LM239DG - 3-36V Quad Comparator | onsemi | SOIC-14
부품 번호: LM239DG ✗ 단종LM239DG 개요
A quad analog comparator is a multi-channel semiconductor that compares two input voltages and produces a logic-level indication of their relationship. The LM239DG belongs to the comparator hierarchy within analog and mixed-signal integrated circuits, where it is used for voltage thresholding, signal conditioning, and protection functions. Its four channels share one package but operate independently, allowing a compact design to implement several sensing points without using four separate comparator devices.
Key features include four general-purpose comparator elements, single-supply operation from 3 V to 36 V, support for ±1.5 V to ±18 V dual-supply rails, and outputs compatible with CMOS, open-collector, and TTL loads. The typical input offset voltage is listed as no more than 1.3 mV, while the typical input bias current is 25 nA. These characteristics make the device suitable for precision threshold detection where input current must not materially disturb a high-impedance source.
The comparator architecture translates the voltage relationship between each noninverting and inverting input into an open-collector output state. Because the outputs are open collector, external pull-up resistors are required for normal logic-high operation. Each output can sink the stated 130 mV typical saturation voltage at a 4 mA load. This arrangement provides flexible voltage-level adaptation, although pull-up selection, output rise time, and system fanout must be considered during design.
Typical applications include consumer and industrial level detection, low-level sensing, memory-device threshold monitoring, automotive interface circuits, and general-purpose signal conditioning. The four channels can monitor separate sensor lines, compare a control signal against adjustable references, or implement window-detection functions using external resistor networks. The 3 V minimum supply also permits operation from regulated 5 V or 12 V systems, while the 36 V maximum supports higher-voltage industrial rails when the input and output limits permit.
The principal design consideration is protecting every input and output from voltages outside the device ratings, especially during power sequencing. Place the pull-up resistor close to each open-collector output, route sensitive input traces away from switching nodes, and verify logic thresholds against the actual pull-up voltage. A common 14-Pin SOIC footprint also simplifies assembly, but the obsolete lifecycle status requires lifecycle confirmation before committing a new production design.
This product page combines the LM239DG electrical characteristics, package details, replacement analysis, and practical design guidance with direct quotations and procurement requests routed through the XAIPART Request a Quote form. It helps engineers evaluate a legacy comparator without relying on incomplete distributor summaries.
드롭인 대체품: LM239DG — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: LM239DG (동일 폼 팩터 및 풋프린트) — 차이점: Comparator Type, Package, Output Type, Logic Compatibility, Number of Channels.
LM239DR
✅ 드롭인가격 문의
데이터시트 보기 →LM239DR2G
✅ 드롭인가격 문의
데이터시트 보기 →LM239DT
✅ 드롭인가격 문의
데이터시트 보기 →LM339DR
✅ 드롭인✓ 재고 있음
$0.0738 / 개
데이터시트 보기 →LM239DG 최대 정격 & 전기적 특성
| Comparator Type | General-purpose differential comparator |
| Number of Elements | 4 comparators |
| Supply Voltage Range | 3 V to 36 V |
| Dual-Supply Voltage Range | -18 V to +18 V |
| 출력 유형 | Open collector with CMOS, open-collector, and TTL compatibility |
| Typical Low Output Saturation Voltage | 130 mV at 4 mA |
| Typical Input Bias Current | 25 nA |
| Typical Input Offset Current | +/-5 nA |
| Maximum Input Offset Voltage | 1.3 mV |
| 동작 온도 범위 | -25 C to +85 C |
| 패키지 | 14-pin SOIC |
| Package Width | 3.90 mm |
| Lead Pitch | 0.154 mm |
| Supply Configuration | Single supply or dual supply |
| 실장 유형 | Surface mount |
LM239DG 핀 구성
| 핀 1 | OUT1 — Comparator 1 open-collector output |
| 핀 2 | IN1- — Comparator 1 inverting input |
| 핀 3 | IN1+ — Comparator 1 noninverting input |
| 핀 4 | GND — Ground connection |
| 핀 5 | IN2+ — Comparator 2 noninverting input |
| 핀 6 | IN2- — Comparator 2 inverting input |
| 핀 7 | OUT2 — Comparator 2 open-collector output |
| 핀 8 | OUT3 — Comparator 3 open-collector output |
| 핀 9 | IN3- — Comparator 3 inverting input |
| 핀 10 | IN3+ — Comparator 3 noninverting input |
| 핀 11 | VCC — Positive supply connection |
| 핀 12 | IN4+ — Comparator 4 noninverting input |
| 핀 13 | IN4- — Comparator 4 inverting input |
| 핀 14 | OUT4 — Comparator 4 open-collector output |
일반적인 애플리케이션
LM239DG 적합 용도: 6 애플리케이션s: Industrial Level Detection, Low-Level Sensing, Memory Threshold Monitoring, Automotive Interface Circuits, Consumer Equipment Thresholding, Sensor Signal Conditioning.
Industrial Level Detection
The LM239DG fits industrial level-detection circuits because four independent channels can compare sensor voltages against reference levels within a 3 V to 36 V supply environment. Its maximum input offset voltage of 1.3 mV and typical input bias current of 25 nA help limit threshold errors when the sensed signal has a high source impedance. Each open-collector output can drive a pull-up and an alarm or PLC input, with a listed typical saturation voltage of 130 mV at 4 mA. The main design consideration is selecting pull-up values that satisfy the receiving logic while maintaining acceptable switching speed.
추천
Low-Level Sensing
The LM239DG is suitable for low-level sensing when the signal source is sensitive to input bias current. Its 25 nA typical input bias current, +/-5 nA typical input offset current, and 1.3 mV maximum input offset voltage support decisions close to the reference voltage without adding substantial load to the sensor. The four channels allow multiple thresholds to be monitored in one package. Use low-leakage pull-up resistors where slow transitions could be caused by board contamination, and confirm the common-mode limits of every input during startup and fault conditions.
추천
Memory Threshold Monitoring
The LM239DG supports memory and logic threshold monitoring because four comparator channels can detect separate voltage thresholds on data, address, or control signals. The 3 V minimum supply permits operation from common 5 V rails, while the 36 V maximum rating provides additional headroom for industrial systems. Its open-collector outputs can drive wired logic with suitable pull-ups, and the 130 mV typical saturation voltage at 4 mA provides a defined low output level. Designers should verify signal levels, input common-mode range, and power-sequencing behavior before connecting the device to powered memory circuits.
추천
Automotive Interface Circuits
The LM239DG can support interface and protection functions in automotive-style circuits that compare sensed voltages against fixed or adjustable thresholds. Its single-supply range of 3 V to 36 V covers many 12 V-system signal-conditioning needs, while four channels consolidate multiple comparisons into one 14-pin SOIC package. The device's -25 C to +85 C listed temperature range should be checked against the vehicle's environmental requirements. For new safety-related automotive programs, use a part with the required automotive qualification rather than relying on a general-purpose legacy comparator.
추천
Consumer Equipment Thresholding
The LM239DG is appropriate for consumer-equipment thresholding when several analog signals must be converted into digital decisions. Four general-purpose comparators provide independent level checks in a compact 14-pin SOIC package, and the open-collector outputs allow the logic threshold to be established through pull-up resistors. The device can operate from 5 V and 12 V supplies, with a 36 V maximum rating that adds design margin for selected rails. Design the pull-up network for the actual logic family and pay attention to open-collector rise time, particularly when switching repeated signals at high frequency.
추천
Sensor Signal Conditioning
The LM239DG can condition signals from resistive, capacitive, or bridge-based sensors by comparing the sensed voltage with a reference. Its low 25 nA typical input bias current reduces loading on high-impedance sensors, while the 1.3 mV maximum input offset voltage defines an important threshold-error boundary. The four-channel arrangement supports multiple sensor nodes or a combination of sensor and warning thresholds. Keep sensitive input traces short and isolated from switching nodes, and account for input offset, reference tolerance, temperature drift, and comparator hysteresis during precision measurements.
추천
추천 제품 요약
엔지니어링 참조 데이터: LM239DG — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | LM239DR | LM239DR2G | LM239DT | LM339DR |
|---|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | onsemi | Texas Instruments |
| Package | 14-SOIC | 14-SOIC - same footprint | 14-SOIC - same footprint | 14-SOIC - same footprint | 14-SOIC - same footprint |
| Comparator Count | 4 | 4 | 4 | 4 | 4 |
주요 차별점
- Direct onsemi replacement path within the same SOIC footprint (vs LM239DR)
- Four-channel integration reduces component count (vs LM339DR)
- Low input bias supports higher-impedance sensing (vs LM239DT)
설계 노트
Treat every open-collector output as requiring an external pull-up resistor. The LM239DG can sink current to a listed 130 mV typical saturation voltage at 4 mA, but the resistor must still satisfy the input's high-level voltage and leakage requirements. Avoid allowing the output node to float. Also verify that all input and output voltages remain within their absolute-maximum limits during power-up and power-down, especially in circuits where a 36 V rail can remain present while the comparator supply is off.
Route the four comparator input pairs away from switching nodes, relay contacts, inductors, and high-current return paths. Keep the common ground connection short and use a stable ground reference because the comparator evaluates small voltage differences. If the sensed source is high impedance, minimize leakage from board contamination and choose the external reference network accordingly. Place any input filtering capacitors where they will not slow the intended comparison or create unwanted delay when the input crosses the threshold.
The 1.3 mV maximum input offset voltage, 25 nA typical input bias current, and +/-5 nA typical input offset current are central to threshold accuracy. Include comparator offset, reference tolerance, resistor tolerance, temperature drift, and any intentional hysteresis in the system error budget. For slowly changing signals, add positive feedback for hysteresis to prevent output chatter. The open-collector rise time is controlled by the pull-up resistance and total node capacitance, so select a value that balances noise immunity against required switching speed.
Before starting a new design, obtain a lifecycle statement for LM239DG and compare the active LM239DR ordering option. The shared 14-pin SOIC footprint supports PCB reuse, but suffix-specific temperature, packaging, qualification, and orderable attributes must be confirmed. Do not infer automotive qualification or full RoHS or REACH coverage from the family name. For obsolete assemblies, record the last-time-buy opportunity, remaining lot traceability, and date-code requirements before requesting any remaining supply.
규정 준수 정보
The LM239DG is listed for consumer, automotive, and industrial applications, but no specific AEC-Q100 qualification or RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified for the exact ordering code.