ICS342MP - 200MHz Dual-Output Clock Synthesizer | Renesas
부품 번호: ICS342MP ✓ 활성ICS342MP 개요
A clock synthesizer is a clock and timing IC that generates, divides, multiplies, or redistributes clock signals for digital logic. Clock generators and PLL-based synthesizers belong to the broader timing-control hierarchy that includes oscillators, clock buffers, dividers, and jitter-cleaning devices. Unlike a crystal oscillator, which primarily produces a fixed reference frequency, the ICS342MP uses programmable synthesis to produce multiple related output clocks and reduce the number of separate timing components in a system.
The ICS342MP combines two configurable outputs with PLL support and a maximum frequency of 200 MHz. Its input section can operate from a clock or crystal, while its LVCMOS outputs are suited to digital logic that requires single-ended clock signals. The SOIC-8 surface-mount package also supports conventional PCB assembly and provides a compact option for communication, control, and embedded-system clock trees.
Programmability allows the output frequencies to be selected through the device configuration interface instead of requiring a separate fixed-frequency oscillator for each clock domain. This can simplify board partitioning and provide a common timing reference for related circuits. The PLL architecture is useful when the system needs an output frequency derived from a common reference, although loop behavior, output jitter, and reference stability must be evaluated during clock-tree design.
Typical uses include digital controller timing, industrial automation modules, embedded processor clock distribution, communications equipment, and general-purpose peripheral clocking. In these systems, two outputs can support related clock domains or distribute a master clock to two loads while keeping the design compact. The low-voltage supply requirement should be checked against the voltage and sequencing requirements of the logic being clocked.
The main design consideration is preserving signal integrity between the synthesizer outputs and receiving logic. Keep clock traces short, provide a continuous ground reference, use appropriate termination when required, and observe the input and output timing limits in the manufacturer datasheet. Decoupling should be placed close to the supply pin, with the value and stability requirements taken directly from the recommended application circuit.
This page consolidates the ICS342MP device identity, clock-synthesis specifications, package information, sourcing structure, and application-oriented design guidance. It also identifies the verified same-family replacement candidate and separates confirmed electrical attributes from parameters that require confirmation before schematic release or production qualification.
드롭인 대체품: ICS342MP — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: ICS342MP (동일 폼 팩터 및 풋프린트) — 차이점: Architecture, Number of Outputs, PLL, Package.
ICS343MP
✅ 드롭인가격 문의
데이터시트 보기 →ICS342MP 사양
| Device Type | Clock/Frequency Synthesizer |
| Architecture | Field-programmable dual-output PLL clock synthesizer |
| Maximum Output Frequency | 200 MHz |
| Number of Circuits | 1 |
| 출력 수 | 2 |
| PLL | Yes |
| Input Types | Clock or crystal input |
| 출력 유형 | LVCMOS |
| Input-to-Output Ratio | 1:2 |
| 동작 공급 전압 | 3.15 V to 3.45 V |
| 패키지 | 8-pin SOIC, 0.154 inch body width, 3.90 mm width |
| 실장 유형 | Surface mount |
| Shipping Package | Tube |
ICS342MP tube 핀 구성 가이드
ICS342MP(tube 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: ICS342MP.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
ICS342MP 적합 용도: 6 애플리케이션s: Embedded Controller Clock Distribution, Industrial Automation Timing, Communications Module Clocking, Digital Peripheral Timing Hub, Low-Voltage Digital Logic Support, General-Purpose Synchronization.
Embedded Controller Clock Distribution
The ICS342MP suits embedded controller designs that require two related clock outputs from a common reference. Its PLL-based architecture and 200 MHz maximum output provide flexibility for processor, peripheral, or communication clock domains, while the 3.15 V to 3.45 V supply range aligns with a 3.3 V digital rail. Place the device near the receiving logic, decouple the supply pin locally, and verify configuration timing against the system clock budget.
추천
Industrial Automation Timing
The ICS342MP can organize timing in industrial automation modules where a controller, data converter, and communications section need related clocks. Two LVCMOS outputs can reduce discrete oscillator count, and the PLL provides a programmable path from a common clock or crystal source. Confirm the exact industrial temperature grade, output-jitter requirement, and long-term clock-accuracy budget before incorporating the device into a factory-control design.
추천
Communications Module Clocking
The ICS342MP is suitable for communications equipment requiring configurable local clock generation rather than separate fixed-frequency sources. Its dual outputs support parallel clock trees, the PLL permits derived frequencies, and the 200 MHz ceiling accommodates demanding digital logic. For production use, route both outputs as controlled 50-ohm single-ended paths, minimize stubs, and confirm receiver setup and hold timing at the destination device.
추천
Digital Peripheral Timing Hub
A compact control board can use the ICS342MP as a timing hub for digital peripherals that require two synchronized or related clocks. The field-programmable architecture reduces the number of fixed oscillators, while the SOIC-8 package simplifies conventional surface-mount assembly. Choose the configuration only after checking duty-cycle, phase, jitter, and frequency limits for each output; maximum frequency alone does not establish timing quality.
추천
Low-Voltage Digital Logic Support
The ICS342MP fits low-voltage digital systems operating near 3.3 V because its specified supply range is 3.15 V to 3.45 V. It can generate LVCMOS clocks for medium-performance logic without requiring a separate high-voltage clock source. Keep the device on a stable low-noise supply, place the required bypass capacitor at the power pin, and verify absolute maximum voltage limits when another rail shares the board.
추천
General-Purpose Synchronization
The ICS342MP can serve general-purpose synchronization when multiple digital subsystems need a common programmable clock source. Its clock-or-crystal input and dual LVCMOS outputs provide flexible distribution in a compact SOIC-8 package. The designer should still establish the reference accuracy, PLL configuration, output phase relationship, and worst-case jitter in the system timing budget rather than assuming equal clocks are automatically suitable for every interface.
추천
엔지니어링 참조 데이터: ICS342MP — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ICS343MP |
|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics |
| Package | 8-SOIC (0.154 inch, 3.90 mm width) | 8-SOIC (0.154 inch, 3.90 mm width) |
| Device Type | Clock/Frequency Synthesizer | Clock/Frequency Synthesizer |
| Maximum Output Frequency | 200 MHz | 200 MHz |
주요 차별점
- Dual-output programmable clock synthesis (vs ICS343MP)
- 200 MHz maximum clock capability (vs ICS343MP)
- Clock-or-crystal reference flexibility (vs ICS343MP)
- LVCMOS output integration (vs ICS343MP)
설계 노트
Route the reference and output clock traces as short, continuous paths on a solid reference plane. Avoid long stubs, test pads, and unnecessary layer transitions because they can degrade edge quality and introduce coupling into a sensitive digital clock tree. Keep the crystal, if used, close to its assigned input pins and follow the manufacturer's recommended grounding and component-placement arrangement.
Treat each LVCMOS output as a controlled transmission-line path when the trace is long, the load is capacitive, or the clock edge rate is fast. Use a continuous ground reference, maintain a practical separation from switching power nodes, and terminate according to the receiver's input characteristics. Confirm eye margin and timing behavior with an oscilloscope in the assembled design.
Do not select the ICS342MP solely from its 200 MHz maximum frequency. Verify the programmed output range, output duty-cycle limits, reference-input conditions, startup behavior, and timing uncertainty required by the receiving logic. Also confirm that the board's 3.3 V rail remains within 3.15 V to 3.45 V under load; a nominally correct supply can still exceed the permitted operating range.
Place the supply bypass capacitor immediately beside the power pin and connect it with a short return path to the ground reference. Separate the clock circuitry from noisy switching nodes and maintain short output routes. Before releasing the layout, compare every programming, reference, ground, and output connection against the pin-description table and recommended application circuit in the official Renesas datasheet.
규정 준수 정보
Exact-part environmental and material compliance declarations were not identified. Obtain the current manufacturer declarations before releasing the component into a regulated product.
