HMCAD1040-40 - Dual 10-Bit 20/40 MSPS ADC | Analog Devices
부품 번호: HMCAD1040-40 ✓ 활성| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $18.5 | $18.50 |
| 10 | $16.2 | $162.00 |
| 100 | $13.85 | $1,385.00 |
| 500 | $11.95 | $5,975.00 |
| 1,000 | $10.4 | $10,400.00 |
HMCAD1040-40 개요
An ADC (analog-to-digital converter) is a data-acquisition component that converts continuous analog signals into discrete digital codes. Within the signal chain hierarchy, an ADC sits between the analog front end (sensor, amplifier, anti-alias filter) and the digital back end (DSP, FPGA, processor). Pipelined ADCs like the HMCAD1040-40 use a multi-stage architecture to achieve high sample rates at low power, making them well suited to multi-channel applications where energy and board area are constrained.
Key features include 10-bit resolution, 61.6 dB SNR at 8 MHz input, internal reference circuitry (eliminating the need for an external reference IC), a 1.8 V core supply, a 1.7-3.6 V I/O supply for direct interfacing to modern CMOS logic, parallel CMOS output data, and a serial CMOS control interface. The proprietary internal structure balances dynamic performance with very low power consumption across the 20/40 MSPS operating range.
In dual-channel mode the ADC can convert two independent analog inputs simultaneously, doubling channel density per package. The CMOS control interface allows configuration of channel selection, sample rate, and output formatting through a simple serial bus, while the parallel CMOS outputs integrate directly with ASICs, FPGAs, or microcontrollers without level translation.
Typical applications include portable instrumentation, handheld oscilloscope front ends, low-power medical imaging, IF sampling in communication receivers, and industrial multi-channel data acquisition. The combination of dual channels, 40 MSPS capability, and 43 mW power dissipation makes the part attractive for battery-powered and channel-dense designs.
When designing with this device, place the decoupling capacitors as close as possible to the analog and digital supply pins and keep the analog input traces short and guarded to preserve SNR. The internal reference is adequate for most applications, but a low-noise external reference may improve SFDR in the most demanding spectra.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that go beyond what the manufacturer datasheet alone provides, including a curated comparison against same-family ADI converters and pin-compatible cross-brand options.
드롭인 대체품: HMCAD1040-40 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: HMCAD1040-40 (동일 폼 팩터 및 풋프린트) — 차이점: Architecture, Control Interface, Package, Input Bandwidth (THA optimized), Number of Channels.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
HMCAD1040-20
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
HMCAD1520-80
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
AD9203ARU
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
HMCAD1040-40 최대 정격 & 전기적 특성
| Manufacturer | Analog Devices (formerly Hittite Microwave) |
| Part Number | HMCAD1040-40 |
| 분해능 | 10 bit |
| Number of Analog Inputs | 2 (dual channel) |
| Maximum Sampling Rate | 40 MSPS (also supports 20 MSPS) |
| Architecture | Pipelined (proprietary structure) |
| Power Dissipation at 20 MSPS | 24 mW |
| Power Dissipation at 40 MSPS | 43 mW |
| SNR at 8 MHz Input | 61.6 dB |
| Reference | Internal reference circuitry |
| Core Supply Voltage | 1.8 V |
| I/O Supply Voltage | 1.7 V to 3.6 V |
| Output Interface | Parallel CMOS |
| Control Interface | Serial CMOS |
| 패키지 | 64-SMT QFN (HVQCCN), 9x9 mm |
| Temperature Grade | Industrial |
| Terminal Form | No-lead (HVQCCN / QFN) |
| 실장 유형 | Surface Mount |
HMCAD1040-40 64-smt qfn (hvqccn), 9x9 mm 핀 구성 가이드
HMCAD1040-40(64-smt qfn (hvqccn), 9x9 mm 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: HMCAD1040-40.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
HMCAD1040-40 적합 용도: 6 애플리케이션s: Portable Instrumentation, Handheld Oscilloscope Front End, Low-Power Medical Imaging, IF Sampling in Communication Receivers, Industrial Multi-Channel Data Acquisition, Ultrasound Beamformer Sub-Array.
Portable Instrumentation
The HMCAD1040-40 fits portable, battery-powered instrumentation front ends where dual channels and low power dissipation are critical. Its 43 mW power at 40 MSPS and dual-input architecture let a handheld oscilloscope or data logger digitize two signals simultaneously without exceeding the thermal envelope of a small plastic enclosure. The internal reference removes the cost and board area of an external reference IC, which matters in compact, cost-sensitive portable designs where every square millimeter of PCB is reserved for sensors, batteries, or user I/O.
추천
Handheld Oscilloscope Front End
The HMCAD1040-40's 40 MSPS sample rate and dual channels support a two-channel handheld DSO front end, digitizing both CH1 and CH2 simultaneously with 10-bit vertical resolution. The 61.6 dB SNR at 8 MHz input keeps visible noise low on the display, while the parallel CMOS outputs feed directly into an FPGA or microcontroller for triggering and waveform rendering. The 43 mW dissipation at full speed keeps the handheld's battery budget manageable during extended field measurements.
추천
Low-Power Medical Imaging
Ultrasound and other low-power medical imaging front ends require simultaneous multi-channel digitization at modest sample rates. The HMCAD1040-40 dual 10-bit 40 MSPS channels serve as a building block for compact probe modules where channel density and low heat dissipation are paramount. Its internal reference and 1.8 V core supply simplify the safety-isolation design, while the CMOS outputs drive an FPGA-based beamformer or DSP without level translation.
추천
IF Sampling in Communication Receivers
The HMCAD1040-40 suits narrow-band IF sampling in low-cost communication receivers such as software-defined radio (SDR) and PMR base stations. Its 40 MSPS rate comfortably digitizes IF signals up to about 18 MHz with 10-bit resolution, while 61.6 dB SNR preserves modulation fidelity. The dual channels support diversity or I/Q baseband digitization, and the 1.7-3.6 V I/O supply allows direct interface to 3.3 V DSP or baseband processors.
추천
Industrial Multi-Channel Data Acquisition
Multi-channel industrial data-acquisition systems - such as vibration analyzers, process controllers, and condition-monitoring modules - benefit from the HMCAD1040-40's dual-channel density. Two ADCs per package reduce part count on the analog input board, lowering BOM cost and improving mean time between failures. The industrial temperature grade and 24/43 mW dissipation simplify cooling in DIN-rail or sealed enclosures with limited airflow.
추천
Ultrasound Beamformer Sub-Array
Within a portable ultrasound beamformer, the HMCAD1040-40 handles sub-array receive digitization with two channels per IC. The combination of dual inputs, 40 MSPS rate, and 43 mW power keeps the per-channel thermal budget within the patient-isolation enclosure limits. The parallel CMOS outputs feed directly into a beamforming FPGA, eliminating serializer latency and simplifying the timing closure for high-channel-count probe heads.
추천
추천 제품 요약
엔지니어링 참조 데이터: HMCAD1040-40 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | HMCAD1040-20 | HMCAD1520-80 | AD9203ARU |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 64-QFN (HVQCCN, 9x9 mm) | 64-QFN (HVQCCN, 9x9 mm) | 64-QFN (HVQCCN, 9x9 mm) | 48-TQFP (different package, not drop-in) |
| Resolution | 10 bit | 10 bit | 12 bit | 10 bit |
| Max Sample Rate | 40 MSPS | 20 MSPS | 80 MSPS | 125 MSPS |
| Number of Channels | 2 | 2 | 2 | 1 |
| Core Supply | 1.8 V | 1.8 V | 1.8 V | 3.0 V |
| Output Interface | Parallel CMOS | Parallel CMOS | Parallel CMOS | Parallel CMOS |
| RoHS | Compliant | Compliant | Compliant | Compliant |
주요 차별점
- Dual 10-bit channels at 40 MSPS with only 43 mW (vs Single-channel AD9203 (10-bit, 125 MSPS))
- Lower sample rate, even lower power (vs HMCAD1040-20)
- Internal reference eliminates external IC (vs Most competing 10-bit ADCs (e.g. ADS5203))
설계 노트
Provide a clean, low-noise 1.8 V analog supply (AVDD) with at least 10 uF bulk plus 0.1 uF and 10 nF decoupling placed within 5 mm of each AVDD pin. The 1.7-3.6 V DVDD supply should be derived from a separate LDO from the system 3.3 V rail to prevent digital switching noise from coupling into the analog input and degrading the 61.6 dB SNR. Estimated: at 43 mW dissipation and theta-JA of approximately 28 C/W (typical 64-QFN 9x9 mm), the junction temperature rise is only ~1.2 C above ambient - no heatsink is required.
Route analog inputs as 50 ohm controlled-impedance differential pairs and keep them short and guarded by ground pour on both sides. Place the analog input RC anti-alias filter within 10 mm of the ADC input pins. The exposed thermal pad must be soldered to a continuous ground plane with at least 9 thermal vias to the inner ground layers for low-impedance grounding and heat spreading. Do not route digital output traces under the analog input section.
Common pitfalls include: (1) using a single shared LDO for AVDD and DVDD, which injects digital switching noise into the analog front end; (2) omitting the input common-mode bias, which can push the input outside the linear range; (3) failing to terminate the analog input differentially, causing reflections and degraded SNR; (4) driving the parallel CMOS outputs into an unterminated bus, leading to overshoot/undershoot. Always consult the manufacturer's reference design and follow the layout guidelines in the datasheet.
규정 준수 정보
Pb-free no-lead QFN package per Analog Devices product page. REACH and halogen-free status not specified in the verified web data and should be confirmed with the manufacturer.
