpose I/O Lines 53
General-Purpose Working Registers 32
CAN Controller CAN 2.0A and CAN 2.0B
UART Interfaces 2
Timer/Counter Blocks 4
Serial Interface SPI and byte-oriented two-wire serial interface
패키지 64-QFN, 9 x 9 mm
Exposed Pad Yes
실장 유형 Surface mount
Program Memory Type ISP flash

AT90CAN128-16MJ 64-qfn, 9 x 9 mm 핀 구성 가이드

AT90CAN128-16MJ(64-qfn, 9 x 9 mm 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.

AT90CAN128-16MJ의 64-qfn, 9 x 9 mm 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: AT90CAN128-16MJ.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

AT90CAN128-16MJ 적합 용도: 6 애플리케이션s: Automotive CAN Gateway, Industrial Automation Node, CAN-Connected Sensor Controller, Vehicle Diagnostic Interface, Building Control Terminal, Embedded Test and Control Module.

🚗

Automotive CAN Gateway

The AT90CAN128-16MJ fits an automotive gateway that must exchange diagnostic, body, or sensor data between CAN segments while retaining local control logic. Its hardware CAN controller supports CAN 2.0A and CAN 2.0B, while 128 KB of flash provides room for protocol routing, diagnostics, and application firmware. The 64-QFN package reduces board area, although the exposed pad and fine-pitch routing require careful layout. A suitable CAN transceiver, protection network, reference clock, and automotive-rated power architecture must be evaluated separately for the vehicle environment.

🏭

Industrial Automation Node

The AT90CAN128-16MJ is appropriate for a distributed industrial controller that monitors inputs and drives outputs while sharing operating data over a CAN bus. Its 53 GPIO lines reduce the need for external digital I/O expansion, and four timer/counter blocks support timing and PWM tasks. The 16 MHz AVR core manages communication and control firmware, while 4 KB of EEPROM preserves configuration values across power cycles. Industrial implementations should add suitable isolation, surge protection, watchdog strategy, and environmental qualification beyond the MCU itself.

🧩

CAN-Connected Sensor Controller

The AT90CAN128-16MJ can serve as the local controller for a CAN-connected sensor or actuator, combining data acquisition, logic, timers, and network communication in one device. Its 128 KB of ISP flash accommodates drivers, filtering, calibration, and protocol code, while the CAN controller offloads frame handling from the CPU. The 64-QFN footprint is useful in compact instrumentation. Designers must allocate pins for the selected sensors, provide a precision clock as required, and use the manufacturer pin table to avoid conflicts among CAN, serial, timer, and GPIO functions.

🔧

Vehicle Diagnostic Interface

The AT90CAN128-16MJ fits a diagnostic interface that connects vehicle CAN traffic to a service tool, display, or service computer. The integrated CAN controller supports standard frame handling, while 128 KB of flash provides space for diagnostic identifiers, message filtering, fault logging, and communications software. Its two USARTs and SPI interface can connect to a host and local storage or display. For a production diagnostic product, verify transceiver fault behavior, bus termination, ESD protection, supply transients, and the required automotive temperature and qualification conditions.

🏠

Building Control Terminal

The AT90CAN128-16MJ can implement a connected building-control terminal for lighting, HVAC, access equipment, or environmental sensors. Its 53 GPIO lines support multiple digital inputs and outputs, while the CAN controller enables distributed communication with floor controllers or building equipment. Two USARTs, SPI, timers, PWM outputs, and 4 KB of EEPROM broaden the terminal capabilities beyond basic bus control. Firmware can implement debounce, actuation limits, fault reporting, and local overrides, while the compact QFN package supports space-constrained control panels.

🖥️

Embedded Test and Control Module

The AT90CAN128-16MJ is suitable for a compact test or control module that combines stimulus sequencing, measurement control, logging, and CAN communication. Four timer/counter blocks support timing and PWM functions, 53 GPIO lines connect to control logic, and 4 KB of SRAM supports working buffers. The 128 KB flash region accommodates firmware images, test sequences, and diagnostic routines. The device should be paired with suitable analog front-end circuitry because the MCU's GPIO and communications peripherals do not replace precision measurement or high-voltage driver stages.

What is the AT90CAN128-16MJ?
The AT90CAN128-16MJ is a 16 MHz 8-bit AVR microcontroller with 128 KB of flash memory, 4 KB of EEPROM, 4 KB of SRAM, 53 GPIO lines, and an integrated CAN 2.0A/CAN 2.0B controller. According to the Microchip AT90CAN128 product page, the device combines the CAN controller, two USARTs, SPI, two-wire serial, timers, and other peripherals in a 64-QFN package measuring 9 x 9 mm.
What is the operating voltage of AT90CAN128-16MJ?
The AT90CAN128-16MJ operates from the supply-voltage range specified for the AT90CAN128 family in the manufacturer datasheet. Confirm that voltage before connecting external sensors, transceivers, or actuators because the MCU supply limits and each attached device's operating range determine which components can share a rail. Use the family datasheet's electrical-characteristics table for the definitive minimum and maximum supply values.
Where can I download the AT90CAN128 datasheet PDF?
The official AT90CAN128 documentation is available from the Microchip product page at https://www.microchip.com/en-us/product/AT90CAN128. The manufacturer datasheet is the authoritative source for the 64-pin assignments, electrical limits, clock requirements, programming connectors, and package drawings. A separate Octopart datasheet link is also listed, but the Microchip document should control engineering decisions.
Where can I find the AT90CAN128 pinout?
The AT90CAN128 pinout is found in the pin-description table and package drawing in the Microchip manufacturer datasheet. The AT90CAN128-16MJ uses a 64-QFN package, so verify every pin against the -16MJ ordering information rather than assuming the pinout of another package option. Pay particular attention to supply pins, ground pins, programming signals, crystal connections, and the exposed thermal pad.
How is AT90CAN128-16MJ programmed?
The AT90CAN128-16MJ supports in-system programming through its ISP flash interface. The manufacturer product page identifies 128 KB of ISP flash memory, and the datasheet defines the programming signals, connector arrangement, clock requirements, and fuse access. Follow the documented ISP procedure and ensure the external clock and power conditions are valid during programming.
Does AT90CAN128-16MJ have a CAN controller?
Yes, the AT90CAN128-16MJ includes a hardware CAN controller compliant with CAN 2.0A and CAN 2.0B. The controller manages CAN frames and supports communication tasks, but the MCU requires an external CAN transceiver to convert its logic-level CAN TX and RX signals to the physical bus. Select a transceiver compatible with the board supply, bus speed, termination, isolation, and fault requirements.
What memory and peripherals does AT90CAN128-16MJ provide?
The AT90CAN128-16MJ provides 128 KB of ISP flash, 4 KB of EEPROM, 4 KB of SRAM, 53 general-purpose I/O lines, and 32 working registers. Its peripheral set includes four flexible timer/counter blocks, two USARTs, SPI, a byte-oriented two-wire serial interface, and a CAN controller. These resources support concurrent communications, timing, PWM, and digital control functions.
When should I choose AT90CAN128-16MJ over another AVR microcontroller?
Choose the AT90CAN128-16MJ when the design specifically benefits from its integrated CAN controller, 128 KB of flash, and 53 GPIO lines in a compact 64-QFN package. Select a smaller or lower-pin-count MCU when CAN is unnecessary or when a less demanding package is preferred. Confirm that 16 MHz is sufficient for the control loop, protocol workload, and peripheral timing requirements.
What is the difference between AT90CAN128-16MJ and AT90CAN128-16AU?
The AT90CAN128-16MJ and AT90CAN128-16AU belong to the same 16 MHz AT90CAN128 family, but the ordering suffix identifies different physical packages. The -16MJ version uses a 64-QFN package measuring 9 x 9 mm, whereas the -16AU version is associated with a 64-lead TQFP package. Verify the manufacturer pin and package drawings before treating either option as a PCB-level replacement.
Is AT90CAN128-16MU a drop-in replacement for AT90CAN128-16MJ?
The AT90CAN128-16MU is not a drop-in replacement for the AT90CAN128-16MJ because the package forms differ. The -16MU ordering code denotes a 64-lead TQFP package, while the -16MJ uses a 64-QFN package measuring 9 x 9 mm. Both are 16 MHz members of the AT90CAN128 family, but changing package type requires a different footprint, land pattern, pin orientation, and assembly process.
What can replace AT90CAN128-16MJ in an existing design?
The safest replacement is the exact AT90CAN128-16MJ ordering code, including its package and temperature configuration. A different family member can preserve much of the firmware architecture only after its package drawing, pin functions, clock behavior, electrical limits, and peripheral resources have been compared. No additional pin-compatible same-package replacement is established by the available cross-reference records, so PCB changes should not be assumed.
Where can I buy AT90CAN128-16MJ and check its price?
Use the Request a Quote form on this page to request AT90CAN128-16MJ pricing, stock confirmation, lead time, and minimum order quantity. Quote requests preserve the exact 64-QFN ordering code and let procurement confirm current lifecycle and supply conditions. Because the device is identified as obsolete, request written confirmation of stock, date code, traceability, and scheduled allocation before releasing a production order.
What is the lead time for AT90CAN128-16MJ?
Lead time for the AT90CAN128-16MJ depends on remaining factory inventory, scheduled allocations, and the quantity requested. Submit a Request a Quote with the required quantity, target date, and acceptable date codes. Procurement should confirm current availability and the expected delivery schedule before the order is placed, particularly for an obsolete component where no future production can be assumed.
Is AT90CAN128-16MJ in stock?
Stock status changes by seller, lot, and quantity, so the Request a Quote form on this page should be used for a current AT90CAN128-16MJ availability check. Ask for the exact suffix, package, quantity, date code, manufacturer traceability, and any factory allocation. Do not base a production release on an inventory count obtained for a different AT90CAN128 package or ordering option.
What are the key specifications engineers should know about AT90CAN128-16MJ?
The key AT90CAN128-16MJ specifications are a 16 MHz 8-bit AVR core, 128 KB of ISP flash, 4 KB of EEPROM, 4 KB of SRAM, 53 GPIO lines, 32 working registers, and hardware CAN 2.0A/CAN 2.0B support. The package is a 64-QFN measuring 9 x 9 mm with an exposed pad. These figures make the device appropriate for CAN-connected embedded control systems requiring substantial firmware and mixed peripheral support.
What is the best cross-brand equivalent for AT90CAN128-16MJ?
No cross-brand equivalent is established as a true drop-in replacement for the AT90CAN128-16MJ. The available cross-reference results provide search tools and related AT90CAN128 family comparisons, but they do not verify that another manufacturer's MCU has the same 64-QFN footprint, pin functions, CAN implementation, clock system, and electrical behavior. A redesign can be evaluated separately, while a production substitution should remain an exact ordering-code match.

엔지니어링 참조 데이터: AT90CAN128-16MJ — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the AT90CAN128-16MJ when an existing or new design requires a 16 MHz AVR microcontroller with 128 KB of flash, 4 KB each of SRAM and EEPROM, 53 GPIO lines, and an integrated CAN 2.0A/CAN 2.0B controller in a compact 64-QFN footprint. It is particularly useful when board area is constrained and the PCB can be manufactured with fine-pitch QFN handling and an exposed-pad thermal design. The AT90CAN128-16AU and AT90CAN128-16MU offer the same 16 MHz family architecture in 64-lead TQFP packages, making them suitable when assembly capability or prototype access favors through-hole-style package leads; however, they are not drop-ins for the -16MJ land pattern. For a new design, compare the QFN option against TQFP family versions using package size, assembly yield, thermal performance, sourcing, and lifecycle rather than assuming functional interchangeability. No cross-brand drop-in equivalent has been verified, so changing MCU vendors requires a full firmware, electrical, and PCB review.

대체품과의 비교

파라미터 이 제품 AT90CAN128-16AU AT90CAN128-16MU AT90CAN128-16MUR
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 64-QFN, 9 x 9 mm 64-lead TQFP 64-lead TQFP 64-lead TQFP
Clock Frequency 16 MHz 16 MHz 16 MHz 16 MHz
Flash Memory 128 KB 128 KB 128 KB 128 KB
EEPROM Memory 4 KB 4 KB 4 KB 4 KB
SRAM 4 KB 4 KB 4 KB 4 KB
GPIO Lines 53 53 53 53
CAN Controller CAN 2.0A and CAN 2.0B CAN 2.0A and CAN 2.0B CAN 2.0A and CAN 2.0B CAN 2.0A and CAN 2.0B

주요 차별점

  • Compact package for CAN-connected embedded controllers (vs AT90CAN128-16MU)
  • Same 16 MHz CAN controller architecture in related package options (vs AT90CAN128-16AU)
  • Integrated communications and control resources (vs AT90CAN128-16MUR)

설계 노트

Use the manufacturer package drawing and pin-description table to build the 64-QFN land pattern. Assign the exposed pad to the required ground or power-plane connection, provide uninterrupted thermal-via arrays beneath it, and keep high-speed or sensitive nets away from the pad's copper return path. Confirm the selected assembly process supports the package pitch and inspect the pin-1 orientation before releasing artwork.

The MCU requires a local low-impedance supply network because the CAN transceiver, clock circuitry, and connected loads may create fast current transitions. Follow the manufacturer bypass-capacitor recommendations, place the required decoupling capacitance directly at the relevant supply pins, and provide adequate bulk energy close to the device. Confirm startup current, supply tolerance, and clock ramp behavior against the exact -16MJ electrical requirements.

Keep the MCU CAN TX and RX traces short and route them away from clocks, switching nodes, and high-current outputs. The MCU contains the protocol controller but not the physical bus driver, so the external transceiver determines bus-level timing and fault tolerance. Match interfaces, isolate the transceiver if required by the system, apply the designated bus protection network, and verify termination placement at physically correct locations.

Do not substitute the -16AU, -16MU, or -16MUR ordering codes as PCB drop-ins for the -16MJ device; these family members use a different package from the 64-QFN target. Likewise, confirm that a cross-family MCU exposes equivalent clock, programming, reset, interrupt, and CAN resources. For an existing design, verify every net against both package drawings and treat any footprint or pin-function difference as a redesign.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

The exact AT90CAN128-16MJ qualification and environmental-compliance declarations must be confirmed from the manufacturer product page and the lot-specific documentation.

데이터 검증일: 2026-11-20 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

at90can128 datasheet at90can128 pinout at90can128 16au datasheet at90can128 programming at90can128 development board at90can128 pdf AT90CAN128-16MJ datasheet AT90CAN128-16MJ pinout AT90CAN128-16MJ equivalent AT90CAN128-16MJ replacement AT90CAN128-16MJ vs AT90CAN128-16MU AT90CAN128-16MJ QFN application AT90CAN128-16MJ price AT90CAN128-16MJ stock Microchip AT90CAN128-16MJ

관련 부품 & 용어

Microchip Technology AT90CAN128-16MJ AT90CAN128 AT90CAN128-16AU AT90CAN128-16MU AT90CAN128-16MUR AVR 90CAN AVR RISC 8-bit microcontroller embedded microcontroller CAN controller CAN 2.0A CAN 2.0B ISP flash 16 MHz 128 KB flash memory 4 KB EEPROM 4 KB SRAM 53 GPIO lines USART SPI two-wire serial interface timer/counter 64-QFN QFN family surface-mount package exposed pad industrial automation automotive CAN
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기