C8051F575-IM - 50MHz 16KB Flash 8-Bit MCU | Silicon Labs
부품 번호: C8051F575-IM ✓ 활성C8051F575-IM 개요
An 8-bit microcontroller is a compact embedded-processing component that combines a CPU core, program and data memory, peripherals, and communication interfaces on one integrated circuit. Within the semiconductor hierarchy, the C8051F575-IM belongs to the 8051 CISC family of microcontrollers, combining general-purpose control with automotive networking and analog-measurement functions. Its 50 MIPS execution capability supports responsive control loops while retaining the low-cost, deterministic characteristics traditionally associated with 8-bit embedded systems.
Key features include 16 KB of Flash program memory, 2.25 KB of data RAM, a 50 MHz maximum clock, and integrated CAN and LIN serial interfaces. The device also provides mixed-signal conversion resources, including programmable-gain inputs and throughput as high as 200 ksps. Its 1.8 V to 5.25 V operating range supports both low-voltage portable equipment and conventional 5 V industrial or automotive electronics. AEC-Q100 qualification identifies the C8051F575-IM for automotive-grade applications.
The mixed-signal architecture allows analog sensing and digital control to coexist in the same design. Programmable gain increases the usable dynamic range for low-level sensor inputs, while the data-dependent windowed interrupt generator helps software respond to defined signal conditions. The 8051-compatible CISC architecture provides straightforward instruction execution and broad familiarity among industrial-control engineers. Flash memory supports field-programmable firmware, which is useful for configuration changes and product maintenance without adding external program-memory devices.
Typical applications include automotive body and powertrain control modules, industrial motor controllers, CAN- or LIN-connected sensor nodes, building-control equipment, and compact embedded data-acquisition systems. Its 40-QFN package reduces board area compared with larger leaded packages, while the exposed pad provides a practical thermal path on multilayer PCBs. The combination of CAN and LIN connectivity is especially useful in vehicle and industrial networks that use deterministic serial protocols for distributed modules.
When laying out a C8051F575-IM board, follow the manufacturer pin-assignment table for the 40-QFN footprint and connect the exposed thermal pad to the intended ground or thermal plane. Provide clean local decoupling at the supply pins, reserve programming and debug access, and verify signal levels against the selected operating voltage. Avoid routing sensitive analog inputs next to high-current switching paths, and account for power dissipation at the highest expected ambient temperature.
This product page combines the C8051F575-IM electrical identity, family-level drop-in alternatives, package information, application guidance, and design considerations in a concise engineering reference. It also clarifies the practical differences between the industrial-tube ordering code, the automotive-qualified configuration, and neighboring C8051F57x devices.
드롭인 대체품: C8051F575-IM — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: C8051F575-IM (동일 폼 팩터 및 풋프린트).
C8051F574-IM
✅ 드롭인가격 문의
데이터시트 보기 →C8051F571-IM
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
C8051F569-IM
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
C8051F509-IM
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
C8051F568-IM
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
C8051F575-IM 최대 정격 & 전기적 특성
| Microcontroller Family | C8051F57x |
| Processor Core | 8051-compatible 8-bit CISC |
| 최대 클록 주파수 | 50 MHz |
| Execution Speed | 50 MIPS |
| Program Memory | 16 KB Flash |
| Program Memory Organization | 16K x 8 bits |
| Data RAM | 2.25 KB |
| Data RAM Organization | 2.25K x 8 bits |
| Supply Voltage Range | 1.8 V to 5.25 V |
| Supported Supply Configurations | 2.5 V, 3.3 V, and 5 V |
| Automotive Network Interfaces | CAN and LIN |
| Analog Conversion Throughput | Up to 200 ksps |
| ADC Accuracy | ±1 LSB INL |
| Analog Input Feature | Programmable gain |
| 패키지 | 40-QFN (6 x 6 mm) |
| 핀 수 | 40 pins |
| Package Type | QFN with exposed pad |
| 실장 유형 | Surface mount |
| Order Code Packaging | Tube |
| Automotive Qualification | AEC-Q100 |
| RoHS 상태 | Compliant |
C8051F575-IM qfn with exposed pad 핀 구성 가이드
C8051F575-IM(qfn with exposed pad 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: C8051F575-IM.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
C8051F575-IM 적합 용도: 6 애플리케이션s: Automotive Body Control Module, CAN-Connected Industrial Sensor Node, LIN Automotive Sub-Bus Controller, Industrial Motor and Relay Controller, Building Automation and HVAC Controller, Compact Embedded Data-Acquisition System.
Automotive Body Control Module
The C8051F575-IM fits a body-control module that must coordinate distributed vehicle functions over CAN and LIN. Its 50 MHz 8051-compatible core executes at up to 50 MIPS, allowing control logic, diagnostics, and debouncing to coexist without moving the design to a larger processor. The 16 KB Flash and 2.25 KB RAM support embedded firmware and working state, while the 1.8 V to 5.25 V supply range accommodates automotive power-conditioning stages. AEC-Q100 qualification supports the device’s use in automotive electronic systems. Designers should still allocate the exposed pad for thermal dissipation and verify each communication and I/O assignment against the C8051F57x documentation.
추천
CAN-Connected Industrial Sensor Node
The C8051F575-IM supports compact sensor nodes that collect local measurements and transmit results over a CAN network. Its mixed-signal resources include programmable-gain inputs, ±1 LSB integral nonlinearity, and conversion throughput up to 200 ksps, allowing low-level transducer signals to be conditioned and sampled without a separate high-resolution converter. The 50 MIPS execution rate provides capacity for calibration, filtering, diagnostics, and network handling around the acquisition task. A 1.8 V minimum supply also supports low-voltage sensor architectures. Use local decoupling, protected routing, and a ground strategy that separates analog returns from CAN and digital switching paths.
추천
LIN Automotive Sub-Bus Controller
The C8051F575-IM is suitable for LIN-connected modules that interface body electronics, switches, sensors, or actuators to a vehicle sub-network. Its integrated LIN capability eliminates the need for a separate communication controller, while the 8051-compatible core handles device-specific logic at up to 50 MIPS. Sixteen kilobytes of Flash provides room for protocol routines, diagnostics, calibration values, and application code, while 2.25 KB of RAM supports message buffers and state management. The 40-QFN package reduces controller-board area, but exposed-pad soldering and thermal validation remain essential in compact automotive electronics. Confirm the exact LIN peripheral resources and alternate-function mapping for the selected device variant.
추천
Industrial Motor and Relay Controller
The C8051F575-IM can serve as the supervisory controller in industrial motor, relay, and actuator systems where deterministic I/O handling and mixed-signal monitoring are required. Its 50 MIPS execution capability allows the firmware to combine state-machine control, timing, fault detection, and communications, while the integrated analog conversion resources can monitor current, temperature, or supply conditions. The 1.8 V to 5.25 V operating range supports both low-voltage logic and 5 V control sections. In a power-switching environment, keep the MCU away from high di/dt traces, provide local bulk and ceramic decoupling, and use the exposed pad as part of the thermal design.
추천
Building Automation and HVAC Controller
The C8051F575-IM fits distributed HVAC and building-automation controllers that combine environmental sensing, scheduled control, and serial communications. Programmable-gain analog inputs can accommodate sensors with different signal ranges, and the conversion capability of up to 200 ksps supports responsive acquisition tasks. The 50 MHz core leaves processing headroom for control algorithms, diagnostic rules, and communications, while 16 KB Flash accommodates embedded firmware. CAN and LIN connectivity can connect the controller to distributed field equipment when the system uses those buses. The 40-QFN package helps reduce controller size, but developers should plan careful thermal-pad assembly, supply filtering, and analog grounding.
추천
Compact Embedded Data-Acquisition System
The C8051F575-IM is appropriate for compact acquisition modules that sample analog signals, apply programmable gain, and report results through a serial or automotive network. Its mixed-signal converter provides ±1 LSB INL and throughput up to 200 ksps, while the 50 MIPS core can execute filtering, calibration, and packet-processing tasks. Sixteen kilobytes of Flash and 2.25 KB of RAM are suitable for embedded control rather than workstation-class signal processing. Its 1.8 V to 5.25 V range allows flexible interface selection, and the QFN-40 package supports compact instrumentation. Use a quiet analog ground region, short acquisition traces, and suitable bypass capacitance to preserve conversion performance.
추천
추천 제품 요약
엔지니어링 참조 데이터: C8051F575-IM — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | C8051F574-IM | C8051F571-IM | C8051F569-IM | C8051F509-IM | C8051F568-IM |
|---|---|---|---|---|---|---|
| Package | 40-QFN (6 x 6 mm) | 40-QFN (6 x 6 mm) | 40-QFN (6 x 6 mm) | 40-QFN (6 x 6 mm) | 40-QFN (6 x 6 mm) | 40-QFN (6 x 6 mm) |
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Processor Core | 8-bit 8051 CISC | 8051 | 8051 | 8051 | 8051 | 8051 |
주요 차별점
- Automotive communication integration (vs C8051F568-IM)
- Memory balance (vs C8051F568-IM)
- Closely matched family configuration (vs C8051F574-IM)
- Same package with a different ordering configuration (vs C8051F575-IMR)
설계 노트
The 40-QFN package includes an exposed pad that must be incorporated into the PCB thermal design. Provide a solderable land pattern on a multilayer board and connect it according to the manufacturer package guidance. Estimated thermal analysis should use the maximum ambient temperature, junction-temperature limit, actual supply voltage, and measured or calculated device dissipation rather than nominal clock performance alone. Maintain copper area and via density near the package so heat can spread away from the MCU.
Place the device-side supply bypass capacitors directly beside the relevant power pins and minimize loop area between each capacitor and the package. Keep analog inputs and their return paths away from CAN, LIN, clock, and switching-node traces. Because the package has 40 pins and an exposed pad, check the manufacturer land pattern mechanically and electrically before fabrication. Programming and debug access should be brought to accessible test pads without forcing long signal routes through analog areas.
Treat the 50 MHz clock requirement as a board-level signal-integrity consideration. Route the oscillator or external clock source away from analog inputs and sensitive reset or programming signals, observe the required bypass and layout arrangement, and avoid introducing stubs into high-speed nets. The mixed-signal converter supports throughput up to 200 ksps, so preserve a quiet return path and use local decoupling to prevent digital switching activity from coupling into sensor channels.
Do not approve a family-member substitution based only on the 40-QFN package. Verify pin multiplexing, alternate functions, memory limits, CAN and LIN resources, analog-channel assignments, clock requirements, reset behavior, and firmware dependencies for the exact alternative. A package-compatible substitution can still require code or board-option changes if peripheral assignments differ. Record the verified MPN, temperature range, qualification status, and package drawing in the production documentation.
규정 준수 정보
RoHS compliance is identified for the exact device, and the product listing identifies AEC-Q100 automotive qualification. Other environmental declarations are not specified.