BTH62004ESAXUMA1 - 4-Ch 200mΩ 48V Smart High-Side Switch | Infineon
부품 번호: BTH62004ESAXUMA1 ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $3.42 | $3.42 |
| 10 | $3.08 | $30.80 |
| 100 | $2.74 | $274.00 |
| 500 | $2.45 | $1,225.00 |
| 1,000 | $2.18 | $2,180.00 |
BTH62004ESAXUMA1 개요
A high-side smart switch is a type of power distribution switch that sits between the supply rail and the load, integrating the power MOSFET, gate driver, protection circuitry, and diagnostic feedback into one IC. High-side switches belong to the broader power management semiconductor category, which also includes low-side switches, half-bridges, and H-bridges. Compared with discrete MOSFETs plus fuses, a smart high-side switch reduces PCB area, eliminates the need for external protection components, and provides the ECU with real-time load-current and fault-status information through the IS pin.
Key features include 200 mΩ typical RDS(on) per channel at 25 °C, 1 A nominal load current per channel, integrated charge pump for full N-channel drive, current sense ratio with high accuracy, and programmable restart behavior after fault clearing. The PG-TSDSO-24-21 package uses an exposed thermal pad that reduces junction-to-PCB thermal resistance, allowing the four channels to operate at full current without external heatsinking in typical automotive body-control environments.
The architecture combines an N-channel vertical power MOSFET with a charge pump, logic interface, and dedicated protection/diagnosis state machine per channel. The device is optimized for 48 V systems but tolerates load-dump transients above 60 V, making it suitable for both 24 V and 48 V board nets in commercial vehicles, mild hybrids, and 48 V zonal architectures.
Typical applications include 48 V body-control modules driving LED arrays, small motors, and resistive heaters, as well as zonal ECUs in 48 V mild-hybrid vehicles. The four independent channels make it suitable for driving four separate loads from one compact IC, reducing BOM count and ECU footprint.
When designing with the BTH62004ESAXUMA1, ensure the exposed pad is soldered to a sufficient copper pour to keep junction temperature within the -40 °C to +150 °C operating range. The IS pin must be connected to a microcontroller ADC through a recommended filter network for accurate current-sense readings, and unused channels should be tied to GND with IN off.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.
드롭인 대체품: BTH62004ESAXUMA1 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: BTH62004ESAXUMA1 (동일 폼 팩터 및 풋프린트) — 차이점: Package, Topology, Operating Temperature Range, Number of Channels, Protection Features.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
BTT62004ESAXUMA1
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
BTH60801EPLXUMA1
✅ 드롭인✓ 재고 있음
$1.74 / 개
데이터시트 보기 →BTH62004ESAXUMA1 최대 정격 & 전기적 특성
| Product Type | Smart High-Side Power Switch |
| Family | PROFET+ 48V |
| Number of Channels | 4 |
| 토폴로지 | 4 x High-Side (1:1) |
| On-State Resistance (RDS(on)) | 200 mΩ typical per channel |
| Nominal Load Current per Channel | 1 A |
| Supply Voltage Range | Up to 54 V |
| Load-Dump Tolerance | 60 V (transient, per datasheet) |
| Power Transistor Technology | N-channel vertical power MOSFET with charge pump |
| Current Sense Diagnosis | Yes (analog IS pin) |
| Protection Features | Over-temperature, over-voltage, short-circuit, reverse battery |
| 동작 온도 범위 | -40 °C to +150 °C junction |
| 패키지 | PG-TSDSO-24-21 (exposed pad) |
| 실장 유형 | Surface Mount |
| Automotive Qualification | AEC-Q100 qualified |
BTH62004ESAXUMA1 핀 구성
| 핀 1 | OUT1 — Channel 1 high-side output to load |
| 핀 2 | OUT2 — Channel 2 high-side output to load |
| 핀 3 | GND — Ground |
| 핀 4 | OUT3 — Channel 3 high-side output to load |
| 핀 5 | OUT4 — Channel 4 high-side output to load |
| 핀 6 | GND — Ground |
| 핀 7 | VBB — Battery supply (48 V nominal) |
| 핀 8 | IS — Current sense / diagnostic output |
| 핀 9 | NC — Not connected (per datasheet) |
| 핀 10 | IN4 — Channel 4 logic input |
| 핀 11 | IN3 — Channel 3 logic input |
| 핀 12 | NC — Not connected (per datasheet) |
| 핀 13 | IN2 — Channel 2 logic input |
| 핀 14 | IN1 — Channel 1 logic input |
| 핀 15 | NC — Not connected (per datasheet) |
| 핀 16 | GND — Ground |
| 핀 17 | NC — Not connected (per datasheet) |
| 핀 18 | NC — Not connected (per datasheet) |
| 핀 19 | NC — Not connected (per datasheet) |
| 핀 20 | NC — Not connected (per datasheet) |
| 핀 21 | NC — Not connected (per datasheet) |
| 핀 22 | NC — Not connected (per datasheet) |
| 핀 23 | NC — Not connected (per datasheet) |
| 핀 24 | NC — Not connected (per datasheet) |
일반적인 애플리케이션
BTH62004ESAXUMA1 적합 용도: 6 애플리케이션s: 48V Zonal ECU Body Loads, Automotive LED Lighting Drivers, 48V Resistive Heater Control, Solenoid and Valve Drivers, Small DC Motor Switching (On/Off), 48V Auxiliary Load Switching.
48V Zonal ECU Body Loads
The BTH62004ESAXUMA1's four independent 200 mΩ high-side channels fit 48 V zonal ECU designs where one IC drives multiple body loads (LEDs, mirror adjusters, seat heaters) from a compact footprint. Each channel's 1 A rating covers typical 48 V body-electronics loads, and the 54 V nominal / 60 V transient rating tolerates 48 V mild-hybrid load-dump events. Integrated current sense via the IS pin lets the host MCU perform open-load and short-circuit diagnostics without external shunt resistors, simplifying the BOM for high-volume zonal modules.
추천
Automotive LED Lighting Drivers
The BTH62004ESAXUMA1 drives four independent LED strings in daytime running lights, position lamps, or interior lighting modules from a 48 V rail. Each channel's 200 mΩ RDS(on) and 1 A capacity handle multi-LED strings up to roughly 15 W per channel, while the integrated PWM-capable input enables dimming via the IN pin. The exposed-pad PG-TSDSO-24-21 package keeps junction temperature low enough to omit an external heatsink, which is critical for space-constrained lamp housings.
추천
48V Resistive Heater Control
In seat heaters, mirror heaters, and steering-wheel heaters, the BTH62004ESAXUMA1 switches four resistive heating elements with software-controlled PWM. The device's N-channel vertical MOSFET with charge pump provides full enhancement-mode drive, minimizing conduction losses across the heater's operating range. Integrated over-temperature protection and IS-pin diagnostics enable the ECU to detect heater degradation or short circuits, which is essential for meeting automotive functional-safety requirements in heater circuits.
추천
Solenoid and Valve Drivers
The BTH62004ESAXUMA1 drives four 48 V solenoids or proportional valves in transmission, EGR, or active-suspension systems. Each channel's integrated inductive-load clamp eliminates the need for external freewheeling diodes, reducing PCB area and BOM cost. The 60 V transient tolerance handles the back-EMF spikes generated when 48 V solenoid valves de-energize, and the AEC-Q100 qualification supports use in safety-relevant powertrain subsystems.
추천
Small DC Motor Switching (On/Off)
For simple on/off control of small 48 V DC motors (window lift, sunroof, washer pump), the BTH62004ESAXUMA1 provides protected high-side switching with stall-current detection via the IS pin. The ECU can identify a stalled or jammed motor by monitoring the analog current-sense output, enabling predictive maintenance. For bidirectional motor control, pair the BTH62004ESAXUMA1 with a companion half-bridge or H-bridge driver such as the TLE94110ESXUMA1.
추천
48V Auxiliary Load Switching
The BTH62004ESAXUMA1 switches miscellaneous 48 V auxiliary loads (USB chargers, DC-DC converter enables, auxiliary pumps) from a body or zonal ECU. Each channel's logic-level IN pin interfaces directly to 3.3 V or 5 V MCU GPIOs without external level shifters, simplifying the schematic. The exposed-pad PG-TSDSO-24-21 package and 1 A per channel rating support up to four independent auxiliary rails in a single 24-pin footprint, ideal for high-density 48 V body modules.
추천
추천 제품 요약
엔지니어링 참조 데이터: BTH62004ESAXUMA1 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | BTT62004ESAXUMA1 | BTH60801EPLXUMA1 |
|---|---|---|---|
| Brand | Infineon | Infineon | Infineon |
| Package | PG-TSDSO-24-21 | PG-TSDSO-24-21 | PG-TSDSO-24-21 |
| Number of Channels | 4 | 4 | 1 |
| RDS(on) per Channel | 200 mΩ | 200 mΩ | 200 mΩ |
| Nominal Load Current per Channel | 1 A | 1 A | 1 A |
| Nominal Supply Voltage | 48 V (54 V max) | 24 V (28 V max) | 48 V (54 V max) |
| Current Sense Diagnosis | Yes (IS pin) | Yes (IS pin) | Yes (IS pin) |
| Automotive Qualification | AEC-Q100 | AEC-Q100 | AEC-Q100 |
| Family | PROFET+ 48V | PROFET+ 24V | PROFET+ 48V |
주요 차별점
- Quad 200 mΩ channels in one 24-pin exposed-pad package (vs BTH60801EPLXUMA1)
- 48 V board-net optimized with 60 V transient tolerance (vs BTT62004ESAXUMA1)
- Integrated IS current-sense pin across all 4 channels (vs Discrete N-channel MOSFET + sense resistor)
설계 노트
Estimated: at full load on all four channels (4 × 1 A = 4 A total) with VBB = 48 V and load drop = 24 V, each channel dissipates P = I² × R = 1² × 0.2 = 0.2 W, for 0.8 W total. The PG-TSDSO-24-21 package's exposed pad must be soldered to at least 1 cm² of 2 oz copper on each PCB layer to stay within the 150 °C junction limit. Without the exposed pad, junction temperature would exceed limits under continuous full-channel load.
Place the VBB decoupling capacitor (≥ 100 nF ceramic, low-ESR) within 5 mm of the VBB pin to suppress voltage transients during channel turn-off of inductive loads. The exposed pad must use thermal vias (typically 9 × 0.3 mm vias) to inner-layer copper planes for optimal heat spreading. Keep high-current OUT traces short and use wide copper pours (≥ 2 mm) to minimize voltage drop and parasitic inductance that can stress the integrated clamp.
Do not float unused channels - tie their IN pins to GND to keep the output MOSFET in the high-impedance state and avoid quiescent-current draw from the gate charge pump. The IS pin shares its output among all four channels; the MCU must time-multiplex ADC sampling to read each active channel separately. Exceeding 54 V on VBB for extended periods can trigger the over-voltage protection latch, requiring a power cycle to reset.
규정 준수 정보
AEC-Q100 qualified per Infineon PROFET+ 48V family datasheet. RoHS and REACH compliant; lead-free and halogen-free per automotive-grade product family standards.
