EFM32LG940F64-QFN64 - 48MHz ARM Cortex-M3 MCU | Silicon Labs
부품 번호: EFM32LG940F64-QFN64 ✓ 활성EFM32LG940F64-QFN64 개요
A microcontroller is the central programmable controller in an embedded electronic system. It executes instructions, reads sensors, controls actuators and manages communications. The EFM32LG family belongs to the hierarchy of 32-bit microcontroller, embedded processor, semiconductor and system-on-chip. Its Cortex-M3 architecture provides a practical balance of processing performance, deterministic peripheral operation and energy efficiency for battery-powered and industrial equipment.
The EFM32LG940F64-QFN64 supports operation up to 48 MHz while providing 64 KB of Flash organized as 64K x 8. Its 32 KB SRAM supports working data, stack storage and interrupt servicing. Silicon Labs emphasizes low power consumption across the family, with Run-mode consumption stated as 211 uA/MHz and Stop-mode consumption as low as 0.65 uA. These characteristics make the controller suitable where duty-cycled sensing, compact dimensions and predictable standby behavior are important.
The Leopard Gecko architecture incorporates autonomous peripherals, allowing time-critical tasks such as timer, counter, PWM, UART and ADC operations to continue with limited processor intervention. High analog integration reduces the need for discrete interface components, while fast wake-up behavior supports designs that spend much of their operating cycle in a low-energy state. The 64-pin QFN package also exposes the device's GPIO, communications and analog resources in a compact surface-mount footprint.
Typical applications include industrial sensor nodes, portable medical accessories, low-power instrumentation, connected building equipment, compact energy-monitoring devices and battery-operated products. The combination of 64 KB Flash, 32 KB SRAM and a 48 MHz Cortex-M3 core is suitable for moderate control workloads that need more capability than an 8- or 16-bit microcontroller but do not require a high-performance application processor.
PCB design should preserve short return paths for ground, analog and digital supply connections while following the manufacturer pin-description table for every QFN-64 signal. Place decoupling capacitors close to the supply pins, reserve a continuous ground plane under the device and follow the package land pattern and exposed-pad soldering requirements exactly.
This page combines the family's power characteristics, device variants, package constraints and application guidance into a practical engineering overview. It also highlights same-footprint EFM32LG940 options for engineers comparing Flash capacity, temperature grade or ordering suffix before finalizing a design.
드롭인 대체품: EFM32LG940F64-QFN64 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
EFM32LG940F64G-F-QFN64
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
EFM32LG940F64G-E-QFN64
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
EFM32LG940F128G-QFN64
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
EFM32LG940F256G-F-QFN64
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
EFM32LG940F256-QFN64
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
EFM32LG940F64-QFN64 최대 정격 & 전기적 특성
| Product Type | 32-bit ARM Cortex-M3 microcontroller |
| Series | EFM32 Leopard Gecko |
| Processor Core | ARM Cortex-M3 |
| 최대 클록 주파수 | 48 MHz |
| Flash Memory | 64 KB (64K x 8) |
| RAM | 32 KB |
| Supply Voltage Range | 1.98 V to 3.8 V |
| Run-Mode Current | 211 uA/MHz |
| Stop-Mode Current | 0.65 uA |
| 패키지 | 64-pin QFN, 9 x 9 mm |
| 실장 유형 | Surface mount |
| Architecture | ARMv7-M Cortex-M3 architecture |
| Digital I/O | 53 pins on the EFM32LG940F128G-QFN64 family variant |
| Timer Counters | 4 x 16-bit timer/counter blocks on the EFM32LG940F128G-QFN64 family variant |
| Data Word Size | 32 bit |
| Exposed Pad | Present |
EFM32LG940F64-QFN64 64-pin qfn, 9 x 9 mm 핀 구성 가이드
EFM32LG940F64-QFN64(64-pin qfn, 9 x 9 mm 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: EFM32LG940F64-QFN64.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
EFM32LG940F64-QFN64 적합 용도: 6 애플리케이션s: Battery-Powered Sensor Nodes, Industrial Monitoring and Control, Portable Health and Wellness Devices, Smart Building and IoT Equipment, Low-Power Instrumentation, Compact Power and Energy Monitoring.
Battery-Powered Sensor Nodes
The EFM32LG940F64-QFN64 fits compact battery-powered sensor nodes that periodically measure environmental or physical conditions and transmit the results through a low-power radio. Its 48 MHz ARM Cortex-M3 core can execute local filtering, calibration and protocol handling, while the 64 KB Flash provides room for firmware and constants. The 32 KB SRAM supports interrupt buffers and working data without requiring external memory. Family power figures of 211 uA/MHz in Run mode and as little as 0.65 uA in Stop mode make duty-cycle planning practical. For the lowest system energy, disable unused peripherals, avoid continuous polling and select a regulator whose quiescent current complements the controller's sleep behavior.
추천
Industrial Monitoring and Control
The EFM32LG940F64-QFN64 is suitable for industrial monitoring modules that combine digital inputs, analog sensing, counters and communication links. The 32-bit Cortex-M3 architecture handles more complex control logic than a small 8-bit controller, while the 64 KB Flash and 32 KB RAM are appropriate for moderate protocol and data-processing workloads. Its 1.98 V to 3.8 V operating range supports common embedded rails, and the 64-pin QFN package reduces board area. In an industrial design, protect externally connected I/O paths from transients, route analog signals away from switching nodes and confirm operating-temperature limits against the enclosure temperature and expected thermal rise.
추천
Portable Health and Wellness Devices
The EFM32LG940F64-QFN64 can serve as the control core in compact wellness devices, low-profile diagnostic accessories and portable health-monitoring products. Its low-power Cortex-M3 platform supports responsive wake-up behavior and efficient sensor sampling, while 64 KB of Flash and 32 KB of SRAM are sufficient for embedded control, filtering and communication tasks. The 64-pin QFN package supports dense, wearable-style layouts without relying on a large development board. Designers should define a safe state for each actuator, place medical front-end circuitry according to its own isolation and noise requirements, and verify that regulatory and qualification requirements for the complete product are met rather than inferred from the microcontroller alone.
추천
Smart Building and IoT Equipment
The EFM32LG940F64-QFN64 is appropriate for connected building equipment such as occupancy controllers, environmental monitors, wireless endpoints and small actuator hubs. The 48 MHz core supports protocol handling and local logic, while the energy-conscious Leopard Gecko platform reduces the burden on battery-operated or energy-harvested installations. The 64 KB Flash configuration can host a compact application, and the QFN-64 package leaves board area for sensors or radio circuitry. For reliable network endpoints, implement watchdog recovery, validate firmware-update behavior and ensure that the power supply remains stable during radio transmission. The controller's low-power capability should be evaluated with the complete radio, sensor and regulator load rather than in isolation.
추천
Low-Power Instrumentation
The EFM32LG940F64-QFN64 fits compact data loggers, handheld meters and low-power instrumentation that need deterministic control with modest memory requirements. The Cortex-M3 core provides 32-bit processing at up to 48 MHz, allowing sampling, calibration and local computation without a higher-power application processor. With 64 KB Flash and 32 KB SRAM, the device can support a control application, event buffering and a serial communications stack. Designers should separate analog input routing from digital activity, use a continuous ground reference beneath the package and account for exposed-pad heat spreading. When numeric performance is central, verify the peripheral clock configuration and sample timing in the manufacturer reference manual.
추천
Compact Power and Energy Monitoring
The EFM32LG940F64-QFN64 can supervise energy-management equipment that records voltage, current, state transitions or operating time. Its Cortex-M3 core handles sampling coordination, threshold logic, event logging and communications, while the 64 KB Flash is suitable for a focused monitoring application. The 1.98 V to 3.8 V supply range can simplify interfacing to low-voltage sensing circuitry when system rails are designed accordingly. Use the device's timers and event system to reduce polling overhead, and ensure any external measurement front end does not inject disturbances into analog rails. The exposed pad and compact QFN land pattern require careful thermal and solder-joint design to support reliable operation in enclosed products.
추천
추천 제품 요약
엔지니어링 참조 데이터: EFM32LG940F64-QFN64 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | EFM32LG940F64G-F-QFN64 | EFM32LG940F64G-E-QFN64 | EFM32LG940F128G-QFN64 | EFM32LG940F256G-F-QFN64 | EFM32LG940F256-QFN64 |
|---|---|---|---|---|---|---|
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Package | 64-pin QFN, 9 x 9 mm | 64-pin QFN, 9 x 9 mm - same package | 64-pin QFN - same package | 64-pin QFN - same package | 64-pin QFN - same package | 64-pin QFN - same package |
| Processor Core | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 | ARM Cortex-M3 |
| Maximum Clock Frequency | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Flash Memory | 64 KB | 64 KB | 64 KB | 128 KB | 256 KB | 256 KB |
| RAM | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB |
| Supply Voltage Range | 1.98 V to 3.8 V | 1.98 V to 3.8 V | 1.98 V to 3.8 V | 1.98 V to 3.8 V | 1.98 V to 3.8 V | 1.98 V to 3.8 V |
| Run-Mode Current | 211 uA/MHz | 211 uA/MHz family figure | 211 uA/MHz family figure | 211 uA/MHz family figure | 211 uA/MHz family figure | 211 uA/MHz family figure |
| Stop-Mode Current | 0.65 uA | 0.65 uA family figure | 0.65 uA family figure | 0.65 uA family figure | 0.65 uA family figure | 0.65 uA family figure |
주요 차별점
- Lower Flash capacity supports a smaller firmware footprint (vs EFM32LG940F128G-QFN64)
- Lower peak Run-mode current at the same clock speed (vs EFM32LG940F64G-F-QFN64)
- Smaller memory configuration for cost-constrained control tasks (vs EFM32LG940F256G-F-QFN64)
- Compact 64-pin package supports dense embedded layouts (vs EFM32GG230F512-QFN64)
설계 노트
Use the manufacturer QFN-64 land pattern and exposed-pad geometry without changing pad dimensions to compensate for assembly tolerances. Place the exposed pad on a continuous ground plane with a thermal-via pattern that satisfies the package and assembly requirements. Route sensitive analog inputs away from digital clocks and communication edges, and place the required bypass capacitors directly beside the associated supply pins to minimize supply-loop area.
The EFM32LG family can operate down to 1.98 V, but sequencing and transient behavior still depend on the selected regulator and load. Confirm the voltage limits for every supply rail, preserve the required startup order and evaluate brownout behavior for downstream equipment. Estimated: at the stated 211 uA/MHz family rate, processing at 48 MHz corresponds to about 10.128 mA before peripheral and board loads. Use this figure for power-tree planning, not as a guaranteed operating current.
The QFN-64 package relies heavily on its exposed pad for heat transfer. Connect that pad to ground, provide multiple thermal vias and avoid placing the device next to a heat-generating component without an airflow or copper-spreading plan. At 48 MHz, estimate the internal power using the actual supply voltage and active-current measurement, then compare the resulting junction-temperature margin with the manufacturer limit. Reduce clock frequency or peripheral activity when the enclosure limits heat dissipation.
Do not treat related EFM32LG940 order codes as automatically identical. Check the G suffix, temperature grade, Flash capacity and package marking against the production BOM before substitution. Likewise, do not infer behavior from the generic Leopard Gecko family: configure clocks, memory, sleep modes and peripheral instances according to the exact device variant and its device initialization procedure. Validate the programmed image and recovery path before deploying a change to a deployed product.
규정 준수 정보
RoHS, REACH, lead-free, halogen-free and conflict-minerals declarations require confirmation from the manufacturer or the applicable regulatory documentation.