LM2902AQT14-13 - 36V Quad Op Amp | Diodes Incorporated
부품 번호: LM2902AQT14-13 ✓ 활성LM2902AQT14-13 개요
An operational amplifier, or op amp, is a high-gain differential amplifier that uses external feedback to set its gain. A quad op amp combines four amplifiers in one package, allowing designers to implement four independent analog signal-conditioning channels while reducing board area. Within the broader semiconductor hierarchy, the LM2902AQT14-13 belongs to the linear amplifier and analog signal-conditioning IC category.
The automotive-qualified LM2902A variant provides a typical input offset voltage of 1 mV, compared with 2 mV for the non-A LM2902 version. Its wide supply range covers 12 V and 24 V automotive rails, while its common-mode input and output capabilities suit sensor buffering, actuator interfaces, and low-frequency control loops. Low input bias current of 20 nA helps preserve accuracy when driving high-impedance sensors.
The internal architecture is internally compensated for stable unity-gain operation, allowing each channel to operate as a voltage follower, inverting amplifier, non-inverting amplifier, comparator, or differential input stage. With 700 kHz bandwidth and 0.3 V/us slew rate, the device handles general-purpose analog signals rather than demanding high-speed precision applications.
Typical uses include battery-management-system sensor interfaces, automotive body and chassis control, industrial transducers, instrumentation amplifiers, active filters, and 4-to-20 mA current-loop receivers. The 14-TSSOP package also makes the quad amplifier practical for compact control boards where every square millimeter matters.
When laying out the PCB, keep input and feedback traces short, place input-biasing resistors close to the non-inverting inputs, and provide stable bypass capacitance at the supply pins. Verify common-mode headroom at the selected output level and confirm the operating temperature rating against the vehicle or industrial environment before release.
This page consolidates supply-range, bandwidth, offset, automotive-qualification, pinout, and drop-in replacement information, and adds application-specific design guidance that helps shorten component selection and board-layout decisions.
드롭인 대체품: LM2902AQT14-13 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
LM2902QT14-13
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →LM2902AQT14
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
LM2902QT14
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
LM2902AQT13-13
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
LM2902AQT14-13 최대 정격 & 전기적 특성
| Amplifier Type | Quad general-purpose operational amplifier |
| Number of Channels | 4 channels |
| Single-Supply Voltage Range | 3 V to 36 V |
| Dual-Supply Voltage Range | +/-1.5 V to +/-18 V |
| 공급 전류 | 700 uA typical for LM2902Q |
| Input Bias Current | 20 nA typical |
| Input Offset Voltage | 1 mV typical for A versions |
| Large DC Voltage Gain | 100 dB |
| Unity-Gain Bandwidth | 700 kHz |
| Slew Rate | 0.3 V/us |
| Automotive Qualification | AEC-Q100 qualified |
| 동작 온도 범위 | -40C to +125C |
| 패키지 | 14-pin TSSOP |
| 실장 유형 | Surface mount |
| Mold Compound | Green mold compound |
| Pinout | Industry-standard quad operational amplifier pinout |
| RoHS 상태 | Compliant |
LM2902AQT14-13 핀 구성
| 핀 1 | OUT1 — Amplifier 1 output |
| 핀 2 | IN1- — Amplifier 1 inverting input |
| 핀 3 | IN1+ — Amplifier 1 non-inverting input |
| 핀 4 | V+ — Positive supply voltage |
| 핀 5 | IN2+ — Amplifier 2 non-inverting input |
| 핀 6 | IN2- — Amplifier 2 inverting input |
| 핀 7 | OUT2 — Amplifier 2 output |
| 핀 8 | OUT3 — Amplifier 3 output |
| 핀 9 | IN3- — Amplifier 3 inverting input |
| 핀 10 | IN3+ — Amplifier 3 non-inverting input |
| 핀 11 | V- — Negative supply voltage |
| 핀 12 | IN4+ — Amplifier 4 non-inverting input |
| 핀 13 | IN4- — Amplifier 4 inverting input |
| 핀 14 | OUT4 — Amplifier 4 output |
일반적인 애플리케이션
LM2902AQT14-13 적합 용도: 6 애플리케이션s: Automotive Sensor Interface Conditioning, Battery Management System Front End, Industrial Transducer Signal Conditioning, Active Filtering and Audio Control, 4-to-20 mA Current Loop Receiver, Compact Multi-Channel Control Board.
Automotive Sensor Interface Conditioning
The LM2902AQT14-13 fits 12 V and 24 V automotive sensor-conditioning inputs because its 3 V to 36 V supply rating removes the need for an additional front-end regulator. Four independently usable channels can buffer pressure, temperature, position, and current-sensor nodes. With 20 nA typical input bias current, high-impedance dividers experience less loading, while 1 mV typical offset keeps small sensor outputs accurately centered. The AEC-Q100 qualification and -40C to +125C operating range support harsh vehicle environments, provided each input remains inside the published common-mode window.
추천
Battery Management System Front End
The LM2902AQT14-13 is useful in battery-management systems that monitor multiple cell or pack voltages. Its four channels can condition high-impedance divider outputs, with 20 nA typical input bias current limiting divider error and 700 kHz unity-gain bandwidth supporting practical low-frequency filtering. Operation directly from a 24 V pack rail simplifies the analog section, while the -40C to +125C rating covers automotive thermal extremes. Designers should still verify the maximum pack voltage, common-mode limits, and output swing during transient and fault conditions.
추천
Industrial Transducer Signal Conditioning
The LM2902AQT14-13 supports industrial pressure, strain, level, and position transducer interfaces that require more supply headroom than a conventional 5 V amplifier. The wide 3 V to 36 V input range allows the amplifier to operate near the top of a 24 V control supply when the signal common-mode range permits. Its 1 mV typical offset and 20 nA typical input bias current help preserve low-level measurement accuracy, while four channels in one 14-TSSOP reduce board area. Feedback-network values should be calculated for the chosen gain and noise bandwidth.
추천
Active Filtering and Audio Control
The LM2902AQT14-13 can implement active filters, volume-control paths, and general audio-frequency control circuits because each channel provides 700 kHz unity-gain bandwidth and 0.3 V/us slew rate. Its 100 dB large-signal DC gain supports accurate closed-loop gain setting, and the internally compensated architecture allows straightforward unity-gain buffer use. The wide supply range also helps when an analog stage must share a 12 V or 24 V rail. Keep the closed-loop bandwidth well below the unity-gain value and verify output swing at the required signal level.
추천
4-to-20 mA Current Loop Receiver
The LM2902AQT14-13 is suitable for receiving the voltage produced by a 4-to-20 mA current-loop transmitter, especially in industrial equipment operating from a 24 V supply. Its 20 nA typical input bias current limits loading of the loop, and the high open-loop gain of 100 dB supports accurate differential amplification. The quad package can implement the receiver plus additional low-frequency filtering or channel multiplexing functions. Input protection must account for the maximum loop voltage and surge conditions rather than relying only on the nominal 36 V supply rating.
추천
Compact Multi-Channel Control Board
The LM2902AQT14-13 consolidates four analog channels into a single 14-TSSOP, making it practical for compact control boards that must amplify several low-frequency signals. Each channel can independently serve as a follower, inverting or non-inverting stage, active filter, or comparator. The 700 kHz unity-gain bandwidth is sufficient for many control and instrumentation signals, and the 36 V maximum supply expands the working rail range. Place bypass capacitors near the supply pins, route feedback loops compactly, and test each channel independently during board bring-up.
추천
추천 제품 요약
엔지니어링 참조 데이터: LM2902AQT14-13 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | LM2902QT14-13 | LM2902AQT14 | LM2902QT14 | LM2902AQT13-13 |
|---|---|---|---|---|---|
| Brand | Diodes Incorporated | Diodes Incorporated | Diodes Incorporated | Diodes Incorporated | Diodes Incorporated |
| Package | TSSOP-14 | TSSOP-14 - same footprint | TSSOP-14 - same footprint | TSSOP-14 - same footprint | TSSOP-14 - same footprint |
| Amplifier Channels | 4 | 4 | 4 | 4 | 4 |
| Single-Supply Voltage Range | 3 V to 36 V | 3 V to 36 V | 3 V to 36 V | 3 V to 36 V | 3 V to 36 V |
| Dual-Supply Voltage Range | +/-1.5 V to +/-18 V | +/-1.5 V to +/-18 V | +/-1.5 V to +/-18 V | +/-1.5 V to +/-18 V | +/-1.5 V to +/-18 V |
| Input Offset Voltage | 1 mV typical for A version | 2 mV typical for non-A version | 1 mV typical for A version | 2 mV typical for non-A version | 1 mV typical for A version |
| Input Bias Current | 20 nA typical | 20 nA typical | 20 nA typical | 20 nA typical | 20 nA typical |
| Unity-Gain Bandwidth | 700 kHz | 700 kHz | 700 kHz | 700 kHz | 700 kHz |
| Slew Rate | 0.3 V/us | 0.3 V/us | 0.3 V/us | 0.3 V/us | 0.3 V/us |
| Supply Current | 700 uA typical | 700 uA typical | 700 uA typical | 700 uA typical | 700 uA typical |
주요 차별점
- Lower typical input offset within the automotive LM2902A grade (vs LM2902QT14-13)
- Automotive temperature and qualification positioning (vs LM2902QT14-13)
- Wide supply tolerance with four integrated channels (vs LM2902AQT14)
- Wide supply tolerance with four integrated channels (vs LM2902QT14)
설계 노트
The 3 V to 36 V supply capability simplifies 12 V and 24 V analog designs, but the supply pins still require local bypass capacitance and careful return-current planning. Place a high-frequency ceramic capacitor and a bulk capacitor near pins 4 and 11, keep supply traces short, and route the return directly to the device ground or supply-reference point. On single-supply systems, treat the V- pin as the signal-reference node rather than assuming a negative rail is required.
Keep each op-amp's feedback components, input source, and output load close to the associated package pins. Resistors larger than a few hundred ohms can amplify thermal noise and leakage, so use practical values while maintaining stable closed-loop gain. Do not run input and output traces in parallel where capacitive coupling could create feedback. Since the TSSOP leads are closely spaced, verify mask clearance, solder-paste volume, and reflow profile for fine-pitch assembly.
The wide supply rating does not make the LM2902AQT14-13 rail-to-rail. Check the datasheet's input common-mode range and output swing against the actual signal, especially on 3 V or 5 V supplies. Also distinguish the A version's 1 mV typical offset from the non-A version's 2 mV typical offset. Input protection must be sized for external transients, because the 36 V maximum supply rating is not a substitute for a dedicated clamp network.
규정 준수 정보
The device is identified as automotive compliant and AEC-Q100 qualified. The manufacturer documents use of green mold compound. Reach, lead-free status, halogen-free status, and conflict-minerals status are not stated in the product information and remain unconfirmed.