LM2904YST - Dual Low-Power Op Amp, 8-MiniSO | STMicroelectronics
부품 번호: LM2904YST ✓ 활성LM2904YST 개요
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM2904 contains two such amplifier sections, allowing one package to process two related signals or to implement two stages of a larger circuit. As a bipolar operational amplifier, it provides input bias-current behavior and voltage-noise characteristics suited to many low-cost precision and control applications rather than the very low input bias current associated with CMOS or JFET input devices.
The LM2904YST supports operation across a wide supply range and can operate with dual supplies such as ±15 V. The 30 V maximum supply rating provides useful headroom for industrial applications, while the low-power operating-current target reduces heat generation in battery- and line-powered equipment. Each channel uses a differential input arrangement and provides a single-ended output referenced to the negative supply rail. Common applications include buffering sensors, amplifying low-level control signals, and driving external circuitry within the amplifier’s output-current capability.
The 8-MiniSO package is a compact surface-mount form factor that reduces board space compared with traditional through-hole SOIC packages. The YST ordering suffix identifies the tape-and-reel presentation, allowing the amplifier to be assembled through standard surface-mount production processes. Because operational-amplifier performance depends on surrounding passives and layout, input and feedback components should be positioned close to the relevant pins, while adequate supply bypassing should be placed directly across the device’s supply terminals.
LM2904YST is appropriate for industrial instrumentation, feedback-control loops, transducer amplification, audio preamplification, and low-frequency analog filters. The dual-channel arrangement can reduce component count in designs using two separate gain stages. In designs requiring input offset current below the LM2904’s range, rail-to-rail precision, or operation from a single low-voltage supply, a CMOS-input amplifier may offer a better technical match even if it shares a similar package.
Designers should verify input and output voltage limits at the selected supply voltage, confirm the required gain bandwidth and slew rate, and check that the planned load does not exceed the output-current capability. Input common-mode range, output swing, electrical-noise limits, and thermal performance should be checked against the worst-case operating conditions. Decoupling capacitors should be selected according to the manufacturer’s recommended application circuit and stability requirements.
This product overview combines the manufacturer-distinguished LM2904YST configuration with package, application, cross-reference, and design-placement guidance. It supports faster component identification while emphasizing the distinctions engineers must validate before approving any analog signal-chain design.
드롭인 대체품: LM2904YST — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: LM2904YST (동일 폼 팩터 및 풋프린트) — 차이점: Package, Number of Channels, Amplifier Type, Input Offset Voltage, Mounting Type.
LM2904ST
✅ 드롭인가격 문의
데이터시트 보기 →LM2904DR
✅ 드롭인가격 문의
데이터시트 보기 →LM2904BIDR
✅ 드롭인가격 문의
데이터시트 보기 →LM2904LVQDGKRQ1
✅ 드롭인가격 문의
데이터시트 보기 →LM2904YST 최대 정격 & 전기적 특성
| Product Type | Dual operational amplifier |
| Amplifier Count | 2 channels |
| 출력 유형 | Single-ended output per channel |
| Maximum Supply Voltage | 30 V |
| Nominal Dual-Supply Example | ±15 V |
| Automotive Qualification | AEC-Q100 |
| 패키지 | 8-MiniSO |
| 실장 유형 | Surface mount |
| Packaging | Tape and reel |
LM2904YST 핀 구성
| 핀 1 | OUT1 — Amplifier 1 output |
| 핀 2 | IN1- — Amplifier 1 inverting input |
| 핀 3 | IN1+ — Amplifier 1 non-inverting input |
| 핀 4 | V- — Negative supply connection |
| 핀 5 | IN2+ — Amplifier 2 non-inverting input |
| 핀 6 | IN2- — Amplifier 2 inverting input |
| 핀 7 | OUT2 — Amplifier 2 output |
| 핀 8 | V+ — Positive supply connection |
일반적인 애플리케이션
LM2904YST 적합 용도: 6 애플리케이션s: Industrial Sensor Signal Conditioning, Audio Preamplifier Stages, Automotive Control and Interface Circuits, Power-Supply Feedback Control, Low-Frequency Active Filters, Data Acquisition and Instrumentation.
Industrial Sensor Signal Conditioning
The LM2904YST is well suited to conditioning low-level signals from industrial sensors because its dual-amplifier architecture provides two independent stages in one 8-MiniSO package. One channel can amplify or buffer the sensor output while the other can perform filtering, level shifting, or an additional gain stage. The device supports a maximum supply rating of 30 V, which helps accommodate 24 V industrial systems when the input and output limits are observed. Engineers should still verify input bias current, common-mode range, offset voltage, gain-bandwidth product, and output swing against the sensor characteristics. Stable feedback networks and short input traces are important because the operational amplifier’s practical accuracy depends on component tolerances and PCB parasitics.
추천
Audio Preamplifier Stages
The LM2904YST can implement two low-frequency audio preamplifier stages when the design accepts bipolar-input noise and offset characteristics. Its two single-ended amplifier channels support gain, inversion, active filtering, and output buffering without requiring two packages. This is useful in line-level or instrument-amplifier-style circuits where the 30 V maximum supply rating provides operating headroom above lower-voltage analog rails. The designer should confirm gain-bandwidth product and slew-rate requirements for the highest intended audio frequency and verify that the output swing remains within limits at the selected load. Power-supply bypass capacitors should be placed close to the supply pins to prevent amplified supply noise from appearing at the output.
추천
Automotive Control and Interface Circuits
The LM2904YST is identified as an AEC-Q100 automotive-grade dual operational amplifier, making it a candidate for low-frequency control, buffering, and general interface circuits in automotive electronics. The 8-MiniSO package supports compact surface-mount assemblies, while the 30 V supply rating can suit systems operating below that maximum. Automotive selection still requires careful validation of temperature limits, transient behavior, input common-mode range, output swing, noise, and system electromagnetic compatibility. The amplifier should not be placed directly beside high-switching-current drivers without appropriate grounding and filtering. Review the manufacturer application information and conduct board-level testing across voltage, temperature, load, and automotive transient conditions before production release.
추천
Power-Supply Feedback Control
The LM2904YST can be used in voltage-feedback control loops where its two amplifier channels provide error amplification and output buffering. The dual topology reduces component count in designs that compare an output voltage against a reference and drive a control or feedback stage. The broad 30 V maximum supply rating is useful for industrial power systems, although the exact minimum operating voltage and input common-mode range must be checked against the reference and feedback-node voltages. Designers should evaluate offset voltage, input bias current, open-loop gain, output-current capability, and stability with the selected compensation network. Keep the feedback loop compact and place the reference and compensation components close to the relevant amplifier pins.
추천
Low-Frequency Active Filters
The LM2904YST is applicable to low-frequency active-filter stages where two amplifier channels can form a second-order section or implement cascaded first-order filtering. Its dual package allows filter and buffer functions to be combined in a compact 8-MiniSO footprint. The design must remain within the amplifier’s gain-bandwidth and slew-rate capabilities while also accounting for input bias current, output swing, and load drive. Use stable resistor and capacitor arrangements, keep sensitive input nodes short, and place supply bypass capacitance near pins 4 and 8. If the filter must accept very high-impedance sensors, compare the LM2904’s bias-current behavior with a FET- or CMOS-input amplifier before finalizing the source impedance.
추천
Data Acquisition and Instrumentation
The LM2904YST is appropriate for instrumentation buffers and low-level analog processing where two channels can be used for sequential or differential stages. The 30 V-rated device is useful in higher-voltage laboratory and industrial systems, while its compact 8-MiniSO package helps reduce board area. Instrumentation performance should be assessed using offset voltage, input bias current, voltage noise, common-mode rejection, and output-drive requirements rather than the amplifier category alone. Place input and feedback resistors near the relevant pins, maintain symmetrical routing where channel matching matters, and decouple the supply rails close to the device. A rail-to-rail or precision CMOS-input amplifier may be preferable for low-voltage acquisition systems whose signals approach either supply rail.
추천
추천 제품 요약
엔지니어링 참조 데이터: LM2904YST — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | LM2904ST | LM2904 | LM2904B | LM2904LV | LM2904PWR |
|---|---|---|---|---|---|---|
| Package | 8-MiniSO | 8-MiniSO | 8-MiniSO | 8-MiniSO | 8-MiniSO | TSSOP-8 |
| Brand | STMicroelectronics | STMicroelectronics | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Count | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Special Features | Automotive-grade dual low-power amplifier | LM2904-family dual amplifier | Dual general-purpose operational amplifier | Pin-to-pin upgrade with upgraded functionality | LM2904-family low-voltage option | LM2904-family dual amplifier |
주요 차별점
- Higher listed maximum supply rating (vs Texas Instruments LM2904)
- Automotive-grade configuration (vs Texas Instruments LM2904B)
- Same-manufacturer family option (vs LM2904ST)
- Dual-channel functional integration (vs Single-amplifier alternatives)
설계 노트
Place each amplifier’s feedback resistors and input components close to the associated package pins, and route sensitive input traces away from power-switching nodes. Supply bypass capacitors should connect directly between pins 8 and 4 with a short ground return. Although the LM2904YST has two channels in one package, maintain symmetrical channel layouts when offset or gain matching matters.
Use the 30 V value only as the maximum supply rating, not as an indication that every input and output voltage remains valid at that rail. Check the complete input common-mode and output-swing limits from the manufacturer datasheet for the selected supply. Also verify the operating-current and output-current limits against the load, because these parameters determine whether an external buffer is required.
Do not select LM2904YST solely because its supply rating is higher than that of a competing family member. A valid drop-in decision requires the same 8-MiniSO footprint, identical amplifier-channel pin assignment, acceptable common-mode range, output swing, gain-bandwidth product, and qualification. LM2904PWR uses TSSOP-8 and therefore requires a different PCB footprint despite sharing the general LM2904 function.
Use the smallest practical loop area around each op-amp input and feedback loop. Long traces can add parasitic capacitance that alters high-frequency behavior, while common-impedance inductance in the supply connection can couple switching noise into the output. Confirm stability with the intended gain, source impedance, load capacitance, and supply-bypass network before production release.
규정 준수 정보
The LM2904YST is identified as AEC-Q100 automotive-grade. Other environmental and material compliance attributes were not confirmed for the exact ordering code.