CP2108-B03-GMR - USB to Quad UART Bridge, QFN-64 | Silicon Labs
부품 번호: CP2108-B03-GMR ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $7.32 | $7.32 |
| 10 | $6.59 | $65.90 |
| 100 | $5.86 | $586.00 |
| 500 | $5.2 | $2,600.00 |
| 1,000 | $4.61 | $4,610.00 |
CP2108-B03-GMR 개요
A USB-to-UART bridge is a device-class converter that translates USB packets into asynchronous serial frames, enabling legacy RS-232/RS-485 peripherals, sensors, and microcontrollers to communicate with a modern host that has dropped legacy COM ports. Within the broader interface IC taxonomy, the CP2108 sits in the bus bridge sub-category (USB bridge -> bridge IC -> interface IC -> integrated circuit), using the USB Communications Device Class (CDC) on the host side and a transparent UART on the device side to eliminate firmware-side protocol stacks.
Key features include four independent UART channels each supporting hardware flow control (RTS/CTS), programmable baud rates from 300 bps to 921.6 kbps, on-chip EEPROM for custom VID/PID and product-string storage, and a built-in 3.3 V LDO that can supply external logic up to 100 mA. The internal clock generator removes the need for an external crystal, and an integrated power-on reset circuit ensures clean enumeration even on noisy USB VBUS rails.
Typical applications cover industrial multi-port serial hubs, point-of-sale terminals with cash drawer / scanner / barcode-reader / printer ports, RS-232/RS-485 field-service dongles, multi-drop Modbus gateways, and test-and-measurement fixtures that aggregate several UART instruments onto one USB port. The combination of four independent UARTs, a CDC driver stack provided by Silicon Labs, and BOM-saving integration reduces PCB area and BOM cost versus building four CP2102 bridges.
Designers should pay attention to USB 2.0 signal-integrity on the upstream port - keep the D+/D- traces 90 ohm differential, length-matched, and routed over a continuous reference plane. The internal 3.3 V LDO is intended for light logic-rail loads; do not power RF stages from REG3V3. Suspend current is well below the USB 2.0 specification, so bus-powered designs typically pass gold-tree compliance without extra load switches.
드롭인 대체품: CP2108-B03-GMR — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: CP2108-B03-GMR (동일 폼 팩터 및 풋프린트) — 차이점: Package, RoHS Status, Supply Voltage, Flow Control, Integrated Functions.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
CP2108-B03-GM
✅ 드롭인✓ 재고 있음
$3.7973 / 개
데이터시트 보기 →CP2108-B01-GMR
✅ 드롭인✓ 재고 있음
$4.35 / 개
데이터시트 보기 →CP2108-B03-GMR 사양
| 기능 | USB to Quad UART Bridge Controller |
| Protocol | USB 2.0 Full-Speed |
| UART Channels | 4 |
| 공급 전압 | 3.0 V to 3.6 V |
| Baud Rate | 300 bps to 921.6 kbps (per UART) |
| Data Bits | 5, 6, 7, 8 bits |
| Parity | None, Even, Odd, Mark, Space |
| Stop Bits | 1, 1.5, 2 |
| Flow Control | Hardware (RTS/CTS) and Software (XON/XOFF) per UART |
| Modem Control Signals | Full (DTR, DSR, RTS, CTS, DCD, RI) per channel |
| Internal Oscillator | Yes (crystal-less USB operation) |
| Internal LDO | 3.3 V output, up to 100 mA for external logic |
| On-chip EEPROM | Yes (VID, PID, serial number, product string, GPIO configuration) |
| GPIO | Configurable multi-IO pins (revision B03 feature) |
| 동작 온도 | -40 C to +85 C |
| 패키지 / 케이스 | 64-QFN (9 mm x 9 mm) |
| Supplier Device Package | 64-QFN 9 x 9 |
| 실장 유형 | Surface Mount |
| RoHS 상태 | Compliant (per manufacturer page) |
CP2108-B03-GMR 64-qfn 9 x 9 핀 구성 가이드
CP2108-B03-GMR(64-qfn 9 x 9 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: CP2108-B03-GMR.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
CP2108-B03-GMR 적합 용도: 6 애플리케이션s: Industrial Multi-Port Serial Hub, Point-of-Sale (POS) Terminal Backplane, USB-to-RS-485 Field-Service Dongle, Test and Measurement Instrument Aggregation, Multi-Drop RS-485 Sensor Gateway, USB CDC Industrial Console Server.
Industrial Multi-Port Serial Hub
The CP2108-B03-GMR's four independent UARTs with full modem control make it ideal for industrial serial hubs that aggregate Modbus RTU, RS-232 instruments, and RS-485 sensors onto one upstream USB port. Each channel supports hardware flow control (RTS/CTS) up to 921.6 kbps, so a single upstream USB 2.0 link reliably expands into four galvanically-isolated downstream ports without protocol multiplexing.
추천
Point-of-Sale (POS) Terminal Backplane
POS systems need simultaneous links to barcode scanners, cash drawers, magnetic-stripe readers, and receipt printers - four downstream devices that traditionally required multiple bridge ICs. The CP2108-B03-GMR consolidates those four UARTs into one 9x9 mm QFN with internal 3.3 V LDO, shrinking the backplane BOM. The internal oscillator also eliminates the crystal, easing USB certification on the wide-VBUS supplies common in retail hubs.
추천
USB-to-RS-485 Field-Service Dongle
Field-service technicians running Modbus SCADA diagnostics frequently need a pocket-sized USB stick with four isolated RS-485 ports - the CP2108-B03-GMR delivers that in one chip without a crystal. Each UART's programmable baud generator plus the on-chip 64-byte FIFO keeps host CPU overhead low even when four Modbus masters are polled concurrently. Revision B03's multi-IO GPIO simplifies direction-control and fault-indicator lines without an extra IO expander.
추천
Test and Measurement Instrument Aggregation
ATE fixtures that previously stacked four CP2102 single-UART bridges can replace them with one CP2108-B03-GMR, saving 60% of the bridge-related PCB area. Each independent 921.6 kbps UART combined with the Silicon Labs VCP driver means existing test scripts written for COM ports work unchanged while the host sees COM7 through COM10. On-chip EEPROM stores custom VID/PID so multiple dongles enumerate with unique serial numbers.
추천
Multi-Drop RS-485 Sensor Gateway
Multi-drop RS-485 gateways serving 32+ sensor nodes per channel benefit from the CP2108-B03-GMR's ability to host four parallel RS-485 buses via attached transceivers, multiplying the per-gateway node count by 4x. Revision B03's configurable GPIOs handle per-channel DE/RE control and link-activity LEDs without external glue logic. The internal 3.3 V LDO powers those transceivers directly, simplifying battery-backed sensor node field installations.
추천
USB CDC Industrial Console Server
Console servers for switches, routers, and PLCs typically expose 4-16 RJ-45 serial ports via USB to the host; the CP2108-B03-GMR provides the first four channels without needing an FPGA mux. Combined with the Silicon Labs CDC driver, the resulting out-of-the-box COM port visibility shortens field-deployment time and avoids the licensing cost of vendor-specific drivers. Revision B03 GPIOs feed per-port status LEDs and link-detect logic with no extra IO expander.
추천
추천 제품 요약
엔지니어링 참조 데이터: CP2108-B03-GMR — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | CP2108-B03-GM | CP2108-B01-GMR |
|---|---|---|---|
| Brand | Silicon Labs | Silicon Labs | Silicon Labs |
| Package | 64-QFN (9x9 mm) | 64-QFN (9x9 mm) - identical | 64-QFN (9x9 mm) - identical |
| UART Channels | 4 | 4 | 4 |
| USB Standard | USB 2.0 Full-Speed | USB 2.0 Full-Speed | USB 2.0 Full-Speed |
| Maximum Baud Rate | 921.6 kbps | 921.6 kbps | 921.6 kbps |
| Supply Voltage | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V |
| Internal LDO | 3.3 V / 100 mA | 3.3 V / 100 mA | 3.3 V / 100 mA |
| Revision / GPIO Mapping | B03 with multi-IO GPIO configuration | B03 with multi-IO GPIO configuration | B01 with legacy GPIO mapping |
| Shipping Packaging | 1000-piece reel (GMR suffix) | 100-piece tray (GM suffix) | 1000-piece reel (GMR suffix) |
| Lifecycle Status | Active | Active | Active (older revision) |
주요 차별점
- Revision B03 multi-IO GPIO configuration (vs CP2108-B01-GMR)
- 1000-piece reel packaging for SMT lines (vs CP2108-B03-GM)
- Internal 3.3 V LDO with 100 mA budget (vs CP2102-GMR (single UART bridge))
설계 노트
Lay out the upstream USB D+ and D- traces as a 90 ohm differential pair, length-matched within 150 mil, routed over a continuous ground reference plane on layer 2. Place the VBUS bypass cap within 100 mil of the VBUS pin. The internal 3.3 V LDO is intended for light loads (<=100 mA) - do not power RF transceivers from REG3V3.
Estimated: with four UARTs at 921.6 kbps simultaneously, total host-side interrupt rate is approximately 73 kHz per channel. The CP2108's 64-byte hardware FIFO per channel means most desktop-class hosts can sustain full-throughput across all four channels without flow-control pauses; verify with the Silicon Labs AN721 application note on multi-port throughput.
Avoid mixing CP2108 PCB designs with USB 3.0 SuperSpeed stacks - the device only operates at 12 Mbps Full-Speed, and on a hub downstream port with USB 2.0 signalling the device will enumerate correctly. Ensure the upstream port is not forced to USB 3.0-only mode via host policy. Drivers are bundled with Silicon Labs' CP210x VCP package on Windows; macOS and Linux include in-box CDC-ACM drivers.
규정 준수 정보
RoHS and REACH compliance per Silicon Labs product page and PCN 170713107 (revision B03). No AEC-Q100 automotive grade is offered - choose CP2102N-A01-GQFN28R for AEC-Q100 USB-UART applications. Halogen-free status not explicitly published in the verified data.
