Analog Devices

LT1469CS8 - Dual 90MHz Precision Op Amp | Analog Devices

부품 번호: LT1469CS8 ✓ 활성
350 uV Vdss 8-pin SOIC Package
MOQ: 1 |

LT1469CS8 개요

The Analog Devices LT1469CS8 is a dual, precision, high-speed operational amplifier with two independent amplifier channels, 90 MHz gain-bandwidth product, 22 V/us slew rate, and 16-bit accuracy in an 8-pin SOIC package. It combines low offset voltage, low drift, and 900 ns settling performance for demanding analog signal-chain designs.

An operational amplifier is a voltage-controlled differential amplifier that uses high open-loop gain to amplify small signals. A dual operational amplifier contains two amplifiers in one package, reducing board area while supporting independent signal paths. The LT1469 series belongs to the precision operational-amplifier hierarchy, combining precision and AC performance for ADC buffers, DAC current-to-voltage converters, instrumentation, and active filtering.

The LT1469CS8 provides a 90 MHz gain-bandwidth product and a 22 V/us slew rate. According to the manufacturer product description and datasheet, it achieves 16-bit accuracy and settles to within 150 uV in 900 ns after a 10 V step. These characteristics make the device suitable for high-accuracy systems requiring fast acquisition, accurate current-to-voltage conversion, and low-distortion signal amplification.

Its precision is reflected in a maximum input offset voltage of 350 uV, while the operating temperature range for LT1469CS8 is 0°C to 70°C. The device is supplied in an 8-pin SOIC package measuring 3.90 mm wide. The dual-channel organization allows matched signal conditioning, differential amplifier implementations, or two independent precision amplifier stages without requiring two separate packages.

Typical applications include high-resolution ADC input buffers, DAC current-to-voltage conversion, low-frequency instrumentation, active filters, sample-and-hold signal conditioning, and precision industrial control systems. Its 90 MHz bandwidth supports higher-frequency signals than conventional precision op amps, while the 22 V/us slew rate helps preserve amplitude accuracy on rapidly changing waveforms.

PCB design should keep input and feedback traces short, place compensation and feedback components close to the device, and provide solid ground-plane continuity. Designers should also verify gain stability, output swing, load capability, input common-mode range, and operating-temperature limits against their intended signal and supply conditions.

This product page combines the exact LT1469CS8 specifications, manufacturer documentation, sourcing guidance, package details, and verified drop-in candidates. It is intended to help engineers identify the correct operational amplifier, confirm electrical compatibility, and plan a reliable eight-pin precision analog layout.

드롭인 대체품: LT1469CS8 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

LT1469CS8#PBF

✅ 드롭인
📦 8-pin SOIC
Same dual 90 MHz, 22 V/us amplifier function and 8-pin SOIC footprint; lead-free ordering suffix differs from LT1469CS8

📋 참조 대체품 (카탈로그에 없음)

LT1469CS8#TR

✅ 드롭인
📦 8-pin SOIC
Same dual 90 MHz, 22 V/us amplifier function and 8-pin SOIC footprint; tape-and-reel ordering suffix differs from LT1469CS8

📋 참조 대체품 (카탈로그에 없음)

LT1469CS8#TRPBF

✅ 드롭인
📦 8-pin SOIC
Same dual 90 MHz, 22 V/us amplifier function and 8-pin SOIC footprint; lead-free tape-and-reel ordering suffix differs from LT1469CS8

📋 참조 대체품 (카탈로그에 없음)

LT1469IS8#PBF

✅ 드롭인
📦 8-pin SOIC
Same LT1469 dual precision high-speed amplifier family and 8-pin SOIC footprint; operating-temperature grade differs from the 0°C to 70°C LT1469CS8

📋 참조 대체품 (카탈로그에 없음)

LT1469CS8 최대 정격 & 전기적 특성

Amplifier Type General-purpose precision operational amplifier
Number of Channels 2 channels
Gain-Bandwidth Product 90 MHz
Slew Rate 22 V/us
Accuracy Class 16-bit accuracy
Settling Time 900 ns to 150 uV for a 10 V step
Maximum Input Offset Voltage 350 uV
동작 온도 범위 0°C to 70°C
Package Type 8-pin SOIC
Package Width 3.90 mm
Total Pin Count 8 pins
실장 유형 Surface mount

LT1469CS8 핀 구성

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
핀 1 OUTA — Amplifier A output
핀 2 -INA — Inverting input for amplifier A
핀 3 +INA — Non-inverting input for amplifier A
핀 4 V- — Negative supply connection
핀 5 +INB — Non-inverting input for amplifier B
핀 6 -INB — Inverting input for amplifier B
핀 7 OUTB — Amplifier B output
핀 8 V+ — Positive supply connection

일반적인 애플리케이션

LT1469CS8 적합 용도: 6 애플리케이션s: High-Resolution ADC Input Buffer, DAC Current-to-Voltage Conversion, Precision Instrumentation Signal Conditioning, Active Analog Filtering, Sample-and-Hold Signal Conditioning, Precision Industrial Control Systems.

📊

High-Resolution ADC Input Buffer

The LT1469CS8 fits ADC input stages that require more bandwidth than a conventional precision amplifier while maintaining low-offset accuracy. Its 90 MHz gain-bandwidth product and 22 V/us slew rate allow the amplifier to respond to changing sensor or conversion signals, while the specified 16-bit accuracy supports high-resolution converter designs. Use it as a unity-gain or moderate-gain buffer ahead of an ADC, with short feedback paths and carefully selected anti-alias filtering. The 900 ns settling specification to 150 uV for a 10 V step is particularly relevant when determining acquisition time and the allowable settling interval for the converter.

⚡

DAC Current-to-Voltage Conversion

The LT1469CS8 is well suited to the transimpedance stage of a DAC current-to-voltage converter because the manufacturer identifies this application explicitly. A 90 MHz gain-bandwidth product supports the feedback network required to convert a high-speed current-output DAC into a voltage, and the 22 V/us slew rate helps maintain accurate output transitions. The device's maximum offset voltage of 350 uV contributes directly to output-conversion error and should be included in the system error budget. Component matching, parasitic capacitance, DAC output compliance, and required settling time should be verified together before finalizing the circuit.

🏭

Precision Instrumentation Signal Conditioning

For instrumentation signal conditioning, the LT1469CS8 combines 16-bit accuracy, 90 MHz bandwidth, and fast settling in a compact 8-pin SOIC package. Its two channels can amplify or buffer two related signals, or implement differential conditioning when appropriately configured. The low maximum offset voltage helps preserve small-signal accuracy, while the high bandwidth supports sensors and test signals whose frequency content extends beyond the range of conventional slow-precision amplifiers. Designers should still check input bias current, input common-mode range, noise density, and output-swing requirements because those parameters determine whether the apparently simple dual-amplifier topology preserves the desired measurement accuracy.

🔧

Active Analog Filtering

The LT1469CS8 can implement active filters requiring accurate gain and reasonable bandwidth. Its 90 MHz gain-bandwidth product gives designers more unity-gain bandwidth than a conventional precision op amp, while 16-bit accuracy supports high-resolution signal conditioning around the filter. The 22 V/us slew rate helps reduce amplitude error on large or fast signals, and 900 ns settling behavior supports time-domain measurements. Component tolerances, resistor noise, and capacitor selection should be calculated together with the op amp's gain-bandwidth response. Pay particular attention to loop stability, especially at the highest practical closed-loop gain.

🖥️

Sample-and-Hold Signal Conditioning

The LT1469CS8 is appropriate for buffering and conditioning paths associated with sample-and-hold systems because its 900 ns settling time to 150 uV after a 10 V step provides a defined transient response. The dual channels can serve separate input and hold-stage paths, while 90 MHz bandwidth and 22 V/us slew rate help process high-speed edges. The amplifier's offset voltage contributes directly to the sampled signal, so the 350 uV maximum specification must be evaluated against the system resolution. In addition, verify the switch resistance, holding capacitor, injected charge, leakage, and the required settling time for the complete acquisition chain.

🏭

Precision Industrial Control Systems

The LT1469CS8 supports industrial control and monitoring circuits that need both signal accuracy and bandwidth. Its 0°C to 70°C rating covers commercial-temperature equipment, while the dual 90 MHz, 22 V/us channels can condition control or sensor signals with faster response than slow precision amplifiers. The amplifier may be used around data converters, control loops, and analog monitoring blocks, provided its supply, common-mode input, output swing, and load limits meet the operating point. For installations with wider environmental requirements, select a grade with the appropriate temperature and qualification coverage rather than relying on the commercial LT1469CS8 outside its stated range.

What is the LT1469CS8?
The LT1469CS8 is a dual, precision, high-speed operational amplifier from Analog Devices with two amplifier channels in an 8-pin SOIC package. According to the LT1469 manufacturer datasheet, it combines 90 MHz gain-bandwidth product, 22 V/us slew rate, 16-bit accuracy, and 900 ns settling to 150 uV for a 10 V step. It is intended for precision analog applications such as ADC buffers and DAC current-to-voltage converters.
What are the key specifications of LT1469CS8 that engineers should know?
The principal LT1469CS8 specifications are a 90 MHz gain-bandwidth product, 22 V/us slew rate, 16-bit accuracy, and 900 ns settling to 150 uV after a 10 V step. The device also has a maximum input offset voltage of 350 uV and an operating temperature range of 0°C to 70°C. These figures place it between general-purpose op amps and much slower precision-only amplifiers.
Where can I download the LT1469CS8 datasheet PDF?
The LT1469CS8 datasheet PDF is available from Analog Devices through the manufacturer document URL on this page. The document is titled for the LT1469 dual 90 MHz, 22 V/us, 16-bit accurate operational amplifier and includes the authoritative electrical characteristics, package details, and application information. Use the manufacturer's pin-description table when assigning PCB connections.
Where can I find the LT1469CS8 pinout?
The LT1469CS8 uses an 8-pin SOIC pinout with two complete operational-amplifier channels. Pins 1 and 8 provide the two outputs, pins 2 and 6 are the inverting inputs, pins 3 and 5 are the non-inverting inputs, and pin 4 connects to the negative supply while pin 8 connects to the positive supply. Confirm all connections against the manufacturer datasheet before fabrication.
Is the LT1469CS8 suitable for ADC buffers?
The LT1469CS8 is suitable for precision ADC buffers because its 90 MHz gain-bandwidth product and 22 V/us slew rate support fast signals while its 16-bit accuracy and 350 uV maximum input offset voltage address precision requirements. The manufacturer identifies ADC buffering as a key application. Confirm the ADC input range and settling requirements at the selected gain before finalizing the filter and feedback network.
Can the LT1469CS8 be used in a DAC current-to-voltage converter?
The LT1469CS8 can be used in a DAC current-to-voltage converter because the manufacturer identifies that application specifically. Its 90 MHz bandwidth accommodates high-speed feedback networks, while the 22 V/us slew rate and 900 ns settling behavior help reduce conversion timing error. Choose resistor values and output loading carefully because noise, offset, and capacitive loading all affect the realized converter accuracy.
What is the difference between LT1469CS8 and LT1469CS8#PBF?
The LT1469CS8 and LT1469CS8#PBF identify closely related orderable versions of the same LT1469 dual amplifier, with the main documented distinction being the orderable suffix and associated packaging or lead-free ordering information. The electrical device function remains a dual 90 MHz, 22 V/us precision operational amplifier. When replacing an existing board, compare the complete ordering suffix, temperature grade, package, and marking requirements.
LT1469CS8 vs LT1469-2 — which is better for a precision amplifier design?
The LT1469CS8 is the general choice for precision high-speed amplifier designs, while the LT1469-2 is a decompensated variant intended to be stable at gain 2 or greater. According to the LT1469-2 manufacturer product description, its decompensation changes the minimum stable gain rather than merely changing the package. Choose LT1469-2 only when its gain-stability requirement matches the circuit.
When should I choose LT1469CS8 over LT1469IS8#PBF?
Choose LT1469CS8 for a commercial-temperature design whose operating range remains within 0°C to 70°C. Choose LT1469IS8#PBF when the application requires the temperature grade associated with that ordering option and the complete suffix has been validated for production. The amplifier function and eight-pin package family are comparable, but operating temperature and qualification requirements must drive the final choice.
What can replace LT1469CS8 on an existing PCB?
The closest documented drop-in choices for an LT1469CS8 board are the LT1469CS8#PBF and LT1469CS8#TR orderable versions because they retain the eight-pin SOIC footprint and the same dual 90 MHz, 22 V/us amplifier function. No verified cross-brand, pin-compatible replacement is established by the cross-reference results. Confirm the exact ordering suffix, temperature range, and stability requirements before substituting any part.
Is LT1469CS8 the same as LT1469IS8#PBF?
The LT1469CS8 and LT1469IS8#PBF are related dual precision high-speed operational amplifiers, but they should not be treated as automatically identical. The LT1469CS8 is documented for 0°C to 70°C, while the IS8 ordering option represents a different grade designation. Verify temperature range, package, offset limits, and qualification requirements against the complete manufacturer ordering information.
Where to buy LT1469CS8 online?
The LT1469CS8 can be requested through the Request a Quote form on this page, where the required package, suffix, quantity, and delivery information should be specified. This page does not maintain a live stock counter. For a production order, identify LT1469CS8 exactly and confirm whether a lead-free ordered suffix is required by your assembly and documentation process.
What is the price of LT1469CS8?
Current LT1469CS8 commercial terms are provided through the Request a Quote form on this page. The quote can account for the exact ordering suffix, package form, quantity, and requested delivery terms. Confirm the orderable suffix before submission because LT1469CS8, LT1469CS8#PBF, and LT1469CS8#TR can have different ordering or packing implications.
What is the lead time for LT1469CS8?
Request the current LT1469CS8 lead time through the Request a Quote form on this page. Lead time depends on the exact suffix, order quantity, manufacturing status, and delivery requirements. For prototype builds, identify whether the board accepts the standard eight-pin SOIC footprint and whether lead-free marking is required before placing the order.
Is LT1469CS8 in stock?
Use the Request a Quote form on this page to request current LT1469CS8 availability and a confirmed delivery schedule. The page does not publish a real-time inventory guarantee. State the exact required suffix, quantity, package form, and target date so the commercial response reflects the configuration your assembly can actually accept.

엔지니어링 참조 데이터: LT1469CS8 — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose LT1469CS8 when the circuit needs a dual precision amplifier combining a 90 MHz gain-bandwidth product, 22 V/us slew rate, and low maximum offset voltage of 350 uV within a 0°C to 70°C operating environment. Its two channels are useful for ADC buffering, DAC current-to-voltage conversion, active filtering, and instrumentation. LT1469CS8#PBF is the relevant choice when a lead-free ordering designation is required, while LT1469CS8#TR and LT1469CS8#TRPBF support tape-and-reel assembly requirements with the same core amplifier performance. Select LT1469IS8#PBF when its wider temperature grade is required and the complete ordering information has been validated. The LT1469-2 should not be treated as an automatic substitution because it is decompensated for stable operation at gain 2 or greater. No cross-brand part is recommended without a manufacturer-confirmed pinout and electrical comparison.

대체품과의 비교

파라미터 이 제품 LT1469CS8#PBF LT1469CS8#TR LT1469CS8#TRPBF LT1469IS8#PBF
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Amplifier Channels 2 2 2 2 2
Gain-Bandwidth Product 90 MHz 90 MHz 90 MHz 90 MHz 90 MHz
Slew Rate 22 V/us 22 V/us 22 V/us 22 V/us 22 V/us
Accuracy 16-bit accurate 16-bit accurate 16-bit accurate 16-bit accurate 16-bit accurate
Settling 900 ns to 150 uV for a 10 V step 900 ns to 150 uV for a 10 V step 900 ns to 150 uV for a 10 V step 900 ns to 150 uV for a 10 V step 900 ns to 150 uV for a 10 V step

주요 차별점

  • Combines precision and high-speed amplification in one dual package (vs LT1469CS8#PBF)
  • Commercial-temperature grade is suitable for standard office and commercial equipment (vs LT1469IS8#PBF)
  • Supports two independent precision amplifier channels in an 8-pin package (vs LT1469CS8#TRPBF)

설계 노트

Route each amplifier's input and feedback components close to their associated pins. Keep the feedback loop compact, maintain a continuous ground reference beneath the package, and avoid routing high-speed or switching-current paths beneath the SOIC footprint. The dual layout should keep amplifier A and amplifier B return currents separated where practical, particularly when one channel handles a fast high-amplitude signal and the other processes a small precision signal.

Evaluate closed-loop bandwidth and phase margin at the highest gain used in the design. The LT1469CS8 has a 90 MHz gain-bandwidth product, but the realized response also depends on feedback resistance, capacitance, load capacitance, and source impedance. Add or adjust compensation only after measuring or calculating the complete network, and confirm stability across the intended supply-voltage and temperature ranges rather than relying on the gain-bandwidth figure alone.

Do not treat the 16-bit accuracy description as a guaranteed 16-bit converter result. Overall accuracy also depends on offset voltage, bias current, noise, drift, resistor and capacitor tolerances, reference accuracy, and output-loading conditions. The maximum input offset voltage of 350 uV should be included in the error budget, while supply voltage, input common-mode range, and output swing must be checked against the actual signal.

Place supply-decoupling capacitors close to the positive and negative pins, with the ground return kept short and low-impedance. The LT1469CS8 operates from dual supplies, so both rails require stable reference planes. Verify that source and sink current remain suitable for the output stage at the selected frequency and load, and use resistor isolation if capacitive loading could impair settling or stability.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

The base LT1469CS8 ordering information does not explicitly establish the requested compliance fields. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification status from the exact orderable suffix and current manufacturer documentation.

관련 검색

lt1469cs8 pbf LT1469CS8 datasheet LT1469CS8 datasheet pdf LT1469CS8 pinout LT1469CS8 specifications LT1469CS8 90MHz op amp LT1469CS8 8-SOIC LT1469CS8 ADC buffer LT1469CS8 DAC current to voltage LT1469CS8 vs LT1469-2 LT1469CS8 equivalent LT1469CS8 replacement LT1469CS8 price Analog Devices LT1469CS8

관련 부품 & 용어

Analog Devices Linear Technology LT1469CS8 LT1469CS8#PBF LT1469CS8#TR LT1469CS8#TRPBF LT1469IS8#PBF LT1469-2 LT1469 operational amplifier precision operational amplifier dual amplifier gain-bandwidth product slew rate settling time input offset voltage common-mode voltage ADC buffer DAC current-to-voltage converter active filter instrumentation amplifier 8-pin SOIC SOIC family surface-mount package analog signal chain
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기