LC4384B-5T176C - 384-Macro 5 ns ISP CPLD | Lattice
부품 번호: LC4384B-5T176C ✗ 단종LC4384B-5T176C 개요
A complex programmable logic device, or CPLD, belongs to the programmable-logic hierarchy alongside FPGAs. Unlike an FPGA, a CPLD uses non-volatile configuration memory to retain its logic immediately after power-up without a separate configuration PROM or processor boot sequence. Its predictable interconnect and deterministic propagation behavior make it useful where timing predictability, low-latency boot, and simple in-circuit reprogramming are more important than very high logic density.
The LC4384B provides 384 macrocells in a 176-lead TQFP package and is identified by the -5 speed grade. Its SuperFAST architecture targets high-performance combinational and sequential logic, while in-system programming allows the same board to support field updates. Programming at 3.3 V, 2.5 V, or 1.8 V broadens its usefulness in systems that operate from mixed-voltage rails or use a lower-voltage controller during configuration.
The B-series LC4384 device family offers alternatives with different speed grades, temperature options, and package variants. Exact timing, current, and operating-temperature limits should be confirmed against the Lattice device datasheet and the specific ordering code before placing a new production order, because this family has been discontinued and remaining units are generally legacy inventory rather than a current design-in recommendation.
Typical uses include industrial control interfaces, peripheral bridging, legacy storage-controller glue logic, communications front ends, test and measurement equipment, and embedded system support functions. In each case, the device consolidates multiple gates and flip-flops into one package while retaining deterministic logic operation after power restoration.
Designers should preserve the original LC4384B footprint, pin assignments, configuration interface, and programming voltage when qualifying a direct replacement. Review the pin-description table in the manufacturer datasheet before assigning PCB tracks, and confirm that any substitute device supports the required I/O voltage and operating-temperature range. For new designs, compare the CPLD with current low-cost FPGA or microcontroller solutions because LC4384B availability is constrained by its discontinued lifecycle status.
This page combines verified part identification, package and lifecycle information, drop-in family alternatives, engineering application guidance, and a design-level comparison so engineers can assess reuse and sourcing risk before committing to a board revision.
드롭인 대체품: LC4384B-5T176C — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: LC4384B-5T176C (동일 폼 팩터 및 풋프린트) — 차이점: Device Type, Package, Architecture, Configuration Memory, Package Type.
LC4384B-5TN176C
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
LC4384B-5T176I
✅ 드롭인가격 문의
데이터시트 보기 →LC4384C-5T176C
✅ 드롭인가격 문의
데이터시트 보기 →LC4384B-75T176C
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
LC4384B-35T176C
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
LC4384V-5T176C
✅ 드롭인가격 문의
데이터시트 보기 →LC4384B-5T176C 최대 정격 & 전기적 특성
| Device Type | SuperFAST high-density complex programmable logic device (CPLD) |
| Logic Macrocell Count | 384 macrocells |
| Speed Grade | 5 ns |
| Configuration Support | In-system programmable (ISP) |
| Programmable Supply Voltage | 3.3 V, 2.5 V, or 1.8 V |
| Package Type | 176-lead TQFP |
| Package Designation | TQFP-176 |
| 실장 유형 | Surface mount |
| Configuration Memory | Non-volatile configuration memory |
| Architecture | SuperFAST high-density PLD architecture |
| 수명 주기 상태 | Discontinued |
| Device Family | LC4384B |
LC4384B-5T176C tqfp-176 핀 구성 가이드
LC4384B-5T176C(tqfp-176 패키지)의 핀 구성입니다. 이 디지털 IC에는 GPIO, 통신 인터페이스(UART, SPI, I2C), 전원 핀이 포함되어 있습니다. 대체 핀 기능과 구성 옵션은 제조사 데이터시트를 참조하십시오. 임베디드 시스템 설계와 PCB 레이아웃에 필수적입니다.
다음에 대한 상세 핀아웃 데이터 없음: LC4384B-5T176C.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
LC4384B-5T176C 적합 용도: 6 애플리케이션s: Industrial Control and Automation Logic, Peripheral Bus Bridging and Glue Logic, Test and Measurement Front Ends, Communications Interface Consolidation, Legacy Storage and Printer Controllers, Embedded System Support Logic.
Industrial Control and Automation Logic
The LC4384B-5T176C fits legacy industrial controllers that need substantial combinational and sequential logic close to the processor. Its 384 macrocells can consolidate state machines, interlock checks, signal conditioning, and peripheral command sequencing without relying on a separate FPGA. The 5 ns speed grade provides a deterministic timing target, while non-volatile configuration allows operation immediately after power restoration. The 176-lead TQFP also offers enough I/O for multi-bit buses and multiple isolated control outputs. For an industrial temperature requirement, verify whether the original design specifies the commercial or industrial suffix and preserve the footprint and pin functions during any substitution.
추천
Peripheral Bus Bridging and Glue Logic
Use the LC4384B-5T176C when a microprocessor must interface with several legacy peripherals having different bus widths, timing requirements, or signal formats. The device's 384 macrocells provide enough capacity for address decoding, byte-lane steering, interrupt arbitration, and protocol conversion in one package. Its 5 ns speed grade is useful for registered pipeline stages and short combinational paths, while the non-volatile configuration avoids a boot-time bitstream load. Because the LC4384B family is discontinued, legacy board maintenance is a strong use case, but new designs should also evaluate current CPLD or microcontroller peripherals that integrate the bridging function.
추천
Test and Measurement Front Ends
The LC4384B-5T176C can implement deterministic control logic for laboratory and industrial test equipment, including sequencer timing, instrument bus arbitration, trigger routing, and status decoding. Its 5 ns speed class supports short synchronous pipelines and helps maintain repeatable measurement sequences. In-system programmability allows different test profiles to be loaded without removing the device, and the non-volatile architecture simplifies recovery after instrument power cycling. The 176-lead TQFP provides a practical route for a high pin count on older boards. When maintaining such equipment, confirm the pin-description table and configuration interface before fitting a different suffix or revision.
추천
Communications Interface Consolidation
The LC4384B-5T176C is suitable for legacy communications equipment that requires line-interface adaptation, parallel-to-serial conversion, packet framing, and flow-control logic. Its 384 macrocells allow several interface channels and their control state machines to share one CPLD, reducing the number of separate glue-logic packages. The 5 ns grade supports registered transfers and short combinational stages, while 3.3 V, 2.5 V, and 1.8 V in-system programming options help align configuration with the surrounding control system. Verify the I/O voltage ratings and maximum operating frequency in the family datasheet, particularly if the equipment uses older 5 V or 3.3 V interfaces.
추천
Legacy Storage and Printer Controllers
The LC4384B-5T176C can serve as the control CPLD in older printers, scanners, storage systems, and embedded peripherals where a deterministic command sequencer is required. The 384-macrocell device can host DMA-style state machines, data validation, status generation, and motor or actuator timing. The 176-lead TQFP provides ample connections for buses and discrete control signals, and the non-volatile configuration supports rapid recovery after power cycling. For repair and redesign work, retain the original programming algorithm and JTAG or ISP wiring because the footprint alone does not guarantee configuration compatibility with every revision suffix.
추천
Embedded System Support Logic
The LC4384B-5T176C is useful for adding dedicated hardware logic around a microprocessor, including watchdog timers, DMA request generation, interrupt controllers, and specialized data-format conversion. Its deterministic architecture can offload time-critical paths from a shared microcontroller bus, while the 5 ns speed grade provides useful timing margin for registered logic. In-system programming permits production test and field configuration without replacing the package, and the 176-lead TQFP simplifies adaptation to older boards with abundant external I/O. For new embedded platforms, compare this approach with integrating the function into a microcontroller or current low-cost FPGA before committing additional board area.
추천
추천 제품 요약
엔지니어링 참조 데이터: LC4384B-5T176C — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | LC4384B-5TN176C | LC4384B-5T176I | LC4384C-5T176C | LC4384B-75T176C |
|---|---|---|---|---|---|
| Brand | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor |
| Package | TQFP-176 | TQFP-176 - same | TQFP-176 - same | TQFP-176 - same | TQFP-176 - same |
| Device Type | SuperFAST high-density CPLD | LC4384B high-density CPLD | LC4384B high-density CPLD | LC4384C high-density CPLD | LC4384B high-density CPLD |
| Logic Macrocell Count | 384 macrocells | 384 macrocells | 384 macrocells | 384 macrocells | 384 macrocells |
| Speed Grade | 5 ns | 5 ns | 5 ns | 5 ns | 7.5 ns |
| In-System Programming | Supported | Supported | Supported | Supported | Supported |
| Programmable Supply Voltage | 3.3 V, 2.5 V, or 1.8 V | 3.3 V, 2.5 V, or 1.8 V | 3.3 V, 2.5 V, or 1.8 V | 3.3 V, 2.5 V, or 1.8 V | 3.3 V, 2.5 V, or 1.8 V |
| Temperature Grade Designation | Commercial suffix designation | N suffix designation | Industrial suffix designation | Commercial suffix designation | Commercial suffix designation |
| Lifecycle Status | Discontinued | Legacy LC4384 family | Legacy LC4384 family | Legacy LC4384 family | Legacy LC4384 family |
주요 차별점
- Exact 5 ns speed option (vs LC4384B-75T176C)
- Matching capacity and package in a sourcing alternative (vs LC4384B-5TN176C)
- Industrial suffix option for temperature-sensitive service (vs LC4384B-5T176C)
설계 노트
Treat the 176-lead TQFP footprint as a fixed mechanical and electrical constraint. Preserve the original pin assignments, power-grid connections, decoupling locations, and configuration interface when replacing the device on an existing board. Because the library used for package diagrams does not include a dedicated 176-lead key, the diagram is rendered as a generic package; use the manufacturer pin-description table and land pattern for all production artwork.
Do not select a replacement solely because the LC4384B family name matches. The -5 and -7.5 suffixes identify different speed grades, while the B, C, I, N, and V suffixes distinguish ordering or revision options. A 7.5 ns device can reduce timing margin by 50% relative to a 5 ns device, so rerun static timing analysis and confirm temperature grade, configuration compatibility, and programming voltage before substitution.
Follow the power-supply and decoupling recommendations in the Lattice family datasheet for the 3.3 V, 2.5 V, and 1.8 V configuration options. Keep configuration and normal operating supply pins properly biased, provide local high-frequency bypass capacitance, and avoid connecting programming signals to pins whose voltage level differs from the selected configuration supply.
Verify that the ISP cable, algorithm, and configuration file remain valid for the exact device revision. A footprint-compatible part can still require a different configuration algorithm if the silicon revision or ordering suffix differs. For production repair and long-term maintenance programs, archive the programmed configuration file, schematic, pin table, and device marking together with each purchased lot.
규정 준수 정보
The device is a discontinued industrial programmable-logic component and is not an automotive-qualified part. Compliance declarations for the exact historical ordering code are not stated in the available product listings and require confirmation from the manufacturer or the distributor handling the traceable inventory.