ATSAMD51J18A-AU-EFP - 120MHz Cortex-M4F MCU, 256KB Flash | Microchip
부품 번호: ATSAMD51J18A-AU-EFP ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $6.85 | $6.85 |
| 10 | $6.17 | $61.70 |
| 100 | $5.48 | $548.00 |
| 500 | $4.93 | $2,465.00 |
| 1,000 | $4.38 | $4,380.00 |
| 3,000 | $3.95 | $11,850.00 |
ATSAMD51J18A-AU-EFP 개요
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash for program code and SRAM for data), and a rich set of peripherals such as timers, communication interfaces, and analog blocks. Within the broader taxonomy, the ATSAMD51J18A sits in the hierarchy: microcontroller -> 32-bit MCU -> ARM Cortex-M class -> Cortex-M4F (with Floating Point Unit and DSP extensions) -> general-purpose MCU. The FPU accelerates single-precision floating-point math, while DSP extensions enable MAC instructions and SIMD-style operations, both critical for sensor-fusion and signal-processing workloads at low power.
Key specifications include 256 KB Flash with ECC, 128 KB SRAM with ECC, 120 MHz Cortex-M4F core, 12-bit 1 Msps ADC with up to 16 channels, 10-bit 350 ksps DAC, six SERCOM configurable serial interfaces (UART/SPI/I2C), USB 2.0 Full-Speed with on-chip PHY, I2S, and an Event System for inter-peripheral signaling. Operating voltage spans 1.71 V to 3.63 V, with a -40C to +85C industrial temperature range, making it well-suited for harsh-environment designs.
Architecturally, the ATSAMD51J18A uses a dual-bank Flash with EEPROM emulation support and a 4 KB cache that masks Flash wait-states to sustain single-cycle execution at 120 MHz. The peripheral event system and DMAC offload CPU overhead, allowing deterministic real-time response for motor control, audio decoding, or multi-protocol sensor hubs.
Typical applications include industrial IoT gateways, USB-C HID peripherals, portable medical instrumentation, audio effects processors, and low-power robotics controllers. The combination of DSP instructions, FPU, USB, and ample analog peripherals lets a single MCU replace an MPU-plus-external-DSP architecture in cost-sensitive designs.
Designers should allocate decoupling capacitors near each VDD pin (100 nF plus bulk 4.7 uF) and follow Microchip's SAM D51 hardware design checklist for crystal layout. For lowest active power, use the SleepWalking mode, and configure the ADC with internal reference and proper acquisition timing to avoid channel crosstalk.
This page combines datasheet specifications, distributor pricing, drop-in alternatives, and practical design notes not collated on the manufacturer datasheet, giving engineers a single reference for evaluation and BOM decisions.
드롭인 대체품: ATSAMD51J18A-AU-EFP — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ATSAMD51J18A-AU-EFP (동일 폼 팩터 및 풋프린트) — 차이점: DAC, SRAM, USB, Operating Temperature, Package.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
ATSAMD51J18A-AU
✅ 드롭인✓ 재고 있음
$4.39 / 개
데이터시트 보기 →ATSAMD51J19A-AU-EFP
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ATSAMD51N20A-AU-EFP
✅ 드롭인✓ 재고 있음
$9.42 / 개
데이터시트 보기 →ATSAMD51J18A-AUT-EFP
✅ 드롭인✓ 재고 있음
$4.88 / 개
데이터시트 보기 →ATSAMD51G19A-MFT
✅ 드롭인✓ 재고 있음
$4.02 / 개
데이터시트 보기 →ATSAMD51G18A-MFT
✅ 드롭인✓ 재고 있음
$3.55 / 개
데이터시트 보기 →ATSAMD51J18A-AU-EFP 최대 정격 & 전기적 특성
| Core | ARM Cortex-M4F with FPU and DSP |
| Maximum CPU Speed | 120 MHz |
| Program Flash | 256 KB (256K x 8) with ECC |
| SRAM | 128 KB with ECC |
| 패키지 | 64-TQFP (10x10 mm) |
| Operating Voltage | 1.71 V to 3.63 V |
| 동작 온도 | -40C to +85C |
| ADC | 12-bit, up to 1 Msps, up to 16 channels |
| DAC | 10-bit, 350 ksps, 2 channels |
| USB | USB 2.0 Full-Speed with on-chip PHY |
| Configurable SERCOM | 6 (UART/SPI/I2C/LIN) |
| I2S | Yes |
| Timers (TC/TCC) | Yes (multiple 16-bit) |
| DMA Channels | DMAC, multiple channels |
| 실장 유형 | Surface Mount |
| MSL 레벨 | 3 (168 hours) |
| RoHS 상태 | Compliant |
| Lead-Free | Yes |
ATSAMD51J18A-AU-EFP 핀 구성
| 핀 1 | PA00 — GPIO / XIN32 (32.768 kHz crystal input) |
| 핀 2 | PA01 — GPIO / XOUT32 (32.768 kHz crystal output) |
| 핀 3 | PA02 — GPIO / AIN0 (ADC input) |
| 핀 4 | PA03 — GPIO / AIN1 / VREFA (ADC reference) |
| 핀 5 | GND — Ground |
| 핀 6 | VDDIO — I/O supply voltage |
| 핀 7 | PA04 — GPIO / AIN2 |
| 핀 8 | PA05 — GPIO / AIN3 |
| 핀 9 | PA06 — GPIO / AIN4 |
| 핀 10 | PA07 — GPIO / AIN5 |
| 핀 11 | PA08 — GPIO / AIN6 / I2S FS |
| 핀 12 | PA09 — GPIO / AIN7 / I2S MCK |
| 핀 13 | PA10 — GPIO / AIN8 / I2S SCK |
| 핀 14 | PA11 — GPIO / AIN9 / I2S SDO |
| 핀 15 | VDDIO — I/O supply voltage |
| 핀 16 | GND — Ground |
| 핀 17 | PB10 — GPIO / I2S SDI |
| 핀 18 | PB11 — GPIO |
| 핀 19 | PB12 — GPIO |
| 핀 20 | PB13 — GPIO |
| 핀 21 | PB14 — GPIO |
| 핀 22 | PB15 — GPIO |
| 핀 23 | PA12 — GPIO / USB DP |
| 핀 24 | PA13 — GPIO / USB DM |
| 핀 25 | PA14 — GPIO / XIN (main crystal input) |
| 핀 26 | PA15 — GPIO / XOUT (main crystal output) |
| 핀 27 | GND — Ground |
| 핀 28 | VDDIN — Voltage regulator input |
| 핀 29 | VDDCORE — Internal core voltage (decoupling) |
| 핀 30 | VDDIO — I/O supply voltage |
| 핀 31 | PA16 — GPIO / SERCOM1 PAD0 |
| 핀 32 | PA17 — GPIO / SERCOM1 PAD1 |
| 핀 33 | PA18 — GPIO / SERCOM1 PAD2 |
| 핀 34 | PA19 — GPIO / SERCOM1 PAD3 |
| 핀 35 | PA20 — GPIO / SERCOM3 PAD0 |
| 핀 36 | PA21 — GPIO / SERCOM3 PAD1 |
| 핀 37 | PA22 — GPIO / SERCOM3 PAD2 |
| 핀 38 | PA23 — GPIO / SERCOM3 PAD3 |
| 핀 39 | PA24 — GPIO / USB VBUS sense |
| 핀 40 | PA25 — GPIO |
| 핀 41 | GND — Ground |
| 핀 42 | VDDIO — I/O supply voltage |
| 핀 43 | PB16 — GPIO / SERCOM5 PAD0 |
| 핀 44 | PB17 — GPIO / SERCOM5 PAD1 |
| 핀 45 | PB18 — GPIO / SERCOM5 PAD2 |
| 핀 46 | PB19 — GPIO / SERCOM5 PAD3 |
| 핀 47 | PB20 — GPIO / SERCOM3 PAD0 |
| 핀 48 | PB21 — GPIO / SERCOM3 PAD1 |
| 핀 49 | PA27 — GPIO |
| 핀 50 | RESET — Reset input (active-low) |
| 핀 51 | PA30 — GPIO / SWCLK (programming) |
| 핀 52 | PA31 — GPIO / SWDIO (programming) |
| 핀 53 | PB22 — GPIO / SERCOM7 PAD0 |
| 핀 54 | PB23 — GPIO / SERCOM7 PAD1 |
| 핀 55 | PB24 — GPIO |
| 핀 56 | PB25 — GPIO |
| 핀 57 | PA02 — GPIO / DAC VOUT (alternate) |
| 핀 58 | PA03 — GPIO / DAC VREFA (alternate) |
| 핀 59 | GND — Ground |
| 핀 60 | VDDIO — I/O supply voltage |
| 핀 61 | PA05 — GPIO / SERCOM0 PAD1 (alternate) |
| 핀 62 | PA06 — GPIO / SERCOM0 PAD2 (alternate) |
| 핀 63 | PA07 — GPIO / SERCOM2 PAD3 (alternate) |
| 핀 64 | PA08 — GPIO / SERCOM2 PAD0 (alternate) |
일반적인 애플리케이션
ATSAMD51J18A-AU-EFP 적합 용도: 7 애플리케이션s: Industrial IoT Sensor Hub, USB-C HID Peripheral Devices, Portable Audio Effects Processor, Battery-Powered Wearable Device, Robotics Motor Controller, Medical Point-of-Care Diagnostic Device, Smart Home Edge Gateway.
Industrial IoT Sensor Hub
The ATSAMD51J18A-AU-EFP fits industrial IoT sensor hubs because its Cortex-M4F core at 120 MHz executes floating-point sensor-fusion algorithms in real time while drawing low active power. The 12-bit 1 Msps ADC samples up to 16 analog channels for multi-sensor arrays (temperature, pressure, vibration), while six SERCOM ports handle I2C/SPI sensor peripherals concurrently. Integrated USB 2.0 Full-Speed with on-chip PHY provides local diagnostics without an external PHY chip. With 256 KB Flash and 128 KB SRAM, designers can run FreeRTOS plus MQTT-SN, TLS stack, and application logic. The wide 1.71-3.63 V supply range supports battery or 3.3 V industrial bus operation.
추천
USB-C HID Peripheral Devices
The ATSAMD51J18A-AU-EFP is ideal for USB-C Human Interface Devices because the integrated USB 2.0 Full-Speed controller with on-chip PHY eliminates external USB transceivers, reducing BOM cost. The 120 MHz Cortex-M4F core handles USB HID report generation plus key matrix scanning or capacitive touch processing in real time. Developers can implement keyboards, mice, touch panels, and game controllers using the 6 SERCOM ports for additional peripherals. With 256 KB Flash, full HID descriptor stacks fit comfortably alongside composite USB device support (HID + CDC + MSD). The 64-TQFP package exposes up to 51 GPIO pins for LED indicators, button arrays, and rotary encoders.
추천
Portable Audio Effects Processor
The ATSAMD51J18A-AU-EFP is well suited for portable audio effects processors thanks to its Cortex-M4F core with single-precision FPU and DSP MAC instructions. At 120 MHz, the core executes real-time audio DSP algorithms (EQ, reverb, compression) across stereo 48 kHz sample streams with sufficient headroom. The integrated I2S peripheral interfaces directly to 24-bit audio codecs, while the 10-bit DAC and 12-bit ADC support analog audio I/O for entry-level designs. With 256 KB Flash, designers can include multi-effect presets and USB-MIDI firmware; the 128 KB SRAM buffers audio frame data without DMA overflow. Low-power SleepWalking modes extend battery life in portable units.
추천
Battery-Powered Wearable Device
The ATSAMD51J18A-AU-EFP fits wearable designs because its 1.71-3.63 V operating range supports single-cell Li-Ion battery operation directly. The Cortex-M4F with FPU executes low-power sensor fusion (pedometer, heart rate, SpO2) at 120 MHz, while multiple sleep modes drop current consumption to microamps between sensor reads. Six SERCOM interfaces connect I2C sensors (accelerometer, PPG, temperature), SPI displays, and BLE companion modules. The integrated 12-bit ADC samples bioelectric signals with 1 Msps for high-fidelity capture. USB Full-Speed enables charging and firmware update over a single connector without external PHY cost.
추천
Robotics Motor Controller
The ATSAMD51J18A-AU-EFP serves as a multi-axis motor controller in robotics due to its Cortex-M4F core with DSP extensions and 120 MHz performance for field-oriented control (FOC) loops. The TCC timers generate complementary PWM outputs with dead-time insertion for 3-phase motor drives, while the Event System synchronizes ADC sampling to PWM events for precise current sensing. The 12-bit 1 Msps ADC handles multiple current-sense channels concurrently with DMA, offloading the CPU. USB Full-Speed supports PC-based tuning and real-time telemetry. Industrial -40C to +85C temperature rating suits harsh factory environments.
추천
Medical Point-of-Care Diagnostic Device
The ATSAMD51J18A-AU-EFP suits medical point-of-care devices because its Cortex-M4F with FPU processes biosensor signal data accurately while running USB-based connectivity. The 12-bit ADC at 1 Msps captures electrochemical sensor signals (glucose, blood gas) with low noise, and the ECC-protected 256 KB Flash plus 128 KB SRAM meet IEC 62304 firmware reliability expectations. Six SERCOM interfaces connect barcode scanners, displays, and external storage. The industrial temperature range supports clinical environments, and the low-power SleepWalking modes extend battery runtime in portable diagnostic units. USB Full-Speed enables LIS (Laboratory Information System) data uploads.
추천
Smart Home Edge Gateway
The ATSAMD51J18A-AU-EFP is a strong fit for smart-home edge gateways because its Cortex-M4F at 120 MHz runs local decision logic, rule engines, and protocol bridging across Zigbee, Z-Wave, WiFi, and BLE simultaneously. Six SERCOM ports interface multiple radio modules and sensors concurrently, while USB Full-Speed provides local configuration and firmware update. The 256 KB Flash accommodates TLS stacks, MQTT brokers, and protocol parsers, and the 128 KB SRAM handles message buffers without DMA overflow. Wide 1.71-3.63 V supply supports 3.3 V system rails; industrial temperature rating covers indoor and outdoor installations.
추천
추천 제품 요약
엔지니어링 참조 데이터: ATSAMD51J18A-AU-EFP — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ATSAMD51J18A-AU | ATSAMD51J19A-AU-EFP | ATSAMD51N20A-AU-EFP | ATSAMD51G18A-MFT |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-TQFP (10x10 mm) | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same | 64-TQFP (10x10 mm) - same | 48-TQFP - different footprint |
| Core | ARM Cortex-M4F @ 120 MHz | ARM Cortex-M4F @ 120 MHz | ARM Cortex-M4F @ 120 MHz | ARM Cortex-M4F @ 120 MHz | ARM Cortex-M4F @ 120 MHz |
| Flash | 256 KB | 256 KB | 512 KB | 1 MB | 256 KB |
| SRAM | 128 KB | 128 KB | 128 KB | 256 KB | 128 KB |
| USB | USB 2.0 FS with PHY | USB 2.0 FS with PHY | USB 2.0 FS with PHY | USB 2.0 FS with PHY | USB 2.0 FS with PHY |
| ADC | 12-bit, 1 Msps, 16 ch | 12-bit, 1 Msps, 16 ch | 12-bit, 1 Msps, 16 ch | 12-bit, 1 Msps, 16 ch | 12-bit, 1 Msps, 12 ch |
| Operating Voltage | 1.71 V to 3.63 V | 1.71 V to 3.63 V | 1.71 V to 3.63 V | 1.71 V to 3.63 V | 1.71 V to 3.63 V |
| GPIO Count | 51 | 51 | 51 | 51 | 37 |
| Approx. Unit Price (qty 1) | $6.85 | $6.50 | $7.80 | $8.95 | $6.20 |
주요 차별점
- Extended Flash Performance (EFP) tuning (vs ATSAMD51J18A-AU)
- Higher-density Flash in same footprint (vs ATSAMD51J19A-AU-EFP)
- 51 GPIO pins in 64-TQFP (vs ATSAMD51G18A-MFT)
- Integrated USB 2.0 Full-Speed PHY (vs STM32F401RBT6 (64-LQFP, cross-brand))
설계 노트
Place a 100 nF ceramic decoupling capacitor within 2 mm of every VDDIO and VDDIN pin, plus a single 4.7 uF bulk capacitor on VDDIN. The ATSAMD51J18A-AU-EFP integrates an LDO that derives VDDCORE from VDDIN; bypass the core pin with a 1 uF X7R capacitor. Wide-trace VDDIO/GND pours improve thermal dissipation under USB load. Verify the supply ramp time (under 50 ms) to avoid errata during cold-start initialization.
Route the 32.768 kHz low-frequency crystal traces symmetrically with ground shielding and place the load capacitors within 1 mm of the XIN32/XOUT32 pins. For the main 12 MHz crystal, use short traces with a ground guard ring; mismatched trace lengths cause duty-cycle distortion on PLL outputs. Route USB DP/DM as a 90-ohm differential pair of equal length, keeping them away from switching signals like PWM outputs to meet USB 2.0 Full-Speed signal-integrity requirements.
The ATSAMD51J18A-AU-EFP SERCOM peripheral supports I2C Fast Mode Plus (1 MHz) only when the corresponding SERCOM pad supply is 3.3 V; at 1.8 V VDDIO, fall back to I2C Fast Mode (400 kHz). For SPI peripherals above 24 MHz, use the SERCOM in master mode with clock phase/control matched to the slave device timing. Add 33 ohm series damping resistors on long SPI traces (>50 mm) to suppress ringing without exceeding the GPIO drive-strength specification.
Do not enable the USB peripheral until VBUS has stabilized and the internal 48 MHz USB clock has settled, or the USB enumeration will fail intermittently. When using the I2S peripheral, configure the frame-sync and bit-clock pins to alternate SERCOM functions before enabling the peripheral to avoid glitches. The 12-bit ADC requires a minimum acquisition time of 200 ns per channel; shorter times cause crosstalk and inaccurate readings. Use FreeRTOS tick-less idle mode to take advantage of the integrated SleepWalking controller and reduce idle current to 5 uA.
Estimated: at maximum CPU activity (120 MHz with all peripherals active), the ATSAMD51J18A-AU-EFP dissipates approximately 60 mW from a 3.3 V supply. The 64-TQFP package has theta_JA of approximately 60 C/W (JEDEC EIA/JESD51 4-layer board), yielding a junction-to-ambient temperature rise of about 3.6 C. At the 85 C industrial ambient limit, the junction reaches 88.6 C, well below the 125 C maximum. No heatsink is required for typical IoT or industrial designs; ensure adequate ground-pour area for thermal spreading.
규정 준수 정보
RoHS and REACH compliant per Microchip product page. Not AEC-Q100 qualified; for automotive applications use ATSAM D5x automotive-grade variants. Halogen-free status not explicitly stated in provided web data.
