ATMEGA168A-MU - 8-bit AVR MCU 16KB Flash 20MHz VQFN-32 | Microchip
부품 번호: ATMEGA168A-MU ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $2.42 | $2.42 |
| 10 | $2.18 | $21.80 |
| 100 | $1.86 | $186.00 |
| 500 | $1.62 | $810.00 |
| 1,000 | $1.38 | $1,380.00 |
ATMEGA168A-MU 개요
An 8-bit microcontroller (MCU) is a single integrated circuit containing a processor core, memory, and programmable input/output peripherals. Within the power-management and embedded-control hierarchy, the ATmega168A belongs to the AVR family of reduced-instruction-set (RISC) controllers, positioned as the mid-memory variant of the ATmega48/88/168/328 product ladder. Such MCUs execute control, sensing, and communication tasks in embedded systems ranging from consumer appliances to industrial nodes.
Key features include 133 powerful instructions with most executed in a single clock cycle, delivering up to 20 MIPS throughput at 20 MHz. The device offers 23 general-purpose I/O lines, 32 general-purpose working registers, three flexible timer/counters with compare modes, and both internal and external interrupt sources. Serial connectivity is comprehensive: a byte-oriented 2-wire interface (I2C/TWI), a programmable USART, and an SPI serial port. On-chip analog resources include a 6-channel 10-bit ADC in the QFN package variant.
The AVR enhanced RISC architecture combines a rich instruction set with 32 general-purpose working registers directly connected to the arithmetic logic unit, allowing every register access to complete in one cycle. In-system programmable flash with read-while-write support permits firmware updates on the assembled board through SPI, and the picoPower-compatible low-power modes (idle, power-down, power-save) reduce consumption for battery designs.
Typical applications include sensor acquisition nodes using the 10-bit ADC, motor and LED control via the timer PWM channels, and serial communication bridges using USART, SPI, or TWI. It is also a common choice for Arduino-compatible board designs and hobby-to-industrial migration paths.
When designing with the ATMEGA168A-MU, ensure decoupling capacitors sit close to the multiple VCC/AVCC pins of the exposed-pad VQFN-32, and connect the exposed pad to ground for thermal and noise performance.
This page synthesizes distributor availability data, drop-in alternatives, pinout detail, and practical design notes not consolidated in the manufacturer datasheet.
드롭인 대체품: ATMEGA168A-MU — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ATMEGA168A-MU (동일 폼 팩터 및 풋프린트) — 차이점: Package, Operating Temperature, Timers, Communication Interfaces, Programming.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
ATMEGA168PA-MU
✅ 드롭인✓ 재고 있음
$1.72 / 개
데이터시트 보기 →ATMEGA168A-MMHR
✅ 드롭인✓ 재고 있음
$1.58 / 개
데이터시트 보기 →ATMEGA168-20MU
✅ 드롭인✓ 재고 있음
가격 문의
데이터시트 보기 →ATMEGA88A-MU
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ATMEGA48A-MU
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ATMEGA328P-MU
✅ 드롭인✓ 재고 있음
$2.85 / 개
데이터시트 보기 →ATMEGA168A-MU 최대 정격 & 전기적 특성
| Core Architecture | 8-bit AVR RISC |
| Flash Memory | 16 KB (8K x 16) ISP |
| EEPROM | 512 B |
| SRAM | 1 KB |
| 최대 클록 주파수 | 20 MHz |
| Maximum Throughput | 20 MIPS at 20 MHz |
| Supply Voltage Range | 2.7 V to 5.5 V |
| General Purpose I/O Lines | 23 |
| Working Registers | 32 x 8-bit general purpose |
| Timer/Counters | 3 flexible with compare modes |
| ADC | 10-bit, 6-channel (QFN package) |
| Serial Interfaces | USART, SPI, 2-wire (I2C/TWI) |
| 패키지 | 32-VQFN (5x5 mm) exposed pad |
| 실장 유형 | Surface Mount |
| 수명 주기 상태 | Active |
| 데이터 버스 폭 | 8 bit |
| Instruction Set | 133 instructions, mostly single-cycle |
ATMEGA168A-MU 핀 구성
| 핀 1 | PD3 (PCINT19/OC2B/INT1) — Port D, pin-change interrupt / Timer2 output compare B / external interrupt 1 |
| 핀 2 | PD4 (PCINT20/XCK/T0) — Port D, USART external clock / Timer0 external clock |
| 핀 3 | GND — Ground |
| 핀 4 | VCC — Digital supply voltage |
| 핀 5 | GND — Ground |
| 핀 6 | VCC — Digital supply voltage |
| 핀 7 | PB6 (PCINT6/XTAL1/TOSC1) — Crystal oscillator input / Timer oscillator |
| 핀 8 | PB7 (PCINT7/XTAL2/TOSC2) — Crystal oscillator output |
| 핀 9 | PD5 (PCINT21/OC0B/T1) — Port D, Timer0 output compare B / Timer1 external clock |
| 핀 10 | PD6 (PCINT22/OC0A/AIN0) — Port D, Timer0 output compare A / analog comparator positive input |
| 핀 11 | PD7 (PCINT23/AIN1) — Port D, analog comparator negative input |
| 핀 12 | PB0 (PCINT0/CLKO/ICP1) — Port B, clock output / Timer1 input capture |
| 핀 13 | PB1 (PCINT1/OC1A) — Port B, Timer1 output compare A |
| 핀 14 | PB2 (PCINT2/SS/OC1B) — Port B, SPI slave select / Timer1 output compare B |
| 핀 15 | PB3 (PCINT3/MOSI/OC2A) — Port B, SPI master output / Timer2 output compare A |
| 핀 16 | PB4 (PCINT4/MISO) — Port B, SPI master input |
| 핀 17 | PB5 (PCINT5/SCK) — Port B, SPI serial clock |
| 핀 18 | AVCC — ADC supply voltage |
| 핀 19 | ADC6 — ADC input channel 6 |
| 핀 20 | AREF — Analog reference voltage |
| 핀 21 | GND — Ground |
| 핀 22 | ADC7 — ADC input channel 7 |
| 핀 23 | PC0 (PCINT8/ADC8) — Port C, ADC channel 8 |
| 핀 24 | PC1 (PCINT9/ADC9) — Port C, ADC channel 9 |
| 핀 25 | PC2 (PCINT10/ADC10) — Port C, ADC channel 10 |
| 핀 26 | PC3 (PCINT11/ADC11) — Port C, ADC channel 11 |
| 핀 27 | PC4 (PCINT12/SDA/ADC12) — Port C, TWI data / ADC channel 12 |
| 핀 28 | PC5 (PCINT13/SCL/ADC13) — Port C, TWI clock / ADC channel 13 |
| 핀 29 | PC6 (PCINT14/RESET) — Reset input / port pin |
| 핀 30 | PD0 (PCINT16/RXD) — Port D, USART receive |
| 핀 31 | PD1 (PCINT17/TXD) — Port D, USART transmit |
| 핀 32 | PD2 (PCINT18/INT0) — Port D, external interrupt 0 |
일반적인 애플리케이션
ATMEGA168A-MU 적합 용도: 6 애플리케이션s: Sensor Acquisition Nodes, Motor and LED Control, Industrial Communication Bridges, Consumer Appliance Control, Arduino-Compatible Prototyping, IoT End Nodes and Remote Monitoring.
Sensor Acquisition Nodes
The ATMEGA168A-MU fits battery-powered and wired sensor nodes because its integrated 10-bit ADC offers up to 6 channels in the QFN package, eliminating an external converter for thermistor, potentiometer, or analog accelerometer interfaces. The 20 MIPS throughput at 20 MHz handles oversampling and digital filtering while the 1 KB SRAM buffers sample windows. Placed in power-down sleep between conversions, the AVR wakes on external interrupt or watchdog timeout, keeping average current in the microampere-to-milliampere range depending on duty cycle. The VQFN-32 5x5 mm footprint supports compact PCB sensor modules, and the TWI bus can chain digital sensors such as the AT30TS750 temperature sensor alongside the analog inputs.
추천
Motor and LED Control
Three flexible timer/counters with compare modes make the ATMEGA168A-MU well suited to PWM generation for DC motor speed control and LED dimming. The 16-bit Timer/Counter1 provides high-resolution PWM while two 8-bit timers handle auxiliary channels or tick scheduling. With 23 GPIO lines, the MCU can drive a gate-driver front end such as the MIC4102 half-bridge driver for brushed or stepper motors. Because PWM generation is hardware-based, CPU load remains low for supervisory tasks like current-limit protection through the ADC. At 20 MHz, PWM carrier frequencies well above audible range are achievable, avoiding LED flicker and motor whine in consumer products.
추천
Industrial Communication Bridges
The ATMEGA168A-MU integrates a hardware USART, SPI, and byte-oriented 2-wire (I2C/TWI) interface, allowing protocol conversion between legacy serial devices and modern buses. A typical bridge design places the MCU between an RS-485 transceiver such as the ATA6561 on the USART side and SPI peripherals on the other, forwarding Modbus-RTU frames with CRC computed in firmware within the 20 MIPS budget. The 512 B EEPROM stores node addresses and configuration persistently, and the 16 KB flash holds protocol stacks comfortably. Hardware SPI supports multi-slave arbitration with chip-select GPIOs, and the read-while-write flash allows field firmware updates without removing the device from the industrial network.
추천
Consumer Appliance Control
In appliances such as coffee makers, fans, and small HVAC controls, the ATMEGA168A-MU provides the right balance of cost, memory, and integration. The 2.7 V to 5.5 V supply range accepts mains-derived linear supplies without a dedicated regulator IC in many designs. Timer PWM drives triac or relay timing, touch-button decoding uses ADC channels or pin-change interrupts, and the USART supports service diagnostics. The 5x5 mm VQFN-32 package suits dense main-PCB layouts where DIP MCUs would not fit. Firmware for temperature profiles and user-interface state machines fits easily in 16 KB, and the 32 general-purpose registers simplify interrupt-driven UI code with low register-bank switching overhead.
추천
Arduino-Compatible Prototyping
The ATMEGA168A-MU is the 16 KB sibling of the ATmega328P used on the Arduino Uno and is fully supported by the Arduino IDE via the ATmega168 board definition. Designers building custom Arduino-compatible boards use the same 16 MHz crystal, ISP header, and FTDI/USB-serial front end; a bootloader such as Optiboot fits within the 16 KB flash when trimmed. The 10-bit ADC maps directly to analogRead(), and hardware SPI/TWI support the Wire and SPI libraries unchanged. For prototypes expected to grow past 16 KB, designing the footprint to accept the pin-compatible ATMEGA328P-MU preserves layout investment while doubling program space at production time.
추천
IoT End Nodes and Remote Monitoring
For sub-GHz and LPWAN IoT nodes, the ATMEGA168A-MU acts as the application controller driving a radio module over SPI or UART. Its sleep modes are critical: in power-down between reporting intervals, current consumption drops to the microampere range, enabling multi-year battery life when paired with a sensor and a low-power radio such as the ATA578x receiver family. The 512 B EEPROM stores device IDs and calibration constants, and the ADC reads battery voltage via divider for health telemetry. Wake-up via watchdog or external interrupt from a motion sensor keeps the design event-driven. The compact VQFN-32 package allows the controller to share a small PCB with the RF section.
추천
추천 제품 요약
엔지니어링 참조 데이터: ATMEGA168A-MU — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ATMEGA168PA-MU | ATMEGA88A-MU | ATMEGA48A-MU | ATMEGA328P-MU |
|---|---|---|---|---|---|
| Package | 32-VQFN (5x5 mm) | 32-VQFN (5x5 mm) - same | 32-VQFN (5x5 mm) - same | 32-VQFN (5x5 mm) - same | 32-VQFN (5x5 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 16 KB | 16 KB | 8 KB | 4 KB | 32 KB |
| SRAM | 1 KB | 1 KB | 1 KB | 512 B | 2 KB |
| EEPROM | 512 B | 512 B | 512 B | 256 B | 1 KB |
| Maximum Clock | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Supply Voltage | 2.7 V to 5.5 V | 1.8 V to 5.5 V (PA speed grades) | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 1.8 V to 5.5 V (P speed grades) |
| Low Power Technology | Standard AVR sleep modes | picoPower | Standard AVR sleep modes | Standard AVR sleep modes | picoPower |
| Drop-in Compatible with ATMEGA168A-MU | - | Yes - pin-to-pin | Yes - pin-to-pin (less flash) | Yes - pin-to-pin (less flash) | Yes - pin-to-pin (more flash) |
주요 차별점
- Balanced 16 KB flash tier in the AVR memory ladder (vs ATMEGA88A-MU)
- Lowest-cost option for large memory needs (vs ATMEGA328P-MU)
- Honest trade-off: no picoPower technology (vs ATMEGA168PA-MU)
- More SRAM than the smallest family member (vs ATMEGA48A-MU)
설계 노트
The ATMEGA168A-MU VQFN-32 has two VCC pins (4, 6), AVCC (18), and multiple ground pins (3, 5, 21) plus an exposed thermal pad. Connect every VCC and AVCC pin to the 5 V or 3.3 V rail with a 100 nF ceramic capacitor placed within 2 mm of each pin, and tie AVCC to VCC through an LC filter (10 uH + 100 nF) when ADC accuracy matters. Solder the exposed pad to a grounded copper pour; it improves heat dissipation and reduces ground bounce for the ADC and comparator.
At 5 V and 20 MHz, active-mode current is in the several-milliampere range per the datasheet electrical characteristics; in power-down sleep it falls to the microampere range. Estimated: a node sleeping 99% of the time at 1 uA and active 1% at 5 mA draws an average of roughly 51 uA, which a 500 mAh CR2032 supports for well over a year. If battery life is the binding constraint, use the pin-compatible picoPower ATMEGA168PA-MU which lowers sleep current further without layout changes.
Fuse misconfiguration is the most common field failure with AVR devices: selecting external clock when only a crystal is fitted, or disabling SPI when ISP programming is needed, can lock the part. Always verify fuse settings (low/high/extended byte) against the family datasheet before flashing, and keep the reset pin (PC6) decoupled with a 100 nF capacitor with a 10 kohm pull-up for reliable brown-out behavior. Enable the internal brown-out detector for mains-powered designs to prevent EEPROM corruption during power glitches.
For ADC measurements, keep analog traces (AREF, ADC channels) short and away from crystal and PWM switching lines. Use the ADC noise reduction sleep mode during conversions: it halts the CPU and I/O clocks, measurably reducing quantization noise. A 100 nF capacitor directly on AREF with the internal reference selected gives the most repeatable results; avoid driving AREF externally while the internal reference is enabled, as this can damage the reference amplifier per the datasheet.
규정 준수 정보
Compliance status not stated in the provided verified web data; consult the Microchip product page and product environmental data for RoHS/REACH details.
