CDK2307CILP64 - Dual 65MSPS 12/13-bit ADC | MaxLinear
부품 번호: CDK2307CILP64 ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $8.42 | $8.42 |
| 10 | $7.51 | $75.10 |
| 100 | $6.62 | $662.00 |
| 500 | $5.99 | $2,995.00 |
| 1,000 | $5.41 | $5,410.00 |
CDK2307CILP64 개요
An ADC (Analog-to-Digital Converter) is a data acquisition component that converts real-world analog signals into discrete digital codes for downstream processing by FPGAs, DSPs, microcontrollers, or ASICs. Within the converter hierarchy, the CDK2307CILP64 sits in the pipelined-ADC subcategory, which is the dominant topology for sampling rates between 10 MSPS and 250 MSPS because it balances high input bandwidth and resolution against modest die area and power. Selection between SAR (successive-approximation) and pipelined ADC families is driven primarily by the required sample rate and channel count.
Key features include simultaneous dual-channel sampling at up to 80 MSPS, a maximum sample rate of 80 MSPS at 12 bits and 65 MSPS at 13 bits, CMOS-compatible digital I/O, and an internal voltage reference that eliminates external reference components. The wide input common-mode range and low differential nonlinearity (DNL) make the converter well-suited to intermediate-frequency (IF) sampling, multi-carrier base-station receivers, and high-density video / imaging front ends. Power dissipation scales linearly with sample rate, allowing designers to trade speed for power in lower-throughput operating modes.
Architecturally, each channel of the CDK2307CILP64 uses a multi-stage pipelined switched-capacitor core followed by digital error-correction logic. The internal reference and clock-receiver blocks are shared between channels, while the analog inputs and digital outputs are independent, allowing simultaneous sampling of two real signals or one I/Q complex signal pair in a baseband or low-IF radio chain.
Typical applications include wireless infrastructure (GSM/EDGE/UMTS base-station receiver IF stages), cable-modem / set-top box downstream digitizers, multi-channel test and measurement instruments, ultrasound beamforming front ends, and dual-channel imaging / video capture. The 64-pin QFN exposed-pad package supports surface-mount PCB assembly and provides a low-thermal-resistance path to the PCB copper for heat spreading during sustained high-sample-rate operation.
When designing with this part, ensure each analog input is driven from a low-impedance, wideband differential buffer; bandwidth-limiting the analog front end below the Nyquist frequency (half the sample rate) prevents aliasing but must not degrade the aperture-time accuracy. Decouple AVDD and DVDD pins separately at the IC with 100 nF ceramic capacitors to keep the high-frequency switching currents out of the analog ground return.
This page synthesizes distributor pricing, parametric comparisons against pin-compatible dual ADCs, and practical PCB-layout guidance that goes beyond what is found in the manufacturer datasheet PDF.
드롭인 대체품: CDK2307CILP64 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: CDK2307CILP64 (동일 폼 팩터 및 풋프린트) — 차이점: Package, Resolution, Input Type, Manufacturer, Number of Channels.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
CDK2307CILP40
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
CDK1307CILP40
✅ 드롭인✓ 재고 있음
$3.95 / 개
데이터시트 보기 →CDK2307CILP64 최대 정격 & 전기적 특성
| Manufacturer | MaxLinear (formerly Exar / Cadeka) |
| Part Number | CDK2307CILP64 |
| 기능 | Dual-channel Analog-to-Digital Converter (ADC) |
| Number of Channels | 2 |
| 분해능 | 12-bit / 13-bit |
| Maximum Sample Rate | 80 MSPS (12-bit), 65 MSPS (13-bit) |
| Supported Sample Rates | 20 / 40 / 65 / 80 MSPS |
| Converter Architecture | Pipelined with digital error correction |
| Input Type | Differential analog inputs |
| Digital Output | Parallel CMOS |
| Data Interface | CMOS parallel |
| Reference Type | Internal (on-chip) |
| 패키지 | 64-pin QFN (LP64) with exposed pad |
| 실장 유형 | Surface Mount |
| Packaging | Tray |
CDK2307CILP64 64-pin qfn (lp64) with exposed pad 핀 구성 가이드
CDK2307CILP64(64-pin qfn (lp64) with exposed pad 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: CDK2307CILP64.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
CDK2307CILP64 적합 용도: 6 애플리케이션s: Wireless Infrastructure Base Station IF Sampling, Dual-Channel Video and Imaging Digitizer, Cable Modem and Set-Top Box Downstream Receiver, Multi-Channel Test and Measurement Instrumentation, Ultrasound Beamforming Front End, Software-Defined Radio I/Q Digitizer.
Wireless Infrastructure Base Station IF Sampling
The CDK2307CILP64's dual matched channels sampling simultaneously at 65-80 MSPS make it well suited to digitizing the intermediate-frequency (IF) outputs of multi-carrier base-station receivers. Each channel acquires one branch of a diversity or sector receiver, and the matched-sample-time architecture preserves the gain and phase relationship required for diversity combining and beamforming. The 12/13-bit resolution comfortably captures the dynamic range of a GSM/EDGE/UMTS/CDMA carrier set with margin for crest-factor peaks, while the CMOS parallel output streams directly into an FPGA for channelization. Power scales with sample rate, so dropping to 20 MSPS during low-traffic periods cuts dissipation for green base-station designs.
추천
Dual-Channel Video and Imaging Digitizer
The simultaneous-sampling dual-channel architecture of the CDK2307CILP64 captures two synchronized video or imaging streams from RGB/YUV or stereo cameras without requiring two separate ADC parts. At 65-80 MSPS the part digitizes standard HD video rates (148.5 MHz pixel clock) with sample headroom, while 12 or 13-bit resolution preserves color depth above the 8-bit broadcast standard for medical imaging, machine vision, and broadcast equipment. CMOS parallel outputs connect directly to FPGA video pipelines or dual-port video FIFOs, avoiding the latency and complexity of serialized JESD204B interfaces for shorter-distance PCB routes.
추천
Cable Modem and Set-Top Box Downstream Receiver
The 64-pin QFN dual ADC topology is a good fit for cable-modem downstream tuners and set-top box receivers where IF digitization is followed by digital demodulation in a single host processor. The 65-80 MSPS sampling rates capture DOCSIS/QAM IF bandwidths with margin for adjacent-channel rejection filtering, while 12-13 bits provides enough dynamic range for 256-QAM and below. The internal voltage reference eliminates an external reference chip and the associated drift/lifetime concerns at consumer price points. Operating temperature range must be confirmed against the datasheet for outdoor plant-mounted cable hardware.
추천
Multi-Channel Test and Measurement Instrumentation
Test instruments such as oscilloscopes, spectrum analyzers, and arbitrary-waveform-generator capture paths benefit from the dual matched channels of the CDK2307CILP64 because gain and phase tracking between channels directly determines amplitude-phase accuracy and image-rejection performance. At 65-80 MSPS the part handles bench-bandwidth channels up to ~30 MHz with margin, and the CMOS parallel output integrates with onboard FPGA DSP blocks for FFT, digital-down-conversion, or trigger derivation. Pairing the dual ADC with a wideband differential front-end amplifier is standard practice to avoid degrading the converter's high analog input bandwidth.
추천
Ultrasound Beamforming Front End
Medical and industrial ultrasound arrays digitize many channels simultaneously with strict gain/phase tracking; the dual matched channels of the CDK2307CILP64 fit channel-pair layouts where two transducer elements feed one converter IC. The 12/13-bit resolution is well matched to mid-range cart-based ultrasound systems, and 65-80 MSPS per channel comfortably exceeds the 30-40 MSPS needed for 15-20 MHz probe bandwidth. Exposed-pad QFN packaging supports dense PCB layouts with thermal headroom for continuously-operated phased-array probes, while CMOS parallel outputs feed the beamforming ASIC or FPGA with predictable deterministic latency.
추천
Software-Defined Radio I/Q Digitizer
The two matched ADC channels of the CDK2307CILP64 are well-suited to I/Q baseband sampling in software-defined radios, where one channel captures the I (in-phase) stream and the second captures the Q (quadrature) stream from a quadrature demodulator. Simultaneous sampling ensures the I/Q phase orthogonality is preserved, which is critical for image-rejection performance and low EVM in digital demodulation. At 65-80 MSPS the part handles HF/VHF baseband bandwidths up to ~30 MHz, while the CMOS parallel output fits standard FPGA DSP blocks for downconversion and demodulation pipelines.
추천
추천 제품 요약
엔지니어링 참조 데이터: CDK2307CILP64 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | CDK2307CILP40 | CDK1307CILP40 |
|---|---|---|---|
| Brand | MaxLinear (formerly Exar / Cadeka) | MaxLinear | MaxLinear |
| Package | 64-pin QFN (LP64) | 64-pin QFN (LP64) - same | 64-pin QFN (LP40) - same family footprint |
| Channels | 2 (dual, simultaneous) | 2 (dual, simultaneous) | 2 (dual, simultaneous) |
| Resolution | 12 / 13-bit | 12 / 13-bit | 13-bit fixed |
| Architecture | Pipelined with digital error correction | Pipelined with digital error correction | Pipelined with digital error correction |
| Internal Reference | Yes (on-chip) | Yes (on-chip) | Yes (on-chip) |
| Digital Output | CMOS parallel | CMOS parallel | CMOS parallel |
주요 차별점
- Dual matched-channel sampling at 65-80 MSPS in a 64-pin QFN (vs CDK2307CILP40)
- Selectable 12/13-bit resolution in the same die and package (vs CDK1307CILP40)
- CMOS parallel digital output for deterministic-latency FPGA interfaces (vs ADS58C28IRGC25 (LVDS-output dual ADC))
설계 노트
Treat the analog and digital grounds as a single low-impedance reference but keep their return-current paths separate on the PCB: route the analog input traces over a contiguous analog ground pour on the top layer, and the CMOS parallel output bus over the digital ground pour. Star-connect both grounds to the exposed pad (EP) of the 64-pin QFN with multiple stitching vias. Place the 100 nF AVDD decoupling capacitors within 2-3 mm of each analog supply pin to suppress switching-current spikes that otherwise couple into the analog input network and degrade SNR.
The dual matched ADC channels of the CDK2307CILP64 rely on identical analog front-end bandwidth and matched trace lengths on each channel to preserve gain and phase tracking. Lay out Channel A and Channel B input traces as length-matched differential pairs (target mismatch <0.5 mm) and use identical termination networks. The CMOS parallel output bus should be series-terminated close to the ADC with 22-33 ohm resistors; with 8-16 simultaneously switching CMOS outputs routing long parallel traces without termination causes ground-bounce and code-dependent channel-to-channel coupling.
Power dissipation on the CDK2307CILP64 scales linearly with sample rate (Estimated: ~1 mW per MSPS per channel at AVDD=3.3V based on typical pipelined-ADC curves), so drop the sample rate to 20 MSPS during standby or receive-only operation to reduce total dissipation. Separate AVDD and DVDD supplies with ferrite beads, and provide a dedicated 1.8V or 3.3V analog LDO upstream of AVDD to reject switching-converter ripple that would otherwise couple into the on-chip reference. Verify the analog input common-mode voltage matches the ADC's input CM range - exceeding it causes signal-dependent distortion not visible in basic DC checks.
Do not float the exposed thermal pad of the 64-pin QFN - it must be soldered to a low-impedance ground pour on the PCB with multiple thermal vias, otherwise both thermal performance and AC linearity degrade. Do not drive the analog inputs single-ended at the rated sample rate - use a wideband differential driver (e.g., a fully-differential op-amp or transformer) to realize the part's full SFDR. Finally, do not assume the internal reference is decoupled internally - add 100 nF plus 10 uF directly at the reference pin to suppress reference-induced conversion spurs.
규정 준수 정보
RoHS and lead-free compliance inferred from MaxLinear/Exar/Cadeka standard product lines for LP64 QFN packages; AEC-Q100 automotive qualification is not advertised for this part number. Halogen-free status not explicitly stated in the verified web data.
