ICS552R-01 - 200MHz 8-Output CMOS Clock Multiplier | Renesas
부품 번호: ICS552R-01 ✗ 단종ICS552R-01 개요
A clock multiplier is a clock and timing IC that accepts a reference signal, derives a higher-frequency clock, and distributes the result across multiple outputs. Within the electronics hierarchy, it belongs to clock generation and timing, then to clock and timing ICs, and finally to integrated circuits. Unlike a conventional crystal oscillator, the ICS552R-01 family can operate directly from a multiple input clock or a fundamental parallel-mode crystal, providing design flexibility for synchronous digital systems.
Key features include eight low-skew outputs, CMOS output technology, PLL capability, and operation up to 200MHz. The one-to-eight output ratio is useful when multiple logic domains require related clocks. A 3 V to 5.5 V supply range permits integration with both 3.3 V and 5 V digital systems, while the 20-SSOP surface-mount format supports compact PCB layouts. The 0°C to 70°C range applies to the identified commercial-temperature variants; other ordering codes may represent different temperature grades.
The ICS552R-01 combines clock generation, multiplication, and fan-out functions in one package. Each of the eight outputs provides a low-skew copy of the derived clock, reducing the number of separate clock-driver circuits required when several processors, FPGAs, memory devices, or communication controllers must receive related clock signals. The PLL architecture and broad maximum operating frequency make the device useful when the source clock does not directly match the required system frequency.
Typical applications include synchronous processor clock distribution, FPGA or ASIC clock fan-out, memory-controller clock distribution, communications-interface clocking, and general-purpose digital clock trees. It is especially relevant when one source must feed multiple loads while maintaining consistent frequency relationships. The device also supports systems that prefer external fundamental crystals or externally generated multiple clocks over a dedicated oscillator.
When laying out the circuit, treat all eight outputs as high-speed clock nets and follow the manufacturer’s recommended termination and decoupling arrangements. Keep clock traces short, provide a continuous ground reference, and avoid routing outputs through uncontrolled impedance discontinuities. Confirm output-drive, jitter, skew, and load-current requirements against the manufacturer datasheet before choosing series termination or a fan-out topology.
This product page combines the ICS552R-01 operating limits with practical clock-distribution guidance, ordering-code distinctions, lifecycle considerations, and a comparison framework for evaluating compatible 20-SSOP alternatives. Use the manufacturer pin-description table and electrical characteristics as the final authority for board implementation and production qualification.
드롭인 대체품: ICS552R-01 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
ICS552R-01T
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ICS552R-01IT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ICS552R-01CIT
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ICS552R-01C
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
ICS552R-01 사양
| Device Type | Clock Generator, Multiplexer, Oscillator, Multiplier, and Buffer |
| Maximum Frequency | 200 MHz |
| 출력 수 | 8 outputs |
| Input-to-Output Ratio | 1:8 |
| 출력 유형 | CMOS |
| PLL | Yes |
| Supported Inputs | Clock or crystal |
| Supply Voltage Range | 3 V to 5.5 V |
| Commercial Operating Temperature Range | 0°C to 70°C |
| 패키지 | 20-SSOP, 0.154 inch (3.90 mm) width |
| 실장 유형 | Surface mount |
| Number of Circuits | 1 |
| Differential Input | No |
ICS552R-01 20-ssop, 0.154 inch (3.90 mm) width 핀 구성 가이드
ICS552R-01(20-ssop, 0.154 inch (3.90 mm) width 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: ICS552R-01.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
ICS552R-01 적합 용도: 6 애플리케이션s: FPGA Clock Distribution, Processor Clock Fan-Out, ASIC and Memory Clock Tree, Communications Interface Clocking, Synchronous Digital Instrumentation, General-Purpose Digital Clock Tree.
FPGA Clock Distribution
The ICS552R-01 fits an FPGA clock tree that needs several related outputs from one source. Its eight low-skew CMOS outputs and 200MHz maximum frequency allow one derived clock to feed multiple FPGA clock inputs without using eight separate buffer packages. The device can accept an external clock or fundamental parallel-mode crystal and use its PLL function to produce the required multiple. In implementation, verify the selected multiplier ratio against the FPGA target frequency, keep output traces short, provide a continuous ground plane, and confirm that each output has sufficient drive for its load. The main benefit is consolidation: clock multiplication and fan-out are combined in one 20-SSOP device, although timing margin still depends on PCB loading and jitter.
추천
Processor Clock Fan-Out
The ICS552R-01 can distribute a derived clock to multiple processor, controller, or accelerator input domains. Its one-to-eight ratio provides eight low-skew copies from a clock or fundamental crystal reference, reducing the number of separate clock-driver stages in a system with several destination loads. At frequencies up to 200MHz, output-edge quality and propagation relationships become central to timing closure. Place the device close to the clock source, route outputs as controlled-impedance traces, avoid unnecessary stubs, and match output loading across branches when skew-sensitive relationships are required. The ICS552R-01 provides functional integration, but users must still validate startup, PLL lock, jitter, and source-specific timing behavior from the manufacturer datasheet.
추천
ASIC and Memory Clock Tree
The ICS552R-01 is suitable for an ASIC, FPGA, or memory subsystem that needs a multiplied clock distributed to several loads. By accepting a clock or fundamental parallel-mode crystal, it separates source selection from output distribution and can supply eight CMOS copies with low skew. The 3 V to 5.5 V supply range supports mixed 3.3 V and 5 V digital designs, subject to each load’s input thresholds. Layout should minimize output-trace length, provide local supply decoupling according to the family recommendations, and keep the clock network away from high-current switching paths. Its advantage is component consolidation; the trade-off is that a single shared clock device can become a common point of failure, making failure-mode analysis and source-quality evaluation important.
추천
Communications Interface Clocking
The ICS552R-01 can supply multiple related clocks for communications controllers, serial links, and interface logic. Its PLL capability allows a lower-frequency reference to be multiplied, while the eight low-skew outputs distribute the result to several functional blocks. This arrangement is useful when the communications subsystem needs synchronized clocks but the board cannot accommodate a separate oscillator and multiple buffer stages. Keep each clock route short and maintain consistent return paths through the ground plane to control edge degradation. Engineers should establish source-jitter and loop-bandwidth requirements before selecting a multiplier ratio, then verify the complete output timing budget through simulation and hardware measurement. The device reduces circuit count, but it does not remove the need for careful signal-integrity validation.
추천
Synchronous Digital Instrumentation
The ICS552R-01 can serve as the central clock multiplier and distributor in synchronous test, measurement, and industrial-control equipment. Eight outputs allow acquisition, processing, conversion, and communication sections to receive related clock signals from one reference. The maximum frequency of 200MHz supports demanding digital pipelines while the 20-SSOP package keeps the implementation compact. For instrumentation, separate sensitive analog sections from clock traces and use controlled return paths to prevent the eight outputs from coupling noise into sensitive nodes. Validate timing margins for the slowest and fastest specified system clocks, and qualify the selected ordering code for the instrument’s ambient-temperature range. Consolidation is valuable in multi-channel systems where board area and external clock-component count are constrained.
추천
General-Purpose Digital Clock Tree
The ICS552R-01 is useful when a board requires one stable timing reference distributed across unrelated digital blocks. Its clock or crystal input options support both external oscillator and fundamental-crystal architectures, while the 1:8 output ratio gives designers flexible fan-out. The 3 V to 5.5 V operating range makes it practical for common embedded and communications platforms. Route outputs away from noisy power-converter stages, use the manufacturer’s recommended ground and decoupling arrangement, and avoid branching clocks without accounting for edge degradation. The integrated multiplier and buffer reduce external component count and simplify clock topology. Before release, test startup behavior, lock timing, output symmetry, and the temperature extremes of the installed system, because the exact suffix determines the applicable commercial or extended-temperature grade.
추천
추천 제품 요약
엔지니어링 참조 데이터: ICS552R-01 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | ICS552R-01T | ICS552R-01IT | ICS552R-01CIT | ICS552R-01C |
|---|---|---|---|---|---|
| Package | 20-SSOP | 20-SSOP | 20-SSOP | 20-SSOP | 20-SSOP |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Number of Outputs | 8 | 8 | 8 | 8 | 8 |
| Input-to-Output Ratio | 1:8 | 1:8 | 1:8 | 1:8 | 1:8 |
| Output Type | CMOS | CMOS | CMOS | CMOS | CMOS |
| Input Type | Clock or crystal | Clock or crystal | Clock or crystal | Clock or crystal | Clock or crystal |
| PLL | Yes | Yes | Yes | Yes | Yes |
주요 차별점
- Eight-output clock multiplication and buffering in one device (vs ICS552R-01T)
- Maximum operating frequency of 200MHz (vs ICS552R-01CIT)
- 3 V to 5.5 V operating range supports common digital rails (vs ICS552R-01IT)
설계 노트
Treat the eight outputs as high-speed clock nets. Route them over a continuous ground plane, minimize stubs and unnecessary vias, and keep traces short enough to preserve edge quality at the 200MHz device limit. If a receiver requires source termination, calculate it from the actual trace impedance rather than applying a resistor by rule of thumb. Confirm output drive and load limits in the manufacturer electrical-characteristics table before adding branch points.
Use the manufacturer pin-description table to assign the 20-SSOP netlist and confirm pin 1 orientation against the package drawing. Place the device near the clock source or crystal network and keep supply and ground connections short. The available technical description does not provide a complete external-component network, so follow the family application circuit for crystal load capacitors, bypass capacitors, and termination values rather than estimating those values from the output frequency alone.
Do not assume that every ICS552R-01 suffix is electrically interchangeable solely because the package is identical. Confirm the ordering table for temperature grade, marking, and any suffix-specific configuration. Also do not assume the indexed 27 MHz value describes the maximum output capability of every ordering code; use the exact datasheet limit for the selected part. Validate PLL lock, startup, jitter, and output timing in the final reference design.
규정 준수 정보
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified for the exact ordering code. The component is a legacy clock and timing IC and is not presented as an AEC-Q100 automotive-qualified device.