ATXMEGA32D4-CU - 32MHz 32KB Flash MCU | Microchip
부품 번호: ATXMEGA32D4-CU ✓ 활성ATXMEGA32D4-CU 개요
An AVR XMEGA microcontroller is an 8/16-bit embedded-control IC based on the enhanced AVR RISC architecture. Within the product hierarchy, it is a microcontroller, embedded processor, and programmable controller designed for low-power industrial, consumer, communications, and real-time control systems. Unlike a general-purpose desktop processor, it combines flash program memory, data EEPROM, SRAM, event handling, timers, and serial communications on one integrated device.
The ATXMEGA32D4 family provides 32 KB of in-system-programmable flash with read-while-write operation and a dedicated 4 KB boot-code section. Its 1 KB EEPROM supports nonvolatile parameter storage, while 4 KB of SRAM accommodates working data and interrupt-intensive control tasks. A 16-bit real-time counter and four 16-bit timer/counters provide deterministic timing, compare, and PWM functions for motor, lighting, and industrial automation systems.
Its event-system architecture allows hardware routing between peripherals, reducing the processor intervention required for time-critical signal relationships. The programmable multilevel interrupt controller and two USARTs support asynchronous serial communication, while the two TWI interfaces support connected peripherals over a two-wire bus. The combination of 34 I/O lines and multiple communication peripherals makes the device useful where compactness and peripheral integration are important.
Typical uses include industrial sensor controllers, building-automation nodes, compact communication equipment, motor-control helpers, low-power embedded products, and control systems requiring deterministic event handling. The ATXMEGA32D4 family is also suitable for general AVR-based embedded development when more timing and communication resources are required than a basic 8-bit AVR provides.
A key design consideration is the 49-VFBGA footprint, which is compact but demands careful PCB layout, fine-pitch assembly, and inspection. Designers must follow the manufacturer's package drawing and pin-assignment documentation exactly, provide suitable decoupling, and verify the operating voltage configuration before programming the device. The supplied search data includes differing voltage-range summaries, so the electrical limits should be confirmed against the manufacturer datasheet for the selected device.
This page consolidates the verified manufacturer and distributor information, identifies same-family drop-in options, and adds practical application guidance, comparison data, and design cautions that are not presented as a complete substitute for the manufacturer datasheet. Verified pricing, detailed pin assignments, lifecycle guarantees, and package drawings should be confirmed with the cited sources before production release.
드롭인 대체품: ATXMEGA32D4-CU — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ATXMEGA32D4-CU (동일 폼 팩터 및 풋프린트) — 차이점: EEPROM, Interrupt Controller, Package.
ATXMEGA64D4-CU
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →ATXMEGA128D4-CU
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
ATXMEGA128A4U-CU
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ATXMEGA32D4-CU 최대 정격 & 전기적 특성
| Microcontroller Family | AVR XMEGA D4 |
| Architecture | 8/16-bit AVR enhanced RISC |
| Maximum Clock Speed | 32 MHz |
| Program Memory | 32 KB Flash (16K x 16) |
| Boot Code Section | 4 KB |
| Flash Feature | In-system programmable with read-while-write capability |
| EEPROM | 1 KB |
| SRAM | 4 KB |
| General-Purpose I/O | 34 lines |
| Event System | 4 channels |
| Interrupt Controller | Programmable multilevel interrupt controller |
| Real-Time Counter | 16-bit |
| Timer/Counter Channels | 4 flexible 16-bit timer/counters with compare and PWM channels |
| UART Channels | 2 USARTs |
| TWI Channels | 2 two-wire serial interfaces |
| Supply Voltage Options | 1.8 V / 2.5 V / 3.3 V |
| 동작 온도 | -40°C to +85°C |
| 패키지 | 49-VFBGA (5 x 5 mm) |
| 실장 유형 | Surface Mount |
| 수명 주기 상태 | Active |
| RoHS 상태 | Compliant |
ATXMEGA32D4-CU 49-vfbga (5 x 5 mm) 핀 구성 가이드
ATXMEGA32D4-CU(49-vfbga (5 x 5 mm) 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: ATXMEGA32D4-CU.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
ATXMEGA32D4-CU 적합 용도: 6 애플리케이션s: Industrial Sensor and Condition Monitoring, Building Automation and Lighting Control, Communication Equipment and Protocol Bridge, Low-Power Connected Controller, Motor Control and PWM Actuation, Real-Time Control and Event Processing.
Industrial Sensor and Condition Monitoring
The ATXMEGA32D4-CU fits distributed industrial monitoring because its 34 general-purpose I/O lines can connect multiple digital inputs and outputs while two TWI interfaces support addressable sensors. According to the Microchip XMEGA D4 datasheet, the device operates at up to 32 MHz and includes 1 KB of EEPROM for calibration constants, fault counters, and configuration records. The four-channel event system can route peripheral events directly, reducing processor work in time-critical acquisition loops. Designers should keep analog conditioning and surge protection outside the MCU, use the available timer channels for accurate sampling, and confirm the final 49-VFBGA pinout before routing.
추천
Building Automation and Lighting Control
The ATXMEGA32D4-CU is suitable for compact building-automation nodes because it combines 34 I/O lines, four 16-bit timer/counters with compare and PWM channels, two USARTs, and two TWI interfaces in one 49-VFBGA device. According to the Microchip XMEGA D4 datasheet, the event system and programmable multilevel interrupts can coordinate actuator events efficiently. PWM channels can control dimmable lighting or motor actuators, while TWI can connect sensors and communication transceivers. In a real installation, isolated field interfaces, proper flyback protection, fail-safe states, and validated low-voltage timing should be included rather than treating the microcontroller pins as direct power-stage drivers.
추천
Communication Equipment and Protocol Bridge
The ATXMEGA32D4-CU can support compact protocol-conversion or embedded communications equipment using its two USARTs and two TWI interfaces. According to the Microchip XMEGA D4 datasheet, the microcontroller provides 32 KB of read-while-write Flash, 4 KB of SRAM, and a programmable interrupt controller for responsive serial handling. Its 32 MHz processing rate supports framing, buffering, basic protocol translation, and local diagnostics without a separate processor. The design must budget SRAM carefully for simultaneous receive buffers, isolate external communication lines, and validate timing at the target bus voltage. Firmware updates should account for read-while-write behavior and the dedicated 4 KB boot section.
추천
Low-Power Connected Controller
The ATXMEGA32D4-CU supports low-power connected products that periodically measure data, communicate locally, and return to a reduced-power state. According to the Microchip XMEGA D4 datasheet, the family combines 32 KB of Flash, 1 KB of EEPROM, 4 KB of SRAM, and a four-channel event system in a compact 5 x 5 mm package. EEPROM can retain calibration or network information across resets, while the 16-bit real-time counter and timer/counters support periodic wake-up and measurement timing. Power-budget calculations must include active and sleep currents from the manufacturer datasheet, which were not included in the supplied search data, and must account for leakage through attached sensors and communication interfaces.
추천
Motor Control and PWM Actuation
The ATXMEGA32D4-CU is well suited to supervisory motor-control and actuator systems because it provides four flexible 16-bit timer/counters with compare and PWM channels alongside 34 I/O lines. According to the Microchip XMEGA D4 datasheet, the 16-bit real-time counter and hardware event system support deterministic sequencing across multiple timing functions. The MCU can generate command and PWM signals, monitor position or limit inputs, and coordinate emergency states while leaving power conversion and high-current drive stages to external circuitry. Engineers must include suitable gate drivers, current sensing, overcurrent handling, and protection for inductive loads, and should verify timer outputs against the exact device pin mapping.
추천
Real-Time Control and Event Processing
The ATXMEGA32D4-CU fits real-time control tasks where peripheral timing must remain deterministic under interrupt load because it includes a four-channel event system, programmable multilevel interrupts, a 16-bit real-time counter, and four 16-bit timer/counters. According to the Microchip XMEGA D4 datasheet, this event-routing architecture reduces the need for software polling and allows precise relationships between timers and communication peripherals. Its 32 MHz core provides useful computation margin for control calculations, while 4 KB of SRAM supports working state. The 49-VFBGA footprint still requires careful escape routing, clean grounding, and validated decoupling to prevent timing or analog-noise problems.
추천
추천 제품 요약
엔지니어링 참조 데이터: ATXMEGA32D4-CU — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ATXMEGA64D4-CU | ATXMEGA128D4-CU | ATXMEGA128A4U-CU |
|---|---|---|---|---|
| Package | 49-VFBGA (5 x 5 mm) | 49-VFBGA (5 x 5 mm) | 49-VFBGA (5 x 5 mm) | 49-VFBGA (5 x 5 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Maximum Clock Speed | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Flash Memory | 32 KB | 64 KB | 128 KB | 128 KB |
주요 차별점
- Balanced embedded-memory configuration (vs ATXMEGA64D4-CU)
- Smaller Flash footprint than the 128 KB same-family option (vs ATXMEGA128D4-CU)
- Same compact 49-VFBGA family footprint (vs ATXMEGA128A4U-CU)
설계 노트
The 49-VFBGA footprint requires close attention to the manufacturer land pattern, ball numbering, solder-mask definition, and assembly capability. Verify every power and ground connection against the device package drawing rather than inferring positions from a generic BGA library. Provide local decoupling at each supply pin, route high-current returns without splits, and reserve programming or recovery access where the system permits it. Because the complete ball table was not supplied in the verified data, no pin-level routing recommendation should be treated as authoritative until the manufacturer package drawing is reviewed.
Design the supply around the exact operating voltage configuration confirmed in the manufacturer datasheet; the retrieved listings provide inconsistent summaries of 1.6-3.6 V, 2.7-3.6 V, and 1.8 V/2.5 V/3.3 V options. Use a regulator with appropriate transient response for the 32 MHz core and ensure brownout and power-up behavior meet the firmware requirements. Keep analog and communication loads on filtered branches when their current transients could disturb MCU rails, and calculate worst-case supply droop with peripheral loading rather than the MCU's nominal current alone.
Place decoupling capacitance close to each VCC and ground ball using the shortest possible current-loop path. Route the 32 MHz clock carefully, keep switching-node and high-current actuator paths away from the MCU and sensitive inputs, and provide a low-impedance ground reference for timer inputs and serial interfaces. Although the XMEGA event system can connect peripherals internally, external signal conditioning and protection still determine practical noise immunity. Perform signal-integrity and EMC checks on the completed layout rather than relying only on schematic inspection.
Do not treat same-family parts as automatically interchangeable merely because their memory capacities differ. Changing from ATXMEGA32D4-CU to a larger-Flash D4 device can alter flash organization, boot behavior, code addresses, linker output, erase timing, and application constraints. Likewise, a 49-VFBGA package does not establish pin compatibility by itself. Compare the exact ordering code, ball assignment, electrical limits, peripheral configuration, programming interface, and package drawing, then rerun firmware and hardware validation before substituting any listed alternative.
규정 준수 정보
RoHS compliance is explicitly stated in the verified Master Electronics result. No verified REACH, halogen-free, conflict-minerals, or automotive qualification statements were supplied. AEC-Q100 is marked not_applicable because this is a general-purpose MCU and no automotive qualification was identified.
