C8051F313 - 25 MHz Mixed-Signal 8051 MCU | Silicon Labs
부품 번호: C8051F313 ✓ 활성C8051F313 개요
A mixed-signal microcontroller integrates digital control, analog measurement, and communications in one device. The C8051F313 belongs to the C8051 family of 8-bit MCUs, combining an embedded 8051-compatible processing core with ADC, comparator, timer, and communication peripherals. This hierarchy places it within the broader embedded-control and power-management IC categories used in industrial sensing, instrumentation, and compact control systems.
Key features include a 25 MHz pipelined 8051-compatible core, 8 kB of Flash for in-system programming, and 1.25 kB of internal RAM. Its analog subsystem includes a 10-bit ADC with 17 channels and a maximum sampling rate of 200 ksps, plus two comparators for threshold detection and signal conditioning. Four 16-bit timers support timing, waveform generation, and periodic control tasks.
The device integrates an in-system, full-speed, non-intrusive debug interface and on-chip power-on reset according to the manufacturer product information. The C8051F31x family is positioned for compact embedded products that need mixed-signal measurement without a separate analog device. Additional communication interfaces are listed by Silicon Labs, but their individual types are not identified in the supplied source data.
Typical applications include industrial sensor nodes, analog measurement boards, compact motor and process controllers, communication modules, and test equipment. The 200 ksps ADC supports sampled analog monitoring, while the 17 GPIO and four timers allow peripheral control, timing, and external signal acquisition within one device.
A key design consideration is that the exposed-pad QFN footprint requires careful PCB layout and thermal management. Follow the manufacturer's land-pattern and exposed-pad connection guidance, place bypass capacitors close to the supply pins, and verify the required operating and storage voltage limits against the full datasheet before layout release.
This page consolidates manufacturer specifications, distributor pricing, pin-package details, and drop-in replacement guidance into one engineering-focused reference. It also identifies the parameter data that remains unavailable in the supplied sources, allowing procurement and design decisions to be traced to verified product information.
드롭인 대체품: C8051F313 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: C8051F313 (동일 폼 팩터 및 풋프린트) — 차이점: Package, ADC Resolution, RAM, Timers, Core Architecture.
C8051F311-GM
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
C8051F326-GMR
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
C8051F312-GM
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
C8051F314-GM
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
C8051F315-GM
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
C8051F313 최대 정격 & 전기적 특성
| Core | 8051-compatible, 25 MHz |
| Maximum CPU Performance | 25 MIPS |
| Program Memory | 8 kB Flash (8K x 8) |
| RAM | 1.25 kB (1.25K x 8) |
| ADC Resolution | 10 bit |
| ADC Channels | 17 |
| ADC Sampling Rate | 200 ksps |
| Comparators | 2 |
| Timers | 4 x 16-bit |
| GPIO | 25 pins |
| 패키지 | 28-pin QFN, 5 x 5 mm |
| Package Type | 28-VFQFN with exposed pad |
| 실장 유형 | Surface mount |
| Debug Interface | In-system, full-speed, non-intrusive debug |
| Power-On Reset | On-chip |
| Clock Speed | 25 MHz |
| RoHS Compliance | Compliant |
| REACH Compliance | Compliant |
C8051F313 28-vfqfn with exposed pad 핀 구성 가이드
C8051F313(28-vfqfn with exposed pad 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: C8051F313.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
C8051F313 적합 용도: 6 애플리케이션s: Industrial Sensor Node, Compact Analog Measurement Board, Process Control and Valve Controller, Communication Module Interface Controller, Battery-Powered Data Logger, Test and Measurement Front End.
Industrial Sensor Node
The C8051F313 fits compact industrial sensor nodes because its 10-bit ADC provides 17 acquisition channels at up to 200 ksps while the 25 MHz core handles sampling control and local processing. Its 25 GPIO pins can support discrete sensors, digital inputs, and actuator-control signals without a large external peripheral controller. Four 16-bit timers provide periodic measurement, debouncing, and output-timing resources. The device also includes on-chip Power-On Reset and in-system debugging, which simplifies deterministic startup and field firmware maintenance.
추천
Compact Analog Measurement Board
The C8051F313 is appropriate for a dedicated analog measurement board requiring several sensor inputs and modest digital processing. Its 17-channel, 10-bit ADC samples at up to 200 ksps, allowing the controller to acquire multiple analog inputs and apply filtering or threshold decisions. The four 16-bit timers can pace conversions and trigger events, while the 25 available GPIO pins handle range selection or instrumentation control. Firmware can use 8 kB of Flash for calibration tables and measurement routines.
추천
Process Control and Valve Controller
The C8051F313 suits compact process-control loops where analog measurements, digital setpoints, and timed outputs must be handled locally. The 10-bit ADC can monitor a pressure or level signal, and its four 16-bit timers support proportional-integral control timing, sampling intervals, and valve-actuator updates. With 25 GPIO pins and 1.25 kB of RAM, the controller can maintain state for filtering and simple control loops. Its 8 kB Flash capacity is appropriate when the application does not require a large communications stack.
추천
Communication Module Interface Controller
The C8051F313 can act as the embedded controller around a communication module because its 8051-compatible core executes at 25 MHz and the manufacturer describes additional communication interfaces on the device. Its 25 GPIO pins allow module reset, mode selection, and status monitoring, while the four 16-bit timers support frame timing or host-interface timeouts. The 10-bit, 17-channel ADC is useful for supply, bias, or diagnostic measurements. Firmware capacity must remain within 8 kB Flash unless the design is revised.
추천
Battery-Powered Data Logger
The C8051F313 is appropriate for a battery-powered data logger when low power is prioritized and the measurement rate is moderate. Its on-chip Power-On Reset supports repeatable startup, while the ADC can capture sensor values at up to 200 ksps when higher-rate sampling is needed. Timers can schedule periodic logging, and 1.25 kB of RAM accommodates short acquisition buffers. However, the minimum operating voltage, quiescent current, and analog accuracy are not quantified in the supplied data and must be checked before selecting the device for a power-limited design.
추천
Test and Measurement Front End
The C8051F313 can serve as the control front end of a compact test or measurement system. Its 17 ADC channels provide flexible analog input multiplexing, and the 25 MHz core can execute acquisition sequencing and limit checking within 8 kB of Flash. Four 16-bit timers offer accurate interval generation for stimulus timing, while 25 GPIO pins support trigger routing and instrument mode control. The in-system debug interface accelerates firmware development, although accuracy, reference voltage, and calibration specifications require review in the complete datasheet.
추천
추천 제품 요약
엔지니어링 참조 데이터: C8051F313 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | C8051F311-GM | C8051F326-GMR | C8051F312-GM | C8051F314-GM | C8051F315-GM |
|---|---|---|---|---|---|---|
| Package | QFN-28 (5x5 mm) | QFN-28 (5x5 mm) | QFN-28 (5x5 mm) | QFN-28 (5x5 mm) | QFN-28 (5x5 mm) | QFN-28 (5x5 mm) |
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
주요 차별점
- Verified 17-channel ADC without a separate analog package (vs C8051F311-GM)
- Exact 8 kB Flash fit for controlled firmware sizing (vs C8051F311-GM)
- Documented same-family replacement path (vs C8051F326-GMR)
설계 노트
Use the manufacturer 28-VFQFN exposed-pad land pattern rather than a generic 28-pin QFN footprint. The exposed pad is a thermal and electrical connection and must be tied to the appropriate power or ground plane exactly as directed by the datasheet. Confirm via the manufacturer drawing that the package suffix changes only ordering or temperature information rather than land geometry.
Place the required bypass capacitors directly beside the VDD and ground connections, with the shortest possible return path. Because the supplied excerpt does not state the input-voltage range, regulator configuration, or internal supply requirements, do not select external regulators or capacitor values until the complete electrical specifications and reference schematic have been reviewed. Verify startup behavior against the on-chip Power-On Reset requirements.
Route analog inputs away from switching nodes and high-current outputs, and provide a quiet ground path for the ADC and comparators. The 10-bit ADC is intended for compact mixed-signal measurement, but its usable accuracy still depends on reference-voltage quality, source impedance, acquisition timing, and layout. These analog parameters are not quantified in the retrieved excerpt, so the full datasheet's acquisition network and reference recommendations are required.
Do not treat the base family name C8051F313 as a complete orderable part number. The verified distributor results identify orderable suffixes including C8051F313-GM and C8051F313-GMR, and the $2.2374 LCSC price applies to the -GMR variant. Confirm the exact suffix, temperature grade, pinout, and reel orientation before ordering; suffix differences can change grade, packaging, or marking.
규정 준수 정보
RoHS and REACH compliance are reported in the supplied ETEI comparison material. The device is an industrial MCU rather than an AEC-Q100-qualified automotive device in the supplied data; lead-free, halogen-free, and conflict-minerals status are not stated.
