Analog Devices

LT1013IS8 - Dual Precision Op Amp, 44V, SOIC-8 | Analog Devices

부품 번호: LT1013IS8 ✓ 활성
5 V to 44 V Vdss 500 uA Id 8-pin SOIC, 8-SO Package 0.55 uV peak-to-peak (0.1 Hz to 10 Hz) Speed
MOQ: 1 |

LT1013IS8 개요

The Analog Devices LT1013IS8 is a dual precision operational amplifier in an 8-pin SOIC package, optimized for low-noise instrumentation and accurate signal conditioning. It operates from a 5 V single supply to a ±15 V split supply, provides a guaranteed minimum open-loop gain of 1.5 million with a 5 mA load and 800,000 with a 17 mA load, and limits supply current to 500 uA maximum. Its specified 0.55 uV peak-to-peak noise over 0.1 Hz to 10 Hz and 0.07 pA/√Hz current noise support precision measurement of weak sensor signals.

An operational amplifier is an active analog signal-conditioning component that amplifies the difference between its inverting and non-inverting inputs. Within the broader hierarchy, the LT1013 belongs to the precision operational amplifier class, then to the voltage-feedback amplifier family, and ultimately to the wider integrated-circuit and signal-chain product categories. Its dual architecture provides two independent amplifiers in one package, making it suitable for instrumentation, filtering, threshold detection, and current-loop interface circuits.

Key characteristics include a 44 V maximum supply voltage, very high open-loop gain, low supply current, and low-noise performance. The 500 uA maximum supply current is especially useful in battery-powered instruments where amplifier power consumption directly affects the available operating interval. The 1.5 million minimum gain at 5 mA supports high-resolution feedback networks, while the 0.07 pA/√Hz current-noise figure is valuable when the input source is a high-impedance transducer rather than a low-resistance voltage source.

The LT1013 operates with both single 5 V and dual ±15 V supplies, allowing the same device to serve portable measurement systems and higher-voltage industrial instrumentation. Its precision characteristics make it appropriate for strain-gauge amplifiers, thermocouple amplifiers, instrumentation-amplifier input stages, and 4 mA-to-20 mA current-loop transmitters. Because the device is not rail-to-rail, output-swing and common-mode headroom must be checked against the selected supply voltage and load.

For reliable layouts, place the feedback resistors close to their associated pins and route input and output traces away from switching nodes and high-current paths. Bypass the supply pins with short ceramic connections, and verify offset, bias current, noise, and settling requirements at the actual signal bandwidth before fixing the gain network.

This page combines device specifications, sourcing information, drop-in ordering-code references, application guidance, and practical design notes. It also provides a parameter-by-parameter comparison to help engineers assess package, supply range, noise, gain, and supply-current differences before making a board-level substitution.

드롭인 대체품: LT1013IS8 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

이 시리즈의 변형

다음과 드롭인 호환되는 동일 시리즈 모델: LT1013IS8 (동일 폼 팩터 및 풋프린트) — 차이점: RoHS Status, Supply Voltage Range.

Texas Instruments
RoHS Status: unknown
Supply Voltage Range: 4 V to 44 V
비교 대상: LT1013IS8 →

LT1013IS8#PBF

✅ 드롭인
📦 8-pin SOIC
Lead-free ordering suffix with the same 8-pin SOIC pin arrangement; electrical performance is unchanged

📋 참조 대체품 (카탈로그에 없음)

LT1013IS8#TR

✅ 드롭인
📦 8-pin SOIC
Tape-and-reel ordering code with identical electrical ratings and 8-pin SOIC footprint

📋 참조 대체품 (카탈로그에 없음)

LT1013CN8

✅ 드롭인 ⚠️ 사양 미검증
📦 8-pin SOIC
Same LT1013 dual precision amplifier family in an 8-pin SOIC; temperature and ordering suffix require verification

📋 참조 대체품 (카탈로그에 없음)

LT1013DN8

✅ 드롭인 ⚠️ 사양 미검증
📦 8-pin SOIC
Same LT1013 family and 8-pin SOIC footprint; ordering and temperature designations differ

📋 참조 대체품 (카탈로그에 없음)

LT1013DS8

✅ 드롭인 ⚠️ 사양 미검증
📦 8-pin SOIC
Same dual precision LT1013 circuit in an 8-pin SOIC; ordering suffix and temperature grade must be confirmed

📋 참조 대체품 (카탈로그에 없음)

LT1013IS8 최대 정격 & 전기적 특성

Amplifier Type Dual precision operational amplifier
Number of Circuits 2
Supply Voltage Range 5 V to 44 V
Single-Supply Operation 5 V
Dual-Supply Operation ±15 V
Maximum Supply Current 500 uA
Open-Loop Gain at 5 mA Load 1.5 million minimum
Open-Loop Gain at 17 mA Load 800,000 minimum
Low-Frequency Noise Density 0.55 uV peak-to-peak (0.1 Hz to 10 Hz)
Current Noise Density 0.07 pA/√Hz
동작 온도 범위 -40 °C to +85 °C
Package Type 8-pin SOIC, 8-SO
Package Dimensions 0.154 in (3.90 mm) width
실장 유형 Surface mount
RoHS 상태 Compliant
Lead-Free Status Yes

LT1013IS8 핀 구성

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
핀 1 OUT A — Amplifier A output
핀 2 -IN A — Amplifier A inverting input
핀 3 +IN A — Amplifier A non-inverting input
핀 4 V- — Negative supply or ground connection
핀 5 +IN B — Amplifier B non-inverting input
핀 6 -IN B — Amplifier B inverting input
핀 7 OUT B — Amplifier B output
핀 8 V+ — Positive supply connection

일반적인 애플리케이션

LT1013IS8 적합 용도: 6 애플리케이션s: Strain-Gauge Bridge Signal Conditioning, Thermocouple and Low-Level Sensor Amplification, 4 mA to 20 mA Current-Loop Transmitter, Battery-Powered Precision Instrumentation, Precision Active Filtering, Threshold Detection and Limit Monitoring.

🏭

Strain-Gauge Bridge Signal Conditioning

The LT1013IS8 fits precision bridge-amplifier inputs because its guaranteed open-loop gain reaches 1.5 million at a 5 mA load and its current noise is 0.07 pA/√Hz. Place one amplifier in the instrumentation configuration and use the second channel for gain or filtering. The high gain reduces error caused by amplifier offset relative to the small bridge excitation signal. Because the amplifier is not rail-to-rail, confirm common-mode and output-swing limits at the bridge excitation voltage before layout release.

🧩

Thermocouple and Low-Level Sensor Amplification

For thermocouple and resistance-sensor front ends, the LT1013IS8 provides the high gain and low noise needed to preserve small differential signals. A 5 mA-load open-loop gain of 1.5 million and 0.55 uV peak-to-peak noise over 0.1 Hz to 10 Hz help limit errors in the microvolt-to-millivolt range. The 500 uA maximum supply current is advantageous in battery-powered field instruments. Place input traces away from heaters, switching regulators, and relay contacts to reduce thermoelectric offset errors.

🏭

4 mA to 20 mA Current-Loop Transmitter

The LT1013IS8 supports the amplifier and buffer stages used in 4 mA-to-20 mA current-loop transmitters. Its high open-loop gain supports accurate closed-loop current control, while the 500 uA maximum supply current reduces the amplifier's contribution to overall transmitter power. The two channels can implement a buffer plus an active filter or error amplifier. Confirm the common-mode range, output-swing capability, and loop bandwidth in the final transmitter topology before production.

🔧

Battery-Powered Precision Instrumentation

The LT1013IS8 is appropriate for portable measurement systems where amplifier current draw competes with sensor and display power budgets. Its guaranteed 500 uA maximum supply current and operation from a 5 V single supply help conserve energy, while the 1.5 million minimum gain at a 5 mA load maintains accuracy in non-inverting and differential stages. Use low-leakage resistors and protective diodes around high-impedance inputs, and verify shutdown behavior if the instrument also uses the second amplifier channel for monitoring.

📡

Precision Active Filtering

The LT1013IS8 can implement precision active filters and multiple gain blocks where component tolerances must not dominate the transfer function. A guaranteed open-loop gain of 1.5 million improves closed-loop accuracy at low frequencies, and the dual package allows two filter sections or a gain block plus buffer. Keep resistor networks close to the amplifier pins and keep the feedback loop compact. Set the noise target against the filter's noise-gain bandwidth rather than using only the signal bandwidth.

⚡

Threshold Detection and Limit Monitoring

The LT1013IS8 supports precision threshold-detection and multiple-limit monitoring circuits where comparator-like functionality requires adjustable gain and signal amplification. The high open-loop gain improves switching repeatability around the reference threshold, and the two channels permit independent detection functions. Use hysteresis where noise could cause repeated output transitions. The 0.55 uV peak-to-peak low-frequency noise specification helps set the minimum detectable signal, while the supply limits must be reviewed for input signals above the common-mode range.

추천 제품 요약

LT1013IS8#PBF Lead-free ordering alternative for the same precision dual amplifier 사용처: Strain-Gauge Bridge Signal Conditioning, Thermocouple and Low-Level Sensor Amplification, Battery-Powered Precision Instrumentation, Precision Active Filtering LT1013IS8 Analog Devices 사용처: Strain-Gauge Bridge Signal Conditioning, 4 mA to 20 mA Current-Loop Transmitter, Battery-Powered Precision Instrumentation, Precision Active Filtering, Threshold Detection and Limit Monitoring LT1013CN8 Same-family LT1013 dual precision amplifier ordering option 사용처: Thermocouple and Low-Level Sensor Amplification LT1013IS8#TR Reel-packed ordering option for automated assembly 사용처: 4 mA to 20 mA Current-Loop Transmitter, Threshold Detection and Limit Monitoring
What is the LT1013IS8 used for?
The LT1013IS8 is a dual precision operational amplifier intended for accurate low-noise signal conditioning. It provides two amplifiers in an 8-pin SOIC package and is suited to strain-gauge, thermocouple, instrumentation, filtering, threshold-detection, and current-loop circuits. According to the Analog Devices LT1013 product page, the device operates from a 5 V single supply to ±15 V and is designed for battery-powered precision instrumentation.
What is the supply voltage range of the LT1013IS8?
The LT1013IS8 operates from 5 V to 44 V across its supply pins. This supports 5 V single-supply systems as well as ±15 V split-supply instrumentation. The manufacturer identifies both 5 V and ±15 V operating conditions in its published specifications. Because the amplifier is not a rail-to-rail-output device, verify the output-swing and input-common-mode limits at the actual supply voltage before selecting the part.
How much supply current does the LT1013IS8 consume?
The LT1013IS8 has a guaranteed maximum supply current of 500 uA. This low consumption is important in battery-powered measurement systems because the amplifier draws power continuously while the instrument is active. Analog Devices lists the maximum supply-current figure on the LT1013 product page, making the device suitable for precision instrumentation designs that prioritize low quiescent current.
What are the key specifications of LT1013IS8 that engineers should know?
The LT1013IS8 is a dual precision op amp with a 5 V to 44 V supply range, 500 uA maximum supply current, and guaranteed open-loop gain of 1.5 million at a 5 mA load. Its noise specifications include 0.55 uV peak-to-peak from 0.1 Hz to 10 Hz and 0.07 pA/√Hz current noise. The package is an 8-pin SOIC, and the specified operating-temperature range is -40 °C to +85 °C.
Where can I download the LT1013IS8 datasheet PDF?
The official LT1013 datasheet and product information are available from the Analog Devices product page at analog.com/en/products/lt1013.html. That page contains the manufacturer specifications for ±15 V and single 5 V operation, a downloadable data sheet, and ordering information for the LT1013 family. Use the manufacturer document for final pin assignments, test conditions, and electrical characteristic limits.
Where can I find the LT1013IS8 pinout?
The LT1013IS8 pinout is shown in the pin-configuration section of the Analog Devices LT1013 data sheet. The device uses the standard 8-pin SOIC dual-amplifier arrangement: amplifier A uses pins 1, 2, and 3, amplifier B uses pins 5, 6, and 7, and the supply pins are 4 and 8. Assign PCB nets from the manufacturer pin-configuration drawing rather than inferring connections from another dual amplifier.
Is the LT1013IS8 suitable for a 5 V single-supply design?
Yes, the LT1013IS8 supports 5 V single-supply operation and is specifically identified by Analog Devices for that configuration. Its guaranteed low supply current of 500 uA maximum and 1.5 million minimum open-loop gain at a 5 mA load support low-power precision measurements. Check the input common-mode and output-swing limits at 5 V so the signal remains inside the linear operating region.
What is the difference between LT1013IS8 and LT1013IS8#PBF?
The LT1013IS8 and LT1013IS8#PBF identify the same LT1013 dual precision operational amplifier in the 8-pin SOIC configuration, with the latter using the lead-free ordering notation. The circuit functions and package pins remain the same for an existing board design. When ordering, confirm the termination code, temperature grade, and delivery format against the distributor part page before releasing the quantity to manufacturing.
What is the best drop-in replacement for the LT1013IS8?
The closest drop-in procurement alternatives are the lead-free LT1013IS8#PBF and the LT1013 family ordering codes that use the same 8-pin SOIC footprint. A valid replacement must preserve the pin arrangement, supply range, amplifier-channel assignment, and precision performance rather than merely using an 8-pin SOIC outline. Request the current manufacturer ordering code and availability through the Request a Quote form on this page.
Can LT1013IS8 be used in a strain-gauge signal conditioner?
Yes, the LT1013IS8 is well suited to strain-gauge signal conditioning because its guaranteed open-loop gain reaches 1.5 million at a 5 mA load. That gain supports high-impedance bridge amplifiers where offset and bias-current errors must remain small. Analog Devices lists strain-gauge signal conditioners and thermocouple amplifiers among the LT1013 application areas, while the 0.07 pA/√Hz current noise benefits high-impedance transducers.
LT1013IS8 versus LM324NSR for precision signal conditioning: which is better?
The LT1013IS8 is the better choice when precision, noise, and gain matter. It provides a guaranteed minimum open-loop gain of 1.5 million at a 5 mA load, 0.55 uV peak-to-peak low-frequency noise, and a 500 uA maximum supply current, while the LM324NSR is a general-purpose amplifier intended for lower-cost signal conditioning. The LM324NSR may still suit noncritical applications, but it does not match the LT1013IS8 precision ratings.
What is the difference between LT1013IS8 and LT1013DS8?
The LT1013IS8 and LT1013DS8 are orderable LT1013 variants associated with different package and temperature designations within the same precision amplifier family. The LT1013IS8 is the industrial-temperature 8-pin SOIC ordering code, and the LT1013DS8 is associated with the SOIC designation used in device cross-reference records. Verify the exact suffix and package drawing in the manufacturer ordering table before treating one as a procurement substitute.
When should I choose the LT1013IS8 instead of a general-purpose op amp?
Choose the LT1013IS8 when the measurement chain requires high open-loop gain, low supply current, and low noise rather than basic amplification. Its 1.5 million minimum gain, 500 uA maximum supply current, and 0.07 pA/√Hz current-noise specification improve accuracy in strain-gauge and thermocouple circuits. A general-purpose amplifier can be more economical when offset, drift, noise, and headroom are not critical.
Where can I buy LT1013IS8 online?
Use the Request a Quote form on this page to request the current price, stock position, lead time, and minimum order quantity for the LT1013IS8. The manufacturer product page and the distributor listing links on this page are useful references for confirming the ordering code and technical identity. Commercial terms can change by quantity and market conditions, so confirm them with a current quotation.
How much does the LT1013IS8 cost?
Current pricing for the LT1013IS8 should be confirmed through the Request a Quote form on this page because distributor pricing changes with quantity, inventory, and contract terms. The manufacturer identifies the LT1013IS8 as an 8-pin SOIC dual precision operational amplifier, but a quotation is the reliable way to obtain the present unit price, volume breaks, and expected delivery date for your production quantity.
What is the lead time and stock status of the LT1013IS8?
Request the current lead time, stock status, and minimum order quantity for the LT1013IS8 through the Request a Quote form on this page. Lifecycle and availability can vary between the original LT1013IS8 ordering code and lead-free variants, so confirm the exact suffix before scheduling production. For time-critical builds, provide your required quantity and target assembly date with the request.
What is the best Analog Devices equivalent for the LT1013IS8?
The closest same-manufacturer ordering alternative is the lead-free LT1013IS8#PBF, which retains the LT1013 family's 8-pin SOIC electrical and pin configuration. Other LT1013 family codes can differ in temperature grade, termination, or delivery format, so verify each against the manufacturer ordering table. The Request a Quote form on this page can confirm current sourcing for the exact suffix needed by your assembly.

엔지니어링 참조 데이터: LT1013IS8 — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the LT1013IS8 for precision signal conditioning where low noise, high open-loop gain, and low supply current are more important than lowest unit cost. It is a strong fit for strain-gauge, thermocouple, current-loop, active-filter, and battery-powered instrumentation circuits. LT1013IS8#PBF is the direct lead-free ordering alternative when the board and bill of materials use the PBF suffix, while LT1013IS8#TR provides the same electrical device in a reel format. LT1013CN8, LT1013DN8, and LT1013DS8 are same-family procurement options that require suffix and temperature-grade confirmation before substitution. Use a general-purpose amplifier such as LM324NSR only when its offset, noise, gain, and current consumption are adequate for the application. In every case, verify supply headroom, common-mode range, output swing, thermal conditions, and exact package drawings before releasing the design.

대체품과의 비교

파라미터 이 제품 LT1013IS8#PBF LT1013IS8#TR LT1013CN8 LT1013DN8 LT1013DS8
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Amplifier Configuration Dual precision operational amplifier Dual precision operational amplifier Dual precision operational amplifier Dual precision operational amplifier Dual precision operational amplifier Dual precision operational amplifier

주요 차별점

  • High guaranteed open-loop gain supports accurate precision feedback stages (vs LM324NSR)
  • Low supply current supports battery-powered instrumentation (vs LM324NSR)
  • Low-frequency noise performance improves microvolt-level conditioning (vs LM324NSR)

설계 노트

Keep the precision feedback network compact and connect each resistor directly to the relevant input or output pin. High-impedance input traces should be short, guarded where practical, and routed away from relay contacts, switching inductors, and power-supply traces. In strain-gauge and thermocouple circuits, even a few millivolts of thermoelectric or leakage-induced error can be significant relative to the sensor signal.

Use the lowest supply voltage that still satisfies the input common-mode, output-swing, and transient requirements. The LT1013IS8 is specified at 500 uA maximum supply current, but total system current also includes resistor dividers, protection devices, and the second amplifier channel. Decouple the supply pins with short ceramic-capacitor connections and verify startup behavior if the input sources can remain energized while the supply is rising.

Do not treat the 1.5 million open-loop gain figure as the closed-loop gain of the assembled circuit. Resistor tolerances, bias-current effects, and noise gain determine the practical accuracy of the gain stage. Check the input bias current, input offset voltage, and temperature drift in the manufacturer data sheet before selecting the feedback resistors, particularly for high-impedance sensor applications.

규정 준수 정보

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
무연
Yes
무할로겐
Unknown
분쟁 광물
Unknown

The manufacturer product page and device records identify the LT1013 family as RoHS compliant with a lead-free ordering option. No specific REACH, halogen-free, conflict-minerals, or automotive-qualification statement is published in the cited product information.

관련 검색

LT1013IS8 LT1013IS8 pbf LT1013IS8 datasheet LT1013IS8 datasheet pdf LT1013IS8 pinout LT1013IS8 equivalent LT1013IS8 replacement LT1013IS8 cross reference LT1013IS8 vs LM324NSR LT1013IS8 SOIC-8 LT1013IS8 precision amplifier LT1013IS8 strain gauge amplifier LT1013IS8 price Analog Devices LT1013IS8 LT1013IS8 current noise

관련 부품 & 용어

Analog Devices LT1013IS8 LT1013IS8#PBF LT1013IS8#TR LT1013CN8 LT1013DN8 LT1013DS8 precision operational amplifier dual operational amplifier voltage-feedback amplifier signal conditioning instrumentation amplifier strain-gauge signal conditioner thermocouple amplifier 4 mA to 20 mA current-loop transmitter active filter open-loop gain output noise current noise common-mode voltage 8-pin SOIC SOIC package family surface-mount integrated circuit RoHS lead-free battery-powered instrumentation
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기