Microchip Technology

KSZ9031RNXCA - 1GbE RGMII Transceiver | Microchip Technology

부품 번호: KSZ9031RNXCA ✓ 활성
1.8 V, 2.5 V, and 3.3 V Vdss 48-pin QFN, 7 mm x 7 mm Package 10 Mbps, 100 Mbps, and 1 Gbps Speed
MOQ: 1 |

KSZ9031RNXCA 개요

The Microchip Technology KSZ9031RNXCA is an automotive-qualified Gigabit Ethernet physical-layer transceiver supporting 10Base-T, 100Base-TX, and 1000Base-T operation. It provides a four-wire, full-duplex Ethernet interface with RGMII support, operates from 1.8 V, 2.5 V, and 3.3 V supplies, and is packaged in a 48-pin QFN measuring 7 mm by 7 mm. The device also includes LinkMD cable diagnostics for identifying common wiring and cable faults.

An Ethernet PHY is the physical-layer component that converts digital frames into electrical signaling for copper cables and reconstructs incoming signals for the host controller. The PHY occupies the boundary between the MAC or RGMII interface in a network processor and the transformer-coupled Ethernet cable. The KSZ9031RNXCA supports three speed levels within one integrated transceiver, allowing the same board design to accommodate 10 Mbps, 100 Mbps, and 1 Gbps links.

The KSZ9031RNXCA combines automotive qualification, LinkMD diagnostics, and RGMII integration in one compact package. Its three supported supply voltages permit compatibility with systems operating from 1.8 V, 2.5 V, or 3.3 V, while the 7 mm by 7 mm QFN construction reduces board area compared with larger Ethernet PHYs. The MODE[3:0] strap inputs establish the startup operating mode, and the RESET_N input provides a hardware reset path for initialization and system control.

Its internal organization supports copper auto-negotiation, physical coding, and reception across the IEEE speed families used for Gigabit Ethernet. A 1.2 V analog core supply is required by the device architecture and is specifically associated with pins 4 and 9. Microchip’s KSZ9031RNX hardware design checklist describes ferrite-bead isolation and both bulk and local decoupling for this rail. These implementation details are important because inadequate analog-supply filtering can degrade signal integrity or margin.

Typical applications include industrial Ethernet controllers, automotive infotainment and connectivity modules, embedded Linux platforms, industrial automation equipment, and network switches requiring one port with backward compatibility to 100Base-TX and 10Base-T. The RGMII interface reduces parallel bus complexity relative to an MII implementation while retaining deterministic host-to-PHY signaling for Gigabit throughput.

A critical design requirement is to preserve the distinction among the 1.8 V, 2.5 V, and 3.3 V supply domains and the separately generated 1.2 V analog rail. Place the prescribed bulk and high-frequency capacitors near their associated pins, keep the ferrite bead close to the AVDDL connection, and follow the manufacturer’s pin and layout guidance. External Ethernet magnetics, magnetic-interface isolation, clocking, and the selected RGMII host controller must also be designed as part of the complete interface.

This product data combines the KSZ9031RNXCA datasheet, hardware design checklist, manufacturer product page, lifecycle information, and compatible same-family conversion information with practical guidance for power partitioning, reset, diagnostics, and high-speed layout. It is intended to accelerate component selection while preserving the distinction between a confirmed pin-compatible replacement and a merely similar Ethernet transceiver.

드롭인 대체품: KSZ9031RNXCA — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

이 시리즈의 변형

다음과 드롭인 호환되는 동일 시리즈 모델: KSZ9031RNXCA (동일 폼 팩터 및 풋프린트) — 차이점: Package, Product Type, Data Rate, Auto-Negotiation, Cable Type.

Microchip Technology
Package: 48-QFN (7x7 mm) with Exposed Pad
Data Rate: 10/100/1000 Mbps (Triple Speed)
Auto-Negotiation: Yes, per IEEE 802.3 clause 28
비교 대상: KSZ9031RNXCA →
Microchip Technology
Package: 48-QFN, 7x7 mm
Product Type: Automotive Ethernet physical-layer transceiver
Auto-Negotiation: IEEE 802.3 Clause 28
비교 대상: KSZ9031RNXCA →
Microchip Technology
Package: 48-QFN
Product Type: Integrated triple-speed Ethernet physical-layer transceiver
비교 대상: KSZ9031RNXCA →
Microchip Technology
Package: 48-pin QFN (7x7 mm)
Product Type: Ethernet Physical Layer Transceiver (PHY)
Data Rate: 10 / 100 / 1000 Mbps (triple-speed)
비교 대상: KSZ9031RNXCA →
Microchip Technology
Package: 48-QFN (7x7 mm)
Product Type: Ethernet Transceiver (PHY)
Data Rate: 10/100/1000 Mbps
비교 대상: KSZ9031RNXCA →
Microchip Technology
Package: 48-pin QFN (7x7 mm) with EPAD
Product Type: Ethernet Transceiver (PHY)
Data Rate: 10 Mbps / 100 Mbps / 1000 Mbps
비교 대상: KSZ9031RNXCA →
Microchip Technology
Package: 48-pin QFN (7x7 mm) with Exposed Pad
Product Type: Ethernet Physical Layer Transceiver (PHY)
Data Rate: 10/100/1000 Mbps (Triple-Speed)
비교 대상: KSZ9031RNXCA →

KSZ9031RNXIA

✅ 드롭인 ⚠️ 사양 미검증
Microchip Technology
📦 48-QFN (7x7 mm)
Ethernet Transceiver (PHY) · 10/100/1000 Mbps · 10Base-T, 100Base-TX, 1000Base-T · RGMII · 1 Port · 1.8V / 2.5V / 3.3V · 3.3V · CAT-5 UTP

가격 문의

데이터시트 보기 →

KSZ9031RNXIC

✅ 드롭인
Microchip Technology
📦 48-QFN (7x7 mm)
Ethernet Physical Layer Transceiver (PHY) · 10/100/1000 Mbps (Triple-Speed) · IEEE 802.3 10BASE-T / 100BASE-TX / 1000BASE-T · RGMII (version 2.0, on-chip delay) · 4/4 Transceiver (Full Duplex) · 1.8 V / 2.5 V / 3.3 V · 48-pin QFN (7x7 mm) with Exposed Pad · CAT-5 Unshielded Twisted Pair (UTP)

가격 문의

데이터시트 보기 →

KSZ9031RNXCC

✅ 드롭인
Microchip Technology
📦 48-QFN (7x7 mm)
Ethernet Physical Layer Transceiver (PHY) · 10 / 100 / 1000 Mbps (triple-speed) · IEEE 802.3, 802.3u, 802.3ab, 802.3az (EEE) · RGMII (Version 2.0 compliant, on-chip delay) · 4 differential pairs, CAT-5 UTP, 100-ohm differential · MDIO / MDC (IEEE 802.3 clause 22/45) · 3.3 V · 1.2 V (on-chip LDO controller + external MOSFET)

가격 문의

데이터시트 보기 →

KSZ9031RNXCA 사양

Product Type Gigabit Ethernet physical-layer transceiver
Supported Speeds 10 Mbps, 100 Mbps, and 1 Gbps
Supported Ethernet Modes 10Base-T, 100Base-TX, and 1000Base-T
Host Interface RGMII
Data Path 4-wire full-duplex Ethernet
Supply Voltage Options 1.8 V, 2.5 V, and 3.3 V
Analog Core Supply 1.2 V
패키지 48-pin QFN, 7 mm x 7 mm
실장 유형 Surface mount
Cable Diagnostics LinkMD
Time-Domain Reflectometry Diagnostics Supported TDR-based cable testing
Mode Configuration MODE[3:0] strap inputs
Hardware Reset Input RESET_N, pin 42
Automotive Qualification Automotive qualified
AVDDL Bulk Capacitance 10 uF
AVDDL Local Decoupling 0.1 uF per AVDDL pin
AVDDL Ferrite Bead Impedance 100 ohm to 220 ohm at 100 MHz

KSZ9031RNXCA 48-pin qfn, 7 mm x 7 mm 핀 구성 가이드

KSZ9031RNXCA(48-pin qfn, 7 mm x 7 mm 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.

KSZ9031RNXCA의 48-pin qfn, 7 mm x 7 mm 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: KSZ9031RNXCA.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

KSZ9031RNXCA 적합 용도: 6 애플리케이션s: Automotive Ethernet Connectivity, Industrial Automation Ethernet, Embedded Linux Network Platform, Industrial Network Switch Port, Test and Measurement Instrumentation, Network Security Gateway.

🚗

Automotive Ethernet Connectivity

The KSZ9031RNXCA fits an automotive Ethernet port that must support 10Base-T, 100Base-TX, and 1000Base-T while communicating with an RGMII-capable host controller. Its automotive-qualified status, 48-pin 7 mm by 7 mm QFN package, and 1.8 V, 2.5 V, or 3.3 V supply options support compact vehicle-networking designs. LinkMD and TDR-based diagnostics can help installation and service teams locate cable or connector faults. The design must implement the separate 1.2 V analog rail, ferrite-bead isolation, local decoupling, Ethernet magnetics, and all layout requirements from the manufacturer’s hardware design checklist.

🏭

Industrial Automation Ethernet

The KSZ9031RNXCA is suitable for industrial controllers that must connect to 10 Mbps, 100 Mbps, and 1 Gbps Ethernet equipment through one RGMII interface. Backward-compatible speed support helps bridge older supervisory stations, sensors, and production equipment while preserving a path to Gigabit bandwidth. The integrated LinkMD and TDR-based diagnostics provide useful installation and maintenance information in cabinets where cable faults can be difficult to diagnose. Power planning must account for the 1.2 V analog core rail, while the compact 7 mm by 7 mm QFN package helps preserve board area in densely populated industrial control equipment.

🖥️

Embedded Linux Network Platform

The KSZ9031RNXCA can serve as the Gigabit copper-network interface in an embedded Linux platform whose host processor exposes RGMII. Supporting 10Base-T through 1000Base-T allows one physical design to connect to development networks, management systems, and high-throughput industrial or server links. The RGMII interface limits parallel data-path wiring compared with older MII arrangements, while LinkMD diagnostics provide link and cable-status information to the network driver. Designers should use strap-selected operating modes, the active-low RESET_N input, the prescribed analog-rail filtering, and a high-speed layout that minimizes noise and timing margin loss.

🌐

Industrial Network Switch Port

The KSZ9031RNXCA supports a copper switch port that must negotiate among 10 Mbps, 100 Mbps, and 1 Gbps links. Its RGMII host connection suits switching silicon with a compatible parallel interface, while the small 48-pin QFN package allows multiple ports to be placed on a space-constrained board. The device’s three supported supply voltages provide flexibility across different digital logic domains, but each rail still requires correct sequencing and decoupling. LinkMD and TDR-based cable diagnostics can help managed-network equipment report installation faults and distinguish remote-end problems from local PHY problems during commissioning.

🔧

Test and Measurement Instrumentation

The KSZ9031RNXCA can provide a backward-compatible Gigabit Ethernet connection in instruments that exchange data with workstations, test systems, or service tools. A single PHY supporting 10Base-T, 100Base-TX, and 1000Base-T lets the instrument connect reliably to older laboratory infrastructure as well as high-speed networks. LinkMD can provide link and cabling information, while TDR-based diagnostics offer additional fault-localization capability. The implementation should isolate the 1.2 V analog core supply with the manufacturer-recommended ferrite bead and place both 10 uF bulk and 0.1 uF local capacitors close to their assigned pins.

🧩

Network Security Gateway

The KSZ9031RNXCA fits security gateways and network appliances that need a copper Gigabit Ethernet port with compatibility for slower legacy devices. RGMII provides a deterministic host interface, and support for 10Base-T, 100Base-TX, and 1000Base-T broadens deployment flexibility in mixed enterprise and industrial environments. Diagnostic functions can assist field technicians with link establishment and cable-fault troubleshooting. Careful partitioning of the 1.8 V, 2.5 V, 3.3 V, and 1.2 V supply domains is necessary to prevent digital activity from coupling into sensitive analog circuits, while controlled clocking and short, impedance-managed RGMII routes protect signal integrity.

What are the key specifications of KSZ9031RNXCA that engineers should know?
The KSZ9031RNXCA is a 1 Gbps Ethernet PHY supporting 10Base-T, 100Base-TX, and 1000Base-T with RGMII. According to the Microchip Technology KSZ9031RNX datasheet DS00002117J, the device is automotive qualified, accepts 1.8 V, 2.5 V, or 3.3 V supplies, includes a 1.2 V analog core rail, and uses a 48-pin 7 mm by 7 mm QFN package. LinkMD and TDR-based diagnostics help identify copper-cable and installation faults.
What is the operating voltage of the KSZ9031RNXCA?
The KSZ9031RNXCA supports 1.8 V, 2.5 V, and 3.3 V operating supplies. The manufacturer datasheet also identifies a 1.2 V analog core supply, with AVDDL pins 4 and 9 serving that rail. These voltage domains should not be treated as interchangeable: use the schematic and pin-description table for the correct connection of digital, analog, and I/O supply pins.
What Ethernet speeds does KSZ9031RNXCA support?
The KSZ9031RNXCA supports 10 Mbps, 100 Mbps, and 1 Gbps operation. According to the Microchip Technology KSZ9031RNX datasheet, those rates correspond to 10Base-T, 100Base-TX, and 1000Base-T, respectively. Automatic speed negotiation allows a single Ethernet port to connect across legacy 10 Mbps and 100 Mbps equipment as well as Gigabit networks.
Where can I download the KSZ9031RNXCA datasheet PDF?
The official KSZ9031RNXCA datasheet PDF is available from Microchip Technology as document DS00002117J. The manufacturer document is the preferred source for the complete pin description, electrical characteristics, operating modes, strap behavior, and timing information. Use the manufacturer PDF when assigning PCB nets or validating a design, and use the separate KSZ9031RNX hardware design checklist for layout and power-supply recommendations.
Where can I find the KSZ9031RNXCA pinout?
The KSZ9031RNXCA pinout is presented in the Microchip Technology KSZ9031RNX datasheet DS00002117J. The device uses a 48-pin QFN package, and the manufacturer identifies RESET_N at pin 42 and AVDDL at pins 4 and 9. Use the package drawing and pin-description table for every signal, especially exposed-pad, supply, strap, clock, and RGMII connections.
Does the KSZ9031RNXCA support RGMII and LinkMD diagnostics?
Yes, the KSZ9031RNXCA supports RGMII and includes LinkMD cable diagnostics. The manufacturer identifies the part as a Gigabit Ethernet transceiver with RGMII support and as an automotive-qualified triple-speed PHY. LinkMD provides cable-status information, while the part’s TDR-based diagnostics can assist with locating faults in cabling and network installation.
What can replace the KSZ9031RNXCA?
The KSZ9031RNXIC and KSZ9031RNXCC are confirmed same-family replacements for the KSZ9031RNXCA, and Microchip documents the RNXIA, RNXCA, RNXIC, and RNXCC conversion path. Their use should be checked against the product-change information for automotive qualification, temperature range, ordering code, and production status. The same 48-pin QFN land pattern does not by itself confirm that every procurement or qualification requirement is identical.
What is the best Microchip replacement for KSZ9031RNXCA?
The best documented Microchip replacement candidates are KSZ9031RNXIC and KSZ9031RNXCC because Microchip publishes a conversion path involving KSZ9031RNXIA and KSZ9031RNXCA. Both retain the KSZ9031RNX family identity and are associated with the same 48-pin QFN implementation. Final qualification should confirm temperature grade, automotive status, lifecycle, and exact ordering information against the intended production program.
Is KSZ9031RNXCA suitable for automotive Ethernet applications?
Yes, the KSZ9031RNXCA is identified by Microchip as an automotive-qualified Ethernet PHY. Its integrated 10Base-T, 100Base-TX, and 1000Base-T support, RGMII host interface, LinkMD diagnostics, and TDR-based cable testing make it suitable for connected-vehicle and industrial Ethernet designs. Automotive programs must still verify the exact ordering code, temperature grade, qualification status, and production requirements.
When should I choose KSZ9031RNXCA over another Ethernet PHY?
Choose the KSZ9031RNXCA when a design needs one PHY to support 10Base-T, 100Base-TX, and 1000Base-T through RGMII in an automotive-qualified 48-pin QFN. It is especially useful when LinkMD and TDR-based diagnostics add installation value. Select another PHY only when its regulatory approval, power architecture, media support, host timing, package, or diagnostic features better match a non-automotive or non-RGMII design.
KSZ9031RNXCA vs KSZ9031RNXIC — which is better for an automotive design?
KSZ9031RNXCA and KSZ9031RNXIC belong to the same KSZ9031RNX family and are covered by a Microchip conversion notice. The KSZ9031RNXCA is automotive qualified according to the manufacturer product page, while the exact qualification and temperature details of RNXIC must be confirmed for the selected ordering code. For an automotive release, compare the current product-change notices and quality-document requirements before substitution.
How should the 1.2 V AVDDL rail be implemented for KSZ9031RNXCA?
The 1.2 V AVDDL rail should be generated through the recommended ferrite-bead isolation arrangement and local decoupling. Microchip’s hardware design checklist specifies a generally suitable 100 ohm to 220 ohm ferrite bead at 100 MHz, a 10 uF bulk capacitor, and 0.1 uF local decoupling at each AVDDL pin. Place these components close to the device and preserve the ground-return path to minimize analog-supply noise.
What is the difference between the KSZ9031RNXCA and KSZ9031MNXIC?
The KSZ9031RNXCA is a 48-pin 7 mm by 7 mm QFN device, while the KSZ9031MNXIC belongs to a different KSZ9031 package option described as 100-pin and 12 mm by 12 mm. Their physical land patterns are therefore not interchangeable. Although both serve the same triple-speed Ethernet PHY family, the KSZ9031RNXIC is the appropriate same-footprint consideration, not the MNXIC.
Where can I buy KSZ9031RNXCA and what is its current lead time?
Use the Request a Quote form on this page to ask about KSZ9031RNXCA pricing, stock, minimum order quantity, and production lead time. The quote team can confirm the exact 48-pin 7 mm by 7 mm QFN ordering code, including tray or tape-and-reel packaging requirements, without tying the answer to a changing distributor price. Current lead time depends on inventory, scheduled production, and the requested quantity.
Is KSZ9031RNXCA in stock, and how much does it cost?
Current KSZ9031RNXCA availability and pricing are handled through the Request a Quote form on this page. Request the exact MPN, required package shipping format, and target quantity so the quote can reflect the correct variant. The device is an active catalog product with automotive-qualified Ethernet PHY functionality, but operational stock and commercial terms can change independently of the component’s technical lifecycle.

엔지니어링 참조 데이터: KSZ9031RNXCA — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose KSZ9031RNXCA for an automotive or industrial copper Ethernet port that needs backward-compatible 10Base-T, 100Base-TX, and 1000Base-T operation through RGMII. Its 48-pin 7 mm by 7 mm QFN package, three supply-voltage options, LinkMD diagnostics, and TDR-based cable testing form a strong combination for compact, serviceable network equipment. KSZ9031RNXIC and KSZ9031RNXCC are documented same-family conversion candidates when procurement or lifecycle conditions change, but their exact automotive, temperature, and qualification terms must be checked for the selected ordering code. KSZ9031RNXIA is another same-family option with an identical package family, subject to the same qualification review. Do not use KSZ9031MNXIC as a drop-in choice because its 100-pin, 12 mm by 12 mm package requires a different PCB footprint. For non-RGMII, non-automotive, or differently regulated designs, evaluate another PHY only after checking media support, supply architecture, host timing, diagnostics, and package compatibility.

대체품과의 비교

파라미터 이 제품 KSZ9031RNXIA KSZ9031RNXIC KSZ9031RNXCC
Package 48-QFN (7x7 mm) 48-QFN (7x7 mm) 48-QFN (7x7 mm) 48-QFN (7x7 mm)
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Maximum Data Rate 1 Gbps 1 Gbps 1 Gbps 1 Gbps
Supported Ethernet Modes 10Base-T, 100Base-TX, 1000Base-T 10Base-T, 100Base-TX, 1000Base-T 10Base-T, 100Base-TX, 1000Base-T 10Base-T, 100Base-TX, 1000Base-T
Host Interface RGMII RGMII RGMII RGMII
Operating Supply Options 1.8 V, 2.5 V, 3.3 V 1.8 V, 2.5 V, 3.3 V 1.8 V, 2.5 V, 3.3 V 1.8 V, 2.5 V, 3.3 V
Analog Core Supply 1.2 V 1.2 V 1.2 V 1.2 V
Cable Diagnostics LinkMD and TDR-based diagnostics LinkMD and TDR-based diagnostics LinkMD and TDR-based diagnostics LinkMD and TDR-based diagnostics
Mode Configuration MODE[3:0] strap inputs MODE[3:0] strap inputs MODE[3:0] strap inputs MODE[3:0] strap inputs

주요 차별점

  • Integrated triple-speed support (vs KSZ9031RNXIC)
  • Cable-fault diagnostics are integrated (vs KSZ9031RNXCC)
  • Compact multi-voltage PHY footprint (vs KSZ9031MNXIC)

설계 노트

Implement the 1.2 V AVDDL rail exactly as described in Microchip’s KSZ9031RNX hardware design checklist. Pins 4 and 9 use a generally suitable 100 ohm to 220 ohm ferrite bead at 100 MHz. Place a 10 uF bulk capacitor on the supply line, add 0.1 uF local decoupling at each AVDDL pin, and install bulk capacitance on both sides of the bead. Keep the analog ground return short and isolated from high-current switching paths so digital supply activity does not disturb the PHY’s analog core.

Follow the manufacturer’s KSZ9031RNX layout and grounding guidance for the 48-pin QFN, particularly the exposed thermal pad, RGMII nets, clock input, and analog supply. Place decoupling capacitors directly beside their associated pins and minimize loop area. Keep the RGMII interface short, provide a continuous ground reference, and use controlled-impedance routing where the host and PHY operate at their specified signaling rates. Avoid routing sensitive analog or clock nets beneath noisy digital and power-conversion sections.

Do not substitute a 100-pin KSZ9031MNXIC for this 48-pin RNX device. The MNXIC uses a different 12 mm by 12 mm package and therefore a different PCB land pattern. The RNXIA, RNXCA, RNXIC, and RNXCC ordering-code conversion also does not automatically transfer a product qualification decision; review temperature grade, automotive status, lifecycle, and production notices before approving a substitution.

Treat RESET_N, MODE[3:0], the reference clock, and RGMII as controlled interface signals rather than ordinary logic. Observe the datasheet’s strap levels and reset timing because incorrect strap values can select an unintended startup mode or keep the device in a special power-down state. Confirm the host clock and RGMII timing configuration before release, and validate the completed board for signal margin, impedance, crosstalk, and radiated emissions rather than relying only on schematic connectivity.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Qualified
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

Microchip identifies the KSZ9031 as automotive qualified. Detailed RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations for the exact ordering code require confirmation from the manufacturer.

관련 검색

ksz9031rnxca datasheet KSZ9031RNXCA datasheet PDF KSZ9031RNXCA pinout KSZ9031RNXCA RGMII Ethernet PHY KSZ9031RNXCA 48-QFN pinout KSZ9031RNXCA drop-in replacement KSZ9031RNXCA equivalent KSZ9031RNXCA vs KSZ9031RNXIC KSZ9031RNXCA automotive Ethernet KSZ9031RNXCA hardware design checklist KSZ9031RNXCA price KSZ9031RNXCA stock Microchip KSZ9031RNXCA KSZ9031RNXCA LinkMD diagnostics KSZ9031RNXCA AVDDL layout

관련 부품 & 용어

Microchip Technology KSZ9031RNXCA KSZ9031RNXIA KSZ9031RNXIC KSZ9031RNXCC KSZ9031 Gigabit Ethernet PHY Ethernet physical layer Ethernet transceiver RGMII 10Base-T 100Base-TX 1000Base-T LinkMD TDR cable diagnostics 48-QFN QFN package family surface-mount package automotive qualified Ethernet magnetics MODE[3:0] RESET_N AVDDL 1.2 V analog core supply ferrite-bead isolation
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기