LM324ANG - 4-Channel 3-32V Op Amp | onsemi | Through-Hole
부품 번호: LM324ANG ✓ 활성LM324ANG 개요
An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. The LM324 series belongs to the quad operational-amplifier family within the broader linear amplifier and signal-conditioning hierarchy. Its differential input architecture is useful for comparing a sensor signal with a reference voltage, amplifying small signals in control systems, buffering high-impedance sources, and implementing basic active filters or summing circuits.
The LM324ANG combines four amplifiers, single-supply operation from 3 V to 32 V, a 1 MHz gain-bandwidth product, and a 65 dB minimum common-mode rejection ratio. These characteristics make it suitable for industrial control, instrumentation, sensor interfaces, audio and communications support circuits, and general embedded-system analog conditioning. The input offset voltage of 3 mV is important in precision-sensitive applications and should be considered when defining acceptable error budgets.
The device is intended for general-purpose, non-quadrature applications where economical integration and simple single-supply operation are more important than low-noise, high-speed, or rail-to-rail performance. Its four internal channels share the device power rails but provide independent differential inputs and outputs. Engineers should design feedback networks around the required closed-loop gain and check output swing, input common-mode range, output-current capability, and stability at the selected operating voltage.
Typical circuit roles include amplifying a 0-5 V sensor signal, buffering a potentiometer, comparing a control signal with a reference, driving the input stage of a power circuit, and providing four independent amplifier channels in one package. The 14-pin PDIP package is suited to through-hole PCB assembly, educational prototypes, industrial control boards, and repair or modernization work where a pin-compatible replacement is needed.
When laying out a board, place input, feedback, and decoupling connections close to the device, connect the power pins to a low-impedance ground plane, and decouple the supply near the package. Avoid long high-impedance input traces because leakage and board contamination can increase offset error. Review the manufacturer datasheet for the exact pin assignment, input common-mode limits, output swing, supply-current behavior, and recommended compensation values.
This page combines the LM324ANG’s core electrical and package characteristics with application guidance, design notes, and practical drop-in alternatives. It is intended to help engineers select the part quickly, compare equivalent quad op amps, and plan a PCB or replacement strategy without overlooking the limitations of a general-purpose operational amplifier.
드롭인 대체품: LM324ANG — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: LM324ANG (동일 폼 팩터 및 풋프린트) — 차이점: Mounting Type, Package, Amplifier Type, Frequency Compensation, Gain-Bandwidth Product.
LM324N
✅ 드롭인가격 문의
데이터시트 보기 →LM324ADR2G
✅ 드롭인가격 문의
데이터시트 보기 →TL074CDR
✅ 드롭인가격 문의
데이터시트 보기 →LMC662
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
LM324ANG 최대 정격 & 전기적 특성
| Number of Channels | 4 channels |
| Device Type | Quad operational amplifier |
| Supply Voltage Range | 3 V to 32 V |
| Input Offset Voltage | 3 mV |
| Common-Mode Rejection Ratio | 65 dB minimum |
| Gain-Bandwidth Product | 1 MHz |
| Input Type | True differential inputs |
| Operating Temperature Grade | Commercial temperature grade |
| 패키지 | 14-PDIP |
| 실장 유형 | Through-hole |
| 핀 수 | 14 pins |
LM324ANG 14-pdip 핀 구성 가이드
LM324ANG(14-pdip 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: LM324ANG.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
LM324ANG 적합 용도: 6 애플리케이션s: Industrial Sensor Signal Conditioning, 5 V Control and Interface Circuits, Audio and Communications Support, Instrumentation and Measurement, Power-Supply Control and Feedback, Educational and Prototype Circuits.
Industrial Sensor Signal Conditioning
The LM324ANG is suitable for conditioning 0-5 V or other sensor signals in industrial control boards because it combines four differential-input channels with a 3 V to 32 V single-supply range. It can amplify a low-level sensor output, compare the conditioned signal against a reference, and provide additional buffering for an actuator interface. A 3 mV input offset is a meaningful error term, so precision sensing designs should calculate its effect against the full-scale signal. The 1 MHz gain-bandwidth product is sufficient for many low-frequency control and monitoring loops but should be checked for the selected closed-loop gain. The 14-pin PDIP package also simplifies through-hole industrial control-board assembly and maintenance.
추천
5 V Control and Interface Circuits
The LM324ANG works from a single 5 V rail, making it useful in legacy 5 V embedded and control systems where separate positive and negative amplifier supplies would add cost and complexity. Its four channels can implement independent comparators, transimpedance-style stages, logic-level interface buffers, and feedback networks around other analog blocks. The amplifier does not provide rail-to-rail input or output operation, so the signal amplitude and output target must remain inside the manufacturer’s common-mode and swing limits. The 3 mV input offset specification and 65 dB minimum common-mode rejection ratio should be evaluated for the circuit’s accuracy and noise requirements.
추천
Audio and Communications Support
The LM324ANG can provide inexpensive low-frequency amplification, buffering, mixing, and gain control in general audio or communications support circuits. Its four independent channels allow a board designer to implement several modest-signal functions without using four separate amplifier packages, while the 1 MHz gain-bandwidth product supports applications well below audio-band precision requirements. The device’s true differential inputs are useful when a signal must be compared with or subtracted from a local reference. Designers should avoid interpreting it as a low-noise audio preamplifier: the 3 mV input offset and unspecified low-noise performance may dominate quiet-signal designs, and output swing must remain within the selected supply rails.
추천
Instrumentation and Measurement
The LM324ANG is appropriate for low-frequency instrumentation buffers, comparator stages, and general measurement interfaces where economical quad integration is useful. Its differential inputs allow subtraction and reference comparison, while the 65 dB minimum common-mode rejection ratio helps reject common-mode voltage in sensor and measurement paths. For bridge outputs, low-level thermocouple signals, or precision instrumentation, however, the 3 mV input offset is generally too large unless calibrated or compensated. The 14-pin PDIP format supports through-hole measurement modules and educational equipment where replaceability and straightforward assembly are priorities.
추천
Power-Supply Control and Feedback
The LM324ANG can implement error amplifiers, voltage comparators, and feedback elements in basic linear power-control circuits. Its four channels provide enough independent amplifier stages to combine sensing, error amplification, and auxiliary functions on a through-hole control board. The 3 V to 32 V operating range is useful for higher-voltage industrial systems, although the amplifier is not a dedicated power-controller IC and must be checked for output-current capability and output swing. Because the input and output do not operate fully rail-to-rail, designers should include adequate headroom and verify stability with the selected compensation network.
추천
Educational and Prototype Circuits
The LM324ANG is a practical quad op amp for educational laboratories, breadboard-style prototypes, and through-hole evaluation boards. Four accessible channels make it possible to compare inverting, non-inverting, summing, comparator, and filtering configurations on one 14-pin package. The simple general-purpose architecture is easy to teach and troubleshoot, while the 3 V to 32 V range supports common laboratory supplies. Students and engineers should still observe the input common-mode range, output swing, and recommended feedback values. For new low-voltage designs requiring rail-to-rail performance or micropower operation, a modern amplifier family may provide a more suitable starting point.
추천
추천 제품 요약
엔지니어링 참조 데이터: LM324ANG — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | LM324N | LM324A | TL074 | LMC662 |
|---|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | Texas Instruments | Texas Instruments |
| Package | 14-PDIP | 14-PDIP | 14-PDIP | 14-PDIP | 14-PDIP |
| Number of Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Mounting Type | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
주요 차별점
- Four independent general-purpose channels in one through-hole package (vs LM324N)
- Single-supply operation across a wide voltage range (vs TL074)
- True differential-input general-purpose architecture (vs LMC662)
설계 노트
Place the power-decoupling capacitor immediately beside the LM324ANG supply and ground pins, and route the amplifier inputs and feedback components directly to the package. Keep sensitive input traces short and away from switching nodes and high-current return paths. Because the specified input offset is 3 mV, long PCB leakage paths and contaminated connector inputs can contribute meaningful error in high-impedance sensor circuits.
Do not assume the LM324ANG input and output can swing rail-to-rail. Before connecting a 5 V signal or targeting a 5 V output, check the manufacturer’s input common-mode range and output-swing limits for the selected supply. Also verify the gain-bandwidth product of 1 MHz at the intended closed-loop gain, and use the recommended compensation network where stability could be affected by capacitive loading.
Treat each amplifier channel independently for layout purposes even though all four channels share the same supply pins. Separate high-impedance non-inverting inputs from ground and power-return paths, and avoid routing them beside the differential input of another channel. A 65 dB minimum common-mode rejection ratio helps only when the unwanted signal is genuinely common-mode; it does not correct saturation caused by an input outside the permitted common-mode range.
Calculate amplifier dissipation from the actual supply voltage, output voltage, load current, and quiescent current before assigning copper area or board temperature limits. The LM324ANG can operate from 3 V to 32 V, so the same package can face very different dissipation across industrial and low-voltage systems. Keep the operating junction temperature within the manufacturer limit and avoid placing a high-dropout channel next to heat-sensitive circuitry without thermal review.
규정 준수 정보
The cited product text identifies a commercial-temperature LM324ANG but does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Verify these attributes against the current manufacturer product page and the exact ordering documentation.