ATTINY28V-1AU - 8-Bit AVR MCU, 2KB Flash | Microchip
부품 번호: ATTINY28V-1AU ✓ 활성ATTINY28V-1AU 개요
An 8-bit AVR microcontroller is a compact embedded-control IC that executes instructions using an AVR RISC core. Microcontrollers integrate processor logic, program memory, registers, and peripherals into one package, allowing a design to replace separate processor, memory, and interface components. The ATTINY28 family occupies the low-complexity end of the TinyAVR portfolio and is designed for straightforward control tasks rather than high-volume data processing.
The device provides 2 KB of programmable Flash, 32 general-purpose registers, a keyboard interrupt function, and an analog comparator. Its 8-bit architecture provides 32 general-purpose working registers, while the one-cycle execution capability of the AVR core supports throughput approaching 1 MIPS per megahertz. The listed 1.2 MHz operating speed makes it suitable for motor, appliance, keypad, and compact industrial-control designs that do not require a high-performance MCU.
The ATTINY28V-1AU operates across the listed 2.5 V, 3.3 V, and 5 V supply options, allowing the same controller family to support different system rails. The keyboard interrupt can reduce polling demands in matrix-keypad designs, while the analog comparator supports threshold detection, basic signal conditioning, and simple sensor-interface functions without requiring a separate comparator IC.
Typical applications include keyboard scanners, small appliance controllers, optocoupler and switch interfaces, basic motor-control logic, LED sequencing, and low-cost embedded automation modules. The 32-pin TQFP package provides more connection options than the smaller ATTINY28 packages, making it useful when several I/O lines or power-related pins are needed on a compact PCB.
Keep the clock and power rails stable, route decoupling capacitors close to the supply pins, and verify every external pull-up or pull-down value against the configured I/O source current. Before firmware transfer or production use, check the fuse configuration and application circuit against the manufacturer pin-description table so that unused pins, reset behavior, and programming connections remain consistent with the selected board revision.
This page combines the ATTINY28 family architecture, package information, application guidance, and technically relevant replacement comparisons. It also organizes pin, sourcing, lifecycle, and design questions into an engineering-focused format that supports faster component evaluation than a basic distributor listing alone.
드롭인 대체품: ATTINY28V-1AU — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ATTINY28V-1AU (동일 폼 팩터 및 풋프린트) — 차이점: Architecture, Flash Memory, Maximum Clock Frequency, Mounting Type, Package.
ATTINY28V-1AC
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ATTINY28V-1PI
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ATTINY28L-4AU
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ATTINY48-AU
✅ 드롭인가격 문의
데이터시트 보기 →ATTINY28V-1AU 최대 정격 & 전기적 특성
| Product Type | 8-bit RISC microcontroller |
| Architecture | AVR RISC |
| 최대 클록 주파수 | 1.2 MHz |
| Flash Memory | 2 KB (1K x 16 words) |
| General-Purpose Registers | 32 registers |
| Data Width | 8 bits |
| Throughput | Up to 4 MIPS |
| Supply Voltage Options | 2.5 V, 3.3 V, and 5 V |
| Peripheral Feature | Keyboard interrupt |
| Analog Feature | Analog comparator |
| 패키지 | 32-pin TQFP, 7 x 7 mm |
| 실장 유형 | Surface-mount |
| Program Memory Type | Flash |
ATTINY28V-1AU 32-pin tqfp, 7 x 7 mm 핀 구성 가이드
ATTINY28V-1AU(32-pin tqfp, 7 x 7 mm 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: ATTINY28V-1AU.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
ATTINY28V-1AU 적합 용도: 6 애플리케이션s: Matrix Keyboard Controller, Small Appliance Control, LED Sequencing and Indicators, Switch and Optocoupler Interface, Simple Threshold Sensor Interface, Compact Motor and Valve Control.
Matrix Keyboard Controller
The ATTINY28V-1AU fits matrix-keypad scanning because it combines a keyboard interrupt with 32 general-purpose registers and an 8-bit AVR processor. According to the Microchip ATTINY28 manufacturer datasheet, the interrupt can initiate a scan when a key event is detected instead of requiring continuous polling. The device's listed 1.2 MHz clock is sufficient for debounce timing and row-column scanning, while the 32-pin TQFP package provides ample connections for scanned lines and control signals. Firmware should still implement debounce, key rollover, and long-press behavior, and the PCB should reserve external pull-up or pull-down footprints so the I/O mode can be selected during development.
Small Appliance Control
The ATTINY28V-1AU is suitable for compact appliance controllers that coordinate switches, indicators, relays, and a small keypad or sensor interface. Its 2 KB of Flash provides room for compact state-machine firmware, and the 8-bit AVR RISC architecture supports practical control logic at the listed 1.2 MHz operating speed. According to the Microchip ATTINY28 manufacturer datasheet, the controller includes 32 registers, a keyboard interrupt, and an analog comparator. Use the analog comparator for simple threshold detection when a dedicated sensor interface is unnecessary, while retaining careful separation between mains-adjacent switching circuitry and low-voltage control signals in the final layout.
LED Sequencing and Indicators
For LED sequencing, status indication, and panel backlighting, the ATTINY28V-1AU provides enough I/O capability for multiple control lines without adopting a larger microcontroller. According to the Microchip ATTINY28 manufacturer datasheet, the AVR core supports throughput approaching 1 MIPS per megahertz, which is more than adequate for deterministic update rates and button-driven lighting effects. The listed 2.5 V, 3.3 V, and 5 V supply options allow selection of a system rail that matches the indicator circuitry. Design the LED paths for the intended drive current, use suitable transistor or driver stages when the total load exceeds an I/O pin's safe limit, and place bypass capacitance directly beside the controller's supply connections.
Switch and Optocoupler Interface
The ATTINY28V-1AU can supervise switches, relay-control signals, and optocoupler outputs in compact industrial or appliance electronics. Its 32-pin TQFP package exposes more I/O than smaller ATTINY28 variants, while the 8-bit processing core is sufficient to debounce inputs and implement interlocks or state transitions. According to the Microchip ATTINY28 manufacturer datasheet, the device operates at up to 1.2 MHz and includes 32 general-purpose registers. Maintain compatible logic levels between the MCU and interface components, include flyback protection for inductive loads, and keep switching-current paths physically separated from sensitive control traces to reduce coupling into the analog comparator and input circuitry.
Simple Threshold Sensor Interface
The ATTINY28V-1AU can support basic sensing functions where an on-chip comparator is adequate, such as threshold detection, simple level alarms, or monitoring an analog signal converted into a switching decision. According to the Microchip ATTINY28 manufacturer datasheet, the device includes an analog comparator alongside its 8-bit AVR core and 2 KB of programmable Flash. This avoids requiring a separate comparator in straightforward designs, although input range, offset behavior, noise, and response time still need to be evaluated against the sensor signal. Keep sensitive analog routing short, provide a stable reference arrangement, and avoid routing high-current switching paths beneath the comparator input.
Compact Motor and Valve Control
The ATTINY28V-1AU can serve as the supervisory controller for a small motor, solenoid, stepper sequence, or valve system where the main power device is driven externally. Its listed 1.2 MHz clock supports timing loops and sequence management, while the 32-pin TQFP package provides a practical balance between I/O access and board area. According to the Microchip ATTINY28 manufacturer datasheet, the AVR architecture executes many instructions in one clock cycle. Add external transistor or MOSFET drive stages rather than driving inductive loads directly from an I/O pin, include flyback protection, and validate timing under worst-case supply voltage and motor-load conditions before production use.
엔지니어링 참조 데이터: ATTINY28V-1AU — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ATTINY28V-1AC | ATTINY28V-1PI | ATTINY28L-4AU | ATTINY48-AU |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 32-TQFP (7x7 mm) | 32-TQFP (7x7 mm) | TQFP-32 | TQFP-32 | TQFP-32 |
| Architecture | AVR RISC, 8-bit | AVR RISC, 8-bit | AVR RISC, 8-bit | AVR RISC, 8-bit | AVR RISC, 8-bit |
주요 차별점
- Broader listed supply-voltage selection than the 1.8 V ATTINY28V-1PI option (vs ATTINY28V-1PI)
- Lower listed clock rate provides a distinct timing choice for ATTINY28L designs (vs ATTINY28L-4AU)
- Direct family match retains the documented 2 KB Flash and keyboard-interrupt feature set (vs ATTINY28V-1AC)
설계 노트
Place the controller's decoupling capacitor immediately beside the supply and ground pins, with a short, low-inductance return path. Keep programming and debug signal traces accessible and away from switching nodes. Because the ATTINY28V-1AU uses a 32-pin TQFP footprint, inspect the land pattern against the manufacturer package drawing and verify pin 1 orientation during PCB assembly.
Design the power rail for the voltage option selected for the finished system, including 2.5 V, 3.3 V, or 5 V operation. Check the clock and analog functions at the minimum rail voltage rather than relying only on nominal supply values. Add local bypass capacitance, avoid sharing high-current return paths with sensitive input traces, and confirm reset behavior during power ramp conditions.
Do not assume that every ATTINY28 suffix has identical timing or voltage limits. Before substituting ATTINY28V-1AC, ATTINY28V-1PI, ATTINY28L-4AU, or ATTINY48-AU, compare clock behavior, supply range, memory requirements, peripheral functions, reset pins, and programming connections against the manufacturer documentation. A matching TQFP outline alone does not prove functional interchangeability.
For matrix-keypad or switch inputs, select pull-up or pull-down resistors according to the configured I/O mode and keep traces short enough to limit capacitive noise. Firmware should debounce contacts and avoid treating a brief contact event as a valid key until the timing criteria are met. Route clock and sensitive analog lines away from relay, motor, and LED-switching currents.
규정 준수 정보
Compliance status requires confirmation from the manufacturer's current material-declaration documentation for the exact ordering suffix.