DCM3623T75X1380T00 - 80W Isolated DC-DC Converter | Vicor
부품 번호: DCM3623T75X1380T00 ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $185 | $185.00 |
| 10 | $172 | $1,720.00 |
| 100 | $158 | $15,800.00 |
| 500 | $145 | $72,500.00 |
| 1,000 | $132 | $132,000.00 |
DCM3623T75X1380T00 개요
A DCM (DC-DC Converter Module) is an isolated, regulated switching power converter that combines a Zero-Voltage Switching (ZVS) topology with planar magnetic structures to deliver high efficiency in a small footprint. Within the broader power management hierarchy, DCM modules sit between discrete switching regulators (lower density, lower isolation) and full custom power supplies, serving as the building block for distributed power architectures in industrial, aerospace, and defense applications where isolation, density, and time-to-market all matter.
Key differentiating features of the DCM3623T75X1380T00 include its ZVS high-frequency switching architecture, which minimizes switching losses and EMI, and its wide 9-75 Vdc input range that supports 12 V, 24 V, 28 V, 36 V, and 48 V nominal system buses without derating. The 2250 Vdc isolation rating meets the reinforced insulation requirements of industrial IEC 60950-style end equipment. Planar magnetic construction eliminates wire-wound transformer variability and supports automated SMT-style processing despite the through-hole pin format.
The internal architecture uses a ZVS primary-side controller with a proprietary Sine Amplitude Converter (SAC) topology, secondary-side rectification, and a closed-loop feedback path that regulates the 12 V output across line and load. The wide-input range is achieved through Vicor's Factorized Power Architecture (FPA), in which the upstream PI controller can pre-regulate bulk DC and the downstream DCM provides point-of-load isolation and voltage transformation.
Typical applications include industrial 24 V and 48 V bus distributed power, railway and rail-transit auxiliary power, defense and aerospace ground vehicles, test and measurement instrumentation, and any SELV-isolated load requiring 12 V at up to 6.7 A from a wide input bus.
A key design consideration is thermal management: at 90.4% peak efficiency the module dissipates roughly 8.6 W at full 80 W output, so adequate chassis airflow or cold-plate contact is required for continuous operation at 125°C junction temperature.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical thermal notes not found in the manufacturer datasheet, giving engineers a single reference for sourcing, replacement, and design-in decisions.
드롭인 대체품: DCM3623T75X1380T00 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: DCM3623T75X1380T00 (동일 폼 팩터 및 풋프린트) — 차이점: Function, Mounting Type, Nominal Input Voltage, Operating Temperature Range, Topology.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
DCM3623T50M53C2T70
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
DCM3623T50M06A8M70
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
V375A28C600BG
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
DCM3623T75X1380T00 최대 정격 & 전기적 특성
| 토폴로지 | Isregulated DCM with ZVS switching |
| 기능 | Isolated DC-DC Converter Module |
| 입력 전압 범위 | 9 V to 75 V |
| Nominal Input Voltage | 42 V |
| Output Voltage (Nominal) | 12.0 V |
| Output Current (Continuous) | 6.70 A |
| Output Power | 80 W |
| Peak Efficiency | 90.4% |
| Power Density | 220 W/in³ |
| Isolation Voltage | 2250 Vdc |
| Safety Classification | Safety Extra Low Voltage (SELV) |
| 패키지 | 9-pin R-XDMA-T9 ChiP (through-hole) |
| Package Dimensions | 22.8 mm x 38.72 mm |
| 실장 유형 | Through Hole (Board Mount) |
| 출력 수 | 1 |
| 동작 온도 범위 | -40°C to +125°C |
| Switching Topology | ZVS high-frequency |
| 출력 유형 | Fixed 12 V nominal |
| Automotive Qualified | Yes (per datasheets.com listing) |
DCM3623T75X1380T00 핀 구성
| 핀 1 | VIN+ — Positive input voltage (9-75 Vdc) |
| 핀 2 | VIN- — Negative input voltage / input ground return |
| 핀 3 | PC — Primary Control (enable / disable) |
| 핀 4 | NC — Not connected (per datasheet) |
| 핀 5 | +VOUT — Positive output voltage (12 V nominal) |
| 핀 6 | GND — Output ground return |
| 핀 7 | TR — Trim (output voltage adjustment) |
| 핀 8 | SG — Signal Ground |
| 핀 9 | FT — Fault / Temperature monitor (per datasheet) |
일반적인 애플리케이션
DCM3623T75X1380T00 적합 용도: 7 애플리케이션s: Industrial 24V/48V Bus Distributed Power, Railway and Rail-Transit Auxiliary Power, Defense and Aerospace Ground Vehicles, Test and Measurement Instrumentation, LED Driver and Industrial Lighting Control, Distributed Power Architecture (DPA) Building Block, Automotive Auxiliary and SELV Subsystems.
Industrial 24V/48V Bus Distributed Power
The DCM3623T75X1380T00 is purpose-built for 24 V and 48 V industrial distribution rails, accepting 9-75 Vdc and producing an isolated, regulated 12 V at 6.7 A (80 W). Its 2250 Vdc isolation lets it feed SELV-isolated secondary circuitry directly, eliminating intermediate isolation stages. Vicor's ZVS topology achieves 90.4% peak efficiency, so chassis thermal design is straightforward. Compared with discrete 24-to-12 V buck designs, the DCM delivers far higher power density (220 W/in³) and inherent isolation, reducing PCB area and BOM count for factory automation, PLC, and motor-drive auxiliary rails.
추천
Railway and Rail-Transit Auxiliary Power
Railway on-board and trackside systems often use 24 V, 36 V, 48 V, 72 V, and 110 V nominal bus rails that vary widely with load dump. The DCM3623T75X1380T00's 9-75 Vdc input window handles these buses directly while the 2250 Vdc isolation satisfies reinforced insulation requirements for EN 50155-style rail end equipment. At 80 W it powers doors, lighting, sensors, and on-board telemetry from a single SELV-isolated 12 V rail. The 9-pin ChiP through-hole package withstands the shock, vibration, and -40°C to +125°C thermal environment typical of rail installations.
추천
Defense and Aerospace Ground Vehicles
Military ground vehicles run on 28 Vdc nominal buses with significant transients. The DCM3623T75X1380T00 accepts the full 9-75 Vdc envelope and provides an isolated 12 V at 6.7 A (80 W) for radios, vetronics displays, sensor payloads, and mission computers. The 2250 Vdc isolation and wide -40°C to +125°C operating range meet MIL-style environmental specs for vetronics. Its 220 W/in³ density shrinks power-converter footprint, freeing volume for sensors and batteries; planar magnetics improve reliability versus wire-wound converters.
추천
Test and Measurement Instrumentation
Bench-top and rack-mount test equipment requires clean, isolated low-voltage rails (often 12 V) from varied AC-derived or 24/48 Vdc inputs. The DCM3623T75X1380T00 produces a regulated, isolated 12 V at up to 6.7 A from 9-75 Vdc, ideal for powering analog front-ends, DAC/ADC boards, and FPGA co-processors. Its 2250 Vdc isolation protects sensitive measurement paths from ground loops in stacked instruments. The ZVS topology generates minimal EMI, easing compliance with EN 55011/CISPR 11 lab-radiated limits.
추천
LED Driver and Industrial Lighting Control
Architectural and industrial LED drivers benefit from isolated, regulated 12 V auxiliary rails to power LED controllers, fans, and control MCUs. The DCM3623T75X1380T00's 80 W capacity handles a controller cluster plus cooling, and the SELV-rated 12 Vout lets designers wire directly to user-accessible controls. Its wide-input tolerance accommodates long-rail 24 Vdc drops and 48 V industrial buses without re-design. The 90.4% peak efficiency and planar-magnetic ChiP construction lower operating temperature versus discrete flyback LED supplies.
추천
Distributed Power Architecture (DPA) Building Block
Vicor's DCM family is the canonical building block for Factorized Power Architectures, where an upstream PI controller pre-regulates bulk DC and a downstream DCM isolates and steps down to point-of-load voltages. The DCM3623T75X1380T00 occupies the downstream slot, transforming the pre-regulated bus into an isolated 12 V at 6.7 A. This architecture scales from a single DCM to array N (parallel) or array M (redundant) configurations. Compared with traditional full-brick or intermediate-bus converters, FPA with DCMs achieves higher density and faster transient response.
추천
Automotive Auxiliary and SELV Subsystems
Automotive 12 V and 24 V (truck/bus) systems require isolated SELV rails for infotainment, ADAS sensors, and body controllers. The DCM3623T75X1380T00's 9-75 V window covers 12 V and 24 V nominal buses with load-dump margin, and its 2250 Vdc isolation protects downstream electronics from transients. The automotive-grade -40°C to +125°C range supports under-hood and chassis mounting. Compared with discrete flyback designs, the DCM's ZVS topology reduces EMI and improves efficiency at the wide VIN/VOUT ratios typical of automotive 24 V to 12 V conversion.
추천
추천 제품 요약
엔지니어링 참조 데이터: DCM3623T75X1380T00 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | DCM3623T50M53C2T70 | DCM3623T50M06A8M70 | V375A28C600BG |
|---|---|---|---|---|
| Package | 9-pin R-XDMA-T9 ChiP (through-hole) | 9-pin R-XDMA-T9 ChiP - same | 9-pin R-XDMA-T9 ChiP - same | Vicor Mini (through-hole) |
| Brand | Vicor | Vicor | Vicor | Vicor |
| Input Voltage Range | 9 V to 75 V | 36 V to 75 V (narrower) | 36 V to 75 V (narrower) | 250 V to 425 V (high-voltage) |
| Nominal Input Voltage | 42 V | 48 V | 48 V | 375 V |
주요 차별점
- Widest input voltage range in the DCM3623 family (vs DCM3623T50M53C2T70)
- Higher power density than full-brick alternatives (vs V375A28C600BG)
- 12 V output tailored for SELV end equipment (vs DCM3623T50M53C2T70)
설계 노트
At 80 W output and 90.4% peak efficiency, internal dissipation is approximately 8.6 W (estimated: Pdiss = Pout × (1/η − 1) = 80 × (1/0.904 − 1)). The ChiP through-hole package conducts heat into the host PCB copper; design at least 2-3 sq. in. of 2 oz copper on input and output pin landings. In sealed enclosures above 60°C, derate to 50-60 W or add forced-air cooling to maintain junction below 125°C.
Place input bulk capacitance (typically 4.7-22 µF ceramic per datasheet) within 5 mm of the VIN+ and VIN- pins to suppress ZVS ringing. Output capacitance (typically 22-100 µF ceramic + bulk) must be within 10 mm of +VOUT and GND. Use a star-ground layout so input and output return currents do not share a single trace; otherwise loop inductance degrades ZVS behavior and increases conducted EMI.
Do not apply input voltage above 75 Vdc - the device has no over-voltage clamping and will damage. Confirm the upstream source is current-limited or fused. Do not load the trim (TR) pin with external resistors without consulting the datasheet trim equations; out-of-range trim values can saturate the internal feedback loop. Finally, respect the isolation barrier: do not place any conductor (trace, via, component) within the 4 mm clearance specified in the datasheet, or 2250 Vdc isolation is compromised.
규정 준수 정보
Automotive-grade listed per datasheets.com aggregator; AEC-Q100 status not confirmed in web data. RoHS, REACH, lead-free, halogen-free, and conflict-mineral data not present in verified sources - all marked unknown.
