LM2902KAVQDRG4 - 30V Quad Op Amp | Texas Instruments
부품 번호: LM2902KAVQDRG4 ✓ 활성LM2902KAVQDRG4 개요
An operational amplifier is a high-gain analog building block that compares its inverting and non-inverting inputs and drives its output toward the voltage required to reduce the difference between them. The LM2902 belongs to the operational-amplifier hierarchy within amplifier ICs, analog signal-processing ICs, and semiconductor components. Its four independent channels allow multiple analog functions to be implemented in one package, reducing board area and simplifying component inventory.
Key characteristics include a 1.2 MHz gain-bandwidth product for moderate-frequency signal processing, a 0.5 V/µs slew rate for changing output waveforms, and a 2 mV input offset voltage. The manufacturer identifies the automotive-qualified LM2902KAV family with improved ESD protection of 2 kV. These characteristics make the amplifier suitable for industrial controls, automotive electronics, sensor interfaces, power-supply control loops, and general-purpose analog signal conditioning.
The four amplifiers are frequency compensated and intended for operation from a single supply or split supplies. This allows the same device to process signals referenced to ground or signals centered around a midpoint created by two supply rails. Independent channels can perform amplification, filtering, comparisons, level shifting, current-voltage conversion, or feedback functions without coupling between the amplifiers, provided each channel respects the common supply and grounding limits.
Typical applications include conditioning resistive sensor signals, buffering outputs from transducers, amplifying low-frequency control signals, supporting feedback networks in power converters, driving analog inputs in industrial equipment, and implementing multiple amplifier channels in automotive electronic modules. The 30 V supply capability provides useful headroom for industrial and automotive environments, while the 14-pin SOIC package supports conventional surface-mount assembly and inspection.
When laying out a circuit, keep each input and feedback path short, connect bypassing capacitors close to the supply pins, and route return currents without sharing narrow paths with sensitive signals. Confirm output swing, input common-mode range, stability, and thermal conditions for the intended supply voltage before using the device in a new design. The manufacturer datasheet remains the controlling reference for limits and test conditions.
This product page combines the exact ordering information, key electrical characteristics, package details, application guidance, design notes, and qualified drop-in alternatives for LM2902KAVQDRG4. It also distinguishes automotive-qualified choices from electrically similar family members so engineers can make a replacement decision without treating every similar quad amplifier as automatically interchangeable.
드롭인 대체품: LM2902KAVQDRG4 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: LM2902KAVQDRG4 (동일 폼 팩터 및 풋프린트) — 차이점: Amplifier Type, Number of Amplifier Channels.
LM2902KVQDRQ1
✅ 드롭인가격 문의
데이터시트 보기 →LM2902DR
✅ 드롭인 ⚠️ 사양 미검증가격 문의
데이터시트 보기 →LM2902KAVQDRG4 최대 정격 & 전기적 특성
| Number of Amplifier Channels | 4 channels |
| Supply Voltage Range | 3 V to 30 V |
| Gain-Bandwidth Product | 1.2 MHz |
| Input Offset Voltage | 2 mV |
| Slew Rate | 0.5 V/µs |
| Improved ESD Protection | 2 kV |
| Automotive Qualification | AEC-Q100 qualified |
| 패키지 | 14-SOIC |
| 핀 수 | 14 pins |
| 실장 유형 | Surface mount |
| Amplifier Type | General-purpose operational amplifier |
| Number of Independent Channels | 4 independent channels |
| Compensation | Internally compensated |
| Supply Configuration | Single supply or split supply |
LM2902KAVQDRG4 핀 구성
| 핀 1 | OUT1 — Amplifier 1 output |
| 핀 2 | IN1- — Amplifier 1 inverting input |
| 핀 3 | IN1+ — Amplifier 1 non-inverting input |
| 핀 4 | V- — Negative supply connection |
| 핀 5 | IN2+ — Amplifier 2 non-inverting input |
| 핀 6 | IN2- — Amplifier 2 inverting input |
| 핀 7 | OUT2 — Amplifier 2 output |
| 핀 8 | OUT3 — Amplifier 3 output |
| 핀 9 | IN3- — Amplifier 3 inverting input |
| 핀 10 | IN3+ — Amplifier 3 non-inverting input |
| 핀 11 | V+ — Positive supply connection |
| 핀 12 | IN4- — Amplifier 4 inverting input |
| 핀 13 | IN4+ — Amplifier 4 non-inverting input |
| 핀 14 | OUT4 — Amplifier 4 output |
일반적인 애플리케이션
LM2902KAVQDRG4 적합 용도: 6 애플리케이션s: Automotive Sensor Conditioning, Industrial Control Signal Conditioning, Power-Supply Feedback Control, Data Acquisition and Buffering, Audio and Communication Interface Buffers, Embedded Control Analog Front Ends.
Automotive Sensor Conditioning
The LM2902KAVQDRG4 fits automotive sensor interfaces that require several low-frequency analog channels on one board. Its four independent amplifiers can buffer resistive sensors, amplify strain-gauge or position-sensor outputs, and provide active filtering without adding separate amplifier packages. The 3 V to 30 V operating range provides useful supply flexibility, while 2 kV improved ESD protection and AEC-Q100 qualification strengthen its suitability for qualified automotive electronics. The 1.2 MHz gain-bandwidth product handles general-purpose control signals rather than high-frequency waveform tasks, and the 2 mV input offset should be included in the worst-case error budget for precision sensing.
추천
Industrial Control Signal Conditioning
The LM2902KAVQDRG4 is appropriate for industrial control modules that combine sensor acquisition, reference buffering, and error-amplifier functions. Its four independent channels reduce component count while supporting a 3 V to 30 V supply range for common industrial rails. A 1.2 MHz gain-bandwidth product supports low-bandwidth process-control signals, and the 0.5 V/µs slew rate provides adequate response for gradual setpoint changes. The 2 mV offset becomes important when the amplifier performs the final stage of high-gain sensing, so designers should include it in the system error budget and verify common-mode behavior near the selected supply rails.
추천
Power-Supply Feedback Control
The LM2902KAVQDRG4 can implement error amplifiers, current-sense amplifiers, and feedback paths in loosely regulated linear or switching power systems. Its 30 V maximum supply is useful for higher-voltage industrial power stages, while the 0.5 V/µs slew rate allows the output to respond to loop compensation transients. Four independent channels can also support auxiliary pre regulation, current monitoring, and output buffering. Because compensation and stability depend on the power-stage topology, capacitor values, load, and ESR, use the manufacturer application guidance and verify the complete loop rather than treating the amplifier as a standalone block.
추천
Data Acquisition and Buffering
The LM2902KAVQDRG4 can buffer inputs to analog-to-digital converters or multiplexers in moderate-speed measurement systems. Its four channels allow simultaneous or sequential conditioning of several sensor outputs, and the 1.2 MHz gain-bandwidth product supports signals well beyond conventional DC-only instrumentation. The 2 mV input offset is significant when the acquisition chain requires high DC accuracy, while the 0.5 V/µs slew rate helps preserve large-signal steps into capacitive sampling inputs. Use the amplifier primarily for low-to-moderate bandwidth signals, and verify settling behavior, output drive, and noise against the converter requirements.
추천
Audio and Communication Interface Buffers
The LM2902KAVQDRG4 can provide impedance buffering and modest gain stages for low-frequency communication or audio interface circuits. Its 1.2 MHz bandwidth and 0.5 V/µs slew rate are suitable for general-purpose tone and control paths, while the quad configuration allows separate handling of microphone-level, line-level, and auxiliary signals. The device is not positioned as a high-performance low-noise audio amplifier, so the 2 mV offset and other noise-related limits must be checked against the signal chain. For demanding audio applications, use the manufacturer datasheet to determine whether the selected LM2902KAV configuration meets the required noise, distortion, and frequency-response targets.
추천
Embedded Control Analog Front Ends
The LM2902KAVQDRG4 can provide four analog channels around an embedded controller for actuator feedback, analog monitoring, and signal conditioning. Its 2 mV input offset supports general-purpose monitoring rather than precision metrology, and the 1.2 MHz bandwidth accommodates common embedded-control bandwidths. The 3 V lower supply limit permits use with 3.3 V systems, while operation up to 30 V covers higher-voltage interfaces when the connected signals remain within the input common-mode range. Designers should use separate, well-planned grounding, place bypass capacitance near the device, and isolate analog paths from switching nodes to avoid converting digital activity into coupled amplifier errors.
추천
추천 제품 요약
엔지니어링 참조 데이터: LM2902KAVQDRG4 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | LM2902KVQDR | LM2902DR |
|---|---|---|---|
| Package | 14-SOIC | 14-SOIC | 14-SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Channels | 4 independent channels | 4 independent channels | 4 independent channels |
| Gain-Bandwidth Product | 1.2 MHz | 1.2 MHz | 1.2 MHz |
| Input Offset Voltage | 2 mV | 2 mV | 2 mV |
주요 차별점
- Improved ESD protection within the LM2902KAV family (vs LM2902DR)
- Automotive-qualified family configuration (vs LM2902DR)
- Wide supply operation in a compact quad package (vs LM2902KVQDR)
설계 노트
Place the input, feedback, and bypass components close to their associated LM2902KAVQDRG4 pins. Keep each amplifier channel's non-inverting and inverting routes short, and connect the bypass capacitor directly between the supply pins and ground rather than routing it around the board. In split-supply systems, provide adequate bypassing for both rails because negative supply transients can disturb otherwise correct operation.
Do not select the amplifier only from its 30 V supply rating. Check that every input remains within the common-mode range, that the required output swing is achievable at the chosen load, and that the selected gain is stable with the feedback network. The 2 mV input offset can dominate a high-gain sensor path, while the 1.2 MHz bandwidth limits closed-loop response at high frequencies.
Separate sensitive amplifier inputs from high-current switching nodes and high-impedance bias paths. Use a compact ground-return arrangement around each amplifier, avoid sharing narrow return paths between analog channels and digital loads, and place any protection or filtering components where they do not add unnecessary loop area. These practices reduce coupling of switching energy and ground movement into the input offset and output of the amplifier.
규정 준수 정보
The LM2902KAV family is identified as AEC-Q100 qualified for automotive applications. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer or supply-chain documentation.