EFM32LG330F64-QFN64 - 48MHz Cortex-M3 MCU | Silicon Labs
부품 번호: EFM32LG330F64-QFN64 ✓ 활성EFM32LG330F64-QFN64 개요
A microcontroller is a programmable semiconductor that combines a processor core, memory, peripherals, and interface blocks on one integrated circuit. The EFM32LG family belongs to the broader hierarchy of embedded processor, microcontroller, and semiconductor devices. Its ARM Cortex-M3 core provides a common 32-bit instruction set and software ecosystem, while the Leopard Gecko platform adds low-power operation, autonomous peripherals, and extensive analog and digital integration for compact embedded products.
The EFM32LG330F64-QFN64 supports operation up to 48 MHz and includes a Memory Protection Unit for isolating software tasks. Its 64 KB Flash memory provides code storage, while 32 KB of RAM supports working data, stacks, and peripheral buffers. The integrated USB and AES functions simplify designs that need USB connectivity and hardware-assisted encryption without requiring separate devices.
Energy efficiency is central to the EFM32LG architecture. The manufacturer datasheet states that the family can consume as little as 0.65 µA in Stop mode and 211 µA/MHz in Run mode. Autonomous peripherals can perform selected tasks while the processor sleeps, reducing the energy required for sensing, timing, communications, and low-rate data acquisition in battery-operated equipment.
Typical uses include connected sensor nodes, industrial monitoring equipment, portable measurement instruments, USB-enabled embedded controllers, and low-power IoT products. The 1.98 V to 3.8 V supply range supports both 2 V and 3.3 V system architectures. Designers should verify USB transceiver requirements, clocking, pin multiplexing, and the exposed-pad layout in the manufacturer pinout and reference design before schematic release.
For PCB implementation, use the manufacturer QFN-64 land pattern, connect the exposed pad to the appropriate ground plane, and place decoupling capacitors close to the supply pins. Confirm every peripheral signal against the package pin description because 64-pin QFN devices offer limited escape routing and can require careful fanout between fine-pitch pins and external components.
This page combines the manufacturer EFM32LG datasheet, distribution specifications, low-power performance data, documented cross-references, and engineering guidance to clarify device selection, board implementation, and genuine pin-compatible replacement decisions.
드롭인 대체품: EFM32LG330F64-QFN64 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
EFM32LG330F64G-E-QFN64
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
EFM32LG330F64G-QFN64
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
EFM32LG330F64-QFN64 최대 정격 & 전기적 특성
| Product Type | 32-bit ARM Cortex-M3 microcontroller |
| Processor Core | ARM Cortex-M3 |
| 최대 클록 주파수 | 48 MHz |
| Flash Memory | 64 KB |
| RAM | 32 KB |
| Supply Voltage Range | 1.98 V to 3.8 V |
| Series | Leopard Gecko |
| 패키지 | 64-pin QFN |
| 실장 유형 | Surface mount |
| USB Interface | Integrated USB |
| Security Feature | AES |
| Stop Mode Current | 0.65 µA |
| Run Mode Current | 211 µA/MHz |
| Memory Protection Unit | Integrated |
| RoHS 상태 | RoHS Compliant |
| Lead-Free Status | Lead Free |
EFM32LG330F64-QFN64 64-pin qfn 핀 구성 가이드
EFM32LG330F64-QFN64(64-pin qfn 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: EFM32LG330F64-QFN64.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
EFM32LG330F64-QFN64 적합 용도: 6 애플리케이션s: Connected Sensor Nodes, USB-Enabled Embedded Controllers, Industrial Monitoring Equipment, Portable Measurement Instruments, Battery-Powered Data Loggers, Low-Power IoT Controls.
Connected Sensor Nodes
The EFM32LG330F64-QFN64 fits connected sensor nodes that need more processing capability than an 8-bit controller while retaining low-power operation. Its 48 MHz ARM Cortex-M3 core, 32 KB RAM, and 64 KB Flash are sufficient for sensor conditioning, local filtering, protocol management, and application logic. The EFM32LG family can consume as little as 0.65 µA in Stop mode, allowing the processor to sleep while autonomous peripherals continue selected tasks. Designers can place the controller beside a communications radio and sensor front end while retaining USB access for configuration or maintenance. The principal design consideration is balancing radio duty cycle, sensor current, regulator efficiency, and MCU leakage within the battery budget.
USB-Enabled Embedded Controllers
The integrated USB capability of the EFM32LG330F64-QFN64 makes it useful for embedded controllers that enumerate as a USB device, implement a custom peripheral interface, or support USB-based configuration. Its 48 MHz Cortex-M3 core provides deterministic handling of protocol tasks, while 64 KB of Flash and 32 KB of RAM accommodate firmware, descriptors, buffers, and application state. The 1.98 V to 3.8 V supply range supports 2 V and 3.3 V system rails. USB implementation requires careful attention to impedance-controlled routing, supply integrity, ground return paths, and the data-line topology specified by the manufacturer datasheet. USB bus power should be assessed separately because the MCU itself does not remove the need for compliant device-power and protection design.
Industrial Monitoring Equipment
The EFM32LG330F64-QFN64 is appropriate for industrial monitoring modules that combine analog measurements, digital control, local data processing, and status communications. Its 32 KB RAM can support acquisition buffers and control state, while the 48 MHz Cortex-M3 core can execute protocol stacks, filtering, and supervisory logic. The integrated Memory Protection Unit supports isolation of software tasks when system reliability is important. Low-power capability can reduce maintenance requirements in widely distributed or intermittently monitored installations. For industrial deployments, verify the exact temperature grade, isolation requirements, input protection, grounding strategy, and any required safety standards separately. Firmware should also include watchdog and brownout strategies appropriate to the monitored system rather than relying only on nominal operating conditions.
Portable Measurement Instruments
The EFM32LG330F64-QFN64 suits portable measurement instruments where display-independent control, data acquisition, calibration, and USB connectivity must coexist in a compact assembly. The 64 KB Flash provides room for firmware and configuration, while 32 KB of RAM supports working buffers for measurements and communication. Its Cortex-M3 instruction set and 48 MHz clock allow responsive control without a higher-power application processor. Stop mode can be used between measurement intervals, although the designer must account for sensor settling, reference warm-up, and display behavior in the duty cycle. The small QFN-64 package also reduces board area but requires thermal and assembly planning. Confirm exposed-pad implementation and pin multiplexing against the manufacturer package drawing before releasing the layout.
Battery-Powered Data Loggers
Battery-powered data loggers benefit from the EFM32LG330F64-QFN64 because the MCU combines a capable 48 MHz processor with family-level Stop-mode current as low as 0.65 µA and Run-mode current of 211 µA/MHz. Firmware can activate the processor only for acquisition, processing, and storage operations, then return the system to a low-energy state between events. The 64 KB Flash and 32 KB RAM are appropriate for small local datasets, event buffering, and protocol handling. Accurate battery-life projection should combine MCU consumption with sensor operation, nonvolatile storage writes, pull networks, regulator quiescent current, and battery self-discharge. Use brownout detection and controlled shutdown behavior to prevent corrupted logs when the supply falls below the operating range.
Low-Power IoT Controls
The EFM32LG330F64-QFN64 is well suited to low-power IoT control nodes that combine local logic with intermittent communications. Its autonomous peripherals can handle routine timing, comparison, or data-transfer activity while the Cortex-M3 core remains idle, helping reduce unnecessary active time. The integrated AES function supports designs that require hardware-assisted encryption, while USB can provide a service or configuration path before production deployment. The 1.98 V minimum supply voltage offers flexibility for compact power architectures, but the entire system still requires a regulator suitable for the radio and sensors. Security planning should cover keys, firmware updates, and authenticated communication rather than treating the AES block as a complete product-security solution. Firmware partitioning and watchdog use can protect long-duration deployments.
엔지니어링 참조 데이터: EFM32LG330F64-QFN64 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | EFM32LG330F64G-E-QFN64 | EFM32LG330F64G-QFN64 |
|---|---|---|---|
| Package | QFN-64 | QFN-64 | QFN-64 |
| Brand | Silicon Labs | Silicon Labs | Silicon Labs |
| Processor Core | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 |
| Maximum Clock Frequency | 48 MHz | 48 MHz | 48 MHz |
| Flash Memory | 64 KB | 64 KB | 64 KB |
| RAM | 32 KB | 32 KB | 32 KB |
| Security Feature | AES | AES | AES |
| USB Interface | Integrated USB | Integrated USB | Integrated USB |
주요 차별점
- Closest documented pin-compatible configuration (vs EFM32LG330F64G-E-QFN64)
- Low-power integration for embedded products (vs EFM32LG330F64G-QFN64)
- Connectivity and security in one device (vs EFM32LG330F64G-E-QFN64)
설계 노트
Use the manufacturer QFN-64 land pattern and thermal-pad connection without changing pad dimensions or pin numbering. Place the required input and bulk capacitors close to the corresponding power pins, and keep sensitive analog or communications traces away from the switching and high-current return areas of the board. Confirm the exposed-pad via pattern against the assembly process and solder mask requirements because an electrically correct footprint can still create voiding or assembly defects if the thermal interface is not designed correctly.
Plan the power tree for the complete operating range of 1.98 V to 3.8 V, including brownout behavior, USB attachment, radio or sensor load transients, and the current required by all I/O pins. The manufacturer's low-power figures describe the EFM32LG family, not the finished product. Validate regulator dropout, quiescent current, capacitor ripple rating, and shutdown sequencing with the highest expected load. Firmware should avoid configurations that exceed the limits of the selected external power components.
The 64-pin QFN footprint has fine-pitch escape routing, so assign external components according to the manufacturer pin table and establish critical routes before placing small passives. Keep USB and other high-speed interfaces over a continuous reference plane, minimize return-path discontinuities, and place decoupling at the pins rather than at a convenient but electrically distant location. Review the final assembly drawings for pin-one orientation and exposed-pad alignment.
Do not treat the QFN-64 package or the Leopard Gecko family name as sufficient evidence that every ordering suffix is interchangeable. Verify the exact MPN, temperature grade, errata status, USB configuration, pin assignments, and lifecycle status for each product revision. When changing to a G or E suffix, confirm that the firmware, boot configuration, qualification requirements, and approved BOM remain valid rather than relying only on the identical package and memory size.
규정 준수 정보
The device listing identifies RoHS Compliant and Lead Free status. REACH, halogen-free, and conflict-minerals status are not stated.