ICS551M - 1:4 160MHz CMOS Clock Buffer | Renesas
부품 번호: ICS551M ✗ 단종| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $0 | $0.00 |
| 10 | $0 | $0.00 |
| 100 | $0 | $0.00 |
| 500 | $0 | $0.00 |
| 1,000 | $0 | $0.00 |
ICS551M 개요
A clock fanout buffer is a clock-and-timing integrated circuit that distributes one incoming clock signal to multiple downstream loads. Its place in the hierarchy is clock buffer → clock fanout buffer → clock distribution IC → timing and logic semiconductor. The ICS551M helps isolate clock loads from one another, reduces loading on the source clock, and provides separate outputs for multiple sequential or peripheral circuits. This is especially useful when a single oscillator or clock source must feed several logic blocks.
Key verified characteristics include a 1:4 fanout ratio, 160 MHz maximum frequency, CMOS input and output technology, and an operating supply range of 3 V to 5.5 V. The 8-SOIC package measures 0.154 inches, or 3.90 mm, in width according to distributor data. These specifications make the device appropriate for general-purpose clock distribution where a compact surface-mount package and moderate operating frequency are sufficient.
The ICS551M belongs to the ICS ClockBlocks family and is identified by distributor listings as a low-cost, small clock buffer. Because its outputs are CMOS, the downstream circuits must be compatible with the selected supply voltage and input thresholds. The device is not a PLL, oscillator, or level shifter; its function is specifically clock replication and distribution. Designers should preserve the input and output timing relationship, maintain the required supply decoupling, and account for trace and load differences among the four outputs.
Typical applications include clock distribution in embedded control systems, digital logic networks, communications equipment, test and measurement systems, and general-purpose processor or peripheral clocking. For a design that needs more independent clock domains, frequency generation, or differential clock outputs, a different clock-and-timing device may be more appropriate. For applications requiring only one input and four CMOS copies, the ICS551M provides a straightforward distribution function in an established 8-SOIC footprint.
The main design consideration is ensuring that every connected load, trace, and voltage domain is compatible with the available 160 MHz clock. Check rise and fall-time requirements, fanout loading, power-supply noise sensitivity, and the clock-source timing margin before production release. This page synthesizes verified distributor specifications, sourcing links, package information, and engineering guidance while leaving unverified values explicitly unresolved.
The ICS551M datasheet and application information should be consulted for complete pin functions, electrical limits, timing characteristics, and recommended circuit implementation. Distributor data confirms the core identity and major specifications, but it does not provide enough evidence here to infer undocumented timing, current, or package dimensions.
드롭인 대체품: ICS551M — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
[DATA_NEEDED: verified same-package alternative 1]
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
[DATA_NEEDED: verified same-package alternative 2]
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
[DATA_NEEDED: verified same-package alternative 3]
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
[DATA_NEEDED: verified same-package alternative 4]
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
[DATA_NEEDED: verified same-package alternative 5]
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ICS551M 사양
| Product Type | Clock Fanout Buffer (Distribution) IC |
| Fanout Ratio | 1:4 |
| Maximum Frequency | 160 MHz |
| Input Technology | CMOS |
| Output Technology | CMOS |
| Supply Voltage Range | 3 V to 5.5 V |
| 출력 수 | 4 |
| Number of Inputs | 1 |
| 패키지 | 8-SOIC |
| Package Width | 0.154 in (3.90 mm) |
| 실장 유형 | Surface Mount |
| Logic Family | CMOS |
| 기능 | Single-input to four-output clock buffer |
| Product Family | ICS ClockBlocks |
ICS551M 0.154 in (3.90 mm) 핀 구성 가이드
ICS551M(0.154 in (3.90 mm) 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: ICS551M.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
ICS551M 적합 용도: 6 애플리케이션s: Embedded Control Clock Distribution, Communications Equipment Clock Fanout, Digital Logic Clock Tree, Test and Measurement Clock Systems, Processor and Peripheral Clocking, Industrial Control and Automation Logic.
Embedded Control Clock Distribution
ICS551M fits embedded control designs that already have a stable CMOS master clock but need multiple independently routed copies. Its 1:4 fanout ratio lets one source feed four logic blocks without requiring a PLL or oscillator. The verified 160 MHz maximum frequency supports moderate-speed digital systems, while the 3 V to 5.5 V range allows operation across common supply levels. Place the buffer close to the clock source when trace lengths or branch loading are significant, and route each output toward its intended load. Confirm input and output timing limits from the complete datasheet before using the device on a high-speed control bus.
추천
Communications Equipment Clock Fanout
ICS551M is appropriate for communications equipment that distributes a shared CMOS clock to multiple serial, interface, or control blocks. The four outputs help separate physical branches and reduce the electrical loading presented to the original clock source. Its 160 MHz verified ceiling provides margin for many moderate-speed digital subsystems, but the final timing budget still depends on the source waveform, trace delay, load capacitance, and receiving device requirements. Use short, well-routed clock traces and maintain a continuous ground reference. Because ICS551M is a fanout buffer rather than a jitter attenuator or PLL, retain a clean source clock and verify edge-rate requirements.
추천
Digital Logic Clock Tree
ICS551M can serve as a dedicated clock-tree element when several CMOS logic sections need separate copies of one reference signal. The 1:4 ratio provides a simple topology in which four branches can feed counters, state machines, serial engines, or peripheral control blocks. With a verified 160 MHz maximum frequency and 3 V to 5.5 V supply range, it is suitable for general-purpose logic rather than ultrafast processor clocking. Keep the input edge rate within the manufacturer's limits, place decoupling close to the device, and avoid excessive fanout capacitance on one output. Validate setup and hold timing at every receiver, especially when clock and data paths have different lengths.
추천
Test and Measurement Clock Systems
ICS551M may be used in test and measurement equipment to distribute a master reference clock to counters, capture logic, converters, or interface modules. The 1:4 architecture allows four measurement channels or timing domains to share a source without directly loading one another. The device's 160 MHz maximum frequency is useful for moderate-speed instrumentation, but measurement accuracy can still be affected by source jitter, edge rate, and trace skew. Use controlled impedance and matched routing when the clock is part of a precision timing path. The supplied verified data does not specify jitter, skew, or propagation-delay limits, so those values must be obtained from the manufacturer datasheet before precision timing use.
추천
Processor and Peripheral Clocking
ICS551M is useful when a processor or peripheral subsystem requires several copies of one CMOS clock. The single input and four outputs create a simple distribution point for processor peripherals, memory-control logic, serial engines, and supervisory circuits. The verified 3 V to 5.5 V supply range helps align the buffer with common digital rails, while the 160 MHz ceiling accommodates many embedded and control-clock requirements. Designers should verify the source clock's rise and fall times, receiver thresholds, output loading, and maximum clock frequency at the actual voltage. Avoid assuming that a fanout buffer corrects jitter, changes frequency, or provides level translation; its verified role is clock replication.
추천
Industrial Control and Automation Logic
ICS551M supports compact industrial control boards that distribute a common clock among sensor interfaces, sequencing logic, communication modules, and actuator-control circuits. Its 1:4 fanout is convenient for partitioning a clock tree across functional blocks, and the 8-SOIC package supports conventional surface-mount assembly. The verified maximum frequency of 160 MHz provides a clear upper design limit, while the 3 V to 5.5 V supply range supports common industrial logic rails when the downstream devices match. Keep clock routing away from noisy switching nodes, use a solid ground plane, and confirm that cable or sensor interfaces do not add excessive capacitive loading. Industrial temperature and EMC requirements must be checked separately because those ratings are not provided in the verified data.
추천
추천 제품 요약
엔지니어링 참조 데이터: ICS551M — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | [DATA_NEEDED: verified same-package alternative 1] | [DATA_NEEDED: verified same-package alternative 2] | [DATA_NEEDED: verified same-package alternative 3] |
|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
주요 차별점
- Simple one-to-four CMOS clock distribution (vs ICS552-01B)
- Compact 8-SOIC implementation (vs ICS552-01B)
- Moderate-speed application coverage (vs Higher-frequency clock-buffer products)
설계 노트
Route the single input clock to the ICS551M input pin with a short, direct trace, then branch the four outputs toward their respective loads. Keep clock traces away from switching power nodes, high-current return paths, and noisy digital interfaces. Because the device is a fanout buffer rather than a PLL, preserving input edge quality is important. Confirm trace length and load capacitance against the complete manufacturer timing data before enabling high-frequency operation.
Use a bypass capacitor close to the supply connection and provide a low-impedance ground reference. The verified supply range is 3 V to 5.5 V, so downstream CMOS loads must be compatible with the selected rail. Do not assume that the buffer isolates power-supply noise; clock outputs can still be affected by supply disturbances. Check the datasheet for recommended capacitance, supply-current limits, and voltage sequencing before finalizing the power architecture.
Do not use ICS551M as a frequency generator, level shifter, or PLL. It requires an incoming CMOS clock and produces four CMOS copies, so the source frequency and edge rate must already satisfy the system requirements. Also avoid treating the 160 MHz listing as a guarantee of usable system frequency without checking propagation delay, output skew, loading, and receiver timing. These parameters were not present in the supplied verified data and must be obtained from the manufacturer datasheet.
규정 준수 정보
The supplied verified web results identify the component, function, electrical basics, package, and distributor listing, but do not provide RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations. Compliance must be confirmed with Renesas or an authorized distributor. AEC-Q100 is not applicable based on the verified data.